From c29f40ca19b8ca284a2d1415e26b802bc9b2fb67 Mon Sep 17 00:00:00 2001 From: Alexander Duyck Date: Tue, 6 Mar 2012 07:52:38 +0000 Subject: ixgbe: Fix issues with SR-IOV loopback when flow control is disabled This patch allows us to avoid a Tx hang when SR-IOV is enabled. This hang can be triggered by sending small packets at a rate that was triggering Rx missed errors from the adapter while the internal Tx switch and at least one VF are enabled. This was all due to the fact that under heavy stress the Rx FIFO never drained below the flow control high water mark. This resulted in the Tx FIFO being head of line blocked due to the fact that it relies on the flow control high water mark to determine when it is acceptable for the Tx to place a packet in the Rx FIFO. The resolution for this is to set the FCRTH value to the RXPBSIZE - 32 so that even if the ring is almost completely full we can still place Tx packets on the Rx ring and drop incoming Rx traffic if we do not have sufficient space available in the Rx FIFO. Signed-off-by: Alexander Duyck Tested-by: Sibai Li Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/ixgbe/ixgbe_common.c | 9 ++++++++- 1 file changed, 8 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c index 383b9413292e..7d81bee4f681 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_common.c @@ -2011,13 +2011,20 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num) IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg); IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg); - fcrth = hw->fc.high_water[packetbuf_num] << 10; fcrtl = hw->fc.low_water << 10; if (hw->fc.current_mode & ixgbe_fc_tx_pause) { + fcrth = hw->fc.high_water[packetbuf_num] << 10; fcrth |= IXGBE_FCRTH_FCEN; if (hw->fc.send_xon) fcrtl |= IXGBE_FCRTL_XONE; + } else { + /* + * If Tx flow control is disabled, set our high water mark + * to Rx FIFO size minus 32 in order prevent Tx switch + * loopback from stalling on DMA. + */ + fcrth = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(packetbuf_num)) - 32; } IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(packetbuf_num), fcrth); -- cgit v1.2.3 From 0646819cd31786f4b024d0056f73adf460be40aa Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Fri, 16 Mar 2012 00:18:49 +0000 Subject: net: do not do gso for CHECKSUM_UNNECESSARY in netif_needs_gso This is related to fixing the bug of dropping FCoE frames when disabling tx ip checksum by 'ethtool -K ethx tx off'. The FCoE protocol stack driver would use CHECKSUM_UNNECESSARY on tx path instead of CHECKSUM_PARTIAL (as indicated in the 2/2 of this series). To do so, netif_needs_gso() has to be changed here to not do gso for both CHECKSUM_PARTIAL and CHECKSUM_UNNECESSARY. Ref. to original discussion thread: http://patchwork.ozlabs.org/patch/146567/ Signed-off-by: Yi Zou Tested-by: Ross Brattain Signed-off-by: Jeff Kirsher --- include/linux/netdevice.h | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/include/linux/netdevice.h b/include/linux/netdevice.h index 0eac07c95255..c1b2b5ff7890 100644 --- a/include/linux/netdevice.h +++ b/include/linux/netdevice.h @@ -2636,7 +2636,8 @@ static inline int netif_needs_gso(struct sk_buff *skb, netdev_features_t features) { return skb_is_gso(skb) && (!skb_gso_ok(skb, features) || - unlikely(skb->ip_summed != CHECKSUM_PARTIAL)); + unlikely((skb->ip_summed != CHECKSUM_PARTIAL) && + (skb->ip_summed != CHECKSUM_UNNECESSARY))); } static inline void netif_set_gso_max_size(struct net_device *dev, -- cgit v1.2.3 From c98291ee1ceac03912e24b3219fa6e7dc0d52f5e Mon Sep 17 00:00:00 2001 From: Yi Zou Date: Fri, 16 Mar 2012 00:18:54 +0000 Subject: fcoe: use CHECKSUM_UNNECESSARY instead of CHECKSUM_PARTIAL on tx Fix a bug when using 'ethtool -K ethx tx off' to turn off tx ip checksum, FCoE CRC offload should not be impacte. The skb_checksum_help() is needed only if it's not FCoE traffic for ip checksum, regardless of ethtool toggling the tx ip checksum on or off. Instead of using CHECKSUM_PARTIAL, we will use CHECKSUM_UNNECESSARY as a proper indication to avoid sw ip checksum on FCoE frames. Ref. to original discussion thread: http://patchwork.ozlabs.org/patch/146567/ CC: "James E.J. Bottomley" CC: Robert Love Signed-off-by: Yi Zou Tested-by: Ross Brattain Signed-off-by: Jeff Kirsher --- drivers/scsi/fcoe/fcoe.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/scsi/fcoe/fcoe.c b/drivers/scsi/fcoe/fcoe.c index e9599600aa23..c164890224d2 100644 --- a/drivers/scsi/fcoe/fcoe.c +++ b/drivers/scsi/fcoe/fcoe.c @@ -1498,7 +1498,7 @@ static int fcoe_xmit(struct fc_lport *lport, struct fc_frame *fp) /* crc offload */ if (likely(lport->crc_offload)) { - skb->ip_summed = CHECKSUM_PARTIAL; + skb->ip_summed = CHECKSUM_UNNECESSARY; skb->csum_start = skb_headroom(skb); skb->csum_offset = skb->len; crc = 0; -- cgit v1.2.3 From 883a649b737cdbe3ede7e50f3f939fd706ed5c4e Mon Sep 17 00:00:00 2001 From: Stanislaw Gruszka Date: Tue, 13 Mar 2012 16:11:27 +0100 Subject: iwlegacy: do not nulify il->vif on reset This il->vif is dereferenced in different part of iwlegacy code, so do not nullify it. This should fix random crashes observed in companion with microcode errors i.e. crash in il3945_config_ap(). Additionally this should address also WARNING: at drivers/net/wireless/iwlegacy/common.c:4656 il_mac_remove_interface at least one of the possible reasons of that warning. Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka Signed-off-by: John W. Linville --- drivers/net/wireless/iwlegacy/3945-mac.c | 2 -- drivers/net/wireless/iwlegacy/4965-mac.c | 2 -- drivers/net/wireless/iwlegacy/common.c | 15 ++++++++++++--- 3 files changed, 12 insertions(+), 7 deletions(-) diff --git a/drivers/net/wireless/iwlegacy/3945-mac.c b/drivers/net/wireless/iwlegacy/3945-mac.c index 0c1209390169..faec40467208 100644 --- a/drivers/net/wireless/iwlegacy/3945-mac.c +++ b/drivers/net/wireless/iwlegacy/3945-mac.c @@ -2673,8 +2673,6 @@ il3945_bg_restart(struct work_struct *data) if (test_and_clear_bit(S_FW_ERROR, &il->status)) { mutex_lock(&il->mutex); - /* FIXME: vif can be dereferenced */ - il->vif = NULL; il->is_open = 0; mutex_unlock(&il->mutex); il3945_down(il); diff --git a/drivers/net/wireless/iwlegacy/4965-mac.c b/drivers/net/wireless/iwlegacy/4965-mac.c index 7b54dbb338be..b88bb2734197 100644 --- a/drivers/net/wireless/iwlegacy/4965-mac.c +++ b/drivers/net/wireless/iwlegacy/4965-mac.c @@ -5651,8 +5651,6 @@ il4965_bg_restart(struct work_struct *data) if (test_and_clear_bit(S_FW_ERROR, &il->status)) { mutex_lock(&il->mutex); - /* FIXME: do we dereference vif without mutex locked ? */ - il->vif = NULL; il->is_open = 0; __il4965_down(il); diff --git a/drivers/net/wireless/iwlegacy/common.c b/drivers/net/wireless/iwlegacy/common.c index e5ac04739bcc..6a692a534ffc 100644 --- a/drivers/net/wireless/iwlegacy/common.c +++ b/drivers/net/wireless/iwlegacy/common.c @@ -4508,6 +4508,7 @@ il_mac_add_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif) { struct il_priv *il = hw->priv; int err; + bool reset; mutex_lock(&il->mutex); D_MAC80211("enter: type %d, addr %pM\n", vif->type, vif->addr); @@ -4518,7 +4519,12 @@ il_mac_add_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif) goto out; } - if (il->vif) { + /* + * We do not support multiple virtual interfaces, but on hardware reset + * we have to add the same interface again. + */ + reset = (il->vif == vif); + if (il->vif && !reset) { err = -EOPNOTSUPP; goto out; } @@ -4528,8 +4534,11 @@ il_mac_add_interface(struct ieee80211_hw *hw, struct ieee80211_vif *vif) err = il_set_mode(il); if (err) { - il->vif = NULL; - il->iw_mode = NL80211_IFTYPE_STATION; + IL_WARN("Fail to set mode %d\n", vif->type); + if (!reset) { + il->vif = NULL; + il->iw_mode = NL80211_IFTYPE_STATION; + } } out: -- cgit v1.2.3 From 2ee0a07028d2cde6e131b73f029dae2b93c50f3a Mon Sep 17 00:00:00 2001 From: Rajkumar Manoharan Date: Thu, 15 Mar 2012 06:08:04 +0530 Subject: ath9k: fix max noise floor threshold Currently the maximum noise floor limit is set as too high (-60dB). The assumption of having a higher threshold limit is that it would help de-sensitize the receiver (reduce phy errors) from continuous interference. But when we have a bursty interference where there are collisions and then free air time and if the receiver is desensitized too much, it will miss the normal packets too. Lets make use of chips specific min, nom and max limits always. This patch helps to improve the connection stability in congested networks. Cc: stable@vger.kernel.org Cc: Paul Stewart Tested-by: Gary Morain Signed-off-by: Madhan Jaganathan Signed-off-by: Rajkumar Manoharan Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/calib.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-) diff --git a/drivers/net/wireless/ath/ath9k/calib.c b/drivers/net/wireless/ath/ath9k/calib.c index 2f4b48e6fb03..e5cceb077574 100644 --- a/drivers/net/wireless/ath/ath9k/calib.c +++ b/drivers/net/wireless/ath/ath9k/calib.c @@ -20,7 +20,6 @@ /* Common calibration code */ -#define ATH9K_NF_TOO_HIGH -60 static int16_t ath9k_hw_get_nf_hist_mid(int16_t *nfCalBuffer) { @@ -346,10 +345,10 @@ static void ath9k_hw_nf_sanitize(struct ath_hw *ah, s16 *nf) "NF calibrated [%s] [chain %d] is %d\n", (i >= 3 ? "ext" : "ctl"), i % 3, nf[i]); - if (nf[i] > ATH9K_NF_TOO_HIGH) { + if (nf[i] > limit->max) { ath_dbg(common, CALIBRATE, "NF[%d] (%d) > MAX (%d), correcting to MAX\n", - i, nf[i], ATH9K_NF_TOO_HIGH); + i, nf[i], limit->max); nf[i] = limit->max; } else if (nf[i] < limit->min) { ath_dbg(common, CALIBRATE, -- cgit v1.2.3 From e92109be7a6a04808c3ed586475ba1e5ea56ecbd Mon Sep 17 00:00:00 2001 From: Stanislaw Gruszka Date: Thu, 15 Mar 2012 11:42:49 +0100 Subject: iwlegacy: fix BSSID setting Current commit 0775f9f90cdaf40fbf69b3192b3dddb2b3436f45 "mac80211: remove spurious BSSID change flag" exposed bug on iwlegacy, that we do not set BSSID address correctly and then device was not able to receive frames after successful associate. On the way fix scan canceling comment. Apparently ->post_associate() do cancel scan itself, but scan cancel on BSS_CHANGED_BSSID is needed. I'm not sure why, but when I removed it, I had frequent auth failures: wlan4: send auth to 54:e6:fc:98:63:fe (try 1/3) wlan4: send auth to 54:e6:fc:98:63:fe (try 2/3) wlan4: send auth to 54:e6:fc:98:63:fe (try 3/3) wlan4: authentication with 54:e6:fc:98:63:fe timed out Signed-off-by: Stanislaw Gruszka Signed-off-by: John W. Linville --- drivers/net/wireless/iwlegacy/common.c | 16 ++++++---------- 1 file changed, 6 insertions(+), 10 deletions(-) diff --git a/drivers/net/wireless/iwlegacy/common.c b/drivers/net/wireless/iwlegacy/common.c index 6a692a534ffc..eaf249452e51 100644 --- a/drivers/net/wireless/iwlegacy/common.c +++ b/drivers/net/wireless/iwlegacy/common.c @@ -5288,9 +5288,9 @@ il_mac_bss_info_changed(struct ieee80211_hw *hw, struct ieee80211_vif *vif, D_MAC80211("BSSID %pM\n", bss_conf->bssid); /* - * If there is currently a HW scan going on in the - * background then we need to cancel it else the RXON - * below/in post_associate will fail. + * If there is currently a HW scan going on in the background, + * then we need to cancel it, otherwise sometimes we are not + * able to authenticate (FIXME: why ?) */ if (il_scan_cancel_timeout(il, 100)) { D_MAC80211("leave - scan abort failed\n"); @@ -5299,14 +5299,10 @@ il_mac_bss_info_changed(struct ieee80211_hw *hw, struct ieee80211_vif *vif, } /* mac80211 only sets assoc when in STATION mode */ - if (vif->type == NL80211_IFTYPE_ADHOC || bss_conf->assoc) { - memcpy(il->staging.bssid_addr, bss_conf->bssid, - ETH_ALEN); + memcpy(il->staging.bssid_addr, bss_conf->bssid, ETH_ALEN); - /* currently needed in a few places */ - memcpy(il->bssid, bss_conf->bssid, ETH_ALEN); - } else - il->staging.filter_flags &= ~RXON_FILTER_ASSOC_MSK; + /* FIXME: currently needed in a few places */ + memcpy(il->bssid, bss_conf->bssid, ETH_ALEN); } /* -- cgit v1.2.3 From 66266b3ab4871958ed6a1e43f502cadaf3becfc8 Mon Sep 17 00:00:00 2001 From: "John W. Linville" Date: Thu, 15 Mar 2012 13:25:41 -0400 Subject: cfg80211: allow CFG80211_SIGNAL_TYPE_UNSPEC in station_info The station_info struct had demanded dBm signal values, but the cfg80211 wireless extensions implementation was also accepting "unspecified" (i.e. RSSI) unit values while the nl80211 code was completely unaware of them. Resolve this by formally allowing the "unspecified" units while making nl80211 ignore them. Signed-off-by: John W. Linville Reviewed-by: Johannes Berg --- include/net/cfg80211.h | 6 ++++-- net/wireless/nl80211.c | 29 +++++++++++++++++++---------- 2 files changed, 23 insertions(+), 12 deletions(-) diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 69b7ad3a9925..5ccac722739f 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -619,8 +619,10 @@ struct sta_bss_parameters { * @llid: mesh local link id * @plid: mesh peer link id * @plink_state: mesh peer link state - * @signal: signal strength of last received packet in dBm - * @signal_avg: signal strength average in dBm + * @signal: the signal strength, type depends on the wiphy's signal_type + NOTE: For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_. + * @signal_avg: avg signal strength, type depends on the wiphy's signal_type + NOTE: For CFG80211_SIGNAL_TYPE_MBM, value is expressed in _dBm_. * @txrate: current unicast bitrate from this station * @rxrate: current unicast bitrate to this station * @rx_packets: packets received from this station diff --git a/net/wireless/nl80211.c b/net/wireless/nl80211.c index 4c1eb9472ddb..e49da2797022 100644 --- a/net/wireless/nl80211.c +++ b/net/wireless/nl80211.c @@ -2386,7 +2386,9 @@ nla_put_failure: } static int nl80211_send_station(struct sk_buff *msg, u32 pid, u32 seq, - int flags, struct net_device *dev, + int flags, + struct cfg80211_registered_device *rdev, + struct net_device *dev, const u8 *mac_addr, struct station_info *sinfo) { void *hdr; @@ -2425,12 +2427,18 @@ static int nl80211_send_station(struct sk_buff *msg, u32 pid, u32 seq, if (sinfo->filled & STATION_INFO_PLINK_STATE) NLA_PUT_U8(msg, NL80211_STA_INFO_PLINK_STATE, sinfo->plink_state); - if (sinfo->filled & STATION_INFO_SIGNAL) - NLA_PUT_U8(msg, NL80211_STA_INFO_SIGNAL, - sinfo->signal); - if (sinfo->filled & STATION_INFO_SIGNAL_AVG) - NLA_PUT_U8(msg, NL80211_STA_INFO_SIGNAL_AVG, - sinfo->signal_avg); + switch (rdev->wiphy.signal_type) { + case CFG80211_SIGNAL_TYPE_MBM: + if (sinfo->filled & STATION_INFO_SIGNAL) + NLA_PUT_U8(msg, NL80211_STA_INFO_SIGNAL, + sinfo->signal); + if (sinfo->filled & STATION_INFO_SIGNAL_AVG) + NLA_PUT_U8(msg, NL80211_STA_INFO_SIGNAL_AVG, + sinfo->signal_avg); + break; + default: + break; + } if (sinfo->filled & STATION_INFO_TX_BITRATE) { if (!nl80211_put_sta_rate(msg, &sinfo->txrate, NL80211_STA_INFO_TX_BITRATE)) @@ -2523,7 +2531,7 @@ static int nl80211_dump_station(struct sk_buff *skb, if (nl80211_send_station(skb, NETLINK_CB(cb->skb).pid, cb->nlh->nlmsg_seq, NLM_F_MULTI, - netdev, mac_addr, + dev, netdev, mac_addr, &sinfo) < 0) goto out; @@ -2568,7 +2576,7 @@ static int nl80211_get_station(struct sk_buff *skb, struct genl_info *info) return -ENOMEM; if (nl80211_send_station(msg, info->snd_pid, info->snd_seq, 0, - dev, mac_addr, &sinfo) < 0) { + rdev, dev, mac_addr, &sinfo) < 0) { nlmsg_free(msg); return -ENOBUFS; } @@ -7596,7 +7604,8 @@ void nl80211_send_sta_event(struct cfg80211_registered_device *rdev, if (!msg) return; - if (nl80211_send_station(msg, 0, 0, 0, dev, mac_addr, sinfo) < 0) { + if (nl80211_send_station(msg, 0, 0, 0, + rdev, dev, mac_addr, sinfo) < 0) { nlmsg_free(msg); return; } -- cgit v1.2.3 From 195ca3b122c02cf21ce64f211d9474600da80e80 Mon Sep 17 00:00:00 2001 From: Rajkumar Manoharan Date: Thu, 15 Mar 2012 23:05:28 +0530 Subject: ath9k: reduce listen time period When we have downlink traffic alone and the station is going thru bgscan, the client is out of operating channel for around 1000ms which is too long. The mac80211 decides when to switch back to oper channel based on tx queue, bad latency and listen time. As the station does not have tx traffic, the bgscan can easily affect downlink throughput. By reducing the listen time, it helps the associated AP to retain the downstream rate. Cc: Paul Stewart Tested-by: Gary Morain Signed-off-by: Rajkumar Manoharan Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/init.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/wireless/ath/ath9k/init.c b/drivers/net/wireless/ath/ath9k/init.c index 60159f4ee532..cb006458fc4b 100644 --- a/drivers/net/wireless/ath/ath9k/init.c +++ b/drivers/net/wireless/ath/ath9k/init.c @@ -680,7 +680,7 @@ void ath9k_set_hw_capab(struct ath_softc *sc, struct ieee80211_hw *hw) hw->queues = 4; hw->max_rates = 4; hw->channel_change_time = 5000; - hw->max_listen_interval = 10; + hw->max_listen_interval = 1; hw->max_rate_tries = 10; hw->sta_data_size = sizeof(struct ath_node); hw->vif_data_size = sizeof(struct ath_vif); -- cgit v1.2.3 From b5447ff92b5169eab843a76d83e98d0cd7b7f5b6 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Thu, 15 Mar 2012 13:43:29 -0700 Subject: ath9k: fix a memory leak in ath_rx_tasklet() commit 0d95521ea7 (ath9k: use split rx buffers to get rid of order-1 skb allocations) added in memory leak in error path. sc->rx.frag should be cleared after the pskb_expand_head() call, or else we jump to requeue_drop_frag and leak an skb. Signed-off-by: Eric Dumazet Cc: Jouni Malinen Cc: Felix Fietkau Cc: John W. Linville Cc: Trond Wuellner Cc: Grant Grundler Cc: Paul Stewart Cc: David Miller Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/recv.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/ath/ath9k/recv.c b/drivers/net/wireless/ath/ath9k/recv.c index f4ae3ba994a8..1c4583c7ff7c 100644 --- a/drivers/net/wireless/ath/ath9k/recv.c +++ b/drivers/net/wireless/ath/ath9k/recv.c @@ -1913,13 +1913,13 @@ int ath_rx_tasklet(struct ath_softc *sc, int flush, bool hp) if (sc->rx.frag) { int space = skb->len - skb_tailroom(hdr_skb); - sc->rx.frag = NULL; - if (pskb_expand_head(hdr_skb, 0, space, GFP_ATOMIC) < 0) { dev_kfree_skb(skb); goto requeue_drop_frag; } + sc->rx.frag = NULL; + skb_copy_from_linear_data(skb, skb_put(hdr_skb, skb->len), skb->len); dev_kfree_skb_any(skb); -- cgit v1.2.3 From b603c03e9534b9bec19ebf8c42bf217fd875ee65 Mon Sep 17 00:00:00 2001 From: Eliad Peller Date: Sun, 18 Mar 2012 14:08:50 +0200 Subject: mac80211: remove outdated comment The on-oper-channel optimization was reverted, so remove the outdated comment as well. Signed-off-by: Eliad Peller Signed-off-by: John W. Linville --- net/mac80211/main.c | 3 --- 1 file changed, 3 deletions(-) diff --git a/net/mac80211/main.c b/net/mac80211/main.c index b581a24fa15c..16336480c631 100644 --- a/net/mac80211/main.c +++ b/net/mac80211/main.c @@ -102,9 +102,6 @@ int ieee80211_hw_config(struct ieee80211_local *local, u32 changed) might_sleep(); - /* If this off-channel logic ever changes, ieee80211_on_oper_channel - * may need to change as well. - */ offchannel_flag = local->hw.conf.flags & IEEE80211_CONF_OFFCHANNEL; if (local->scan_channel) { chan = local->scan_channel; -- cgit v1.2.3 From b9fc106108f3faf2e4430c3bd5721677c3d6a4a1 Mon Sep 17 00:00:00 2001 From: Stanislaw Gruszka Date: Mon, 19 Mar 2012 09:39:45 +0100 Subject: rt2x00: rt2800usb: schedule txdone work on timeout This is fix for my current commit ed61e2b02027935520d1be884fac0b2ffce8379a "rt2x00: rt2800usb: rework txdone code" We should schedule txdone work on timeout, otherwise if newer get tx status from hardware, we will never report tx status to mac80211 and eventually never wakeup tx queue. Reported-by: Jakub Kicinski Signed-off-by: Stanislaw Gruszka Acked-by: Gertjan van Wingerde Signed-off-by: John W. Linville --- drivers/net/wireless/rt2x00/rt2800usb.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/drivers/net/wireless/rt2x00/rt2800usb.c b/drivers/net/wireless/rt2x00/rt2800usb.c index cd490abced91..f97f84606f56 100644 --- a/drivers/net/wireless/rt2x00/rt2800usb.c +++ b/drivers/net/wireless/rt2x00/rt2800usb.c @@ -163,7 +163,13 @@ static bool rt2800usb_tx_sta_fifo_read_completed(struct rt2x00_dev *rt2x00dev, /* Reschedule urb to read TX status again instantly */ return true; - } else if (rt2800usb_txstatus_pending(rt2x00dev)) { + } + + /* Check if there is any entry that timedout waiting on TX status */ + if (rt2800usb_txstatus_timeout(rt2x00dev)) + queue_work(rt2x00dev->workqueue, &rt2x00dev->txdone_work); + + if (rt2800usb_txstatus_pending(rt2x00dev)) { /* Read register after 250 us */ hrtimer_start(&rt2x00dev->txstatus_timer, ktime_set(0, 250000), HRTIMER_MODE_REL); -- cgit v1.2.3 From 4e808a38fdcaeeeddbc05942623279ebe7c02373 Mon Sep 17 00:00:00 2001 From: Stanislaw Gruszka Date: Mon, 19 Mar 2012 15:59:41 +0100 Subject: rt2x00: rt2800usb: fix status register reread logic Another good catch from Jakub Kicinski. This patch fixes my recent commit: ed61e2b02027935520d1be884fac0b2ffce8379a "rt2x00: rt2800usb: rework txdone code" We should reread status register only when nobody else start already reading status i.e. test_and_set_bit(TX_STATUS_READING, flags) return 0. Reported-by: Jakub Kicinski Signed-off-by: Stanislaw Gruszka Acked-by: Gertjan van Wingerde Signed-off-by: John W. Linville --- drivers/net/wireless/rt2x00/rt2800usb.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/wireless/rt2x00/rt2800usb.c b/drivers/net/wireless/rt2x00/rt2800usb.c index f97f84606f56..001735f7a661 100644 --- a/drivers/net/wireless/rt2x00/rt2800usb.c +++ b/drivers/net/wireless/rt2x00/rt2800usb.c @@ -184,7 +184,7 @@ stop_reading: * here again if status reading is needed. */ if (rt2800usb_txstatus_pending(rt2x00dev) && - test_and_set_bit(TX_STATUS_READING, &rt2x00dev->flags)) + !test_and_set_bit(TX_STATUS_READING, &rt2x00dev->flags)) return true; else return false; -- cgit v1.2.3 From d72308bff5c2fa207949a5925b020bce74495e33 Mon Sep 17 00:00:00 2001 From: Stanislaw Gruszka Date: Mon, 19 Mar 2012 16:00:26 +0100 Subject: mac80211: fix possible tid_rx->reorder_timer use after free Is possible that we will arm the tid_rx->reorder_timer after del_timer_sync() in ___ieee80211_stop_rx_ba_session(). We need to stop timer after RCU grace period finish, so move it to ieee80211_free_tid_rx(). Timer will not be armed again, as rcu_dereference(sta->ampdu_mlme.tid_rx[tid]) will return NULL. Debug object detected problem with the following warning: ODEBUG: free active (active state 0) object type: timer_list hint: sta_rx_agg_reorder_timer_expired+0x0/0xf0 [mac80211] Bug report (with all warning messages): https://bugzilla.redhat.com/show_bug.cgi?id=804007 Reported-by: "jan p. springer" Cc: stable@vger.kernel.org Signed-off-by: Stanislaw Gruszka Signed-off-by: John W. Linville --- net/mac80211/agg-rx.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/net/mac80211/agg-rx.c b/net/mac80211/agg-rx.c index 1068f668ac4e..64d3ce5ea1a0 100644 --- a/net/mac80211/agg-rx.c +++ b/net/mac80211/agg-rx.c @@ -49,6 +49,8 @@ static void ieee80211_free_tid_rx(struct rcu_head *h) container_of(h, struct tid_ampdu_rx, rcu_head); int i; + del_timer_sync(&tid_rx->reorder_timer); + for (i = 0; i < tid_rx->buf_size; i++) dev_kfree_skb(tid_rx->reorder_buf[i]); kfree(tid_rx->reorder_buf); @@ -91,7 +93,6 @@ void ___ieee80211_stop_rx_ba_session(struct sta_info *sta, u16 tid, tid, WLAN_BACK_RECIPIENT, reason); del_timer_sync(&tid_rx->session_timer); - del_timer_sync(&tid_rx->reorder_timer); call_rcu(&tid_rx->rcu_head, ieee80211_free_tid_rx); } -- cgit v1.2.3 From 46470e5bb03c5aa685160dbaa45c013fb3997788 Mon Sep 17 00:00:00 2001 From: Bob Copeland Date: Tue, 20 Mar 2012 10:48:40 -0400 Subject: ath5k: drop self from MAINTAINERS I simply don't have any hobby hacking time after family time and non-kernel-related job time, so I resume status as part-time mailing list lurker. Signed-off-by: Bob Copeland Signed-off-by: John W. Linville --- MAINTAINERS | 1 - 1 file changed, 1 deletion(-) diff --git a/MAINTAINERS b/MAINTAINERS index 92f9924c4335..0ddc77fe46b6 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -1247,7 +1247,6 @@ ATHEROS ATH5K WIRELESS DRIVER M: Jiri Slaby M: Nick Kossifidis M: "Luis R. Rodriguez" -M: Bob Copeland L: linux-wireless@vger.kernel.org L: ath5k-devel@lists.ath5k.org W: http://wireless.kernel.org/en/users/Drivers/ath5k -- cgit v1.2.3 From 643c61e119459e9d750087b7b34be94491efebf9 Mon Sep 17 00:00:00 2001 From: Larry Finger Date: Mon, 26 Mar 2012 09:59:48 -0500 Subject: rtlwifi: rtl8192ce: rtl8192cu: rtl8192de: Fix low-gain setting when scanning In https://bugzilla.redhat.com/show_bug.cgi?id=770207, slowdowns of driver rtl8192ce are reported. One fix (commit a9b89e2) has already been applied, and it helped, but the maximum RX speed would still drop to 1 Mbps. As in the previous fix, the initial gain was determined to be the problem; however, the problem arises from a setting of the gain when scans are started. Driver rtl8192de also has the same code structure - this one is fixed as well. Reported-and-Tested-by: Ivan Pesin Signed-off-by: Larry Finger Cc: Stable Signed-off-by: John W. Linville --- drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c | 2 +- drivers/net/wireless/rtlwifi/rtl8192de/phy.c | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c b/drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c index 1eec3a06d1f3..4c016241f340 100644 --- a/drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c +++ b/drivers/net/wireless/rtlwifi/rtl8192c/phy_common.c @@ -1893,7 +1893,7 @@ void rtl92c_phy_set_io(struct ieee80211_hw *hw) break; case IO_CMD_PAUSE_DM_BY_SCAN: rtlphy->initgain_backup.xaagccore1 = dm_digtable.cur_igvalue; - dm_digtable.cur_igvalue = 0x17; + dm_digtable.cur_igvalue = 0x37; rtl92c_dm_write_dig(hw); break; default: diff --git a/drivers/net/wireless/rtlwifi/rtl8192de/phy.c b/drivers/net/wireless/rtlwifi/rtl8192de/phy.c index 34591eeb8376..28fc5fb8057b 100644 --- a/drivers/net/wireless/rtlwifi/rtl8192de/phy.c +++ b/drivers/net/wireless/rtlwifi/rtl8192de/phy.c @@ -3077,7 +3077,7 @@ static void rtl92d_phy_set_io(struct ieee80211_hw *hw) break; case IO_CMD_PAUSE_DM_BY_SCAN: rtlphy->initgain_backup.xaagccore1 = de_digtable.cur_igvalue; - de_digtable.cur_igvalue = 0x17; + de_digtable.cur_igvalue = 0x37; rtl92d_dm_write_dig(hw); break; default: -- cgit v1.2.3 From 52f5509fe8ccb607ff9b84ad618f244262336475 Mon Sep 17 00:00:00 2001 From: Jiri Pirko Date: Tue, 20 Mar 2012 18:10:01 +0000 Subject: e1000: fix vlan processing regression This patch fixes a regression introduced by commit "e1000: do vlan cleanup (799d531)". Apparently some e1000 chips (not mine) are sensitive about the order of setting vlan filter and vlan stripping/inserting functionality. So this patch changes the order so it's the same as before vlan cleanup. Reported-by: Ben Greear Signed-off-by: Jiri Pirko Tested-by: Ben Greear Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000/e1000_main.c | 35 +++++++++++++++++---------- 1 file changed, 22 insertions(+), 13 deletions(-) diff --git a/drivers/net/ethernet/intel/e1000/e1000_main.c b/drivers/net/ethernet/intel/e1000/e1000_main.c index 0e9aec8f6917..bcba9cfe3d03 100644 --- a/drivers/net/ethernet/intel/e1000/e1000_main.c +++ b/drivers/net/ethernet/intel/e1000/e1000_main.c @@ -164,6 +164,8 @@ static int e1000_82547_fifo_workaround(struct e1000_adapter *adapter, static bool e1000_vlan_used(struct e1000_adapter *adapter); static void e1000_vlan_mode(struct net_device *netdev, netdev_features_t features); +static void e1000_vlan_filter_on_off(struct e1000_adapter *adapter, + bool filter_on); static int e1000_vlan_rx_add_vid(struct net_device *netdev, u16 vid); static int e1000_vlan_rx_kill_vid(struct net_device *netdev, u16 vid); static void e1000_restore_vlan(struct e1000_adapter *adapter); @@ -1214,7 +1216,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev, if (err) goto err_register; - e1000_vlan_mode(netdev, netdev->features); + e1000_vlan_filter_on_off(adapter, false); /* print bus type/speed/width info */ e_info(probe, "(PCI%s:%dMHz:%d-bit) %pM\n", @@ -4770,6 +4772,22 @@ static bool e1000_vlan_used(struct e1000_adapter *adapter) return false; } +static void __e1000_vlan_mode(struct e1000_adapter *adapter, + netdev_features_t features) +{ + struct e1000_hw *hw = &adapter->hw; + u32 ctrl; + + ctrl = er32(CTRL); + if (features & NETIF_F_HW_VLAN_RX) { + /* enable VLAN tag insert/strip */ + ctrl |= E1000_CTRL_VME; + } else { + /* disable VLAN tag insert/strip */ + ctrl &= ~E1000_CTRL_VME; + } + ew32(CTRL, ctrl); +} static void e1000_vlan_filter_on_off(struct e1000_adapter *adapter, bool filter_on) { @@ -4779,6 +4797,7 @@ static void e1000_vlan_filter_on_off(struct e1000_adapter *adapter, if (!test_bit(__E1000_DOWN, &adapter->flags)) e1000_irq_disable(adapter); + __e1000_vlan_mode(adapter, adapter->netdev->features); if (filter_on) { /* enable VLAN receive filtering */ rctl = er32(RCTL); @@ -4799,24 +4818,14 @@ static void e1000_vlan_filter_on_off(struct e1000_adapter *adapter, } static void e1000_vlan_mode(struct net_device *netdev, - netdev_features_t features) + netdev_features_t features) { struct e1000_adapter *adapter = netdev_priv(netdev); - struct e1000_hw *hw = &adapter->hw; - u32 ctrl; if (!test_bit(__E1000_DOWN, &adapter->flags)) e1000_irq_disable(adapter); - ctrl = er32(CTRL); - if (features & NETIF_F_HW_VLAN_RX) { - /* enable VLAN tag insert/strip */ - ctrl |= E1000_CTRL_VME; - } else { - /* disable VLAN tag insert/strip */ - ctrl &= ~E1000_CTRL_VME; - } - ew32(CTRL, ctrl); + __e1000_vlan_mode(adapter, features); if (!test_bit(__E1000_DOWN, &adapter->flags)) e1000_irq_enable(adapter); -- cgit v1.2.3 From 4eee6a3a04e8bb53fbe7de0f64d0524d3fbe3f80 Mon Sep 17 00:00:00 2001 From: Phil Sutter Date: Mon, 26 Mar 2012 09:01:30 +0000 Subject: wimax: i2400m - prevent a possible kernel bug due to missing fw_name string This happened on a machine with a custom hotplug script calling nameif, probably due to slow firmware loading. At the time nameif uses ethtool to gather interface information, i2400m->fw_name is zero and so a null pointer dereference occurs from within i2400m_get_drvinfo(). Signed-off-by: Phil Sutter Signed-off-by: David S. Miller --- drivers/net/wimax/i2400m/netdev.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-) diff --git a/drivers/net/wimax/i2400m/netdev.c b/drivers/net/wimax/i2400m/netdev.c index 63e4b709efa9..1d76ae855f07 100644 --- a/drivers/net/wimax/i2400m/netdev.c +++ b/drivers/net/wimax/i2400m/netdev.c @@ -597,7 +597,8 @@ static void i2400m_get_drvinfo(struct net_device *net_dev, struct i2400m *i2400m = net_dev_to_i2400m(net_dev); strncpy(info->driver, KBUILD_MODNAME, sizeof(info->driver) - 1); - strncpy(info->fw_version, i2400m->fw_name, sizeof(info->fw_version) - 1); + strncpy(info->fw_version, + i2400m->fw_name ? : "", sizeof(info->fw_version) - 1); if (net_dev->dev.parent) strncpy(info->bus_info, dev_name(net_dev->dev.parent), sizeof(info->bus_info) - 1); -- cgit v1.2.3 From b7440892802be38e6eeb0a17897deeb85476eff4 Mon Sep 17 00:00:00 2001 From: Phil Sutter Date: Mon, 26 Mar 2012 09:01:31 +0000 Subject: wimax: i2400m-usb - use a private struct ethtool_ops This way the USB variant of the driver uses usb_make_path in order to provide bus-info compatible to other USB drivers (like e.g. asix.c). Signed-off-by: Phil Sutter Signed-off-by: David S. Miller --- drivers/net/wimax/i2400m/usb.c | 18 ++++++++++++++++++ 1 file changed, 18 insertions(+) diff --git a/drivers/net/wimax/i2400m/usb.c b/drivers/net/wimax/i2400m/usb.c index 2c1b8b687646..29b1e033a10b 100644 --- a/drivers/net/wimax/i2400m/usb.c +++ b/drivers/net/wimax/i2400m/usb.c @@ -339,6 +339,23 @@ int i2400mu_bus_reset(struct i2400m *i2400m, enum i2400m_reset_type rt) return result; } +static void i2400mu_get_drvinfo(struct net_device *net_dev, + struct ethtool_drvinfo *info) +{ + struct i2400m *i2400m = net_dev_to_i2400m(net_dev); + struct i2400mu *i2400mu = container_of(i2400m, struct i2400mu, i2400m); + struct usb_device *udev = i2400mu->usb_dev; + + strncpy(info->driver, KBUILD_MODNAME, sizeof(info->driver) - 1); + strncpy(info->fw_version, + i2400m->fw_name ? : "", sizeof(info->fw_version) - 1); + usb_make_path(udev, info->bus_info, sizeof(info->bus_info)); +} + +static const struct ethtool_ops i2400mu_ethtool_ops = { + .get_drvinfo = i2400mu_get_drvinfo, + .get_link = ethtool_op_get_link, +}; static void i2400mu_netdev_setup(struct net_device *net_dev) @@ -347,6 +364,7 @@ void i2400mu_netdev_setup(struct net_device *net_dev) struct i2400mu *i2400mu = container_of(i2400m, struct i2400mu, i2400m); i2400mu_init(i2400mu); i2400m_netdev_setup(net_dev); + net_dev->ethtool_ops = &i2400mu_ethtool_ops; } -- cgit v1.2.3 From f0e81fecd4f83de7854262c8a6b3af19dfa99bf9 Mon Sep 17 00:00:00 2001 From: Nobuhiro Iwamatsu Date: Sun, 25 Mar 2012 18:59:51 +0000 Subject: net: sh_eth: Add support SH7734 Add define of SH7734 register and sh_eth_reset_hw_crc function. V3: Rebase net/HEAD. V2: Do not split line of #if defined. Signed-off-by: Nobuhiro Iwamatsu Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/Kconfig | 5 +++-- drivers/net/ethernet/renesas/sh_eth.c | 20 +++++++++++++++++--- drivers/net/ethernet/renesas/sh_eth.h | 11 ++++++++--- 3 files changed, 28 insertions(+), 8 deletions(-) diff --git a/drivers/net/ethernet/renesas/Kconfig b/drivers/net/ethernet/renesas/Kconfig index 9755b49bbefb..3fb2355af37e 100644 --- a/drivers/net/ethernet/renesas/Kconfig +++ b/drivers/net/ethernet/renesas/Kconfig @@ -7,7 +7,8 @@ config SH_ETH depends on SUPERH && \ (CPU_SUBTYPE_SH7710 || CPU_SUBTYPE_SH7712 || \ CPU_SUBTYPE_SH7763 || CPU_SUBTYPE_SH7619 || \ - CPU_SUBTYPE_SH7724 || CPU_SUBTYPE_SH7757) + CPU_SUBTYPE_SH7724 || CPU_SUBTYPE_SH7734 || \ + CPU_SUBTYPE_SH7757) select CRC32 select NET_CORE select MII @@ -16,4 +17,4 @@ config SH_ETH ---help--- Renesas SuperH Ethernet device driver. This driver supporting CPUs are: - - SH7710, SH7712, SH7763, SH7619, SH7724, and SH7757. + - SH7619, SH7710, SH7712, SH7724, SH7734, SH7763 and SH7757. diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 8615961c1287..8bdf070ace90 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -1,8 +1,8 @@ /* * SuperH Ethernet device driver * - * Copyright (C) 2006-2008 Nobuhiro Iwamatsu - * Copyright (C) 2008-2009 Renesas Solutions Corp. + * Copyright (C) 2006-2012 Nobuhiro Iwamatsu + * Copyright (C) 2008-2012 Renesas Solutions Corp. * * This program is free software; you can redistribute it and/or modify it * under the terms and conditions of the GNU General Public License, @@ -38,6 +38,7 @@ #include #include #include +#include #include #include "sh_eth.h" @@ -279,8 +280,9 @@ static struct sh_eth_cpu_data *sh_eth_get_cpu_data(struct sh_eth_private *mdp) return &sh_eth_my_cpu_data; } -#elif defined(CONFIG_CPU_SUBTYPE_SH7763) +#elif defined(CONFIG_CPU_SUBTYPE_SH7734) || defined(CONFIG_CPU_SUBTYPE_SH7763) #define SH_ETH_HAS_TSU 1 +static void sh_eth_reset_hw_crc(struct net_device *ndev); static void sh_eth_chip_reset(struct net_device *ndev) { struct sh_eth_private *mdp = netdev_priv(ndev); @@ -314,6 +316,9 @@ static void sh_eth_reset(struct net_device *ndev) sh_eth_write(ndev, 0x0, RDFAR); sh_eth_write(ndev, 0x0, RDFXR); sh_eth_write(ndev, 0x0, RDFFR); + + /* Reset HW CRC register */ + sh_eth_reset_hw_crc(ndev); } static void sh_eth_set_duplex(struct net_device *ndev) @@ -370,8 +375,17 @@ static struct sh_eth_cpu_data sh_eth_my_cpu_data = { .no_trimd = 1, .no_ade = 1, .tsu = 1, +#if defined(CONFIG_CPU_SUBTYPE_SH7734) + .hw_crc = 1, +#endif }; +static void sh_eth_reset_hw_crc(struct net_device *ndev) +{ + if (sh_eth_my_cpu_data.hw_crc) + sh_eth_write(ndev, 0x0, CSMR); +} + #elif defined(CONFIG_CPU_SUBTYPE_SH7619) #define SH_ETH_RESET_DEFAULT 1 static struct sh_eth_cpu_data sh_eth_my_cpu_data = { diff --git a/drivers/net/ethernet/renesas/sh_eth.h b/drivers/net/ethernet/renesas/sh_eth.h index 57dc26261116..e66de1823532 100644 --- a/drivers/net/ethernet/renesas/sh_eth.h +++ b/drivers/net/ethernet/renesas/sh_eth.h @@ -1,8 +1,8 @@ /* * SuperH Ethernet device driver * - * Copyright (C) 2006-2008 Nobuhiro Iwamatsu - * Copyright (C) 2008-2011 Renesas Solutions Corp. + * Copyright (C) 2006-2012 Nobuhiro Iwamatsu + * Copyright (C) 2008-2012 Renesas Solutions Corp. * * This program is free software; you can redistribute it and/or modify it * under the terms and conditions of the GNU General Public License, @@ -98,6 +98,8 @@ enum { CEECR, MAFCR, RTRATE, + CSMR, + RMII_MII, /* TSU Absolute address */ ARSTR, @@ -172,6 +174,7 @@ static const u16 sh_eth_offset_gigabit[SH_ETH_MAX_REGISTER_OFFSET] = { [RMCR] = 0x0458, [RPADIR] = 0x0460, [FCFTR] = 0x0468, + [CSMR] = 0x04E4, [ECMR] = 0x0500, [ECSR] = 0x0510, @@ -200,6 +203,7 @@ static const u16 sh_eth_offset_gigabit[SH_ETH_MAX_REGISTER_OFFSET] = { [CERCR] = 0x0768, [CEECR] = 0x0770, [MAFCR] = 0x0778, + [RMII_MII] = 0x0790, [ARSTR] = 0x0000, [TSU_CTRST] = 0x0004, @@ -377,7 +381,7 @@ static const u16 sh_eth_offset_fast_sh3_sh2[SH_ETH_MAX_REGISTER_OFFSET] = { /* * Register's bits */ -#ifdef CONFIG_CPU_SUBTYPE_SH7763 +#if defined(CONFIG_CPU_SUBTYPE_SH7734) || defined(CONFIG_CPU_SUBTYPE_SH7763) /* EDSR */ enum EDSR_BIT { EDSR_ENT = 0x01, EDSR_ENR = 0x02, @@ -751,6 +755,7 @@ struct sh_eth_cpu_data { unsigned rpadir:1; /* E-DMAC have RPADIR */ unsigned no_trimd:1; /* E-DMAC DO NOT have TRIMD */ unsigned no_ade:1; /* E-DMAC DO NOT have ADE bit in EESR */ + unsigned hw_crc:1; /* E-DMAC have CSMR */ }; struct sh_eth_private { -- cgit v1.2.3 From a2daf263107ba3eb6db33931881731fa51c95045 Mon Sep 17 00:00:00 2001 From: Guan Xin Date: Mon, 26 Mar 2012 04:11:46 +0000 Subject: USB: Add Motorola Rokr E6 Id to the USBNet driver "zaurus" Added Vendor/Device Id of Motorola Rokr E6 (22b8:6027) so it can be recognized by the "zaurus" USBNet driver. Applies to Linux 3.2.13 and 2.6.39.4. Signed-off-by: Guan Xin Signed-off-by: David S. Miller --- drivers/net/usb/zaurus.c | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/drivers/net/usb/zaurus.c b/drivers/net/usb/zaurus.c index c3197ce0e2ad..34db195fb8b0 100644 --- a/drivers/net/usb/zaurus.c +++ b/drivers/net/usb/zaurus.c @@ -337,6 +337,11 @@ static const struct usb_device_id products [] = { .driver_info = ZAURUS_PXA_INFO, }, { + /* Motorola Rokr E6 */ + USB_DEVICE_AND_INTERFACE_INFO(0x22b8, 0x6027, USB_CLASS_COMM, + USB_CDC_SUBCLASS_MDLM, USB_CDC_PROTO_NONE), + .driver_info = (unsigned long) &bogus_mdlm_info, +}, { /* Motorola MOTOMAGX phones */ USB_DEVICE_AND_INTERFACE_INFO(0x22b8, 0x6425, USB_CLASS_COMM, USB_CDC_SUBCLASS_MDLM, USB_CDC_PROTO_NONE), -- cgit v1.2.3 From 452427b015b1b0cbbef7b6207908726837d39d57 Mon Sep 17 00:00:00 2001 From: Yuval Mintz Date: Mon, 26 Mar 2012 20:47:07 +0000 Subject: bnx2x: previous driver unload revised The flow in which the bnx2x driver starts after a previous driver has been terminated in an 'unclean' manner has several bugs and FW risks, which makes it possible for the driver to fail after boot-from-SAN or kdump. This patch contains a revised flow which performs a safer initialization, solving the possible crash scenarios. Notice this patch contains lines with over 80 characters, as it keeps print-strings in a single line. Signed-off-by: Yuval Mintz Signed-off-by: Eilon Greenstein Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2x/bnx2x.h | 7 + drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c | 40 +- drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h | 3 + drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h | 3 + drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c | 1 - drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h | 2 + drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c | 464 ++++++++++++++++++----- drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h | 4 + 8 files changed, 417 insertions(+), 107 deletions(-) diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h index e37161f19250..2c9ee552dffc 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x.h @@ -1173,6 +1173,13 @@ enum { }; +struct bnx2x_prev_path_list { + u8 bus; + u8 slot; + u8 path; + struct list_head list; +}; + struct bnx2x { /* Fields used in the tx and intr/napi performance paths * are grouped together in the beginning of the structure diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c index f1f3ca65667a..44556b719e81 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c @@ -1721,6 +1721,29 @@ static void bnx2x_squeeze_objects(struct bnx2x *bp) } while (0) #endif +bool bnx2x_test_firmware_version(struct bnx2x *bp, bool is_err) +{ + /* build FW version dword */ + u32 my_fw = (BCM_5710_FW_MAJOR_VERSION) + + (BCM_5710_FW_MINOR_VERSION << 8) + + (BCM_5710_FW_REVISION_VERSION << 16) + + (BCM_5710_FW_ENGINEERING_VERSION << 24); + + /* read loaded FW from chip */ + u32 loaded_fw = REG_RD(bp, XSEM_REG_PRAM); + + DP(NETIF_MSG_IFUP, "loaded fw %x, my fw %x\n", loaded_fw, my_fw); + + if (loaded_fw != my_fw) { + if (is_err) + BNX2X_ERR("bnx2x with FW %x was already loaded, which mismatches my %x FW. aborting\n", + loaded_fw, my_fw); + return false; + } + + return true; +} + /* must be called with rtnl_lock */ int bnx2x_nic_load(struct bnx2x *bp, int load_mode) { @@ -1815,23 +1838,8 @@ int bnx2x_nic_load(struct bnx2x *bp, int load_mode) } if (load_code != FW_MSG_CODE_DRV_LOAD_COMMON_CHIP && load_code != FW_MSG_CODE_DRV_LOAD_COMMON) { - /* build FW version dword */ - u32 my_fw = (BCM_5710_FW_MAJOR_VERSION) + - (BCM_5710_FW_MINOR_VERSION << 8) + - (BCM_5710_FW_REVISION_VERSION << 16) + - (BCM_5710_FW_ENGINEERING_VERSION << 24); - - /* read loaded FW from chip */ - u32 loaded_fw = REG_RD(bp, XSEM_REG_PRAM); - - DP(BNX2X_MSG_SP, "loaded fw %x, my fw %x", - loaded_fw, my_fw); - /* abort nic load if version mismatch */ - if (my_fw != loaded_fw) { - BNX2X_ERR("bnx2x with FW %x already loaded, " - "which mismatches my %x FW. aborting", - loaded_fw, my_fw); + if (!bnx2x_test_firmware_version(bp, true)) { rc = -EBUSY; LOAD_ERROR_EXIT(bp, load_error2); } diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h index 8b163388659a..5c27454d2ec2 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h @@ -431,6 +431,9 @@ void bnx2x_panic_dump(struct bnx2x *bp); void bnx2x_fw_dump_lvl(struct bnx2x *bp, const char *lvl); +/* validate currect fw is loaded */ +bool bnx2x_test_firmware_version(struct bnx2x *bp, bool is_err); + /* dev_close main block */ int bnx2x_nic_unload(struct bnx2x *bp, int unload_mode); diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h index 5d71b7d43237..dbff5915b81a 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_hsi.h @@ -1251,6 +1251,9 @@ struct drv_func_mb { #define DRV_MSG_CODE_LINK_STATUS_CHANGED 0x01000000 + #define DRV_MSG_CODE_INITIATE_FLR 0x02000000 + #define REQ_BC_VER_4_INITIATE_FLR 0x00070213 + #define BIOS_MSG_CODE_LIC_CHALLENGE 0xff010000 #define BIOS_MSG_CODE_LIC_RESPONSE 0xff020000 #define BIOS_MSG_CODE_VIRT_MAC_PRIM 0xff030000 diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c index beb4cdbdb6e1..efa557b76ac7 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c @@ -35,7 +35,6 @@ #define ETH_MAX_PACKET_SIZE 1500 #define ETH_MAX_JUMBO_PACKET_SIZE 9600 #define MDIO_ACCESS_TIMEOUT 1000 -#define BMAC_CONTROL_RX_ENABLE 2 #define WC_LANE_MAX 4 #define I2C_SWITCH_WIDTH 2 #define I2C_BSC0 0 diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h index 7ba557a610da..763535ee4832 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.h @@ -89,6 +89,8 @@ #define PFC_BRB_FULL_LB_XON_THRESHOLD 250 #define MAXVAL(a, b) (((a) > (b)) ? (a) : (b)) + +#define BMAC_CONTROL_RX_ENABLE 2 /***********************************************************/ /* Structs */ /***********************************************************/ diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c index f7f9aa807264..e077d2508727 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c @@ -52,6 +52,7 @@ #include #include #include +#include #include #include @@ -211,6 +212,10 @@ static DEFINE_PCI_DEVICE_TABLE(bnx2x_pci_tbl) = { MODULE_DEVICE_TABLE(pci, bnx2x_pci_tbl); +/* Global resources for unloading a previously loaded device */ +#define BNX2X_PREV_WAIT_NEEDED 1 +static DEFINE_SEMAPHORE(bnx2x_prev_sem); +static LIST_HEAD(bnx2x_prev_list); /**************************************************************************** * General service functions ****************************************************************************/ @@ -8812,109 +8817,371 @@ static inline void bnx2x_undi_int_disable(struct bnx2x *bp) bnx2x_undi_int_disable_e1h(bp); } -static void __devinit bnx2x_undi_unload(struct bnx2x *bp) +static void __devinit bnx2x_prev_unload_close_mac(struct bnx2x *bp) { - u32 val; + u32 val, base_addr, offset, mask, reset_reg; + bool mac_stopped = false; + u8 port = BP_PORT(bp); - /* possibly another driver is trying to reset the chip */ - bnx2x_acquire_hw_lock(bp, HW_LOCK_RESOURCE_RESET); + reset_reg = REG_RD(bp, MISC_REG_RESET_REG_2); - /* check if doorbell queue is reset */ - if (REG_RD(bp, GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET) - & MISC_REGISTERS_RESET_REG_1_RST_DORQ) { + if (!CHIP_IS_E3(bp)) { + val = REG_RD(bp, NIG_REG_BMAC0_REGS_OUT_EN + port * 4); + mask = MISC_REGISTERS_RESET_REG_2_RST_BMAC0 << port; + if ((mask & reset_reg) && val) { + u32 wb_data[2]; + BNX2X_DEV_INFO("Disable bmac Rx\n"); + base_addr = BP_PORT(bp) ? NIG_REG_INGRESS_BMAC1_MEM + : NIG_REG_INGRESS_BMAC0_MEM; + offset = CHIP_IS_E2(bp) ? BIGMAC2_REGISTER_BMAC_CONTROL + : BIGMAC_REGISTER_BMAC_CONTROL; - /* - * Check if it is the UNDI driver + /* + * use rd/wr since we cannot use dmae. This is safe + * since MCP won't access the bus due to the request + * to unload, and no function on the path can be + * loaded at this time. + */ + wb_data[0] = REG_RD(bp, base_addr + offset); + wb_data[1] = REG_RD(bp, base_addr + offset + 0x4); + wb_data[0] &= ~BMAC_CONTROL_RX_ENABLE; + REG_WR(bp, base_addr + offset, wb_data[0]); + REG_WR(bp, base_addr + offset + 0x4, wb_data[1]); + + } + BNX2X_DEV_INFO("Disable emac Rx\n"); + REG_WR(bp, NIG_REG_NIG_EMAC0_EN + BP_PORT(bp)*4, 0); + + mac_stopped = true; + } else { + if (reset_reg & MISC_REGISTERS_RESET_REG_2_XMAC) { + BNX2X_DEV_INFO("Disable xmac Rx\n"); + base_addr = BP_PORT(bp) ? GRCBASE_XMAC1 : GRCBASE_XMAC0; + val = REG_RD(bp, base_addr + XMAC_REG_PFC_CTRL_HI); + REG_WR(bp, base_addr + XMAC_REG_PFC_CTRL_HI, + val & ~(1 << 1)); + REG_WR(bp, base_addr + XMAC_REG_PFC_CTRL_HI, + val | (1 << 1)); + REG_WR(bp, base_addr + XMAC_REG_CTRL, 0); + mac_stopped = true; + } + mask = MISC_REGISTERS_RESET_REG_2_UMAC0 << port; + if (mask & reset_reg) { + BNX2X_DEV_INFO("Disable umac Rx\n"); + base_addr = BP_PORT(bp) ? GRCBASE_UMAC1 : GRCBASE_UMAC0; + REG_WR(bp, base_addr + UMAC_REG_COMMAND_CONFIG, 0); + mac_stopped = true; + } + } + + if (mac_stopped) + msleep(20); + +} + +#define BNX2X_PREV_UNDI_PROD_ADDR(p) (BAR_TSTRORM_INTMEM + 0x1508 + ((p) << 4)) +#define BNX2X_PREV_UNDI_RCQ(val) ((val) & 0xffff) +#define BNX2X_PREV_UNDI_BD(val) ((val) >> 16 & 0xffff) +#define BNX2X_PREV_UNDI_PROD(rcq, bd) ((bd) << 16 | (rcq)) + +static void __devinit bnx2x_prev_unload_undi_inc(struct bnx2x *bp, u8 port, + u8 inc) +{ + u16 rcq, bd; + u32 tmp_reg = REG_RD(bp, BNX2X_PREV_UNDI_PROD_ADDR(port)); + + rcq = BNX2X_PREV_UNDI_RCQ(tmp_reg) + inc; + bd = BNX2X_PREV_UNDI_BD(tmp_reg) + inc; + + tmp_reg = BNX2X_PREV_UNDI_PROD(rcq, bd); + REG_WR(bp, BNX2X_PREV_UNDI_PROD_ADDR(port), tmp_reg); + + BNX2X_DEV_INFO("UNDI producer [%d] rings bd -> 0x%04x, rcq -> 0x%04x\n", + port, bd, rcq); +} + +static int __devinit bnx2x_prev_mcp_done(struct bnx2x *bp) +{ + u32 rc = bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE, 0); + if (!rc) { + BNX2X_ERR("MCP response failure, aborting\n"); + return -EBUSY; + } + + return 0; +} + +static bool __devinit bnx2x_prev_is_path_marked(struct bnx2x *bp) +{ + struct bnx2x_prev_path_list *tmp_list; + int rc = false; + + if (down_trylock(&bnx2x_prev_sem)) + return false; + + list_for_each_entry(tmp_list, &bnx2x_prev_list, list) { + if (PCI_SLOT(bp->pdev->devfn) == tmp_list->slot && + bp->pdev->bus->number == tmp_list->bus && + BP_PATH(bp) == tmp_list->path) { + rc = true; + BNX2X_DEV_INFO("Path %d was already cleaned from previous drivers\n", + BP_PATH(bp)); + break; + } + } + + up(&bnx2x_prev_sem); + + return rc; +} + +static int __devinit bnx2x_prev_mark_path(struct bnx2x *bp) +{ + struct bnx2x_prev_path_list *tmp_list; + int rc; + + tmp_list = (struct bnx2x_prev_path_list *) + kmalloc(sizeof(struct bnx2x_prev_path_list), GFP_KERNEL); + if (!tmp_list) { + BNX2X_ERR("Failed to allocate 'bnx2x_prev_path_list'\n"); + return -ENOMEM; + } + + tmp_list->bus = bp->pdev->bus->number; + tmp_list->slot = PCI_SLOT(bp->pdev->devfn); + tmp_list->path = BP_PATH(bp); + + rc = down_interruptible(&bnx2x_prev_sem); + if (rc) { + BNX2X_ERR("Received %d when tried to take lock\n", rc); + kfree(tmp_list); + } else { + BNX2X_DEV_INFO("Marked path [%d] - finished previous unload\n", + BP_PATH(bp)); + list_add(&tmp_list->list, &bnx2x_prev_list); + up(&bnx2x_prev_sem); + } + + return rc; +} + +static bool __devinit bnx2x_can_flr(struct bnx2x *bp) +{ + int pos; + u32 cap; + struct pci_dev *dev = bp->pdev; + + pos = pci_pcie_cap(dev); + if (!pos) + return false; + + pci_read_config_dword(dev, pos + PCI_EXP_DEVCAP, &cap); + if (!(cap & PCI_EXP_DEVCAP_FLR)) + return false; + + return true; +} + +static int __devinit bnx2x_do_flr(struct bnx2x *bp) +{ + int i, pos; + u16 status; + struct pci_dev *dev = bp->pdev; + + /* probe the capability first */ + if (bnx2x_can_flr(bp)) + return -ENOTTY; + + pos = pci_pcie_cap(dev); + if (!pos) + return -ENOTTY; + + /* Wait for Transaction Pending bit clean */ + for (i = 0; i < 4; i++) { + if (i) + msleep((1 << (i - 1)) * 100); + + pci_read_config_word(dev, pos + PCI_EXP_DEVSTA, &status); + if (!(status & PCI_EXP_DEVSTA_TRPND)) + goto clear; + } + + dev_err(&dev->dev, + "transaction is not cleared; proceeding with reset anyway\n"); + +clear: + if (bp->common.bc_ver < REQ_BC_VER_4_INITIATE_FLR) { + BNX2X_ERR("FLR not supported by BC_VER: 0x%x\n", + bp->common.bc_ver); + return -EINVAL; + } + + bnx2x_fw_command(bp, DRV_MSG_CODE_INITIATE_FLR, 0); + + return 0; +} + +static int __devinit bnx2x_prev_unload_uncommon(struct bnx2x *bp) +{ + int rc; + + BNX2X_DEV_INFO("Uncommon unload Flow\n"); + + /* Test if previous unload process was already finished for this path */ + if (bnx2x_prev_is_path_marked(bp)) + return bnx2x_prev_mcp_done(bp); + + /* If function has FLR capabilities, and existing FW version matches + * the one required, then FLR will be sufficient to clean any residue + * left by previous driver + */ + if (bnx2x_test_firmware_version(bp, false) && bnx2x_can_flr(bp)) + return bnx2x_do_flr(bp); + + /* Close the MCP request, return failure*/ + rc = bnx2x_prev_mcp_done(bp); + if (!rc) + rc = BNX2X_PREV_WAIT_NEEDED; + + return rc; +} + +static int __devinit bnx2x_prev_unload_common(struct bnx2x *bp) +{ + u32 reset_reg, tmp_reg = 0, rc; + /* It is possible a previous function received 'common' answer, + * but hasn't loaded yet, therefore creating a scenario of + * multiple functions receiving 'common' on the same path. + */ + BNX2X_DEV_INFO("Common unload Flow\n"); + + if (bnx2x_prev_is_path_marked(bp)) + return bnx2x_prev_mcp_done(bp); + + reset_reg = REG_RD(bp, MISC_REG_RESET_REG_1); + + /* Reset should be performed after BRB is emptied */ + if (reset_reg & MISC_REGISTERS_RESET_REG_1_RST_BRB1) { + u32 timer_count = 1000; + bool prev_undi = false; + + /* Close the MAC Rx to prevent BRB from filling up */ + bnx2x_prev_unload_close_mac(bp); + + /* Check if the UNDI driver was previously loaded * UNDI driver initializes CID offset for normal bell to 0x7 */ - val = REG_RD(bp, DORQ_REG_NORM_CID_OFST); - if (val == 0x7) { - u32 reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; - /* save our pf_num */ - int orig_pf_num = bp->pf_num; - int port; - u32 swap_en, swap_val, value; - - /* clear the UNDI indication */ - REG_WR(bp, DORQ_REG_NORM_CID_OFST, 0); - - BNX2X_DEV_INFO("UNDI is active! reset device\n"); - - /* try unload UNDI on port 0 */ - bp->pf_num = 0; - bp->fw_seq = - (SHMEM_RD(bp, func_mb[bp->pf_num].drv_mb_header) & - DRV_MSG_SEQ_NUMBER_MASK); - reset_code = bnx2x_fw_command(bp, reset_code, 0); - - /* if UNDI is loaded on the other port */ - if (reset_code != FW_MSG_CODE_DRV_UNLOAD_COMMON) { - - /* send "DONE" for previous unload */ - bnx2x_fw_command(bp, - DRV_MSG_CODE_UNLOAD_DONE, 0); - - /* unload UNDI on port 1 */ - bp->pf_num = 1; - bp->fw_seq = - (SHMEM_RD(bp, func_mb[bp->pf_num].drv_mb_header) & - DRV_MSG_SEQ_NUMBER_MASK); - reset_code = DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS; - - bnx2x_fw_command(bp, reset_code, 0); + reset_reg = REG_RD(bp, MISC_REG_RESET_REG_1); + if (reset_reg & MISC_REGISTERS_RESET_REG_1_RST_DORQ) { + tmp_reg = REG_RD(bp, DORQ_REG_NORM_CID_OFST); + if (tmp_reg == 0x7) { + BNX2X_DEV_INFO("UNDI previously loaded\n"); + prev_undi = true; + /* clear the UNDI indication */ + REG_WR(bp, DORQ_REG_NORM_CID_OFST, 0); } + } + /* wait until BRB is empty */ + tmp_reg = REG_RD(bp, BRB1_REG_NUM_OF_FULL_BLOCKS); + while (timer_count) { + u32 prev_brb = tmp_reg; - bnx2x_undi_int_disable(bp); - port = BP_PORT(bp); - - /* close input traffic and wait for it */ - /* Do not rcv packets to BRB */ - REG_WR(bp, (port ? NIG_REG_LLH1_BRB1_DRV_MASK : - NIG_REG_LLH0_BRB1_DRV_MASK), 0x0); - /* Do not direct rcv packets that are not for MCP to - * the BRB */ - REG_WR(bp, (port ? NIG_REG_LLH1_BRB1_NOT_MCP : - NIG_REG_LLH0_BRB1_NOT_MCP), 0x0); - /* clear AEU */ - REG_WR(bp, (port ? MISC_REG_AEU_MASK_ATTN_FUNC_1 : - MISC_REG_AEU_MASK_ATTN_FUNC_0), 0); - msleep(10); - - /* save NIG port swap info */ - swap_val = REG_RD(bp, NIG_REG_PORT_SWAP); - swap_en = REG_RD(bp, NIG_REG_STRAP_OVERRIDE); - /* reset device */ - REG_WR(bp, - GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_CLEAR, - 0xd3ffffff); - - value = 0x1400; - if (CHIP_IS_E3(bp)) { - value |= MISC_REGISTERS_RESET_REG_2_MSTAT0; - value |= MISC_REGISTERS_RESET_REG_2_MSTAT1; - } + tmp_reg = REG_RD(bp, BRB1_REG_NUM_OF_FULL_BLOCKS); + if (!tmp_reg) + break; - REG_WR(bp, - GRCBASE_MISC + MISC_REGISTERS_RESET_REG_2_CLEAR, - value); + BNX2X_DEV_INFO("BRB still has 0x%08x\n", tmp_reg); - /* take the NIG out of reset and restore swap values */ - REG_WR(bp, - GRCBASE_MISC + MISC_REGISTERS_RESET_REG_1_SET, - MISC_REGISTERS_RESET_REG_1_RST_NIG); - REG_WR(bp, NIG_REG_PORT_SWAP, swap_val); - REG_WR(bp, NIG_REG_STRAP_OVERRIDE, swap_en); + /* reset timer as long as BRB actually gets emptied */ + if (prev_brb > tmp_reg) + timer_count = 1000; + else + timer_count--; - /* send unload done to the MCP */ - bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_DONE, 0); + /* If UNDI resides in memory, manually increment it */ + if (prev_undi) + bnx2x_prev_unload_undi_inc(bp, BP_PORT(bp), 1); - /* restore our func and fw_seq */ - bp->pf_num = orig_pf_num; + udelay(10); } + + if (!timer_count) + BNX2X_ERR("Failed to empty BRB, hope for the best\n"); + } - /* now it's safe to release the lock */ - bnx2x_release_hw_lock(bp, HW_LOCK_RESOURCE_RESET); + /* No packets are in the pipeline, path is ready for reset */ + bnx2x_reset_common(bp); + + rc = bnx2x_prev_mark_path(bp); + if (rc) { + bnx2x_prev_mcp_done(bp); + return rc; + } + + return bnx2x_prev_mcp_done(bp); +} + +static int __devinit bnx2x_prev_unload(struct bnx2x *bp) +{ + int time_counter = 10; + u32 rc, fw, hw_lock_reg, hw_lock_val; + BNX2X_DEV_INFO("Entering Previous Unload Flow\n"); + + /* Release previously held locks */ + hw_lock_reg = (BP_FUNC(bp) <= 5) ? + (MISC_REG_DRIVER_CONTROL_1 + BP_FUNC(bp) * 8) : + (MISC_REG_DRIVER_CONTROL_7 + (BP_FUNC(bp) - 6) * 8); + + hw_lock_val = (REG_RD(bp, hw_lock_reg)); + if (hw_lock_val) { + if (hw_lock_val & HW_LOCK_RESOURCE_NVRAM) { + BNX2X_DEV_INFO("Release Previously held NVRAM lock\n"); + REG_WR(bp, MCP_REG_MCPR_NVM_SW_ARB, + (MCPR_NVM_SW_ARB_ARB_REQ_CLR1 << BP_PORT(bp))); + } + + BNX2X_DEV_INFO("Release Previously held hw lock\n"); + REG_WR(bp, hw_lock_reg, 0xffffffff); + } else + BNX2X_DEV_INFO("No need to release hw/nvram locks\n"); + + if (MCPR_ACCESS_LOCK_LOCK & REG_RD(bp, MCP_REG_MCPR_ACCESS_LOCK)) { + BNX2X_DEV_INFO("Release previously held alr\n"); + REG_WR(bp, MCP_REG_MCPR_ACCESS_LOCK, 0); + } + + + do { + /* Lock MCP using an unload request */ + fw = bnx2x_fw_command(bp, DRV_MSG_CODE_UNLOAD_REQ_WOL_DIS, 0); + if (!fw) { + BNX2X_ERR("MCP response failure, aborting\n"); + rc = -EBUSY; + break; + } + + if (fw == FW_MSG_CODE_DRV_UNLOAD_COMMON) { + rc = bnx2x_prev_unload_common(bp); + break; + } + + /* non-common reply from MCP night require looping */ + rc = bnx2x_prev_unload_uncommon(bp); + if (rc != BNX2X_PREV_WAIT_NEEDED) + break; + + msleep(20); + } while (--time_counter); + + if (!time_counter || rc) { + BNX2X_ERR("Failed unloading previous driver, aborting\n"); + rc = -EBUSY; + } + + BNX2X_DEV_INFO("Finished Previous Unload Flow [%d]\n", rc); + + return rc; } static void __devinit bnx2x_get_common_hwinfo(struct bnx2x *bp) @@ -10100,8 +10367,16 @@ static int __devinit bnx2x_init_bp(struct bnx2x *bp) func = BP_FUNC(bp); /* need to reset chip if undi was active */ - if (!BP_NOMCP(bp)) - bnx2x_undi_unload(bp); + if (!BP_NOMCP(bp)) { + /* init fw_seq */ + bp->fw_seq = + SHMEM_RD(bp, func_mb[BP_FW_MB_IDX(bp)].drv_mb_header) & + DRV_MSG_SEQ_NUMBER_MASK; + BNX2X_DEV_INFO("fw_seq 0x%08x\n", bp->fw_seq); + + bnx2x_prev_unload(bp); + } + if (CHIP_REV_IS_FPGA(bp)) dev_err(&bp->pdev->dev, "FPGA detected\n"); @@ -11431,9 +11706,18 @@ static int __init bnx2x_init(void) static void __exit bnx2x_cleanup(void) { + struct list_head *pos, *q; pci_unregister_driver(&bnx2x_pci_driver); destroy_workqueue(bnx2x_wq); + + /* Free globablly allocated resources */ + list_for_each_safe(pos, q, &bnx2x_prev_list) { + struct bnx2x_prev_path_list *tmp = + list_entry(pos, struct bnx2x_prev_path_list, list); + list_del(pos); + kfree(tmp); + } } void bnx2x_notify_link_changed(struct bnx2x *bp) diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h index fd7fb4581849..ab0a250f95fa 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_reg.h @@ -987,6 +987,7 @@ * clear; 1 = set. Data valid only in addresses 0-4. all the rest are zero. */ #define IGU_REG_WRITE_DONE_PENDING 0x130480 #define MCP_A_REG_MCPR_SCRATCH 0x3a0000 +#define MCP_REG_MCPR_ACCESS_LOCK 0x8009c #define MCP_REG_MCPR_CPU_PROGRAM_COUNTER 0x8501c #define MCP_REG_MCPR_GP_INPUTS 0x800c0 #define MCP_REG_MCPR_GP_OENABLE 0x800c8 @@ -1686,6 +1687,7 @@ [10] rst_dbg; [11] rst_misc_core; [12] rst_dbue (UART); [13] Pci_resetmdio_n; [14] rst_emac0_hard_core; [15] rst_emac1_hard_core; 16] rst_pxp_rq_rd_wr; 31:17] reserved */ +#define MISC_REG_RESET_REG_1 0xa580 #define MISC_REG_RESET_REG_2 0xa590 /* [RW 20] 20 bit GRC address where the scratch-pad of the MCP that is shared with the driver resides */ @@ -5606,6 +5608,7 @@ /* [RC 32] Parity register #0 read clear */ #define XSEM_REG_XSEM_PRTY_STS_CLR_0 0x280128 #define XSEM_REG_XSEM_PRTY_STS_CLR_1 0x280138 +#define MCPR_ACCESS_LOCK_LOCK (1L<<31) #define MCPR_NVM_ACCESS_ENABLE_EN (1L<<0) #define MCPR_NVM_ACCESS_ENABLE_WR_EN (1L<<1) #define MCPR_NVM_ADDR_NVM_ADDR_VALUE (0xffffffL<<0) @@ -5732,6 +5735,7 @@ #define MISC_REGISTERS_GPIO_PORT_SHIFT 4 #define MISC_REGISTERS_GPIO_SET_POS 8 #define MISC_REGISTERS_RESET_REG_1_CLEAR 0x588 +#define MISC_REGISTERS_RESET_REG_1_RST_BRB1 (0x1<<0) #define MISC_REGISTERS_RESET_REG_1_RST_DORQ (0x1<<19) #define MISC_REGISTERS_RESET_REG_1_RST_HC (0x1<<29) #define MISC_REGISTERS_RESET_REG_1_RST_NIG (0x1<<7) -- cgit v1.2.3 From c54e9bd38a06babf94fd45e5f1df9a1109e12818 Mon Sep 17 00:00:00 2001 From: Dmitry Kravkov Date: Mon, 26 Mar 2012 21:08:55 +0000 Subject: bnx2x: fix vector traveling while looking for an empty entry MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Fixes the bug that may prevent from mac to be configured, while there is an empty slot for it. Reported-by: Maciej Żenczykowski Signed-off-by: Dmitry Kravkov Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c index 3f52fadee3ed..513573321625 100644 --- a/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c +++ b/drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c @@ -3847,7 +3847,7 @@ static bool bnx2x_credit_pool_get_entry( continue; /* If we've got here we are going to find a free entry */ - for (idx = vec * BNX2X_POOL_VEC_SIZE, i = 0; + for (idx = vec * BIT_VEC64_ELEM_SZ, i = 0; i < BIT_VEC64_ELEM_SZ; idx++, i++) if (BIT_VEC64_TEST_BIT(o->pool_mirror, idx)) { -- cgit v1.2.3 From 819a100846295461bc0f1bfcb8e5ab11c1bc4cdb Mon Sep 17 00:00:00 2001 From: Dan Carpenter Date: Mon, 26 Mar 2012 21:20:48 +0000 Subject: mISDN: array underflow in open_bchannel() There are two channels here. User space starts counting channels at one but in the kernel we start at zero. If the user passes in a zero channel that's invalid and could lead to memory corruption. Signed-off-by: Dan Carpenter Signed-off-by: David S. Miller --- drivers/isdn/hardware/mISDN/avmfritz.c | 2 +- drivers/isdn/hardware/mISDN/hfcpci.c | 2 +- drivers/isdn/hardware/mISDN/hfcsusb.c | 2 +- drivers/isdn/hardware/mISDN/mISDNipac.c | 2 +- drivers/isdn/hardware/mISDN/mISDNisar.c | 2 +- drivers/isdn/hardware/mISDN/netjet.c | 2 +- drivers/isdn/hardware/mISDN/w6692.c | 2 +- 7 files changed, 7 insertions(+), 7 deletions(-) diff --git a/drivers/isdn/hardware/mISDN/avmfritz.c b/drivers/isdn/hardware/mISDN/avmfritz.c index 05ed4d0cb18b..c0b8c960ee3f 100644 --- a/drivers/isdn/hardware/mISDN/avmfritz.c +++ b/drivers/isdn/hardware/mISDN/avmfritz.c @@ -891,7 +891,7 @@ open_bchannel(struct fritzcard *fc, struct channel_req *rq) { struct bchannel *bch; - if (rq->adr.channel > 2) + if (rq->adr.channel == 0 || rq->adr.channel > 2) return -EINVAL; if (rq->protocol == ISDN_P_NONE) return -EINVAL; diff --git a/drivers/isdn/hardware/mISDN/hfcpci.c b/drivers/isdn/hardware/mISDN/hfcpci.c index d055ae7fa040..e2c83a2d7691 100644 --- a/drivers/isdn/hardware/mISDN/hfcpci.c +++ b/drivers/isdn/hardware/mISDN/hfcpci.c @@ -1962,7 +1962,7 @@ open_bchannel(struct hfc_pci *hc, struct channel_req *rq) { struct bchannel *bch; - if (rq->adr.channel > 2) + if (rq->adr.channel == 0 || rq->adr.channel > 2) return -EINVAL; if (rq->protocol == ISDN_P_NONE) return -EINVAL; diff --git a/drivers/isdn/hardware/mISDN/hfcsusb.c b/drivers/isdn/hardware/mISDN/hfcsusb.c index 602338734634..8cde2a0538ab 100644 --- a/drivers/isdn/hardware/mISDN/hfcsusb.c +++ b/drivers/isdn/hardware/mISDN/hfcsusb.c @@ -486,7 +486,7 @@ open_bchannel(struct hfcsusb *hw, struct channel_req *rq) { struct bchannel *bch; - if (rq->adr.channel > 2) + if (rq->adr.channel == 0 || rq->adr.channel > 2) return -EINVAL; if (rq->protocol == ISDN_P_NONE) return -EINVAL; diff --git a/drivers/isdn/hardware/mISDN/mISDNipac.c b/drivers/isdn/hardware/mISDN/mISDNipac.c index b47e9bed2185..884369f09cad 100644 --- a/drivers/isdn/hardware/mISDN/mISDNipac.c +++ b/drivers/isdn/hardware/mISDN/mISDNipac.c @@ -1506,7 +1506,7 @@ open_bchannel(struct ipac_hw *ipac, struct channel_req *rq) { struct bchannel *bch; - if (rq->adr.channel > 2) + if (rq->adr.channel == 0 || rq->adr.channel > 2) return -EINVAL; if (rq->protocol == ISDN_P_NONE) return -EINVAL; diff --git a/drivers/isdn/hardware/mISDN/mISDNisar.c b/drivers/isdn/hardware/mISDN/mISDNisar.c index 10446ab404b5..9a6da6edcfa8 100644 --- a/drivers/isdn/hardware/mISDN/mISDNisar.c +++ b/drivers/isdn/hardware/mISDN/mISDNisar.c @@ -1670,7 +1670,7 @@ isar_open(struct isar_hw *isar, struct channel_req *rq) { struct bchannel *bch; - if (rq->adr.channel > 2) + if (rq->adr.channel == 0 || rq->adr.channel > 2) return -EINVAL; if (rq->protocol == ISDN_P_NONE) return -EINVAL; diff --git a/drivers/isdn/hardware/mISDN/netjet.c b/drivers/isdn/hardware/mISDN/netjet.c index dd6de9f7a8a3..c726e09d0981 100644 --- a/drivers/isdn/hardware/mISDN/netjet.c +++ b/drivers/isdn/hardware/mISDN/netjet.c @@ -860,7 +860,7 @@ open_bchannel(struct tiger_hw *card, struct channel_req *rq) { struct bchannel *bch; - if (rq->adr.channel > 2) + if (rq->adr.channel == 0 || rq->adr.channel > 2) return -EINVAL; if (rq->protocol == ISDN_P_NONE) return -EINVAL; diff --git a/drivers/isdn/hardware/mISDN/w6692.c b/drivers/isdn/hardware/mISDN/w6692.c index 7f1e7ba75cd1..2183357f0799 100644 --- a/drivers/isdn/hardware/mISDN/w6692.c +++ b/drivers/isdn/hardware/mISDN/w6692.c @@ -1015,7 +1015,7 @@ open_bchannel(struct w6692_hw *card, struct channel_req *rq) { struct bchannel *bch; - if (rq->adr.channel > 2) + if (rq->adr.channel == 0 || rq->adr.channel > 2) return -EINVAL; if (rq->protocol == ISDN_P_NONE) return -EINVAL; -- cgit v1.2.3 From 09e79d6ea65d66e0a5e9ba76865320e74832dc7c Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Mon, 26 Mar 2012 22:52:00 +0000 Subject: eql: dont rely on HZ=100 HZ is more likely to be 1000 these days. timer handlers are run from softirq, no need to disable bh skb priority 1 is TC_PRIO_FILLER Signed-off-by: Eric Dumazet Signed-off-by: David S. Miller --- drivers/net/eql.c | 7 ++++--- include/linux/if_eql.h | 2 +- 2 files changed, 5 insertions(+), 4 deletions(-) diff --git a/drivers/net/eql.c b/drivers/net/eql.c index a59cf961a436..f219d38acf58 100644 --- a/drivers/net/eql.c +++ b/drivers/net/eql.c @@ -125,6 +125,7 @@ #include #include #include +#include #include @@ -143,7 +144,7 @@ static void eql_timer(unsigned long param) equalizer_t *eql = (equalizer_t *) param; struct list_head *this, *tmp, *head; - spin_lock_bh(&eql->queue.lock); + spin_lock(&eql->queue.lock); head = &eql->queue.all_slaves; list_for_each_safe(this, tmp, head) { slave_t *slave = list_entry(this, slave_t, list); @@ -157,7 +158,7 @@ static void eql_timer(unsigned long param) } } - spin_unlock_bh(&eql->queue.lock); + spin_unlock(&eql->queue.lock); eql->timer.expires = jiffies + EQL_DEFAULT_RESCHED_IVAL; add_timer(&eql->timer); @@ -341,7 +342,7 @@ static netdev_tx_t eql_slave_xmit(struct sk_buff *skb, struct net_device *dev) struct net_device *slave_dev = slave->dev; skb->dev = slave_dev; - skb->priority = 1; + skb->priority = TC_PRIO_FILLER; slave->bytes_queued += skb->len; dev_queue_xmit(skb); dev->stats.tx_packets++; diff --git a/include/linux/if_eql.h b/include/linux/if_eql.h index 79c4f268410d..18a5d02a8644 100644 --- a/include/linux/if_eql.h +++ b/include/linux/if_eql.h @@ -22,7 +22,7 @@ #define EQL_DEFAULT_SLAVE_PRIORITY 28800 #define EQL_DEFAULT_MAX_SLAVES 4 #define EQL_DEFAULT_MTU 576 -#define EQL_DEFAULT_RESCHED_IVAL 100 +#define EQL_DEFAULT_RESCHED_IVAL HZ #define EQL_ENSLAVE (SIOCDEVPRIVATE) #define EQL_EMANCIPATE (SIOCDEVPRIVATE + 1) -- cgit v1.2.3 From 21dcda6083a0573686acabca39b3f92ba032d333 Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Tue, 27 Mar 2012 03:04:02 +0000 Subject: f_phonet: fix skb truesize underestimation MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Now skb_add_rx_frag() has a truesize parameter, we can fix f_phonet to properly account truesize of each fragment : a full page. Signed-off-by: Eric Dumazet Cc: Felipe Balbi Cc: Greg Kroah-Hartman Cc: Rémi Denis-Courmont Signed-off-by: David S. Miller --- drivers/usb/gadget/f_phonet.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/usb/gadget/f_phonet.c b/drivers/usb/gadget/f_phonet.c index 85a5cebe96b3..965a6293206a 100644 --- a/drivers/usb/gadget/f_phonet.c +++ b/drivers/usb/gadget/f_phonet.c @@ -345,7 +345,7 @@ static void pn_rx_complete(struct usb_ep *ep, struct usb_request *req) } skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, page, - skb->len <= 1, req->actual, req->actual); + skb->len <= 1, req->actual, PAGE_SIZE); page = NULL; if (req->actual < req->length) { /* Last fragment */ -- cgit v1.2.3 From 094b5855bf37eae4b297bc47bb5bc5454f1f6fab Mon Sep 17 00:00:00 2001 From: Eric Dumazet Date: Tue, 27 Mar 2012 03:17:26 +0000 Subject: cdc-phonet: fix skb truesize underestimation MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit Now skb_add_rx_frag() has a truesize parameter, we can fix cdc-phonet to properly account truesize of each fragment : a full page. Signed-off-by: Eric Dumazet Cc: Felipe Balbi Cc: Greg Kroah-Hartman Cc: Rémi Denis-Courmont Acked-by: Rémi Denis-Courmont Signed-off-by: David S. Miller --- drivers/net/usb/cdc-phonet.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/usb/cdc-phonet.c b/drivers/net/usb/cdc-phonet.c index 3886b30ed373..3e41b00c6806 100644 --- a/drivers/net/usb/cdc-phonet.c +++ b/drivers/net/usb/cdc-phonet.c @@ -165,13 +165,13 @@ static void rx_complete(struct urb *req) memcpy(skb_put(skb, 1), page_address(page), 1); skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, page, 1, req->actual_length, - req->actual_length); + PAGE_SIZE); page = NULL; } } else { skb_add_rx_frag(skb, skb_shinfo(skb)->nr_frags, page, 0, req->actual_length, - req->actual_length); + PAGE_SIZE); page = NULL; } if (req->actual_length < PAGE_SIZE) -- cgit v1.2.3 From b3f4d5990bfc8b060e5010c1464789fca1f4c5b4 Mon Sep 17 00:00:00 2001 From: stephen hemminger Date: Tue, 13 Mar 2012 06:04:20 +0000 Subject: intel: make wired ethernet driver message level consistent (rev2) Dan Carpenter noticed that ixgbevf initial default was different than the rest. But the problem is broader than that, only one Intel driver (ixgb) was doing it almost right. The convention for default debug level should be consistent among Intel drivers and follow established convention. Signed-off-by: Stephen Hemminger Tested-by: Aaron Brown Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/e1000/e1000_main.c | 5 +++-- drivers/net/ethernet/intel/e1000e/netdev.c | 7 ++++++- drivers/net/ethernet/intel/igb/igb_main.c | 7 ++++++- drivers/net/ethernet/intel/igbvf/netdev.c | 7 ++++++- drivers/net/ethernet/intel/ixgb/ixgb_main.c | 6 +++--- drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 9 ++++++--- drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c | 7 +++++-- 7 files changed, 35 insertions(+), 13 deletions(-) diff --git a/drivers/net/ethernet/intel/e1000/e1000_main.c b/drivers/net/ethernet/intel/e1000/e1000_main.c index bcba9cfe3d03..4348b6fd44fa 100644 --- a/drivers/net/ethernet/intel/e1000/e1000_main.c +++ b/drivers/net/ethernet/intel/e1000/e1000_main.c @@ -217,7 +217,8 @@ MODULE_DESCRIPTION("Intel(R) PRO/1000 Network Driver"); MODULE_LICENSE("GPL"); MODULE_VERSION(DRV_VERSION); -static int debug = NETIF_MSG_DRV | NETIF_MSG_PROBE; +#define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK) +static int debug = -1; module_param(debug, int, 0); MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); @@ -981,7 +982,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev, adapter = netdev_priv(netdev); adapter->netdev = netdev; adapter->pdev = pdev; - adapter->msg_enable = (1 << debug) - 1; + adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE); adapter->bars = bars; adapter->need_ioport = need_ioport; diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c index 7152eb11b7b9..2c38a65ade87 100644 --- a/drivers/net/ethernet/intel/e1000e/netdev.c +++ b/drivers/net/ethernet/intel/e1000e/netdev.c @@ -60,6 +60,11 @@ char e1000e_driver_name[] = "e1000e"; const char e1000e_driver_version[] = DRV_VERSION; +#define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK) +static int debug = -1; +module_param(debug, int, 0); +MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); + static void e1000e_disable_aspm(struct pci_dev *pdev, u16 state); static const struct e1000_info *e1000_info_tbl[] = { @@ -6172,7 +6177,7 @@ static int __devinit e1000_probe(struct pci_dev *pdev, adapter->hw.adapter = adapter; adapter->hw.mac.type = ei->mac; adapter->max_hw_frame_size = ei->max_hw_frame_size; - adapter->msg_enable = (1 << NETIF_MSG_DRV | NETIF_MSG_PROBE) - 1; + adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE); mmio_start = pci_resource_start(pdev, 0); mmio_len = pci_resource_len(pdev, 0); diff --git a/drivers/net/ethernet/intel/igb/igb_main.c b/drivers/net/ethernet/intel/igb/igb_main.c index c4902411d749..5ec31598ee47 100644 --- a/drivers/net/ethernet/intel/igb/igb_main.c +++ b/drivers/net/ethernet/intel/igb/igb_main.c @@ -238,6 +238,11 @@ MODULE_DESCRIPTION("Intel(R) Gigabit Ethernet Network Driver"); MODULE_LICENSE("GPL"); MODULE_VERSION(DRV_VERSION); +#define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK) +static int debug = -1; +module_param(debug, int, 0); +MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); + struct igb_reg_info { u32 ofs; char *name; @@ -1893,7 +1898,7 @@ static int __devinit igb_probe(struct pci_dev *pdev, adapter->pdev = pdev; hw = &adapter->hw; hw->back = adapter; - adapter->msg_enable = NETIF_MSG_DRV | NETIF_MSG_PROBE; + adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE); mmio_start = pci_resource_start(pdev, 0); mmio_len = pci_resource_len(pdev, 0); diff --git a/drivers/net/ethernet/intel/igbvf/netdev.c b/drivers/net/ethernet/intel/igbvf/netdev.c index 217c143686d2..d61ca2a732f0 100644 --- a/drivers/net/ethernet/intel/igbvf/netdev.c +++ b/drivers/net/ethernet/intel/igbvf/netdev.c @@ -55,6 +55,11 @@ static const char igbvf_driver_string[] = static const char igbvf_copyright[] = "Copyright (c) 2009 - 2012 Intel Corporation."; +#define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK) +static int debug = -1; +module_param(debug, int, 0); +MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); + static int igbvf_poll(struct napi_struct *napi, int budget); static void igbvf_reset(struct igbvf_adapter *); static void igbvf_set_interrupt_capability(struct igbvf_adapter *); @@ -2649,7 +2654,7 @@ static int __devinit igbvf_probe(struct pci_dev *pdev, adapter->flags = ei->flags; adapter->hw.back = adapter; adapter->hw.mac.type = ei->mac; - adapter->msg_enable = (1 << NETIF_MSG_DRV | NETIF_MSG_PROBE) - 1; + adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE); /* PCI config space info */ diff --git a/drivers/net/ethernet/intel/ixgb/ixgb_main.c b/drivers/net/ethernet/intel/ixgb/ixgb_main.c index 82aaa792cbf3..5fce363d810a 100644 --- a/drivers/net/ethernet/intel/ixgb/ixgb_main.c +++ b/drivers/net/ethernet/intel/ixgb/ixgb_main.c @@ -134,8 +134,8 @@ MODULE_DESCRIPTION("Intel(R) PRO/10GbE Network Driver"); MODULE_LICENSE("GPL"); MODULE_VERSION(DRV_VERSION); -#define DEFAULT_DEBUG_LEVEL_SHIFT 3 -static int debug = DEFAULT_DEBUG_LEVEL_SHIFT; +#define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK) +static int debug = -1; module_param(debug, int, 0); MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); @@ -442,7 +442,7 @@ ixgb_probe(struct pci_dev *pdev, const struct pci_device_id *ent) adapter->netdev = netdev; adapter->pdev = pdev; adapter->hw.back = adapter; - adapter->msg_enable = netif_msg_init(debug, DEFAULT_DEBUG_LEVEL_SHIFT); + adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE); adapter->hw.hw_addr = pci_ioremap_bar(pdev, BAR_0); if (!adapter->hw.hw_addr) { diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index 398fc223cab9..6dbad2b2d0b5 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -141,13 +141,16 @@ module_param(allow_unsupported_sfp, uint, 0); MODULE_PARM_DESC(allow_unsupported_sfp, "Allow unsupported and untested SFP+ modules on 82599-based adapters"); +#define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK) +static int debug = -1; +module_param(debug, int, 0); +MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); + MODULE_AUTHOR("Intel Corporation, "); MODULE_DESCRIPTION("Intel(R) 10 Gigabit PCI Express Network Driver"); MODULE_LICENSE("GPL"); MODULE_VERSION(DRV_VERSION); -#define DEFAULT_DEBUG_LEVEL_SHIFT 3 - static void ixgbe_service_event_schedule(struct ixgbe_adapter *adapter) { if (!test_bit(__IXGBE_DOWN, &adapter->state) && @@ -6834,7 +6837,7 @@ static int __devinit ixgbe_probe(struct pci_dev *pdev, adapter->pdev = pdev; hw = &adapter->hw; hw->back = adapter; - adapter->msg_enable = (1 << DEFAULT_DEBUG_LEVEL_SHIFT) - 1; + adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE); hw->hw_addr = ioremap(pci_resource_start(pdev, 0), pci_resource_len(pdev, 0)); diff --git a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c index 581c65976bb4..307611ae831d 100644 --- a/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c +++ b/drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c @@ -91,7 +91,10 @@ MODULE_DESCRIPTION("Intel(R) 82599 Virtual Function Driver"); MODULE_LICENSE("GPL"); MODULE_VERSION(DRV_VERSION); -#define DEFAULT_DEBUG_LEVEL_SHIFT 3 +#define DEFAULT_MSG_ENABLE (NETIF_MSG_DRV|NETIF_MSG_PROBE|NETIF_MSG_LINK) +static int debug = -1; +module_param(debug, int, 0); +MODULE_PARM_DESC(debug, "Debug level (0=none,...,16=all)"); /* forward decls */ static void ixgbevf_set_itr_msix(struct ixgbevf_q_vector *q_vector); @@ -3367,7 +3370,7 @@ static int __devinit ixgbevf_probe(struct pci_dev *pdev, adapter->pdev = pdev; hw = &adapter->hw; hw->back = adapter; - adapter->msg_enable = (1 << DEFAULT_DEBUG_LEVEL_SHIFT) - 1; + adapter->msg_enable = netif_msg_init(debug, DEFAULT_MSG_ENABLE); /* * call save state here in standalone driver because it relies on -- cgit v1.2.3 From 70e5576cb0af5c1351432704a39319af119584bb Mon Sep 17 00:00:00 2001 From: Don Skidmore Date: Thu, 15 Mar 2012 04:55:59 +0000 Subject: ixgbe: fix typo in enumeration name This was pointed out to me by Xiaojun Zhang on Source Forge. CC: Xiaojun Zhang Signed-off-by: Don Skidmore Tested-by: Phil Schmitt Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/ixgbe/ixgbe.h | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe.h b/drivers/net/ethernet/intel/ixgbe/ixgbe.h index 80e26ff30ebf..74e192107f9a 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe.h +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe.h @@ -544,7 +544,7 @@ struct ixgbe_fdir_filter { u16 action; }; -enum ixbge_state_t { +enum ixgbe_state_t { __IXGBE_TESTING, __IXGBE_RESETTING, __IXGBE_DOWN, -- cgit v1.2.3 From 8e4f3250f4162315fd57190d3364210eacafd7c7 Mon Sep 17 00:00:00 2001 From: Don Skidmore Date: Fri, 16 Mar 2012 05:41:48 +0000 Subject: ixgbe: update version number Update the driver version number to better match version of out of tree driver that has similar functionality. Signed-off-by: Don Skidmore Tested-by: Phil Schmitt Signed-off-by: Jeff Kirsher --- drivers/net/ethernet/intel/ixgbe/ixgbe_main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c index 6dbad2b2d0b5..3e26b1f9ac75 100644 --- a/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c +++ b/drivers/net/ethernet/intel/ixgbe/ixgbe_main.c @@ -63,8 +63,8 @@ static char ixgbe_default_device_descr[] = "Intel(R) 10 Gigabit Network Connection"; #endif #define MAJ 3 -#define MIN 6 -#define BUILD 7 +#define MIN 8 +#define BUILD 21 #define DRV_VERSION __stringify(MAJ) "." __stringify(MIN) "." \ __stringify(BUILD) "-k" const char ixgbe_driver_version[] = DRV_VERSION; -- cgit v1.2.3 From 2e57b79ccef1ff1422fdf45a9b28fe60f8f084f7 Mon Sep 17 00:00:00 2001 From: Rick Jones Date: Tue, 27 Mar 2012 07:28:09 +0000 Subject: virtio_net: do not rate limit counter increments While it is desirable to rate limit certain messages, it is not desirable to rate limit the incrementing of counters associated with those messages. Signed-off-by: Rick Jones Acked-by: Rusty Russell Acked-by: Michael S. Tsirkin Signed-off-by: David S. Miller --- drivers/net/virtio_net.c | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-) diff --git a/drivers/net/virtio_net.c b/drivers/net/virtio_net.c index 019da012669f..4de2760c5937 100644 --- a/drivers/net/virtio_net.c +++ b/drivers/net/virtio_net.c @@ -625,12 +625,13 @@ static netdev_tx_t start_xmit(struct sk_buff *skb, struct net_device *dev) /* This can happen with OOM and indirect buffers. */ if (unlikely(capacity < 0)) { - if (net_ratelimit()) { - if (likely(capacity == -ENOMEM)) { + if (likely(capacity == -ENOMEM)) { + if (net_ratelimit()) { dev_warn(&dev->dev, "TX queue failure: out of memory\n"); } else { - dev->stats.tx_fifo_errors++; + dev->stats.tx_fifo_errors++; + if (net_ratelimit()) dev_warn(&dev->dev, "Unexpected TX queue failure: %d\n", capacity); -- cgit v1.2.3 From 4e7b2f1454382b220f792a7fbcbebd0985187161 Mon Sep 17 00:00:00 2001 From: Benjamin LaHaise Date: Tue, 27 Mar 2012 15:55:32 +0000 Subject: net/ipv4: fix IPv4 multicast over network namespaces When using multicast over a local bridge feeding a number of LXC guests using veth, the LXC guests are unable to get a response from other guests when pinging 224.0.0.1. Multicast packets did not appear to be getting delivered to the network namespaces of the guest hosts, and further inspection showed that the incoming route was pointing to the loopback device of the host, not the guest. This lead to the wrong network namespace being picked up by sockets (like ICMP). Fix this by using the correct network namespace when creating the inbound route entry. Signed-off-by: Benjamin LaHaise Signed-off-by: David S. Miller --- net/ipv4/route.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/ipv4/route.c b/net/ipv4/route.c index 12ccf880eb88..3b110a46362c 100644 --- a/net/ipv4/route.c +++ b/net/ipv4/route.c @@ -2042,7 +2042,7 @@ static int ip_route_input_mc(struct sk_buff *skb, __be32 daddr, __be32 saddr, if (err < 0) goto e_err; } - rth = rt_dst_alloc(init_net.loopback_dev, + rth = rt_dst_alloc(dev_net(dev)->loopback_dev, IN_DEV_CONF_GET(in_dev, NOPOLICY), false); if (!rth) goto e_nobufs; -- cgit v1.2.3 From 3b9785c6b0ff37ac4ef5085b38756283da84dceb Mon Sep 17 00:00:00 2001 From: Benjamin LaHaise Date: Tue, 27 Mar 2012 15:55:44 +0000 Subject: net/core: dev_forward_skb() should clear skb_iif While investigating another bug, I found that the code on the incoming path in __netif_receive_skb will only set skb->skb_iif if it is already 0. When dev_forward_skb() is used in the case of interfaces like veth, skb_iif may already have been set. Making dev_forward_skb() cause the packet to look like a newly received packet would seem to the the correct behaviour here, as otherwise the wrong incoming interface can be reported for such a packet. Signed-off-by: Benjamin LaHaise Signed-off-by: David S. Miller --- net/core/dev.c | 1 + 1 file changed, 1 insertion(+) diff --git a/net/core/dev.c b/net/core/dev.c index 452db7090d18..723a4065a00e 100644 --- a/net/core/dev.c +++ b/net/core/dev.c @@ -1597,6 +1597,7 @@ int dev_forward_skb(struct net_device *dev, struct sk_buff *skb) kfree_skb(skb); return NET_RX_DROP; } + skb->skb_iif = 0; skb_set_dev(skb, dev); skb->tstamp.tv64 = 0; skb->pkt_type = PACKET_HOST; -- cgit v1.2.3 From 75836b8daefdde84f8b5dde1be5b67d858139df3 Mon Sep 17 00:00:00 2001 From: Stanislav Yakovlev Date: Tue, 20 Mar 2012 17:52:57 -0400 Subject: net/wireless: ipw2x00: fix a typo in wiphy struct initilization Fix comment as well. Signed-off-by: Stanislav Yakovlev Signed-off-by: John W. Linville --- drivers/net/wireless/ipw2x00/ipw2200.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/ipw2x00/ipw2200.c b/drivers/net/wireless/ipw2x00/ipw2200.c index 4fcdac63a300..2b022571a859 100644 --- a/drivers/net/wireless/ipw2x00/ipw2200.c +++ b/drivers/net/wireless/ipw2x00/ipw2200.c @@ -11507,9 +11507,9 @@ static int ipw_wdev_init(struct net_device *dev) rc = -ENOMEM; goto out; } - /* translate geo->bg to a_band.channels */ + /* translate geo->a to a_band.channels */ for (i = 0; i < geo->a_channels; i++) { - a_band->channels[i].band = IEEE80211_BAND_2GHZ; + a_band->channels[i].band = IEEE80211_BAND_5GHZ; a_band->channels[i].center_freq = geo->a[i].freq; a_band->channels[i].hw_value = geo->a[i].channel; a_band->channels[i].max_power = geo->a[i].max_power; -- cgit v1.2.3 From e90c7e712980bf794f88f749e2a1270e4a4a116e Mon Sep 17 00:00:00 2001 From: Santosh Nayak Date: Thu, 22 Mar 2012 12:42:41 +0530 Subject: net: orinoco: add error handling for failed kmalloc(). With flag 'GFP_ATOMIC', probability of allocation failure is more. Add error handling after kmalloc() call to avoid null dereference. Signed-off-by: Santosh Nayak Signed-off-by: John W. Linville --- drivers/net/wireless/orinoco/main.c | 8 ++++++++ 1 file changed, 8 insertions(+) diff --git a/drivers/net/wireless/orinoco/main.c b/drivers/net/wireless/orinoco/main.c index dd6c64ac406e..88e3ad2d1db8 100644 --- a/drivers/net/wireless/orinoco/main.c +++ b/drivers/net/wireless/orinoco/main.c @@ -1336,6 +1336,10 @@ static void qbuf_scan(struct orinoco_private *priv, void *buf, unsigned long flags; sd = kmalloc(sizeof(*sd), GFP_ATOMIC); + if (!sd) { + printk(KERN_ERR "%s: failed to alloc memory\n", __func__); + return; + } sd->buf = buf; sd->len = len; sd->type = type; @@ -1353,6 +1357,10 @@ static void qabort_scan(struct orinoco_private *priv) unsigned long flags; sd = kmalloc(sizeof(*sd), GFP_ATOMIC); + if (!sd) { + printk(KERN_ERR "%s: failed to alloc memory\n", __func__); + return; + } sd->len = -1; /* Abort */ spin_lock_irqsave(&priv->scan_lock, flags); -- cgit v1.2.3 From ca907a90735877ceff800d08f780f2f1b4388afa Mon Sep 17 00:00:00 2001 From: Stanislav Yakovlev Date: Sat, 24 Mar 2012 03:41:01 -0400 Subject: MAINTAINERS: adding maintainer for ipw2x00 Add myself as maintainer as suggested by Stanislaw Gruszka. Signed-off-by: Stanislav Yakovlev Signed-off-by: John W. Linville --- MAINTAINERS | 12 ++++-------- 1 file changed, 4 insertions(+), 8 deletions(-) diff --git a/MAINTAINERS b/MAINTAINERS index 0ddc77fe46b6..09a79f9f1d3c 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -3519,17 +3519,13 @@ L: linux-pm@vger.kernel.org S: Supported F: arch/x86/platform/mrst/pmu.* -INTEL PRO/WIRELESS 2100 NETWORK CONNECTION SUPPORT +INTEL PRO/WIRELESS 2100, 2200BG, 2915ABG NETWORK CONNECTION SUPPORT +M: Stanislav Yakovlev L: linux-wireless@vger.kernel.org -S: Orphan +S: Maintained F: Documentation/networking/README.ipw2100 -F: drivers/net/wireless/ipw2x00/ipw2100.* - -INTEL PRO/WIRELESS 2915ABG NETWORK CONNECTION SUPPORT -L: linux-wireless@vger.kernel.org -S: Orphan F: Documentation/networking/README.ipw2200 -F: drivers/net/wireless/ipw2x00/ipw2200.* +F: drivers/net/wireless/ipw2x00/ INTEL(R) TRUSTED EXECUTION TECHNOLOGY (TXT) M: Joseph Cihula -- cgit v1.2.3 From a4d6367fa77fb604ce62582e1c0998e0ed098927 Mon Sep 17 00:00:00 2001 From: Sujith Manoharan Date: Tue, 27 Mar 2012 10:08:55 +0530 Subject: ath9k: Use HW HT capabilites properly The commit "ath9k: Remove aggregation flags" changed how nodes were being initialized. Use the HW HT cap bits to initialize/de-initialize nodes, else we would be accessing an uninitialized entry during a suspend/resume cycle, resulting in a panic. Reported-by: Justin P. Mattock Signed-off-by: Sujith Manoharan Signed-off-by: John W. Linville --- drivers/net/wireless/ath/ath9k/main.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 38794850f005..215eb2536b1e 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -640,7 +640,7 @@ static void ath_node_attach(struct ath_softc *sc, struct ieee80211_sta *sta, an->sta = sta; an->vif = vif; - if (sta->ht_cap.ht_supported) { + if (sc->sc_ah->caps.hw_caps & ATH9K_HW_CAP_HT) { ath_tx_node_init(sc, an); an->maxampdu = 1 << (IEEE80211_HT_MAX_AMPDU_FACTOR + sta->ht_cap.ampdu_factor); @@ -659,7 +659,7 @@ static void ath_node_detach(struct ath_softc *sc, struct ieee80211_sta *sta) an->sta = NULL; #endif - if (sta->ht_cap.ht_supported) + if (sc->sc_ah->caps.hw_caps & ATH9K_HW_CAP_HT) ath_tx_node_cleanup(sc, an); } -- cgit v1.2.3 From de312db345f9770b64ff39ef5a7f86f6358e93cc Mon Sep 17 00:00:00 2001 From: Rajkumar Manoharan Date: Tue, 27 Mar 2012 11:01:06 +0530 Subject: mac80211: fix oper channel timestamp updation Whenever the station informs the AP that it is about to leave the operating channel, the timestamp should be recorded. It is handled in scan resume but not in scan start. Fix that. Signed-off-by: Rajkumar Manoharan Signed-off-by: John W. Linville --- net/mac80211/scan.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/mac80211/scan.c b/net/mac80211/scan.c index 33cd16901378..c70e17677135 100644 --- a/net/mac80211/scan.c +++ b/net/mac80211/scan.c @@ -370,7 +370,7 @@ static int ieee80211_start_sw_scan(struct ieee80211_local *local) */ drv_sw_scan_start(local); - local->leave_oper_channel_time = 0; + local->leave_oper_channel_time = jiffies; local->next_scan_state = SCAN_DECISION; local->scan_channel_idx = 0; -- cgit v1.2.3 From 7d26bb103c4162003bfdf1d63aaa32b548ad0e9a Mon Sep 17 00:00:00 2001 From: Weiping Pan Date: Tue, 27 Mar 2012 19:18:24 +0000 Subject: bonding: emit event when bonding changes MAC When a bonding device is configured with fail_over_mac=active, we expect to see the MAC address of the new active slave as the source MAC address after failover. But we see that the source MAC address is the MAC address of previous active slave. Emit NETDEV_CHANGEADDR event when bonding changes its MAC address, in order to let arp_netdev_event flush neighbour cache and route cache. How to reproduce this bug ? -----------hostB---------------- hostA ----- switch ---|-- eth0--bond0(192.168.100.2/24)| (192.168.100.1/24 \--|-- eth1-/ | -------------------------------- 1 on hostB, modprobe bonding mode=1 miimon=500 fail_over_mac=active downdelay=1000 num_grat_arp=1 ifconfig bond0 192.168.100.2/24 up ifenslave bond0 eth0 ifenslave bond0 eth1 then eth0 is the active slave, and MAC of bond0 is MAC of eth0. 2 on hostA, ping 192.168.100.2 3 on hostB, tcpdump -i bond0 -p icmp -XXX you will see bond0 uses MAC of eth0 as source MAC in icmp reply. 4 on hostB, ifconfig eth0 down tcpdump -i bond0 -p icmp -XXX (just keep it running in step 3) you will see first bond0 uses MAC of eth1 as source MAC in icmp reply, then it will use MAC of eth0 as source MAC. Signed-off-by: Weiping Pan Signed-off-by: Jay Vosburgh Signed-off-by: David S. Miller --- drivers/net/bonding/bond_main.c | 8 +++++++- 1 file changed, 7 insertions(+), 1 deletion(-) diff --git a/drivers/net/bonding/bond_main.c b/drivers/net/bonding/bond_main.c index b920d829692a..a20b5850e7ce 100644 --- a/drivers/net/bonding/bond_main.c +++ b/drivers/net/bonding/bond_main.c @@ -892,9 +892,15 @@ static void bond_do_fail_over_mac(struct bonding *bond, switch (bond->params.fail_over_mac) { case BOND_FOM_ACTIVE: - if (new_active) + if (new_active) { memcpy(bond->dev->dev_addr, new_active->dev->dev_addr, new_active->dev->addr_len); + write_unlock_bh(&bond->curr_slave_lock); + read_unlock(&bond->lock); + call_netdevice_notifiers(NETDEV_CHANGEADDR, bond->dev); + read_lock(&bond->lock); + write_lock_bh(&bond->curr_slave_lock); + } break; case BOND_FOM_FOLLOW: /* -- cgit v1.2.3 From 1d24fb3684f347226747c6b11ea426b7b992694e Mon Sep 17 00:00:00 2001 From: "zhuangfeiran@ict.ac.cn" Date: Wed, 28 Mar 2012 23:27:00 +0000 Subject: x86 bpf_jit: fix a bug in emitting the 16-bit immediate operand of AND When K >= 0xFFFF0000, AND needs the two least significant bytes of K as its operand, but EMIT2() gives it the least significant byte of K and 0x2. EMIT() should be used here to replace EMIT2(). Signed-off-by: Feiran Zhuang Acked-by: Eric Dumazet Signed-off-by: David S. Miller --- arch/x86/net/bpf_jit_comp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/arch/x86/net/bpf_jit_comp.c b/arch/x86/net/bpf_jit_comp.c index 5671752f8d9c..5a5b6e4dd738 100644 --- a/arch/x86/net/bpf_jit_comp.c +++ b/arch/x86/net/bpf_jit_comp.c @@ -289,7 +289,7 @@ void bpf_jit_compile(struct sk_filter *fp) EMIT2(0x24, K & 0xFF); /* and imm8,%al */ } else if (K >= 0xFFFF0000) { EMIT2(0x66, 0x25); /* and imm16,%ax */ - EMIT2(K, 2); + EMIT(K, 2); } else { EMIT1_off32(0x25, K); /* and imm32,%eax */ } -- cgit v1.2.3 From 67378563df2e168d32a4054616f244a91aec462d Mon Sep 17 00:00:00 2001 From: David Ward Date: Tue, 27 Mar 2012 09:01:52 +0000 Subject: net/garp: avoid infinite loop if attribute already exists An infinite loop occurred if garp_attr_create was called with the values of an existing attribute. This might happen if a previous leave request for the attribute has not yet been followed by a PDU transmission (or, if the application previously issued a join request for the attribute and is now issuing another one, without having issued a leave request). If garp_attr_create finds an existing attribute having the same values, return the address to it. Its state will then get updated (i.e., if it was in a leaving state, it will move into a non-leaving state and not get deleted during the next PDU transmission). To accomplish this fix, collapse garp_attr_insert into garp_attr_create (which is its only caller). Thanks to Jorge Boncompte [DTI2] for contributing to this fix. Signed-off-by: David Ward Acked-by: Jorge Boncompte [DTI2] Signed-off-by: David S. Miller --- net/802/garp.c | 22 ++++++++++------------ 1 file changed, 10 insertions(+), 12 deletions(-) diff --git a/net/802/garp.c b/net/802/garp.c index 8e21b6db3981..a5c224830439 100644 --- a/net/802/garp.c +++ b/net/802/garp.c @@ -167,7 +167,8 @@ static struct garp_attr *garp_attr_lookup(const struct garp_applicant *app, return NULL; } -static void garp_attr_insert(struct garp_applicant *app, struct garp_attr *new) +static struct garp_attr *garp_attr_create(struct garp_applicant *app, + const void *data, u8 len, u8 type) { struct rb_node *parent = NULL, **p = &app->gid.rb_node; struct garp_attr *attr; @@ -176,21 +177,16 @@ static void garp_attr_insert(struct garp_applicant *app, struct garp_attr *new) while (*p) { parent = *p; attr = rb_entry(parent, struct garp_attr, node); - d = garp_attr_cmp(attr, new->data, new->dlen, new->type); + d = garp_attr_cmp(attr, data, len, type); if (d < 0) p = &parent->rb_left; else if (d > 0) p = &parent->rb_right; + else { + /* The attribute already exists; re-use it. */ + return attr; + } } - rb_link_node(&new->node, parent, p); - rb_insert_color(&new->node, &app->gid); -} - -static struct garp_attr *garp_attr_create(struct garp_applicant *app, - const void *data, u8 len, u8 type) -{ - struct garp_attr *attr; - attr = kmalloc(sizeof(*attr) + len, GFP_ATOMIC); if (!attr) return attr; @@ -198,7 +194,9 @@ static struct garp_attr *garp_attr_create(struct garp_applicant *app, attr->type = type; attr->dlen = len; memcpy(attr->data, data, len); - garp_attr_insert(app, attr); + + rb_link_node(&attr->node, parent, p); + rb_insert_color(&attr->node, &app->gid); return attr; } -- cgit v1.2.3 From 464b57da56910c8737ede75ad820b9a7afc46b3e Mon Sep 17 00:00:00 2001 From: Kenth Eriksson Date: Tue, 27 Mar 2012 22:05:54 +0000 Subject: Fix non TBI PHY access; a bad merge undid bug fix in a previous commit. The merge done in commit b26e478f undid bug fix in commit c3e072f8 ("net: fsl_pq_mdio: fix non tbi phy access"), with the result that non TBI (e.g. MDIO) PHYs cannot be accessed. Signed-off-by: Kenth Eriksson Signed-off-by: David S. Miller --- drivers/net/ethernet/freescale/fsl_pq_mdio.c | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) diff --git a/drivers/net/ethernet/freescale/fsl_pq_mdio.c b/drivers/net/ethernet/freescale/fsl_pq_mdio.c index 9eb815941df5..f7f0bf5d037b 100644 --- a/drivers/net/ethernet/freescale/fsl_pq_mdio.c +++ b/drivers/net/ethernet/freescale/fsl_pq_mdio.c @@ -356,13 +356,13 @@ static int fsl_pq_mdio_probe(struct platform_device *ofdev) if (prop) tbiaddr = *prop; - } - if (tbiaddr == -1) { - err = -EBUSY; - goto err_free_irqs; - } else { - out_be32(tbipa, tbiaddr); + if (tbiaddr == -1) { + err = -EBUSY; + goto err_free_irqs; + } else { + out_be32(tbipa, tbiaddr); + } } err = of_mdiobus_register(new_bus, np); -- cgit v1.2.3 From 81213b5e8ae68e204aa7a3f83c4f9100405dbff9 Mon Sep 17 00:00:00 2001 From: "danborkmann@iogearbox.net" Date: Tue, 27 Mar 2012 22:47:43 +0000 Subject: rose_dev: fix memcpy-bug in rose_set_mac_address If both addresses equal, nothing needs to be done. If the device is down, then we simply copy the new address to dev->dev_addr. If the device is up, then we add another loopback device with the new address, and if that does not fail, we remove the loopback device with the old address. And only then, we update the dev->dev_addr. Signed-off-by: Daniel Borkmann Signed-off-by: David S. Miller --- net/rose/rose_dev.c | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) diff --git a/net/rose/rose_dev.c b/net/rose/rose_dev.c index 178ff4f73c85..2679507ad333 100644 --- a/net/rose/rose_dev.c +++ b/net/rose/rose_dev.c @@ -96,11 +96,11 @@ static int rose_set_mac_address(struct net_device *dev, void *addr) struct sockaddr *sa = addr; int err; - if (!memcpy(dev->dev_addr, sa->sa_data, dev->addr_len)) + if (!memcmp(dev->dev_addr, sa->sa_data, dev->addr_len)) return 0; if (dev->flags & IFF_UP) { - err = rose_add_loopback_node((rose_address *)dev->dev_addr); + err = rose_add_loopback_node((rose_address *)sa->sa_data); if (err) return err; -- cgit v1.2.3 From 6523cf9a460c488c681b7e4ecef2395491de1d4e Mon Sep 17 00:00:00 2001 From: Andrew Morton Date: Wed, 28 Mar 2012 12:10:57 +0000 Subject: net/netfilter/nfnetlink_acct.c: use linux/atomic.h There's no known problem here, but this is one of only two non-arch files in the kernel which use asm/atomic.h instead of linux/atomic.h. Acked-by: Pablo Neira Ayuso Cc: Patrick McHardy Cc: "David S. Miller" Signed-off-by: Andrew Morton Signed-off-by: David S. Miller --- net/netfilter/nfnetlink_acct.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/net/netfilter/nfnetlink_acct.c b/net/netfilter/nfnetlink_acct.c index 3eb348bfc4fb..d98c868c148b 100644 --- a/net/netfilter/nfnetlink_acct.c +++ b/net/netfilter/nfnetlink_acct.c @@ -10,6 +10,7 @@ #include #include #include +#include #include #include #include @@ -17,7 +18,6 @@ #include #include #include -#include #include #include -- cgit v1.2.3 From cdaf0b835df04177397b90214f8b457fd23b67e0 Mon Sep 17 00:00:00 2001 From: "stigge@antcom.de" Date: Wed, 28 Mar 2012 12:36:26 +0000 Subject: net: lpc_eth: Fix rename of dev_hw_addr_random In parallel to the integration of lpc_eth.c, dev_hw_addr_random() has been renamed to eth_hw_addr_random(). This patch fixes it also in the new driver lpc_eth.c. Signed-off-by: Roland Stigge Signed-off-by: David S. Miller --- drivers/net/ethernet/nxp/lpc_eth.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-) diff --git a/drivers/net/ethernet/nxp/lpc_eth.c b/drivers/net/ethernet/nxp/lpc_eth.c index 69444247c20b..6dfc26d85e47 100644 --- a/drivers/net/ethernet/nxp/lpc_eth.c +++ b/drivers/net/ethernet/nxp/lpc_eth.c @@ -1441,7 +1441,7 @@ static int lpc_eth_drv_probe(struct platform_device *pdev) } #endif if (!is_valid_ether_addr(ndev->dev_addr)) - dev_hw_addr_random(ndev, ndev->dev_addr); + eth_hw_addr_random(ndev); /* Reset the ethernet controller */ __lpc_eth_reset(pldat); -- cgit v1.2.3 From 72331bc0cd072c3f4b670cd1256e47681fc53b80 Mon Sep 17 00:00:00 2001 From: Shmulik Ladkani Date: Sun, 1 Apr 2012 04:03:45 +0000 Subject: ipv6: Fix RTM_GETROUTE's interpretation of RTA_IIF to be consistent with ipv4 In IPv4, if an RTA_IIF attribute is specified within an RTM_GETROUTE message, then a route is searched as if a packet was received on the specified 'iif' interface. However in IPv6, RTA_IIF is not interpreted in the same way: 'inet6_rtm_getroute()' always calls 'ip6_route_output()', regardless the RTA_IIF attribute. As a result, in IPv6 there's no way to use RTM_GETROUTE in order to look for a route as if a packet was received on a specific interface. Fix 'inet6_rtm_getroute()' so that RTA_IIF is interpreted as "lookup a route as if a packet was received on the specified interface", similar to IPv4's 'inet_rtm_getroute()' interpretation. Reported-by: Ami Koren Signed-off-by: Shmulik Ladkani Signed-off-by: David S. Miller --- net/ipv6/route.c | 34 +++++++++++++++++++++++++++------- 1 file changed, 27 insertions(+), 7 deletions(-) diff --git a/net/ipv6/route.c b/net/ipv6/route.c index 496b62712fe8..3992e26a6039 100644 --- a/net/ipv6/route.c +++ b/net/ipv6/route.c @@ -881,6 +881,16 @@ static struct rt6_info *ip6_pol_route_input(struct net *net, struct fib6_table * return ip6_pol_route(net, table, fl6->flowi6_iif, fl6, flags); } +static struct dst_entry *ip6_route_input_lookup(struct net *net, + struct net_device *dev, + struct flowi6 *fl6, int flags) +{ + if (rt6_need_strict(&fl6->daddr) && dev->type != ARPHRD_PIMREG) + flags |= RT6_LOOKUP_F_IFACE; + + return fib6_rule_lookup(net, fl6, flags, ip6_pol_route_input); +} + void ip6_route_input(struct sk_buff *skb) { const struct ipv6hdr *iph = ipv6_hdr(skb); @@ -895,10 +905,7 @@ void ip6_route_input(struct sk_buff *skb) .flowi6_proto = iph->nexthdr, }; - if (rt6_need_strict(&iph->daddr) && skb->dev->type != ARPHRD_PIMREG) - flags |= RT6_LOOKUP_F_IFACE; - - skb_dst_set(skb, fib6_rule_lookup(net, &fl6, flags, ip6_pol_route_input)); + skb_dst_set(skb, ip6_route_input_lookup(net, skb->dev, &fl6, flags)); } static struct rt6_info *ip6_pol_route_output(struct net *net, struct fib6_table *table, @@ -2537,7 +2544,7 @@ static int inet6_rtm_getroute(struct sk_buff *in_skb, struct nlmsghdr* nlh, void struct sk_buff *skb; struct rtmsg *rtm; struct flowi6 fl6; - int err, iif = 0; + int err, iif = 0, oif = 0; err = nlmsg_parse(nlh, sizeof(*rtm), tb, RTA_MAX, rtm_ipv6_policy); if (err < 0) @@ -2564,15 +2571,29 @@ static int inet6_rtm_getroute(struct sk_buff *in_skb, struct nlmsghdr* nlh, void iif = nla_get_u32(tb[RTA_IIF]); if (tb[RTA_OIF]) - fl6.flowi6_oif = nla_get_u32(tb[RTA_OIF]); + oif = nla_get_u32(tb[RTA_OIF]); if (iif) { struct net_device *dev; + int flags = 0; + dev = __dev_get_by_index(net, iif); if (!dev) { err = -ENODEV; goto errout; } + + fl6.flowi6_iif = iif; + + if (!ipv6_addr_any(&fl6.saddr)) + flags |= RT6_LOOKUP_F_HAS_SADDR; + + rt = (struct rt6_info *)ip6_route_input_lookup(net, dev, &fl6, + flags); + } else { + fl6.flowi6_oif = oif; + + rt = (struct rt6_info *)ip6_route_output(net, NULL, &fl6); } skb = alloc_skb(NLMSG_GOODSIZE, GFP_KERNEL); @@ -2587,7 +2608,6 @@ static int inet6_rtm_getroute(struct sk_buff *in_skb, struct nlmsghdr* nlh, void skb_reset_mac_header(skb); skb_reserve(skb, MAX_HEADER + sizeof(struct ipv6hdr)); - rt = (struct rt6_info*) ip6_route_output(net, NULL, &fl6); skb_dst_set(skb, &rt->dst); err = rt6_fill_node(net, skb, rt, &fl6.daddr, &fl6.saddr, iif, -- cgit v1.2.3 From 3f8c91a7398b9266fbe7abcbe4bd5dffef907643 Mon Sep 17 00:00:00 2001 From: Andreas Mohr Date: Sun, 1 Apr 2012 12:35:00 +0000 Subject: via-rhine: fix wait-bit inversion. Bug appeared in a384a33bb1c9ec2d99db2046b41f57023fa7d77b ("via-rhine: RHINE_WAIT_FOR macro removal). It can be noticed during suspend/resume. Signed-off-by: Andreas Mohr Acked-by: Francois Romieu Cc: David Lv Signed-off-by: David S. Miller --- drivers/net/ethernet/via/via-rhine.c | 12 +++++++----- 1 file changed, 7 insertions(+), 5 deletions(-) diff --git a/drivers/net/ethernet/via/via-rhine.c b/drivers/net/ethernet/via/via-rhine.c index 39b8cf3dafcd..fcfa01f7ceb6 100644 --- a/drivers/net/ethernet/via/via-rhine.c +++ b/drivers/net/ethernet/via/via-rhine.c @@ -503,30 +503,32 @@ static int rhine_vlan_rx_add_vid(struct net_device *dev, unsigned short vid); static int rhine_vlan_rx_kill_vid(struct net_device *dev, unsigned short vid); static void rhine_restart_tx(struct net_device *dev); -static void rhine_wait_bit(struct rhine_private *rp, u8 reg, u8 mask, bool high) +static void rhine_wait_bit(struct rhine_private *rp, u8 reg, u8 mask, bool low) { void __iomem *ioaddr = rp->base; int i; for (i = 0; i < 1024; i++) { - if (high ^ !!(ioread8(ioaddr + reg) & mask)) + bool has_mask_bits = !!(ioread8(ioaddr + reg) & mask); + + if (low ^ has_mask_bits) break; udelay(10); } if (i > 64) { netif_dbg(rp, hw, rp->dev, "%s bit wait (%02x/%02x) cycle " - "count: %04d\n", high ? "high" : "low", reg, mask, i); + "count: %04d\n", low ? "low" : "high", reg, mask, i); } } static void rhine_wait_bit_high(struct rhine_private *rp, u8 reg, u8 mask) { - rhine_wait_bit(rp, reg, mask, true); + rhine_wait_bit(rp, reg, mask, false); } static void rhine_wait_bit_low(struct rhine_private *rp, u8 reg, u8 mask) { - rhine_wait_bit(rp, reg, mask, false); + rhine_wait_bit(rp, reg, mask, true); } static u32 rhine_get_events(struct rhine_private *rp) -- cgit v1.2.3 From acc656323ab904803393acefdc8e1b78cde752e5 Mon Sep 17 00:00:00 2001 From: Akinobu Mita Date: Fri, 30 Mar 2012 01:01:46 +0000 Subject: rionet: fix page allocation order of rionet_active rionet_active is allocated from the page allocator and the allocation order is calculated on the assumption that the page size is 4KB, so it wastes memory on more than 4K page systems. Signed-off-by: Akinobu Mita Cc: Matt Porter Cc: Alexandre Bounine Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller --- drivers/net/rionet.c | 11 ++++++----- 1 file changed, 6 insertions(+), 5 deletions(-) diff --git a/drivers/net/rionet.c b/drivers/net/rionet.c index a57f05726b57..91d25888a1b9 100644 --- a/drivers/net/rionet.c +++ b/drivers/net/rionet.c @@ -375,8 +375,8 @@ static void rionet_remove(struct rio_dev *rdev) struct net_device *ndev = rio_get_drvdata(rdev); struct rionet_peer *peer, *tmp; - free_pages((unsigned long)rionet_active, rdev->net->hport->sys_size ? - __fls(sizeof(void *)) + 4 : 0); + free_pages((unsigned long)rionet_active, get_order(sizeof(void *) * + RIO_MAX_ROUTE_ENTRIES(rdev->net->hport->sys_size))); unregister_netdev(ndev); free_netdev(ndev); @@ -432,15 +432,16 @@ static int rionet_setup_netdev(struct rio_mport *mport, struct net_device *ndev) int rc = 0; struct rionet_private *rnet; u16 device_id; + const size_t rionet_active_bytes = sizeof(void *) * + RIO_MAX_ROUTE_ENTRIES(mport->sys_size); rionet_active = (struct rio_dev **)__get_free_pages(GFP_KERNEL, - mport->sys_size ? __fls(sizeof(void *)) + 4 : 0); + get_order(rionet_active_bytes)); if (!rionet_active) { rc = -ENOMEM; goto out; } - memset((void *)rionet_active, 0, sizeof(void *) * - RIO_MAX_ROUTE_ENTRIES(mport->sys_size)); + memset((void *)rionet_active, 0, rionet_active_bytes); /* Set up private area */ rnet = netdev_priv(ndev); -- cgit v1.2.3 From 6bafd6436e99d08e8def37ae9f790e1aff871bae Mon Sep 17 00:00:00 2001 From: huajun li Date: Fri, 30 Mar 2012 00:11:05 +0000 Subject: usb/rtl8150 : Remove duplicated definitions There exist duplicated macro definitions in rtl8150.c, remove them. Signed-off-by: Huajun Li Signed-off-by: David S. Miller --- drivers/net/usb/rtl8150.c | 26 -------------------------- 1 file changed, 26 deletions(-) diff --git a/drivers/net/usb/rtl8150.c b/drivers/net/usb/rtl8150.c index 6dda2fe5b15b..d363b31053da 100644 --- a/drivers/net/usb/rtl8150.c +++ b/drivers/net/usb/rtl8150.c @@ -59,32 +59,6 @@ #define RTL8150_REQ_SET_REGS 0x05 -/* Transmit status register errors */ -#define TSR_ECOL (1<<5) -#define TSR_LCOL (1<<4) -#define TSR_LOSS_CRS (1<<3) -#define TSR_JBR (1<<2) -#define TSR_ERRORS (TSR_ECOL | TSR_LCOL | TSR_LOSS_CRS | TSR_JBR) -/* Receive status register errors */ -#define RSR_CRC (1<<2) -#define RSR_FAE (1<<1) -#define RSR_ERRORS (RSR_CRC | RSR_FAE) - -/* Media status register definitions */ -#define MSR_DUPLEX (1<<4) -#define MSR_SPEED (1<<3) -#define MSR_LINK (1<<2) - -/* Interrupt pipe data */ -#define INT_TSR 0x00 -#define INT_RSR 0x01 -#define INT_MSR 0x02 -#define INT_WAKSR 0x03 -#define INT_TXOK_CNT 0x04 -#define INT_RXLOST_CNT 0x05 -#define INT_CRERR_CNT 0x06 -#define INT_COL_CNT 0x07 - /* Transmit status register errors */ #define TSR_ECOL (1<<5) #define TSR_LCOL (1<<4) -- cgit v1.2.3 From 10b9194f959608368ed89df1937f17cfe6bd6d84 Mon Sep 17 00:00:00 2001 From: Yoshihiro Shimoda Date: Thu, 29 Mar 2012 19:32:08 +0000 Subject: net: sh_eth: fix endian check for architecture independent SuperH has the "CONFIG_CPU_LITTLE_ENDIAN" and the "__LITTLE_ENDIAN__". But, other architecture doesn't have them. So, this patch fixes it. Signed-off-by: Yoshihiro Shimoda Signed-off-by: David S. Miller --- drivers/net/ethernet/renesas/sh_eth.c | 2 +- drivers/net/ethernet/renesas/sh_eth.h | 4 ++-- 2 files changed, 3 insertions(+), 3 deletions(-) diff --git a/drivers/net/ethernet/renesas/sh_eth.c b/drivers/net/ethernet/renesas/sh_eth.c index 8bdf070ace90..d63e09b29a96 100644 --- a/drivers/net/ethernet/renesas/sh_eth.c +++ b/drivers/net/ethernet/renesas/sh_eth.c @@ -804,7 +804,7 @@ static int sh_eth_dev_init(struct net_device *ndev) /* all sh_eth int mask */ sh_eth_write(ndev, 0, EESIPR); -#if defined(__LITTLE_ENDIAN__) +#if defined(__LITTLE_ENDIAN) if (mdp->cd->hw_swap) sh_eth_write(ndev, EDMR_EL, EDMR); else diff --git a/drivers/net/ethernet/renesas/sh_eth.h b/drivers/net/ethernet/renesas/sh_eth.h index e66de1823532..0fa14afce23d 100644 --- a/drivers/net/ethernet/renesas/sh_eth.h +++ b/drivers/net/ethernet/renesas/sh_eth.h @@ -693,7 +693,7 @@ enum TSU_FWSLC_BIT { */ struct sh_eth_txdesc { u32 status; /* TD0 */ -#if defined(CONFIG_CPU_LITTLE_ENDIAN) +#if defined(__LITTLE_ENDIAN) u16 pad0; /* TD1 */ u16 buffer_length; /* TD1 */ #else @@ -710,7 +710,7 @@ struct sh_eth_txdesc { */ struct sh_eth_rxdesc { u32 status; /* RD0 */ -#if defined(CONFIG_CPU_LITTLE_ENDIAN) +#if defined(__LITTLE_ENDIAN) u16 frame_length; /* RD1 */ u16 buffer_length; /* RD1 */ #else -- cgit v1.2.3 From 78fb72f7936c01d5b426c03a691eca082b03f2b9 Mon Sep 17 00:00:00 2001 From: Rabin Vincent Date: Thu, 29 Mar 2012 07:15:15 +0000 Subject: net: usb: cdc_eem: fix mtu Make CDC EEM recalculate the hard_mtu after adjusting the hard_header_len. Without this, usbnet adjusts the MTU down to 1494 bytes, and the host is unable to receive standard 1500-byte frames from the device. Tested with the Linux USB Ethernet gadget. Cc: Oliver Neukum Signed-off-by: Rabin Vincent Signed-off-by: David S. Miller --- drivers/net/usb/cdc_eem.c | 1 + 1 file changed, 1 insertion(+) diff --git a/drivers/net/usb/cdc_eem.c b/drivers/net/usb/cdc_eem.c index 439690be519f..685a4e22c768 100644 --- a/drivers/net/usb/cdc_eem.c +++ b/drivers/net/usb/cdc_eem.c @@ -93,6 +93,7 @@ static int eem_bind(struct usbnet *dev, struct usb_interface *intf) /* no jumbogram (16K) support for now */ dev->net->hard_header_len += EEM_HEAD + ETH_FCS_LEN; + dev->hard_mtu = dev->net->mtu + dev->net->hard_header_len; return 0; } -- cgit v1.2.3 From 085f1afc56619bda424941412fdeaff1e32c21dc Mon Sep 17 00:00:00 2001 From: Matt Carlson Date: Mon, 2 Apr 2012 09:01:40 +0000 Subject: tg3: Fix 5717 serdes powerdown problem If port 0 of a 5717 serdes device powers down, it hides the phy from port 1. This patch works around the problem by keeping port 0's phy powered up. Signed-off-by: Matt Carlson Signed-off-by: Michael Chan Signed-off-by: David S. Miller --- drivers/net/ethernet/broadcom/tg3.c | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) diff --git a/drivers/net/ethernet/broadcom/tg3.c b/drivers/net/ethernet/broadcom/tg3.c index 7b71387cf93c..d2ff8ee39e84 100644 --- a/drivers/net/ethernet/broadcom/tg3.c +++ b/drivers/net/ethernet/broadcom/tg3.c @@ -2779,7 +2779,9 @@ static void tg3_power_down_phy(struct tg3 *tp, bool do_low_power) if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5700 || GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5704 || (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5780 && - (tp->phy_flags & TG3_PHYFLG_MII_SERDES))) + (tp->phy_flags & TG3_PHYFLG_MII_SERDES)) || + (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5717 && + !tp->pci_fn)) return; if (GET_CHIP_REV(tp->pci_chip_rev_id) == CHIPREV_5784_AX || -- cgit v1.2.3 From 2240eb4ae3dc4acff20d1a8947c441c451513e37 Mon Sep 17 00:00:00 2001 From: Lino Sanfilippo Date: Fri, 30 Mar 2012 07:28:59 +0000 Subject: sky2: dont overwrite settings for PHY Quick link This patch corrects a bug in function sky2_open() of the Marvell Yukon 2 driver in which the settings for PHY quick link are overwritten. Signed-off-by: Lino Sanfilippo Acked-by: Stephen Hemminger Signed-off-by: David S. Miller --- drivers/net/ethernet/marvell/sky2.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-) diff --git a/drivers/net/ethernet/marvell/sky2.c b/drivers/net/ethernet/marvell/sky2.c index 423a1a2a702e..b806d9b4defb 100644 --- a/drivers/net/ethernet/marvell/sky2.c +++ b/drivers/net/ethernet/marvell/sky2.c @@ -1767,13 +1767,14 @@ static int sky2_open(struct net_device *dev) sky2_hw_up(sky2); + /* Enable interrupts from phy/mac for port */ + imask = sky2_read32(hw, B0_IMSK); + if (hw->chip_id == CHIP_ID_YUKON_OPT || hw->chip_id == CHIP_ID_YUKON_PRM || hw->chip_id == CHIP_ID_YUKON_OP_2) imask |= Y2_IS_PHY_QLNK; /* enable PHY Quick Link */ - /* Enable interrupts from phy/mac for port */ - imask = sky2_read32(hw, B0_IMSK); imask |= portirq_msk[port]; sky2_write32(hw, B0_IMSK, imask); sky2_read32(hw, B0_IMSK); -- cgit v1.2.3