From f21179a47ff8d1046a61c1cf5920244997a4a7bb Mon Sep 17 00:00:00 2001 From: Henrique de Moraes Holschuh Date: Sat, 30 May 2009 13:25:08 -0300 Subject: thinkpad-acpi: enhance led support Add support for extra LEDs on recent ThinkPads, and avoid registering with the led class the LEDs which are not available for a given ThinkPad model. All non-restricted LEDs are always available through the procfs interface, as the firmware doesn't care if an attempt is made to access an invalid LED. Signed-off-by: Henrique de Moraes Holschuh Signed-off-by: Len Brown --- Documentation/laptops/thinkpad-acpi.txt | 23 ++++++++++++++++++++--- 1 file changed, 20 insertions(+), 3 deletions(-) (limited to 'Documentation/laptops') diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt index e7e9a69069e1..88fc0661de56 100644 --- a/Documentation/laptops/thinkpad-acpi.txt +++ b/Documentation/laptops/thinkpad-acpi.txt @@ -920,7 +920,7 @@ The available commands are: echo ' off' >/proc/acpi/ibm/led echo ' blink' >/proc/acpi/ibm/led -The range is 0 to 7. The set of LEDs that can be +The range is 0 to 15. The set of LEDs that can be controlled varies from model to model. Here is the common ThinkPad mapping: @@ -932,6 +932,11 @@ mapping: 5 - UltraBase battery slot 6 - (unknown) 7 - standby + 8 - dock status 1 + 9 - dock status 2 + 10, 11 - (unknown) + 12 - thinkvantage + 13, 14, 15 - (unknown) All of the above can be turned on and off and can be made to blink. @@ -940,10 +945,12 @@ sysfs notes: The ThinkPad LED sysfs interface is described in detail by the LED class documentation, in Documentation/leds-class.txt. -The leds are named (in LED ID order, from 0 to 7): +The LEDs are named (in LED ID order, from 0 to 12): "tpacpi::power", "tpacpi:orange:batt", "tpacpi:green:batt", "tpacpi::dock_active", "tpacpi::bay_active", "tpacpi::dock_batt", -"tpacpi::unknown_led", "tpacpi::standby". +"tpacpi::unknown_led", "tpacpi::standby", "tpacpi::dock_status1", +"tpacpi::dock_status2", "tpacpi::unknown_led2", "tpacpi::unknown_led3", +"tpacpi::thinkvantage". Due to limitations in the sysfs LED class, if the status of the LED indicators cannot be read due to an error, thinkpad-acpi will report it as @@ -958,6 +965,12 @@ ThinkPad indicator LED should blink in hardware accelerated mode, use the "timer" trigger, and leave the delay_on and delay_off parameters set to zero (to request hardware acceleration autodetection). +LEDs that are known not to exist in a given ThinkPad model are not +made available through the sysfs interface. If you have a dock and you +notice there are LEDs listed for your ThinkPad that do not exist (and +are not in the dock), or if you notice that there are missing LEDs, +a report to ibm-acpi-devel@lists.sourceforge.net is appreciated. + ACPI sounds -- /proc/acpi/ibm/beep ---------------------------------- @@ -1555,3 +1568,7 @@ Sysfs interface changelog: 0x020300: hotkey enable/disable support removed, attributes hotkey_bios_enabled and hotkey_enable deprecated and marked for removal. + +0x020400: Marker for 16 LEDs support. Also, LEDs that are known + to not exist in a given model are not registered with + the LED sysfs class anymore. -- cgit v1.2.3 From d7880f10c5d42ba182a97c1fd41d41d0b8837097 Mon Sep 17 00:00:00 2001 From: Henrique de Moraes Holschuh Date: Thu, 18 Jun 2009 00:40:16 -0300 Subject: thinkpad-acpi: forbid the use of HBRV on Lenovo ThinkPads Forcing thinkpad-acpi to do EC-based brightness control (HBRV) on a X61 has very... interesting effects, instead of doing nothing (since it doesn't have EC-based backlight control), it causes "weirdness" in the fan tachometer readings, for example. This means the EC register that used to be HBRV has been reused by Lenovo for something else, but they didn't remove it from the DSDT. Make sure the documentation reflects this data, and forbid the user from forcing the driver to access HBRV on Lenovo ThinkPads. Signed-off-by: Henrique de Moraes Holschuh Signed-off-by: Len Brown --- Documentation/laptops/thinkpad-acpi.txt | 14 ++++++++------ drivers/platform/x86/thinkpad_acpi.c | 10 ++++++++++ 2 files changed, 18 insertions(+), 6 deletions(-) (limited to 'Documentation/laptops') diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt index 88fc0661de56..f2ff638cce8d 100644 --- a/Documentation/laptops/thinkpad-acpi.txt +++ b/Documentation/laptops/thinkpad-acpi.txt @@ -1169,17 +1169,19 @@ may not be distinct. Later Lenovo models that implement the ACPI display backlight brightness control methods have 16 levels, ranging from 0 to 15. -There are two interfaces to the firmware for direct brightness control, -EC and UCMS (or CMOS). To select which one should be used, use the -brightness_mode module parameter: brightness_mode=1 selects EC mode, -brightness_mode=2 selects UCMS mode, brightness_mode=3 selects EC -mode with NVRAM backing (so that brightness changes are remembered -across shutdown/reboot). +For IBM ThinkPads, there are two interfaces to the firmware for direct +brightness control, EC and UCMS (or CMOS). To select which one should be +used, use the brightness_mode module parameter: brightness_mode=1 selects +EC mode, brightness_mode=2 selects UCMS mode, brightness_mode=3 selects EC +mode with NVRAM backing (so that brightness changes are remembered across +shutdown/reboot). The driver tries to select which interface to use from a table of defaults for each ThinkPad model. If it makes a wrong choice, please report this as a bug, so that we can fix it. +Lenovo ThinkPads only support brightness_mode=2 (UCMS). + When display backlight brightness controls are available through the standard ACPI interface, it is best to use it instead of this direct ThinkPad-specific interface. The driver will disable its native diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c index 5a22a064222c..c8d74dbacbbd 100644 --- a/drivers/platform/x86/thinkpad_acpi.c +++ b/drivers/platform/x86/thinkpad_acpi.c @@ -5696,6 +5696,10 @@ static struct ibm_struct ecdump_driver_data = { * Bit 3-0: backlight brightness level * * brightness_get_raw returns status data in the HBRV layout + * + * WARNING: The X61 has been verified to use HBRV for something else, so + * this should be used _only_ on IBM ThinkPads, and maybe with some careful + * testing on the very early *60 Lenovo models... */ enum { @@ -5996,6 +6000,12 @@ static int __init brightness_init(struct ibm_init_struct *iibm) brightness_mode); } + /* Safety */ + if (thinkpad_id.vendor != PCI_VENDOR_ID_IBM && + (brightness_mode == TPACPI_BRGHT_MODE_ECNVRAM || + brightness_mode == TPACPI_BRGHT_MODE_EC)) + return -EINVAL; + if (tpacpi_brightness_get_raw(&b) < 0) return 1; -- cgit v1.2.3 From d73772474f6ebbacbe820c31c0fa1cffa7160246 Mon Sep 17 00:00:00 2001 From: Henrique de Moraes Holschuh Date: Thu, 18 Jun 2009 00:40:17 -0300 Subject: thinkpad-acpi: support the second fan on the X61 Support reading the tachometer of the auxiliary fan of a X60/X61. It was found out by sheer luck, that bit 0 of EC register 0x31 (formely HBRV) selects which fan is active for tachometer readings through EC 0x84/0x085: 0 for fan1, 1 for fan2. Many thanks to Christoph Kl??nter, to Whoopie, and to weasel, who helped confirm that behaviour. Fan control through EC HFSP applies to both fans equally, regardless of the state of bit 0 of EC 0x31. That matches the way the DSDT uses HFSP. In order to better support the secondary fan, export a second tachometer over hwmon, and add defensive measures to make sure we are reading the correct tachometer. Support for the second fan is whitelist-based, as I have not found anything obvious to look for in the DSDT to detect the presence of the second fan. Signed-off-by: Henrique de Moraes Holschuh Signed-off-by: Len Brown --- Documentation/laptops/thinkpad-acpi.txt | 10 ++- drivers/platform/x86/thinkpad_acpi.c | 122 +++++++++++++++++++++++++++++++- 2 files changed, 130 insertions(+), 2 deletions(-) (limited to 'Documentation/laptops') diff --git a/Documentation/laptops/thinkpad-acpi.txt b/Documentation/laptops/thinkpad-acpi.txt index f2ff638cce8d..0d5e91379ae8 100644 --- a/Documentation/laptops/thinkpad-acpi.txt +++ b/Documentation/laptops/thinkpad-acpi.txt @@ -1269,7 +1269,7 @@ Fan control and monitoring: fan speed, fan enable/disable procfs: /proc/acpi/ibm/fan sysfs device attributes: (hwmon "thinkpad") fan1_input, pwm1, - pwm1_enable + pwm1_enable, fan2_input sysfs hwmon driver attributes: fan_watchdog NOTE NOTE NOTE: fan control operations are disabled by default for @@ -1282,6 +1282,9 @@ from the hardware registers of the embedded controller. This is known to work on later R, T, X and Z series ThinkPads but may show a bogus value on other models. +Some Lenovo ThinkPads support a secondary fan. This fan cannot be +controlled separately, it shares the main fan control. + Fan levels: Most ThinkPad fans work in "levels" at the firmware interface. Level 0 @@ -1412,6 +1415,11 @@ hwmon device attribute fan1_input: which can take up to two minutes. May return rubbish on older ThinkPads. +hwmon device attribute fan2_input: + Fan tachometer reading, in RPM, for the secondary fan. + Available only on some ThinkPads. If the secondary fan is + not installed, will always read 0. + hwmon driver attribute fan_watchdog: Fan safety watchdog timer interval, in seconds. Minimum is 1 second, maximum is 120 seconds. 0 disables the watchdog. diff --git a/drivers/platform/x86/thinkpad_acpi.c b/drivers/platform/x86/thinkpad_acpi.c index c8d74dbacbbd..27ca676a7092 100644 --- a/drivers/platform/x86/thinkpad_acpi.c +++ b/drivers/platform/x86/thinkpad_acpi.c @@ -264,6 +264,7 @@ static struct { u32 wan:1; u32 uwb:1; u32 fan_ctrl_status_undef:1; + u32 second_fan:1; u32 beep_needs_two_args:1; u32 input_device_registered:1; u32 platform_drv_registered:1; @@ -6298,6 +6299,21 @@ static struct ibm_struct volume_driver_data = { * For firmware bugs, refer to: * http://thinkwiki.org/wiki/Embedded_Controller_Firmware#Firmware_Issues * + * ---- + * + * ThinkPad EC register 0x31 bit 0 (only on select models) + * + * When bit 0 of EC register 0x31 is zero, the tachometer registers + * show the speed of the main fan. When bit 0 of EC register 0x31 + * is one, the tachometer registers show the speed of the auxiliary + * fan. + * + * Fan control seems to affect both fans, regardless of the state + * of this bit. + * + * So far, only the firmware for the X60/X61 non-tablet versions + * seem to support this (firmware TP-7M). + * * TPACPI_FAN_WR_ACPI_FANS: * ThinkPad X31, X40, X41. Not available in the X60. * @@ -6324,6 +6340,8 @@ enum { /* Fan control constants */ fan_status_offset = 0x2f, /* EC register 0x2f */ fan_rpm_offset = 0x84, /* EC register 0x84: LSB, 0x85 MSB (RPM) * 0x84 must be read before 0x85 */ + fan_select_offset = 0x31, /* EC register 0x31 (Firmware 7M) + bit 0 selects which fan is active */ TP_EC_FAN_FULLSPEED = 0x40, /* EC fan mode: full speed */ TP_EC_FAN_AUTO = 0x80, /* EC fan mode: auto fan control */ @@ -6417,6 +6435,38 @@ static void fan_quirk1_handle(u8 *fan_status) } } +/* Select main fan on X60/X61, NOOP on others */ +static bool fan_select_fan1(void) +{ + if (tp_features.second_fan) { + u8 val; + + if (ec_read(fan_select_offset, &val) < 0) + return false; + val &= 0xFEU; + if (ec_write(fan_select_offset, val) < 0) + return false; + } + return true; +} + +/* Select secondary fan on X60/X61 */ +static bool fan_select_fan2(void) +{ + u8 val; + + if (!tp_features.second_fan) + return false; + + if (ec_read(fan_select_offset, &val) < 0) + return false; + val |= 0x01U; + if (ec_write(fan_select_offset, val) < 0) + return false; + + return true; +} + /* * Call with fan_mutex held */ @@ -6494,6 +6544,8 @@ static int fan_get_speed(unsigned int *speed) switch (fan_status_access_mode) { case TPACPI_FAN_RD_TPEC: /* all except 570, 600e/x, 770e, 770x */ + if (unlikely(!fan_select_fan1())) + return -EIO; if (unlikely(!acpi_ec_read(fan_rpm_offset, &lo) || !acpi_ec_read(fan_rpm_offset + 1, &hi))) return -EIO; @@ -6510,6 +6562,34 @@ static int fan_get_speed(unsigned int *speed) return 0; } +static int fan2_get_speed(unsigned int *speed) +{ + u8 hi, lo; + bool rc; + + switch (fan_status_access_mode) { + case TPACPI_FAN_RD_TPEC: + /* all except 570, 600e/x, 770e, 770x */ + if (unlikely(!fan_select_fan2())) + return -EIO; + rc = !acpi_ec_read(fan_rpm_offset, &lo) || + !acpi_ec_read(fan_rpm_offset + 1, &hi); + fan_select_fan1(); /* play it safe */ + if (rc) + return -EIO; + + if (likely(speed)) + *speed = (hi << 8) | lo; + + break; + + default: + return -ENXIO; + } + + return 0; +} + static int fan_set_level(int level) { if (!fan_control_allowed) @@ -6915,6 +6995,25 @@ static struct device_attribute dev_attr_fan_fan1_input = __ATTR(fan1_input, S_IRUGO, fan_fan1_input_show, NULL); +/* sysfs fan fan2_input ------------------------------------------------ */ +static ssize_t fan_fan2_input_show(struct device *dev, + struct device_attribute *attr, + char *buf) +{ + int res; + unsigned int speed; + + res = fan2_get_speed(&speed); + if (res < 0) + return res; + + return snprintf(buf, PAGE_SIZE, "%u\n", speed); +} + +static struct device_attribute dev_attr_fan_fan2_input = + __ATTR(fan2_input, S_IRUGO, + fan_fan2_input_show, NULL); + /* sysfs fan fan_watchdog (hwmon driver) ------------------------------- */ static ssize_t fan_fan_watchdog_show(struct device_driver *drv, char *buf) @@ -6948,6 +7047,7 @@ static DRIVER_ATTR(fan_watchdog, S_IWUSR | S_IRUGO, static struct attribute *fan_attributes[] = { &dev_attr_fan_pwm1_enable.attr, &dev_attr_fan_pwm1.attr, &dev_attr_fan_fan1_input.attr, + NULL, /* for fan2_input */ NULL }; @@ -6955,7 +7055,8 @@ static const struct attribute_group fan_attr_group = { .attrs = fan_attributes, }; -#define TPACPI_FAN_Q1 0x0001 +#define TPACPI_FAN_Q1 0x0001 /* Unitialized HFSP */ +#define TPACPI_FAN_2FAN 0x0002 /* EC 0x31 bit 0 selects fan2 */ #define TPACPI_FAN_QI(__id1, __id2, __quirks) \ { .vendor = PCI_VENDOR_ID_IBM, \ @@ -6963,13 +7064,21 @@ static const struct attribute_group fan_attr_group = { .ec = TPID(__id1, __id2), \ .quirks = __quirks } +#define TPACPI_FAN_QL(__id1, __id2, __quirks) \ + { .vendor = PCI_VENDOR_ID_LENOVO, \ + .bios = TPACPI_MATCH_ANY, \ + .ec = TPID(__id1, __id2), \ + .quirks = __quirks } + static const struct tpacpi_quirk fan_quirk_table[] __initconst = { TPACPI_FAN_QI('1', 'Y', TPACPI_FAN_Q1), TPACPI_FAN_QI('7', '8', TPACPI_FAN_Q1), TPACPI_FAN_QI('7', '6', TPACPI_FAN_Q1), TPACPI_FAN_QI('7', '0', TPACPI_FAN_Q1), + TPACPI_FAN_QL('7', 'M', TPACPI_FAN_2FAN), }; +#undef TPACPI_FAN_QL #undef TPACPI_FAN_QI static int __init fan_init(struct ibm_init_struct *iibm) @@ -6986,6 +7095,7 @@ static int __init fan_init(struct ibm_init_struct *iibm) fan_control_commands = 0; fan_watchdog_maxinterval = 0; tp_features.fan_ctrl_status_undef = 0; + tp_features.second_fan = 0; fan_control_desired_level = 7; TPACPI_ACPIHANDLE_INIT(fans); @@ -7006,6 +7116,11 @@ static int __init fan_init(struct ibm_init_struct *iibm) fan_status_access_mode = TPACPI_FAN_RD_TPEC; if (quirks & TPACPI_FAN_Q1) fan_quirk1_setup(); + if (quirks & TPACPI_FAN_2FAN) { + tp_features.second_fan = 1; + dbg_printk(TPACPI_DBG_INIT | TPACPI_DBG_FAN, + "secondary fan support enabled\n"); + } } else { printk(TPACPI_ERR "ThinkPad ACPI EC access misbehaving, " @@ -7061,6 +7176,11 @@ static int __init fan_init(struct ibm_init_struct *iibm) if (fan_status_access_mode != TPACPI_FAN_NONE || fan_control_access_mode != TPACPI_FAN_WR_NONE) { + if (tp_features.second_fan) { + /* attach second fan tachometer */ + fan_attributes[ARRAY_SIZE(fan_attributes)-2] = + &dev_attr_fan_fan2_input.attr; + } rc = sysfs_create_group(&tpacpi_sensors_pdev->dev.kobj, &fan_attr_group); if (rc < 0) -- cgit v1.2.3