From b5896f67ab3cf881a40d4ae9837bb32ec261f4c3 Mon Sep 17 00:00:00 2001 From: Marcel Ziswiler Date: Thu, 30 Jun 2016 00:21:37 +0200 Subject: ARM: tegra: Remove commas from unit addresses on Tegra124 Remove commas from unit addresses as suggested by Rob Herring upon me posting initial Apalis TK1 support: http://article.gmane.org/gmane.linux.ports.tegra/26608 Please keep the remaining 0, notation on the GPU node in place as a former mainline U-Boot version was looking for that particular notation in order to perform required fix-ups on it. Signed-off-by: Marcel Ziswiler Acked-by: Stephen Warren Tested-by: Alexandre Courbot Signed-off-by: Thierry Reding --- arch/arm/boot/dts/tegra124-nyan.dtsi | 60 ++++++++++++++++++------------------ 1 file changed, 30 insertions(+), 30 deletions(-) (limited to 'arch/arm/boot/dts/tegra124-nyan.dtsi') diff --git a/arch/arm/boot/dts/tegra124-nyan.dtsi b/arch/arm/boot/dts/tegra124-nyan.dtsi index 0710a600cc69..271505e0715f 100644 --- a/arch/arm/boot/dts/tegra124-nyan.dtsi +++ b/arch/arm/boot/dts/tegra124-nyan.dtsi @@ -3,8 +3,8 @@ / { aliases { - rtc0 = "/i2c@0,7000d000/pmic@40"; - rtc1 = "/rtc@0,7000e000"; + rtc0 = "/i2c@7000d000/pmic@40"; + rtc1 = "/rtc@7000e000"; serial0 = &uarta; }; @@ -16,8 +16,8 @@ reg = <0x0 0x80000000 0x0 0x80000000>; }; - host1x@0,50000000 { - hdmi@0,54280000 { + host1x@50000000 { + hdmi@54280000 { status = "okay"; vdd-supply = <&vdd_3v3_hdmi>; @@ -29,29 +29,29 @@ <&gpio TEGRA_GPIO(N, 7) GPIO_ACTIVE_HIGH>; }; - sor@0,54540000 { + sor@54540000 { status = "okay"; nvidia,dpaux = <&dpaux>; nvidia,panel = <&panel>; }; - dpaux@0,545c0000 { + dpaux@545c0000 { vdd-supply = <&vdd_3v3_panel>; status = "okay"; }; }; - serial@0,70006000 { + serial@70006000 { /* Debug connector on the bottom of the board near SD card. */ status = "okay"; }; - pwm@0,7000a000 { + pwm@7000a000 { status = "okay"; }; - i2c@0,7000c000 { + i2c@7000c000 { status = "okay"; clock-frequency = <100000>; @@ -72,7 +72,7 @@ }; }; - i2c@0,7000c400 { + i2c@7000c400 { status = "okay"; clock-frequency = <100000>; @@ -85,7 +85,7 @@ }; }; - i2c@0,7000c500 { + i2c@7000c500 { status = "okay"; clock-frequency = <400000>; @@ -95,12 +95,12 @@ }; }; - hdmi_ddc: i2c@0,7000c700 { + hdmi_ddc: i2c@7000c700 { status = "okay"; clock-frequency = <100000>; }; - i2c@0,7000d000 { + i2c@7000d000 { status = "okay"; clock-frequency = <400000>; @@ -301,7 +301,7 @@ }; }; - spi@0,7000d400 { + spi@7000d400 { status = "okay"; cros_ec: cros-ec@0 { @@ -342,7 +342,7 @@ }; }; - spi@0,7000da00 { + spi@7000da00 { status = "okay"; spi-max-frequency = <25000000>; @@ -353,7 +353,7 @@ }; }; - pmc@0,7000e400 { + pmc@7000e400 { nvidia,invert-interrupt; nvidia,suspend-mode = <0>; nvidia,cpu-pwr-good-time = <500>; @@ -364,16 +364,16 @@ nvidia,sys-clock-req-active-high; }; - hda@0,70030000 { + hda@70030000 { status = "okay"; }; - usb@0,70090000 { - phys = <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-0}>, /* 1st USB A */ - <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-1}>, /* Internal USB */ - <&{/padctl@0,7009f000/pads/usb2/lanes/usb2-2}>, /* 2nd USB A */ - <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-0}>, /* 1st USB A */ - <&{/padctl@0,7009f000/pads/pcie/lanes/pcie-1}>; /* 2nd USB A */ + usb@70090000 { + phys = <&{/padctl@7009f000/pads/usb2/lanes/usb2-0}>, /* 1st USB A */ + <&{/padctl@7009f000/pads/usb2/lanes/usb2-1}>, /* Internal USB */ + <&{/padctl@7009f000/pads/usb2/lanes/usb2-2}>, /* 2nd USB A */ + <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>, /* 1st USB A */ + <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>; /* 2nd USB A */ phy-names = "usb2-0", "usb2-1", "usb2-2", "usb3-0", "usb3-1"; avddio-pex-supply = <&vdd_1v05_run>; @@ -388,7 +388,7 @@ status = "okay"; }; - padctl@0,7009f000 { + padctl@7009f000 { status = "okay"; pads { @@ -467,7 +467,7 @@ reset-gpios = <&gpio TEGRA_GPIO(X, 7) GPIO_ACTIVE_LOW>; }; - sdhci@0,700b0000 { /* WiFi/BT on this bus */ + sdhci@700b0000 { /* WiFi/BT on this bus */ status = "okay"; bus-width = <4>; no-1-8-v; @@ -478,7 +478,7 @@ keep-power-in-suspend; }; - sdhci@0,700b0400 { /* SD Card on this bus */ + sdhci@700b0400 { /* SD Card on this bus */ status = "okay"; cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_LOW>; power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; @@ -487,7 +487,7 @@ vqmmc-supply = <&vddio_sdmmc3>; }; - sdhci@0,700b0600 { /* eMMC on this bus */ + sdhci@700b0600 { /* eMMC on this bus */ status = "okay"; bus-width = <8>; no-1-8-v; @@ -495,14 +495,14 @@ }; /* CPU DFLL clock */ - clock@0,70110000 { + clock@70110000 { status = "disabled"; vdd-cpu-supply = <&vdd_cpu>; nvidia,i2c-fs-rate = <400000>; }; - ahub@0,70300000 { - i2s@0,70301100 { + ahub@70300000 { + i2s@70301100 { status = "okay"; }; }; -- cgit v1.2.3