From 1da177e4c3f41524e886b7f1b8a0c1fc7321cac2 Mon Sep 17 00:00:00 2001 From: Linus Torvalds Date: Sat, 16 Apr 2005 15:20:36 -0700 Subject: Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! --- Documentation/networking/dl2k.txt | 281 ++++++++++++++++++++++++++++++++++++++ 1 file changed, 281 insertions(+) create mode 100644 Documentation/networking/dl2k.txt (limited to 'Documentation/networking/dl2k.txt') diff --git a/Documentation/networking/dl2k.txt b/Documentation/networking/dl2k.txt new file mode 100644 index 000000000000..d460492037ef --- /dev/null +++ b/Documentation/networking/dl2k.txt @@ -0,0 +1,281 @@ + + D-Link DL2000-based Gigabit Ethernet Adapter Installation + for Linux + May 23, 2002 + +Contents +======== + - Compatibility List + - Quick Install + - Compiling the Driver + - Installing the Driver + - Option parameter + - Configuration Script Sample + - Troubleshooting + + +Compatibility List +================= +Adapter Support: + +D-Link DGE-550T Gigabit Ethernet Adapter. +D-Link DGE-550SX Gigabit Ethernet Adapter. +D-Link DL2000-based Gigabit Ethernet Adapter. + + +The driver support Linux kernel 2.4.7 later. We had tested it +on the environments below. + + . Red Hat v6.2 (update kernel to 2.4.7) + . Red Hat v7.0 (update kernel to 2.4.7) + . Red Hat v7.1 (kernel 2.4.7) + . Red Hat v7.2 (kernel 2.4.7-10) + + +Quick Install +============= +Install linux driver as following command: + +1. make all +2. insmod dl2k.ko +3. ifconfig eth0 up 10.xxx.xxx.xxx netmask 255.0.0.0 + ^^^^^^^^^^^^^^^\ ^^^^^^^^\ + IP NETMASK +Now eth0 should active, you can test it by "ping" or get more information by +"ifconfig". If tested ok, continue the next step. + +4. cp dl2k.ko /lib/modules/`uname -r`/kernel/drivers/net +5. Add the following line to /etc/modprobe.conf: + alias eth0 dl2k +6. Run "netconfig" or "netconf" to create configuration script ifcfg-eth0 + located at /etc/sysconfig/network-scripts or create it manually. + [see - Configuration Script Sample] +7. Driver will automatically load and configure at next boot time. + +Compiling the Driver +==================== + In Linux, NIC drivers are most commonly configured as loadable modules. +The approach of building a monolithic kernel has become obsolete. The driver +can be compiled as part of a monolithic kernel, but is strongly discouraged. +The remainder of this section assumes the driver is built as a loadable module. +In the Linux environment, it is a good idea to rebuild the driver from the +source instead of relying on a precompiled version. This approach provides +better reliability since a precompiled driver might depend on libraries or +kernel features that are not present in a given Linux installation. + +The 3 files necessary to build Linux device driver are dl2k.c, dl2k.h and +Makefile. To compile, the Linux installation must include the gcc compiler, +the kernel source, and the kernel headers. The Linux driver supports Linux +Kernels 2.4.7. Copy the files to a directory and enter the following command +to compile and link the driver: + +CD-ROM drive +------------ + +[root@XXX /] mkdir cdrom +[root@XXX /] mount -r -t iso9660 -o conv=auto /dev/cdrom /cdrom +[root@XXX /] cd root +[root@XXX /root] mkdir dl2k +[root@XXX /root] cd dl2k +[root@XXX dl2k] cp /cdrom/linux/dl2k.tgz /root/dl2k +[root@XXX dl2k] tar xfvz dl2k.tgz +[root@XXX dl2k] make all + +Floppy disc drive +----------------- + +[root@XXX /] cd root +[root@XXX /root] mkdir dl2k +[root@XXX /root] cd dl2k +[root@XXX dl2k] mcopy a:/linux/dl2k.tgz /root/dl2k +[root@XXX dl2k] tar xfvz dl2k.tgz +[root@XXX dl2k] make all + +Installing the Driver +===================== + + Manual Installation + ------------------- + Once the driver has been compiled, it must be loaded, enabled, and bound + to a protocol stack in order to establish network connectivity. To load a + module enter the command: + + insmod dl2k.o + + or + + insmod dl2k.o ; add parameter + + =============================================================== + example: insmod dl2k.o media=100mbps_hd + or insmod dl2k.o media=3 + or insmod dl2k.o media=3,2 ; for 2 cards + =============================================================== + + Please reference the list of the command line parameters supported by + the Linux device driver below. + + The insmod command only loads the driver and gives it a name of the form + eth0, eth1, etc. To bring the NIC into an operational state, + it is necessary to issue the following command: + + ifconfig eth0 up + + Finally, to bind the driver to the active protocol (e.g., TCP/IP with + Linux), enter the following command: + + ifup eth0 + + Note that this is meaningful only if the system can find a configuration + script that contains the necessary network information. A sample will be + given in the next paragraph. + + The commands to unload a driver are as follows: + + ifdown eth0 + ifconfig eth0 down + rmmod dl2k.o + + The following are the commands to list the currently loaded modules and + to see the current network configuration. + + lsmod + ifconfig + + + Automated Installation + ---------------------- + This section describes how to install the driver such that it is + automatically loaded and configured at boot time. The following description + is based on a Red Hat 6.0/7.0 distribution, but it can easily be ported to + other distributions as well. + + Red Hat v6.x/v7.x + ----------------- + 1. Copy dl2k.o to the network modules directory, typically + /lib/modules/2.x.x-xx/net or /lib/modules/2.x.x/kernel/drivers/net. + 2. Locate the boot module configuration file, most commonly modprobe.conf + or modules.conf (for 2.4) in the /etc directory. Add the following lines: + + alias ethx dl2k + options dl2k + + where ethx will be eth0 if the NIC is the only ethernet adapter, eth1 if + one other ethernet adapter is installed, etc. Refer to the table in the + previous section for the list of optional parameters. + 3. Locate the network configuration scripts, normally the + /etc/sysconfig/network-scripts directory, and create a configuration + script named ifcfg-ethx that contains network information. + 4. Note that for most Linux distributions, Red Hat included, a configuration + utility with a graphical user interface is provided to perform steps 2 + and 3 above. + + +Parameter Description +===================== +You can install this driver without any addtional parameter. However, if you +are going to have extensive functions then it is necessary to set extra +parameter. Below is a list of the command line parameters supported by the +Linux device +driver. + +mtu=packet_size - Specifies the maximum packet size. default + is 1500. + +media=media_type - Specifies the media type the NIC operates at. + autosense Autosensing active media. + 10mbps_hd 10Mbps half duplex. + 10mbps_fd 10Mbps full duplex. + 100mbps_hd 100Mbps half duplex. + 100mbps_fd 100Mbps full duplex. + 1000mbps_fd 1000Mbps full duplex. + 1000mbps_hd 1000Mbps half duplex. + 0 Autosensing active media. + 1 10Mbps half duplex. + 2 10Mbps full duplex. + 3 100Mbps half duplex. + 4 100Mbps full duplex. + 5 1000Mbps half duplex. + 6 1000Mbps full duplex. + + By default, the NIC operates at autosense. + 1000mbps_fd and 1000mbps_hd types are only + available for fiber adapter. + +vlan=n - Specifies the VLAN ID. If vlan=0, the + Virtual Local Area Network (VLAN) function is + disable. + +jumbo=[0|1] - Specifies the jumbo frame support. If jumbo=1, + the NIC accept jumbo frames. By default, this + function is disabled. + Jumbo frame usually improve the performance + int gigabit. + This feature need jumbo frame compatible + remote. + +rx_coalesce=m - Number of rx frame handled each interrupt. +rx_timeout=n - Rx DMA wait time for an interrupt. + If set rx_coalesce > 0, hardware only assert + an interrupt for m frames. Hardware won't + assert rx interrupt until m frames received or + reach timeout of n * 640 nano seconds. + Set proper rx_coalesce and rx_timeout can + reduce congestion collapse and overload which + has been a bottlenect for high speed network. + + For example, rx_coalesce=10 rx_timeout=800. + that is, hardware assert only 1 interrupt + for 10 frames received or timeout of 512 us. + +tx_coalesce=n - Number of tx frame handled each interrupt. + Set n > 1 can reduce the interrupts + congestion usually lower performance of + high speed network card. Default is 16. + +tx_flow=[1|0] - Specifies the Tx flow control. If tx_flow=0, + the Tx flow control disable else driver + autodetect. +rx_flow=[1|0] - Specifies the Rx flow control. If rx_flow=0, + the Rx flow control enable else driver + autodetect. + + +Configuration Script Sample +=========================== +Here is a sample of a simple configuration script: + +DEVICE=eth0 +USERCTL=no +ONBOOT=yes +POOTPROTO=none +BROADCAST=207.200.5.255 +NETWORK=207.200.5.0 +NETMASK=255.255.255.0 +IPADDR=207.200.5.2 + + +Troubleshooting +=============== +Q1. Source files contain ^ M behind every line. + Make sure all files are Unix file format (no LF). Try the following + shell command to convert files. + + cat dl2k.c | col -b > dl2k.tmp + mv dl2k.tmp dl2k.c + + OR + + cat dl2k.c | tr -d "\r" > dl2k.tmp + mv dl2k.tmp dl2k.c + +Q2: Could not find header files (*.h) ? + To compile the driver, you need kernel header files. After + installing the kernel source, the header files are usually located in + /usr/src/linux/include, which is the default include directory configured + in Makefile. For some distributions, there is a copy of header files in + /usr/src/include/linux and /usr/src/include/asm, that you can change the + INCLUDEDIR in Makefile to /usr/include without installing kernel source. + Note that RH 7.0 didn't provide correct header files in /usr/include, + including those files will make a wrong version driver. + -- cgit v1.2.3