From d7b461c5e82fc5f5e4261f3b0228ecda58eb9f1a Mon Sep 17 00:00:00 2001 From: Mauro Carvalho Chehab Date: Wed, 12 Jun 2019 14:52:47 -0300 Subject: docs: ide: convert docs to ReST and rename to *.rst The conversion is actually: - add blank lines and identation in order to identify paragraphs; - fix tables markups; - add some lists markups; - mark literal blocks; - adjust title markups. At its new index.rst, let's add a :orphan: while this is not linked to the main index.rst file, in order to avoid build warnings. Signed-off-by: Mauro Carvalho Chehab Acked-by: Geert Uytterhoeven Signed-off-by: Jonathan Corbet --- Documentation/ide/ide-tape.rst | 68 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 68 insertions(+) create mode 100644 Documentation/ide/ide-tape.rst (limited to 'Documentation/ide/ide-tape.rst') diff --git a/Documentation/ide/ide-tape.rst b/Documentation/ide/ide-tape.rst new file mode 100644 index 000000000000..3e061d9c0e38 --- /dev/null +++ b/Documentation/ide/ide-tape.rst @@ -0,0 +1,68 @@ +=============================== +IDE ATAPI streaming tape driver +=============================== + +This driver is a part of the Linux ide driver. + +The driver, in co-operation with ide.c, basically traverses the +request-list for the block device interface. The character device +interface, on the other hand, creates new requests, adds them +to the request-list of the block device, and waits for their completion. + +The block device major and minor numbers are determined from the +tape's relative position in the ide interfaces, as explained in ide.c. + +The character device interface consists of the following devices:: + + ht0 major 37, minor 0 first IDE tape, rewind on close. + ht1 major 37, minor 1 second IDE tape, rewind on close. + ... + nht0 major 37, minor 128 first IDE tape, no rewind on close. + nht1 major 37, minor 129 second IDE tape, no rewind on close. + ... + +The general magnetic tape commands compatible interface, as defined by +include/linux/mtio.h, is accessible through the character device. + +General ide driver configuration options, such as the interrupt-unmask +flag, can be configured by issuing an ioctl to the block device interface, +as any other ide device. + +Our own ide-tape ioctl's can be issued to either the block device or +the character device interface. + +Maximal throughput with minimal bus load will usually be achieved in the +following scenario: + + 1. ide-tape is operating in the pipelined operation mode. + 2. No buffering is performed by the user backup program. + +Testing was done with a 2 GB CONNER CTMA 4000 IDE ATAPI Streaming Tape Drive. + +Here are some words from the first releases of hd.c, which are quoted +in ide.c and apply here as well: + +* Special care is recommended. Have Fun! + +Possible improvements +===================== + +1. Support for the ATAPI overlap protocol. + +In order to maximize bus throughput, we currently use the DSC +overlap method which enables ide.c to service requests from the +other device while the tape is busy executing a command. The +DSC overlap method involves polling the tape's status register +for the DSC bit, and servicing the other device while the tape +isn't ready. + +In the current QIC development standard (December 1995), +it is recommended that new tape drives will *in addition* +implement the ATAPI overlap protocol, which is used for the +same purpose - efficient use of the IDE bus, but is interrupt +driven and thus has much less CPU overhead. + +ATAPI overlap is likely to be supported in most new ATAPI +devices, including new ATAPI cdroms, and thus provides us +a method by which we can achieve higher throughput when +sharing a (fast) ATA-2 disk with any (slow) new ATAPI device. -- cgit v1.2.3