From d44cbb1e9ca3488b5f144a3a71aa58f09b5422a1 Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Thu, 9 Jun 2016 22:45:11 -0500 Subject: Revert "Revert "dts: msm8974: Add blsp2_bam dma node"" This puts back in place the blsp2_bam node. This can be safely added due to the addition of the special qcom,controlled-remotely flag that will be used on specific boards that require it. This reverts commit 338d51889851cb2ac900d2ec75c8185afcde8caf. --- arch/arm/boot/dts/qcom-msm8974.dtsi | 12 +++++++++++- 1 file changed, 11 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index 6f164266a010..320564c8554b 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -1,6 +1,6 @@ /dts-v1/; -#include +#include #include #include "skeleton.dtsi" @@ -518,6 +518,16 @@ interrupt-controller; #interrupt-cells = <4>; }; + + blsp2_dma: dma-controller@f9944000 { + compatible = "qcom,bam-v1.4.0"; + reg = <0xf9944000 0x19000>; + interrupts = ; + clocks = <&gcc GCC_BLSP2_AHB_CLK>; + clock-names = "bam_clk"; + #dma-cells = <1>; + qcom,ee = <0>; + }; }; smd { -- cgit v1.2.3 From 938b4d4ea13535d99e6b7bc145b78171bdea7da4 Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Thu, 9 Jun 2016 22:45:27 -0500 Subject: Revert "Revert "dts: msm8974: Add dma channels for blsp2_i2c1 node"" This adds back the dma channels for the i2c1 node. This is safe now that the qcom,controlled-remotely changes are in place and will be used on the boards that require it. This reverts commit 10c0f0e92f019ab8d0c17da3696e35b0eef4ec16. --- arch/arm/boot/dts/qcom-msm8974.dtsi | 2 ++ 1 file changed, 2 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index 320564c8554b..e98b3738ee42 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -501,6 +501,8 @@ clock-names = "core", "iface"; #address-cells = <1>; #size-cells = <0>; + dmas = <&blsp2_dma 20>, <&blsp2_dma 21>; + dma-names = "tx", "rx"; }; spmi_bus: spmi@fc4cf000 { -- cgit v1.2.3 From d04dc9521c8c929b8a3803ffc24726f150f936ea Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Tue, 10 May 2016 15:45:58 -0700 Subject: ARM: dts: qcom: Enable RPM regulators on apq8074 dragonboard Add the appropriate min/max voltages for the regulators on the apq8074 dragonboard so that they can be used by clients properly. Signed-off-by: Stephen Boyd Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8074-dragonboard.dts | 199 +++++++++++++++++++++++++ 1 file changed, 199 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts index c0e205315042..8d1011d289bc 100644 --- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts +++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts @@ -75,4 +75,203 @@ }; }; }; + + smd { + rpm { + rpm_requests { + pm8841-regulators { + s1 { + regulator-min-microvolt = <675000>; + regulator-max-microvolt = <1050000>; + }; + + s2 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1050000>; + }; + + s3 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1050000>; + }; + + s4 { + regulator-min-microvolt = <500000>; + regulator-max-microvolt = <1050000>; + }; + }; + + pm8941-regulators { + vdd_l1_l3-supply = <&pm8941_s1>; + vdd_l2_lvs1_2_3-supply = <&pm8941_s3>; + vdd_l4_l11-supply = <&pm8941_s1>; + vdd_l5_l7-supply = <&pm8941_s2>; + vdd_l6_l12_l14_l15-supply = <&pm8941_s2>; + vin_5vs-supply = <&pm8941_5v>; + + s1 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + s2 { + regulator-min-microvolt = <2150000>; + regulator-max-microvolt = <2150000>; + regulator-boot-on; + }; + + s3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + + l1 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + + regulator-always-on; + regulator-boot-on; + }; + + l2 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + l3 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l4 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + }; + + l5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-boot-on; + }; + + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-boot-on; + }; + + l8 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + }; + + l10 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + l11 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + }; + + l12 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + + regulator-always-on; + regulator-boot-on; + }; + + l13 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2950000>; + + regulator-boot-on; + }; + + l14 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + l15 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + }; + + l16 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + l17 { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + }; + + l18 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + + l19 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + l20 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + + regulator-allow-set-load; + regulator-boot-on; + regulator-system-load = <200000>; + }; + + l21 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + + regulator-boot-on; + }; + + l22 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + l23 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + l24 { + regulator-min-microvolt = <3075000>; + regulator-max-microvolt = <3075000>; + + regulator-boot-on; + }; + }; + }; + }; + }; }; -- cgit v1.2.3 From 5fda09b809c20080f5194199bdb6012b774b393e Mon Sep 17 00:00:00 2001 From: Stephen Boyd Date: Tue, 10 May 2016 15:45:59 -0700 Subject: ARM: dts: qcom: Enable sdcard and emmc on apq8074 dragonboard Enable the sdcard slot and wire up the regulators for the two storage controllers found on the apq8074 dragonboard. Signed-off-by: Stephen Boyd Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8074-dragonboard.dts | 48 ++++++++++++++++++++++++++ 1 file changed, 48 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts index 8d1011d289bc..ad51df27dfb7 100644 --- a/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts +++ b/arch/arm/boot/dts/qcom-apq8074-dragonboard.dts @@ -25,11 +25,23 @@ bus-width = <8>; non-removable; status = "ok"; + + vmmc-supply = <&pm8941_l20>; + vqmmc-supply = <&pm8941_s3>; + + pinctrl-names = "default"; + pinctrl-0 = <&sdhc1_pin_a>; }; sdhci@f98a4900 { cd-gpios = <&msmgpio 62 0x1>; + pinctrl-names = "default"; + pinctrl-0 = <&sdhc2_pin_a>, <&sdhc2_cd_pin_a>; bus-width = <4>; + status = "ok"; + + vmmc-supply = <&pm8941_l21>; + vqmmc-supply = <&pm8941_l13>; }; @@ -59,6 +71,42 @@ function = "blsp_spi8"; }; }; + + sdhc1_pin_a: sdhc1-pin-active { + clk { + pins = "sdc1_clk"; + drive-strength = <16>; + bias-disable; + }; + + cmd-data { + pins = "sdc1_cmd", "sdc1_data"; + drive-strength = <10>; + bias-pull-up; + }; + }; + + sdhc2_cd_pin_a: sdhc2-cd-pin-active { + pins = "gpio62"; + function = "gpio"; + + drive-strength = <2>; + bias-disable; + }; + + sdhc2_pin_a: sdhc2-pin-active { + clk { + pins = "sdc2_clk"; + drive-strength = <10>; + bias-disable; + }; + + cmd-data { + pins = "sdc2_cmd", "sdc2_data"; + drive-strength = <6>; + bias-pull-up; + }; + }; }; i2c@f9967000 { -- cgit v1.2.3 From a537b8d68e0b6b67ee370f9710c94bfb813b3612 Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Thu, 19 May 2016 00:00:19 -0500 Subject: ARM: dts: qcom: Remove size elements from pmic reg The #size-cells for the pmics are 0, but we specify a size in the reg property so that MPP and GPIO modules can figure out how many pins there are. Now that we've done that by counting irqs, we can remove the size elements in the reg properties and be DT compliant. Signed-off-by: Andy Gross Reviewed-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-pma8084.dtsi | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom-pma8084.dtsi index 4e9bd3f88473..ea7fce389035 100644 --- a/arch/arm/boot/dts/qcom-pma8084.dtsi +++ b/arch/arm/boot/dts/qcom-pma8084.dtsi @@ -12,15 +12,15 @@ rtc@6000 { compatible = "qcom,pm8941-rtc"; - reg = <0x6000 0x100>, - <0x6100 0x100>; + reg = <0x6000>, + <0x6100>; reg-names = "rtc", "alarm"; interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; }; pma8084_gpios: gpios@c000 { compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio"; - reg = <0xc000 0x1600>; + reg = <0xc000>; gpio-controller; #gpio-cells = <2>; interrupts = <0 0xc0 0 IRQ_TYPE_NONE>, @@ -49,7 +49,7 @@ pma8084_mpps: mpps@a000 { compatible = "qcom,pma8084-mpp", "qcom,spmi-mpp"; - reg = <0xa000 0x800>; + reg = <0xa000>; gpio-controller; #gpio-cells = <2>; interrupts = <0 0xa0 0 IRQ_TYPE_NONE>, @@ -64,7 +64,7 @@ pma8084_temp: temp-alarm@2400 { compatible = "qcom,spmi-temp-alarm"; - reg = <0x2400 0x100>; + reg = <0x2400>; interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; #thermal-sensor-cells = <0>; io-channels = <&pma8084_vadc VADC_DIE_TEMP>; @@ -73,7 +73,7 @@ pma8084_vadc: vadc@3100 { compatible = "qcom,spmi-vadc"; - reg = <0x3100 0x100>; + reg = <0x3100>; interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; #address-cells = <1>; #size-cells = <0>; -- cgit v1.2.3 From 71c0ed72170dc7589592a26a821c766bd4ba4c05 Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Thu, 19 May 2016 00:00:20 -0500 Subject: ARM: dts: qcom: pma8084: Add pwrkey entry This patch adds the power key device tree node. Signed-off-by: Andy Gross Reviewed-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-pma8084.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-pma8084.dtsi b/arch/arm/boot/dts/qcom-pma8084.dtsi index ea7fce389035..82d258094156 100644 --- a/arch/arm/boot/dts/qcom-pma8084.dtsi +++ b/arch/arm/boot/dts/qcom-pma8084.dtsi @@ -18,6 +18,14 @@ interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>; }; + pwrkey@800 { + compatible = "qcom,pm8941-pwrkey"; + reg = <0x800>; + interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>; + debounce = <15625>; + bias-pull-up; + }; + pma8084_gpios: gpios@c000 { compatible = "qcom,pma8084-gpio", "qcom,spmi-gpio"; reg = <0xc000>; -- cgit v1.2.3 From 2b9b54666caba3a7d9f47c73f4dac22baa292a62 Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Fri, 3 Jun 2016 18:25:27 -0500 Subject: dts: qcom: apq8084: Add SCM firmware node This patch adds the firmware node for the SCM Acked-by: Bjorn Andersson Signed-off-by: Andy Gross Reviewed-by: Stephen Boyd --- arch/arm/boot/dts/qcom-apq8084.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-apq8084.dtsi b/arch/arm/boot/dts/qcom-apq8084.dtsi index a33a09f6821e..7c2df062a025 100644 --- a/arch/arm/boot/dts/qcom-apq8084.dtsi +++ b/arch/arm/boot/dts/qcom-apq8084.dtsi @@ -86,6 +86,14 @@ }; }; + firmware { + scm { + compatible = "qcom,scm"; + clocks = <&gcc GCC_CE1_CLK> , <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>; + clock-names = "core", "bus", "iface"; + }; + }; + cpu-pmu { compatible = "qcom,krait-pmu"; interrupts = <1 7 0xf04>; -- cgit v1.2.3 From e0e7da5dfd37413a94c00a279a4cfd9712511675 Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Fri, 3 Jun 2016 18:25:29 -0500 Subject: dts: qcom: msm8974: Add SCM firmware node This patch adds the Qualcomm SCM firmware node. Signed-off-by: Andy Gross Reviewed-by: Stephen Boyd --- arch/arm/boot/dts/qcom-msm8974.dtsi | 8 ++++++++ 1 file changed, 8 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index e98b3738ee42..55328d6879fb 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -260,6 +260,14 @@ }; }; + firmware { + scm { + compatible = "qcom,scm"; + clocks = <&gcc GCC_CE1_CLK>, <&gcc GCC_CE1_AXI_CLK>, <&gcc GCC_CE1_AHB_CLK>; + clock-names = "core", "bus", "iface"; + }; + }; + soc: soc { #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From 9e5d41d44018bc721329e8314259d4c7f683b7c6 Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Fri, 3 Jun 2016 18:25:30 -0500 Subject: dts: qcom: apq8064: Add SCM firmware node This patch adds the firmware node for the APQ8064 Signed-off-by: Andy Gross Reviewed-by: Stephen Boyd --- arch/arm/boot/dts/qcom-apq8064.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index df96ccdc9bb4..cf37d55f6e74 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -213,6 +213,12 @@ }; }; + firmware { + scm { + compatible = "qcom,scm-apq8064"; + }; + }; + soc: soc { #address-cells = <1>; #size-cells = <1>; -- cgit v1.2.3 From ccd140b574e28a8f622fa53d8bac99e585d7ced6 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Fri, 10 Jun 2016 10:38:34 +0100 Subject: ARM: dts: apq8064: move sdcc1 pinctrl nodes to soc file This patch moves out the sdcc1 pinctrl nodes out of board files to soc file, so that it will be duplicated in other board files. Signed-off-by: Srinivas Kandagatla Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064-pins.dtsi | 20 ++++++++++++++++++++ .../arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts | 22 ---------------------- arch/arm/boot/dts/qcom-apq8064.dtsi | 2 ++ 3 files changed, 22 insertions(+), 22 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi index 4102a98f475b..ca683e56b887 100644 --- a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi @@ -7,6 +7,26 @@ }; }; + sdcc1_pins: sdcc1-pin-active { + clk { + pins = "sdc1_clk"; + drive-strengh = <16>; + bias-disable; + }; + + cmd { + pins = "sdc1_cmd"; + drive-strengh = <10>; + bias-pull-up; + }; + + data { + pins = "sdc1_data"; + drive-strengh = <10>; + bias-pull-up; + }; + }; + ps_hold: ps_hold { mux { pins = "gpio78"; diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts index 06b3c76c3e41..93d08b9a77c9 100644 --- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts +++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts @@ -70,25 +70,6 @@ }; }; - sdcc1_pin_a: sdcc1-pin-active { - clk { - pins = "sdc1_clk"; - drive-strengh = <16>; - bias-disable; - }; - - cmd { - pins = "sdc1_cmd"; - drive-strengh = <10>; - bias-pull-up; - }; - - data { - pins = "sdc1_data"; - drive-strengh = <10>; - bias-pull-up; - }; - }; sdcc3_pin_a: sdcc3-pin-active { clk { @@ -417,9 +398,6 @@ vmmc-supply = <&pm8921_l5>; vqmmc-supply = <&pm8921_s4>; - - pinctrl-names = "default"; - pinctrl-0 = <&sdcc1_pin_a>; }; sdcc3: sdcc@12180000 { diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index cf37d55f6e74..ce7ce846615e 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -859,6 +859,8 @@ sdcc1: sdcc@12400000 { status = "disabled"; compatible = "arm,pl18x", "arm,primecell"; + pinctrl-names = "default"; + pinctrl-0 = <&sdcc1_pins>; arm,primecell-periphid = <0x00051180>; reg = <0x12400000 0x2000>; interrupts = ; -- cgit v1.2.3 From c351c254ac676d79282512d2f692ab0ccce479a6 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Fri, 10 Jun 2016 10:38:35 +0100 Subject: ARM: dts: apq8064: move sdcc3 pinctrls out of baord file This patch move sdcc3 pinctrl nodes out of board file, so that other boards do not duplicate the same thing. Signed-off-by: Srinivas Kandagatla Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064-pins.dtsi | 20 ++++++++++++++++++++ .../arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts | 22 +--------------------- 2 files changed, 21 insertions(+), 21 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi index ca683e56b887..6b801e7e57a2 100644 --- a/arch/arm/boot/dts/qcom-apq8064-pins.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064-pins.dtsi @@ -27,6 +27,26 @@ }; }; + sdcc3_pins: sdcc3-pin-active { + clk { + pins = "sdc3_clk"; + drive-strengh = <8>; + bias-disable; + }; + + cmd { + pins = "sdc3_cmd"; + drive-strengh = <8>; + bias-pull-up; + }; + + data { + pins = "sdc3_data"; + drive-strengh = <8>; + bias-pull-up; + }; + }; + ps_hold: ps_hold { mux { pins = "gpio78"; diff --git a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts index 93d08b9a77c9..ebd675ca94b4 100644 --- a/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts +++ b/arch/arm/boot/dts/qcom-apq8064-sony-xperia-yuga.dts @@ -71,26 +71,6 @@ }; - sdcc3_pin_a: sdcc3-pin-active { - clk { - pins = "sdc3_clk"; - drive-strengh = <8>; - bias-disable; - }; - - cmd { - pins = "sdc3_cmd"; - drive-strengh = <8>; - bias-pull-up; - }; - - data { - pins = "sdc3_data"; - drive-strengh = <8>; - bias-pull-up; - }; - }; - sdcc3_cd_pin_a: sdcc3-cd-pin-active { pins = "gpio26"; function = "gpio"; @@ -407,7 +387,7 @@ cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>; pinctrl-names = "default"; - pinctrl-0 = <&sdcc3_pin_a>, <&sdcc3_cd_pin_a>; + pinctrl-0 = <&sdcc3_pins>, <&sdcc3_cd_pin_a>; }; }; }; -- cgit v1.2.3 From 5f963e2951d019bc217fdc722dba765ac494eec2 Mon Sep 17 00:00:00 2001 From: Srinivas Kandagatla Date: Fri, 10 Jun 2016 19:19:54 +0100 Subject: ARM: dts: apq8064: rename db600c to SD_600eval This board has been renamed recently and announced at https://eragon.einfochips.com/products/sd-600eval.html So rename this board files so that it reflects actual product in market. Signed-off-by: Srinivas Kandagatla Signed-off-by: Andy Gross --- arch/arm/boot/dts/Makefile | 2 +- .../boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi | 52 --- arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts | 349 --------------------- .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 52 +++ .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 349 +++++++++++++++++++++ 5 files changed, 402 insertions(+), 402 deletions(-) delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi create mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts (limited to 'arch') diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 06b6c2d695bf..5b7c17a1950e 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -572,7 +572,7 @@ dtb-$(CONFIG_ARCH_PRIMA2) += \ dtb-$(CONFIG_ARCH_OXNAS) += \ wd-mbwe.dtb dtb-$(CONFIG_ARCH_QCOM) += \ - qcom-apq8064-arrow-db600c.dtb \ + qcom-apq8064-arrow-sd-600eval.dtb \ qcom-apq8064-cm-qs600.dtb \ qcom-apq8064-ifc6410.dtb \ qcom-apq8064-sony-xperia-yuga.dtb \ diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi deleted file mode 100644 index a3efb9704fcd..000000000000 --- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c-pins.dtsi +++ /dev/null @@ -1,52 +0,0 @@ -&tlmm_pinmux { - card_detect: card-detect { - mux { - pins = "gpio26"; - function = "gpio"; - bias-disable; - }; - }; - - pcie_pins: pcie-pinmux { - mux { - pins = "gpio27"; - function = "gpio"; - }; - conf { - pins = "gpio27"; - drive-strength = <12>; - bias-disable; - }; - }; - - user_leds: user-leds { - mux { - pins = "gpio3", "gpio7", "gpio10", "gpio11"; - function = "gpio"; - }; - - conf { - pins = "gpio3", "gpio7", "gpio10", "gpio11"; - function = "gpio"; - output-low; - }; - }; - - magneto_pins: magneto-pins { - mux { - pins = "gpio31", "gpio48"; - function = "gpio"; - bias-disable; - }; - }; -}; - -&pm8921_mpps { - mpp_leds: mpp-leds { - pinconf { - pins = "mpp7", "mpp8"; - function = "digital"; - output-low; - }; - }; -}; diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts deleted file mode 100644 index e01b27ea7fba..000000000000 --- a/arch/arm/boot/dts/qcom-apq8064-arrow-db600c.dts +++ /dev/null @@ -1,349 +0,0 @@ -#include "qcom-apq8064-v2.0.dtsi" -#include "qcom-apq8064-arrow-db600c-pins.dtsi" -#include - -/ { - model = "Arrow Electronics, APQ8064 DB600c"; - compatible = "arrow,db600c", "qcom,apq8064"; - - aliases { - serial0 = &gsbi7_serial; - serial1 = &gsbi1_serial; - i2c0 = &gsbi2_i2c; - i2c1 = &gsbi3_i2c; - i2c2 = &gsbi4_i2c; - i2c3 = &gsbi7_i2c; - spi0 = &gsbi5_spi; - }; - - regulators { - compatible = "simple-bus"; - vph: regulator-fixed@1 { - compatible = "regulator-fixed"; - regulator-min-microvolt = <4500000>; - regulator-max-microvolt = <4500000>; - regulator-name = "VPH"; - regulator-type = "voltage"; - regulator-boot-on; - }; - - /* on board fixed 3.3v supply */ - vcc3v3: vcc3v3 { - compatible = "regulator-fixed"; - regulator-name = "VCC3V3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - }; - - soc { - rpm@108000 { - regulators { - vdd_s1-supply = <&vph>; - vdd_s2-supply = <&vph>; - vdd_s3-supply = <&vph>; - vdd_s4-supply = <&vph>; - vdd_s5-supply = <&vph>; - vdd_s6-supply = <&vph>; - vdd_s7-supply = <&vph>; - vdd_l1_l2_l12_l18-supply = <&pm8921_s4>; - vdd_l3_l15_l17-supply = <&vph>; - vdd_l4_l14-supply = <&vph>; - vdd_l5_l8_l16-supply = <&vph>; - vdd_l6_l7-supply = <&vph>; - vdd_l9_l11-supply = <&vph>; - vdd_l10_l22-supply = <&vph>; - vdd_l21_l23_l29-supply = <&vph>; - vdd_l24-supply = <&pm8921_s1>; - vdd_l25-supply = <&pm8921_s1>; - vdd_l26-supply = <&pm8921_s7>; - vdd_l27-supply = <&pm8921_s7>; - vdd_l28-supply = <&pm8921_s7>; - vin_lvs1_3_6-supply = <&pm8921_s4>; - vin_lvs2-supply = <&pm8921_s1>; - vin_lvs4_5_7-supply = <&pm8921_s4>; - - s1 { - regulator-always-on; - regulator-min-microvolt = <1225000>; - regulator-max-microvolt = <1225000>; - qcom,switch-mode-frequency = <3200000>; - bias-pull-down; - }; - - s3 { - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1400000>; - qcom,switch-mode-frequency = <4800000>; - }; - - s4 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <1800000>; - qcom,switch-mode-frequency = <3200000>; - bias-pull-down; - regulator-always-on; - }; - - s7 { - regulator-min-microvolt = <1300000>; - regulator-max-microvolt = <1300000>; - qcom,switch-mode-frequency = <3200000>; - }; - - l3 { - regulator-min-microvolt = <3050000>; - regulator-max-microvolt = <3300000>; - bias-pull-down; - }; - - l4 { - regulator-min-microvolt = <1000000>; - regulator-max-microvolt = <1800000>; - bias-pull-down; - }; - - l5 { - regulator-min-microvolt = <2750000>; - regulator-max-microvolt = <3000000>; - bias-pull-down; - regulator-boot-on; - regulator-always-on; - }; - - l6 { - regulator-min-microvolt = <2950000>; - regulator-max-microvolt = <2950000>; - bias-pull-down; - }; - - l23 { - regulator-min-microvolt = <1700000>; - regulator-max-microvolt = <1900000>; - bias-pull-down; - }; - - lvs6 { - bias-pull-down; - }; - - lvs7 { - bias-pull-down; - }; - }; - }; - - gsbi@12440000 { - status = "okay"; - qcom,mode = ; - serial@12450000 { - label = "LS-UART1"; - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&gsbi1_uart_4pins>; - }; - }; - - gsbi@12480000 { - status = "okay"; - qcom,mode = ; - i2c@124a0000 { - /* On Low speed expansion and Sensors */ - label = "LS-I2C0"; - status = "okay"; - lis3mdl_mag@1e { - compatible = "st,lis3mdl-magn"; - reg = <0x1e>; - vdd-supply = <&vcc3v3>; - vddio-supply = <&pm8921_s4>; - pinctrl-names = "default"; - pinctrl-0 = <&magneto_pins>; - interrupt-parent = <&tlmm_pinmux>; - - st,drdy-int-pin = <2>; - interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */ - <31 IRQ_TYPE_EDGE_RISING>; /* INT */ - }; - }; - }; - - gsbi@16200000 { - status = "okay"; - qcom,mode = ; - i2c@16280000 { - /* On Low speed expansion */ - status = "okay"; - label = "LS-I2C1"; - clock-frequency = <200000>; - eeprom@52 { - compatible = "atmel,24c128"; - reg = <0x52>; - pagesize = <64>; - }; - }; - }; - - gsbi@16300000 { - status = "okay"; - qcom,mode = ; - i2c@16380000 { - /* On High speed expansion */ - label = "HS-CAM-I2C3"; - status = "okay"; - }; - }; - - gsbi@1a200000 { - status = "okay"; - spi@1a280000 { - /* On Low speed expansion */ - label = "LS-SPI0"; - status = "okay"; - }; - }; - - /* DEBUG UART */ - gsbi@16600000 { - status = "okay"; - qcom,mode = ; - serial@16640000 { - label = "LS-UART0"; - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&gsbi7_uart_2pins>; - }; - - i2c@16680000 { - /* On High speed expansion */ - status = "okay"; - label = "HS-CAM-I2C2"; - }; - }; - - leds { - pinctrl-names = "default"; - pinctrl-0 = <&user_leds>, <&mpp_leds>; - - compatible = "gpio-leds"; - - user-led0 { - label = "user0-led"; - gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "heartbeat"; - default-state = "off"; - }; - - user-led1 { - label = "user1-led"; - gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc0"; - default-state = "off"; - }; - - user-led2 { - label = "user2-led"; - gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "mmc1"; - default-state = "off"; - }; - - user-led3 { - label = "user3-led"; - gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "none"; - default-state = "off"; - }; - - wifi-led { - label = "WiFi-led"; - gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - - bt-led { - label = "BT-led"; - gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>; - default-state = "off"; - }; - }; - - pci@1b500000 { - status = "okay"; - vdda-supply = <&pm8921_s3>; - vdda_phy-supply = <&pm8921_lvs6>; - vdda_refclk-supply = <&vcc3v3>; - pinctrl-0 = <&pcie_pins>; - pinctrl-names = "default"; - perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>; - }; - - phy@1b400000 { - status = "okay"; - }; - - sata@29000000 { - status = "okay"; - target-supply = <&pm8921_lvs7>; - }; - - /* OTG */ - phy@12500000 { - status = "okay"; - dr_mode = "peripheral"; - vddcx-supply = <&pm8921_s3>; - v3p3-supply = <&pm8921_l3>; - v1p8-supply = <&pm8921_l4>; - }; - - phy@12520000 { - status = "okay"; - vddcx-supply = <&pm8921_s3>; - v3p3-supply = <&pm8921_l3>; - v1p8-supply = <&pm8921_l23>; - }; - - phy@12530000 { - status = "okay"; - vddcx-supply = <&pm8921_s3>; - v3p3-supply = <&pm8921_l3>; - v1p8-supply = <&pm8921_l23>; - }; - - gadget@12500000 { - status = "okay"; - }; - - /* OTG */ - usb@12500000 { - status = "okay"; - }; - - usb@12520000 { - status = "okay"; - }; - - usb@12530000 { - status = "okay"; - }; - - amba { - /* eMMC */ - sdcc@12400000 { - status = "okay"; - vmmc-supply = <&pm8921_l5>; - vqmmc-supply = <&pm8921_s4>; - }; - - /* External micro SD card */ - sdcc@12180000 { - status = "okay"; - vmmc-supply = <&pm8921_l6>; - pinctrl-names = "default"; - pinctrl-0 = <&card_detect>; - cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>; - }; - }; - }; -}; diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi new file mode 100644 index 000000000000..a3efb9704fcd --- /dev/null +++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi @@ -0,0 +1,52 @@ +&tlmm_pinmux { + card_detect: card-detect { + mux { + pins = "gpio26"; + function = "gpio"; + bias-disable; + }; + }; + + pcie_pins: pcie-pinmux { + mux { + pins = "gpio27"; + function = "gpio"; + }; + conf { + pins = "gpio27"; + drive-strength = <12>; + bias-disable; + }; + }; + + user_leds: user-leds { + mux { + pins = "gpio3", "gpio7", "gpio10", "gpio11"; + function = "gpio"; + }; + + conf { + pins = "gpio3", "gpio7", "gpio10", "gpio11"; + function = "gpio"; + output-low; + }; + }; + + magneto_pins: magneto-pins { + mux { + pins = "gpio31", "gpio48"; + function = "gpio"; + bias-disable; + }; + }; +}; + +&pm8921_mpps { + mpp_leds: mpp-leds { + pinconf { + pins = "mpp7", "mpp8"; + function = "digital"; + output-low; + }; + }; +}; diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts new file mode 100644 index 000000000000..7df0108cec39 --- /dev/null +++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts @@ -0,0 +1,349 @@ +#include "qcom-apq8064-v2.0.dtsi" +#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi" +#include + +/ { + model = "Arrow Electronics, APQ8064 SD_600eval"; + compatible = "arrow,sd_600eval", "qcom,apq8064"; + + aliases { + serial0 = &gsbi7_serial; + serial1 = &gsbi1_serial; + i2c0 = &gsbi2_i2c; + i2c1 = &gsbi3_i2c; + i2c2 = &gsbi4_i2c; + i2c3 = &gsbi7_i2c; + spi0 = &gsbi5_spi; + }; + + regulators { + compatible = "simple-bus"; + vph: regulator-fixed@1 { + compatible = "regulator-fixed"; + regulator-min-microvolt = <4500000>; + regulator-max-microvolt = <4500000>; + regulator-name = "VPH"; + regulator-type = "voltage"; + regulator-boot-on; + }; + + /* on board fixed 3.3v supply */ + vcc3v3: vcc3v3 { + compatible = "regulator-fixed"; + regulator-name = "VCC3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + }; + + soc { + rpm@108000 { + regulators { + vdd_s1-supply = <&vph>; + vdd_s2-supply = <&vph>; + vdd_s3-supply = <&vph>; + vdd_s4-supply = <&vph>; + vdd_s5-supply = <&vph>; + vdd_s6-supply = <&vph>; + vdd_s7-supply = <&vph>; + vdd_l1_l2_l12_l18-supply = <&pm8921_s4>; + vdd_l3_l15_l17-supply = <&vph>; + vdd_l4_l14-supply = <&vph>; + vdd_l5_l8_l16-supply = <&vph>; + vdd_l6_l7-supply = <&vph>; + vdd_l9_l11-supply = <&vph>; + vdd_l10_l22-supply = <&vph>; + vdd_l21_l23_l29-supply = <&vph>; + vdd_l24-supply = <&pm8921_s1>; + vdd_l25-supply = <&pm8921_s1>; + vdd_l26-supply = <&pm8921_s7>; + vdd_l27-supply = <&pm8921_s7>; + vdd_l28-supply = <&pm8921_s7>; + vin_lvs1_3_6-supply = <&pm8921_s4>; + vin_lvs2-supply = <&pm8921_s1>; + vin_lvs4_5_7-supply = <&pm8921_s4>; + + s1 { + regulator-always-on; + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + qcom,switch-mode-frequency = <3200000>; + bias-pull-down; + }; + + s3 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + qcom,switch-mode-frequency = <4800000>; + }; + + s4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + qcom,switch-mode-frequency = <3200000>; + bias-pull-down; + regulator-always-on; + }; + + s7 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + qcom,switch-mode-frequency = <3200000>; + }; + + l3 { + regulator-min-microvolt = <3050000>; + regulator-max-microvolt = <3300000>; + bias-pull-down; + }; + + l4 { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + + l5 { + regulator-min-microvolt = <2750000>; + regulator-max-microvolt = <3000000>; + bias-pull-down; + regulator-boot-on; + regulator-always-on; + }; + + l6 { + regulator-min-microvolt = <2950000>; + regulator-max-microvolt = <2950000>; + bias-pull-down; + }; + + l23 { + regulator-min-microvolt = <1700000>; + regulator-max-microvolt = <1900000>; + bias-pull-down; + }; + + lvs6 { + bias-pull-down; + }; + + lvs7 { + bias-pull-down; + }; + }; + }; + + gsbi@12440000 { + status = "okay"; + qcom,mode = ; + serial@12450000 { + label = "LS-UART1"; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&gsbi1_uart_4pins>; + }; + }; + + gsbi@12480000 { + status = "okay"; + qcom,mode = ; + i2c@124a0000 { + /* On Low speed expansion and Sensors */ + label = "LS-I2C0"; + status = "okay"; + lis3mdl_mag@1e { + compatible = "st,lis3mdl-magn"; + reg = <0x1e>; + vdd-supply = <&vcc3v3>; + vddio-supply = <&pm8921_s4>; + pinctrl-names = "default"; + pinctrl-0 = <&magneto_pins>; + interrupt-parent = <&tlmm_pinmux>; + + st,drdy-int-pin = <2>; + interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */ + <31 IRQ_TYPE_EDGE_RISING>; /* INT */ + }; + }; + }; + + gsbi@16200000 { + status = "okay"; + qcom,mode = ; + i2c@16280000 { + /* On Low speed expansion */ + status = "okay"; + label = "LS-I2C1"; + clock-frequency = <200000>; + eeprom@52 { + compatible = "atmel,24c128"; + reg = <0x52>; + pagesize = <64>; + }; + }; + }; + + gsbi@16300000 { + status = "okay"; + qcom,mode = ; + i2c@16380000 { + /* On High speed expansion */ + label = "HS-CAM-I2C3"; + status = "okay"; + }; + }; + + gsbi@1a200000 { + status = "okay"; + spi@1a280000 { + /* On Low speed expansion */ + label = "LS-SPI0"; + status = "okay"; + }; + }; + + /* DEBUG UART */ + gsbi@16600000 { + status = "okay"; + qcom,mode = ; + serial@16640000 { + label = "LS-UART0"; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&gsbi7_uart_2pins>; + }; + + i2c@16680000 { + /* On High speed expansion */ + status = "okay"; + label = "HS-CAM-I2C2"; + }; + }; + + leds { + pinctrl-names = "default"; + pinctrl-0 = <&user_leds>, <&mpp_leds>; + + compatible = "gpio-leds"; + + user-led0 { + label = "user0-led"; + gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + default-state = "off"; + }; + + user-led1 { + label = "user1-led"; + gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + default-state = "off"; + }; + + user-led2 { + label = "user2-led"; + gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc1"; + default-state = "off"; + }; + + user-led3 { + label = "user3-led"; + gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "none"; + default-state = "off"; + }; + + wifi-led { + label = "WiFi-led"; + gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + bt-led { + label = "BT-led"; + gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + }; + + pci@1b500000 { + status = "okay"; + vdda-supply = <&pm8921_s3>; + vdda_phy-supply = <&pm8921_lvs6>; + vdda_refclk-supply = <&vcc3v3>; + pinctrl-0 = <&pcie_pins>; + pinctrl-names = "default"; + perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>; + }; + + phy@1b400000 { + status = "okay"; + }; + + sata@29000000 { + status = "okay"; + target-supply = <&pm8921_lvs7>; + }; + + /* OTG */ + phy@12500000 { + status = "okay"; + dr_mode = "peripheral"; + vddcx-supply = <&pm8921_s3>; + v3p3-supply = <&pm8921_l3>; + v1p8-supply = <&pm8921_l4>; + }; + + phy@12520000 { + status = "okay"; + vddcx-supply = <&pm8921_s3>; + v3p3-supply = <&pm8921_l3>; + v1p8-supply = <&pm8921_l23>; + }; + + phy@12530000 { + status = "okay"; + vddcx-supply = <&pm8921_s3>; + v3p3-supply = <&pm8921_l3>; + v1p8-supply = <&pm8921_l23>; + }; + + gadget@12500000 { + status = "okay"; + }; + + /* OTG */ + usb@12500000 { + status = "okay"; + }; + + usb@12520000 { + status = "okay"; + }; + + usb@12530000 { + status = "okay"; + }; + + amba { + /* eMMC */ + sdcc@12400000 { + status = "okay"; + vmmc-supply = <&pm8921_l5>; + vqmmc-supply = <&pm8921_s4>; + }; + + /* External micro SD card */ + sdcc@12180000 { + status = "okay"; + vmmc-supply = <&pm8921_l6>; + pinctrl-names = "default"; + pinctrl-0 = <&card_detect>; + cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>; + }; + }; + }; +}; -- cgit v1.2.3 From 93b8e6fda11757a20df21f3fc18e12789841f173 Mon Sep 17 00:00:00 2001 From: Parth Pancholi Date: Fri, 10 Jun 2016 19:19:55 +0100 Subject: ARM: dts: sd_600eval: Fix eMMC lockup issue This board locks up if we stress test the eMMC, as the regulator s4 is unable to supply enough current for all the peripherials attached to it. As this supply is wired up to most of the peripherials including DDR, it resulted in such lockup. This patch fixes this issue by setting s4 regulator correctly with Auto power mode. Reported-by: Srinivas Kandagatla [Srinivas Kandagatla: rewrote the change log] Tested-by: Girish Sharma Signed-off-by: Parth Pancholi Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 4 +++- 1 file changed, 3 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts index 7df0108cec39..39ae2bc8cb08 100644 --- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts +++ b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts @@ -1,6 +1,7 @@ #include "qcom-apq8064-v2.0.dtsi" #include "qcom-apq8064-arrow-sd-600eval-pins.dtsi" #include +#include / { model = "Arrow Electronics, APQ8064 SD_600eval"; @@ -82,7 +83,8 @@ s4 { regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; - qcom,switch-mode-frequency = <3200000>; + qcom,switch-mode-frequency = <1600000>; + qcom,force-mode = ; bias-pull-down; regulator-always-on; }; -- cgit v1.2.3 From d32bfe101f73f5764a871c551460e12480477e63 Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Fri, 10 Jun 2016 17:15:28 -0500 Subject: ARM: dts: qcom: msm8974-honami: Set DMA as remotely controlled This patch adds the qcom,controlled-remotely property for the blsp2_bam controller node. This board requires this, otherwise the board fails to boot due to access of protected registers during BAM initialization. Fixes: 62bc81792223 dts: msm8974: Add blsp2_bam dma node Signed-off-by: Andy Gross Acked-by: Bjorn Andersson --- arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts | 4 ++++ 1 file changed, 4 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts index a0398b69f4f2..3fb4dada6b0d 100644 --- a/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts +++ b/arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts @@ -367,6 +367,10 @@ }; }; + + dma-controller@f9944000 { + qcom,controlled-remotely; + }; }; &spmi_bus { -- cgit v1.2.3 From 30f1e2dde68d22022a77a9c1c4ddfdcf2fc3b4f3 Mon Sep 17 00:00:00 2001 From: Andy Gross Date: Sun, 12 Jun 2016 01:20:11 -0500 Subject: arm: dts: qcom: Update smem state cells usage This patch updates the qcom,state-cells to qcom,smem-state-cells to match recent changes to the binding. Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064.dtsi | 2 +- arch/arm/boot/dts/qcom-msm8974.dtsi | 6 +++--- 2 files changed, 4 insertions(+), 4 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi index ce7ce846615e..906bb81cfd67 100644 --- a/arch/arm/boot/dts/qcom-apq8064.dtsi +++ b/arch/arm/boot/dts/qcom-apq8064.dtsi @@ -177,7 +177,7 @@ apps_smsm: apps@0 { reg = <0>; - #qcom,state-cells = <1>; + #qcom,smem-state-cells = <1>; }; modem_smsm: modem@1 { diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index 55328d6879fb..561d4d136762 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -182,7 +182,7 @@ modem_smp2p_out: master-kernel { qcom,entry-name = "master-kernel"; - #qcom,state-cells = <1>; + #qcom,smem-state-cells = <1>; }; modem_smp2p_in: slave-kernel { @@ -208,7 +208,7 @@ wcnss_smp2p_out: master-kernel { qcom,entry-name = "master-kernel"; - #qcom,state-cells = <1>; + #qcom,smem-state-cells = <1>; }; wcnss_smp2p_in: slave-kernel { @@ -232,7 +232,7 @@ apps_smsm: apps@0 { reg = <0>; - #qcom,state-cells = <1>; + #qcom,smem-state-cells = <1>; }; modem_smsm: modem@1 { -- cgit v1.2.3 From 72f3cd64dccf663b0a1705bf215987cd5a2a11d2 Mon Sep 17 00:00:00 2001 From: John Stultz Date: Tue, 26 Apr 2016 10:44:13 -0700 Subject: device-tree: nexus7: Remove power gpio key entry and use pmic8xxx-pwrkey Since the pmic8xxx-pwrkey driver is already supported in the qcom-apq8064.dtsi, and the pmic8xxx-pwrkey supports logic to configure proper device shutdown when ps_hold goes low, it is better to use that driver then a generic gpio button. Thus this patch remove the gpio power key entry here, so we don't get double input events from having two drivers enabled. Cc: Rob Herring Cc: Andy Gross Cc: Bjorn Andersson Cc: Stephen Boyd Cc: linux-arm-msm@vger.kernel.org Cc: devicetree@vger.kernel.org Acked-by: Rob Herring Acked-by: Bjorn Andersson Signed-off-by: John Stultz Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts | 6 ------ 1 file changed, 6 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts index 32fedfa149d0..7b05f072bfc2 100644 --- a/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts +++ b/arch/arm/boot/dts/qcom-apq8064-asus-nexus7-flo.dts @@ -29,12 +29,6 @@ gpio-keys { compatible = "gpio-keys"; - power { - label = "Power"; - gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_LOW>; - linux,code = ; - gpio-key,wakeup; - }; volume_up { label = "Volume Up"; gpios = <&pm8921_gpio 4 GPIO_ACTIVE_HIGH>; -- cgit v1.2.3 From 0840ea9e4457abedf92d3a89ab372fbb091e7a3c Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 17 Jun 2016 22:28:05 +0200 Subject: ARM: dts: add GPIO and MPP to MSM8660 PMIC This adds the 8660 PMIC GPIO and MPP blocks to the MSM8660 DTSI. Verified against the vendor tree to be in these locations with these interrupts, tested on the APQ8060 Dragonboard. Reviewed-by: Stephen Boyd Signed-off-by: Linus Walleij Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-msm8660.dtsi | 38 +++++++++++++++++++++++++++++++++++++ 1 file changed, 38 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index cd214030b84a..6a62b62ad980 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -143,6 +143,44 @@ #address-cells = <1>; #size-cells = <0>; + pm8058_gpio: gpio@150 { + compatible = "qcom,pm8058-gpio", + "qcom,ssbi-gpio"; + reg = <0x150>; + interrupt-parent = <&pmicintc>; + interrupts = <192 1>, <193 1>, <194 1>, + <195 1>, <196 1>, <197 1>, + <198 1>, <199 1>, <200 1>, + <201 1>, <202 1>, <203 1>, + <204 1>, <205 1>, <206 1>, + <207 1>, <208 1>, <209 1>, + <210 1>, <211 1>, <212 1>, + <213 1>, <214 1>, <215 1>, + <216 1>, <217 1>, <218 1>, + <219 1>, <220 1>, <221 1>, + <222 1>, <223 1>, <224 1>, + <225 1>, <226 1>, <227 1>, + <228 1>, <229 1>, <230 1>, + <231 1>, <232 1>, <233 1>, + <234 1>, <235 1>; + gpio-controller; + #gpio-cells = <2>; + + }; + + pm8058_mpps: mpps@50 { + compatible = "qcom,pm8058-mpp", + "qcom,ssbi-mpp"; + reg = <0x50>; + gpio-controller; + #gpio-cells = <2>; + interrupt-parent = <&pmicintc>; + interrupts = + <128 1>, <129 1>, <130 1>, <131 1>, + <132 1>, <133 1>, <134 1>, <135 1>, + <136 1>, <137 1>, <138 1>, <139 1>; + }; + pwrkey@1c { compatible = "qcom,pm8058-pwrkey"; reg = <0x1c>; -- cgit v1.2.3 From 5f7610076e5bbfde4b837c018a674170bcb26a92 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 17 Jun 2016 22:28:06 +0200 Subject: ARM: dts: add SDCC5 to Qualcomm MSM8660 The SDCC5 SD/MMC controller is used for a second uSD slot on the APQ8060 Dragonboard. On most other systems it is just dark silicon so define it and leave it as "disabled" in the core SoC file. Reviewed-by: Stephen Boyd Signed-off-by: Linus Walleij Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-msm8660.dtsi | 16 ++++++++++++++++ 1 file changed, 16 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index 6a62b62ad980..a5a38820554a 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -262,6 +262,22 @@ no-1-8-v; vmmc-supply = <&vsdcc_fixed>; }; + + sdcc5: sdcc@12200000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x00051180>; + status = "disabled"; + reg = <0x12200000 0x8000>; + interrupts = ; + interrupt-names = "cmd_irq"; + clocks = <&gcc SDC5_CLK>, <&gcc SDC5_H_CLK>; + clock-names = "mclk", "apb_pclk"; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <48000000>; + vmmc-supply = <&vsdcc_fixed>; + }; }; tcsr: syscon@1a400000 { -- cgit v1.2.3 From 30b4fb1cc40a0ee35f84e2431cadfe9ced40076a Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 17 Jun 2016 22:28:07 +0200 Subject: ARM: dts: add L2CC and RPM with regulators for MSM8660 This adds the L2CC IPC resource and RPM devices plus the nodes for the PM8901 and PM8058 regulators to the MSM8660 device tree. This was tested on the APQ8060 Dragonboard. Signed-off-by: Linus Walleij Reviewed-by: Stephen Boyd Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-msm8660.dtsi | 89 +++++++++++++++++++++++++++++++++++++ 1 file changed, 89 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index a5a38820554a..e7c6e2942f47 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -215,6 +215,95 @@ }; }; + l2cc: clock-controller@2082000 { + compatible = "syscon"; + reg = <0x02082000 0x1000>; + }; + + rpm: rpm@104000 { + compatible = "qcom,rpm-msm8660"; + reg = <0x00104000 0x1000>; + qcom,ipc = <&l2cc 0x8 2>; + + interrupts = , + , + ; + interrupt-names = "ack", "err", "wakeup"; + clocks = <&gcc RPM_MSG_RAM_H_CLK>; + clock-names = "ram"; + + rpmcc: clock-controller { + compatible = "qcom,rpmcc-apq8660", "qcom,rpmcc"; + #clock-cells = <1>; + }; + + pm8901-regulators { + compatible = "qcom,rpm-pm8901-regulators"; + + pm8901_l0: l0 {}; + pm8901_l1: l1 {}; + pm8901_l2: l2 {}; + pm8901_l3: l3 {}; + pm8901_l4: l4 {}; + pm8901_l5: l5 {}; + pm8901_l6: l6 {}; + + /* S0 and S1 Handled as SAW regulators by SPM */ + pm8901_s2: s2 {}; + pm8901_s3: s3 {}; + pm8901_s4: s4 {}; + + pm8901_lvs0: lvs0 {}; + pm8901_lvs1: lvs1 {}; + pm8901_lvs2: lvs2 {}; + pm8901_lvs3: lvs3 {}; + + pm8901_mvs: mvs {}; + }; + + pm8058-regulators { + compatible = "qcom,rpm-pm8058-regulators"; + + pm8058_l0: l0 {}; + pm8058_l1: l1 {}; + pm8058_l2: l2 {}; + pm8058_l3: l3 {}; + pm8058_l4: l4 {}; + pm8058_l5: l5 {}; + pm8058_l6: l6 {}; + pm8058_l7: l7 {}; + pm8058_l8: l8 {}; + pm8058_l9: l9 {}; + pm8058_l10: l10 {}; + pm8058_l11: l11 {}; + pm8058_l12: l12 {}; + pm8058_l13: l13 {}; + pm8058_l14: l14 {}; + pm8058_l15: l15 {}; + pm8058_l16: l16 {}; + pm8058_l17: l17 {}; + pm8058_l18: l18 {}; + pm8058_l19: l19 {}; + pm8058_l20: l20 {}; + pm8058_l21: l21 {}; + pm8058_l22: l22 {}; + pm8058_l23: l23 {}; + pm8058_l24: l24 {}; + pm8058_l25: l25 {}; + + pm8058_s0: s0 {}; + pm8058_s1: s1 {}; + pm8058_s2: s2 {}; + pm8058_s3: s3 {}; + pm8058_s4: s4 {}; + + pm8058_lvs0: lvs0 {}; + pm8058_lvs1: lvs1 {}; + + pm8058_ncp: ncp {}; + }; + }; + /* Temporary fixed regulator */ vsdcc_fixed: vsdcc-regulator { compatible = "regulator-fixed"; -- cgit v1.2.3 From c51cb1a15676daed1d1a7fc8a0f2d1e3ae125361 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 17 Jun 2016 22:28:09 +0200 Subject: ARM: dts: add I2C block in GSBI12 The I2C block on the GSBI12 is used on the APQ8060 Dragonboard for sensors. Make it available in the chipset file. Take this opportunity to fix the IRQ flag "0" to "NONE" using the IRQ DT include. Signed-off-by: Linus Walleij Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-msm8660.dtsi | 13 ++++++++++++- 1 file changed, 12 insertions(+), 1 deletion(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index e7c6e2942f47..8ee3045f4066 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -122,11 +122,22 @@ compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x19c40000 0x1000>, <0x19c00000 0x1000>; - interrupts = <0 195 0x0>; + interrupts = <0 195 IRQ_TYPE_NONE>; clocks = <&gcc GSBI12_UART_CLK>, <&gcc GSBI12_H_CLK>; clock-names = "core", "iface"; status = "disabled"; }; + + gsbi12_i2c: i2c@19c80000 { + compatible = "qcom,i2c-qup-v1.1.1"; + reg = <0x19c80000 0x1000>; + interrupts = <0 196 IRQ_TYPE_NONE>; + clocks = <&gcc GSBI12_QUP_CLK>, <&gcc GSBI12_H_CLK>; + clock-names = "core", "iface"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; qcom,ssbi@500000 { -- cgit v1.2.3 From e20fd3364c0222a582cb45e061c677e232116236 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 17 Jun 2016 22:28:10 +0200 Subject: ARM: dts: fix the MSM8660 RTC base address The RTC was defined on 0x11d but on the MSM8660/APQ8060 it is actually on 0x1e8. We were saved by the fact that the driver does not use the reg parameter: instead it uses the compatible string to figure out where the RTC is. Signed-off-by: Linus Walleij Reviewed-by: Stephen Boyd Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-msm8660.dtsi | 4 ++-- 1 file changed, 2 insertions(+), 2 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index 8ee3045f4066..b7d7f0c27ba1 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -211,11 +211,11 @@ row-hold = <91500>; }; - rtc@11d { + rtc@1e8 { compatible = "qcom,pm8058-rtc"; + reg = <0x1e8>; interrupt-parent = <&pmicintc>; interrupts = <39 1>; - reg = <0x11d>; allow-set-time; }; -- cgit v1.2.3 From 1758b35808ce451b6c1bca05d60031fbcf3cb5ca Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 17 Jun 2016 22:28:11 +0200 Subject: ARM: dts: move the fixed MMC regulator to SURF board There is currently a fixed regulator in the .dtsi file for the MSM8660 chipset, used by the SURF board. We want to define real regulators for a board using this chipset, so push the fixed regulator down to the SURF board which is the only user. Reviewed-by: Stephen Boyd Signed-off-by: Linus Walleij Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-msm8660-surf.dts | 11 +++++++++++ arch/arm/boot/dts/qcom-msm8660.dtsi | 12 ------------ 2 files changed, 11 insertions(+), 12 deletions(-) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts index b17f379e8c2a..23de764558ab 100644 --- a/arch/arm/boot/dts/qcom-msm8660-surf.dts +++ b/arch/arm/boot/dts/qcom-msm8660-surf.dts @@ -23,15 +23,26 @@ }; }; + /* Temporary fixed regulator */ + vsdcc_fixed: vsdcc-regulator { + compatible = "regulator-fixed"; + regulator-name = "SDCC Power"; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2700000>; + regulator-always-on; + }; + amba { /* eMMC */ sdcc1: sdcc@12400000 { status = "okay"; + vmmc-supply = <&vsdcc_fixed>; }; /* External micro SD card */ sdcc3: sdcc@12180000 { status = "okay"; + vmmc-supply = <&vsdcc_fixed>; }; }; }; diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index b7d7f0c27ba1..acbe71febe13 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -315,15 +315,6 @@ }; }; - /* Temporary fixed regulator */ - vsdcc_fixed: vsdcc-regulator { - compatible = "regulator-fixed"; - regulator-name = "SDCC Power"; - regulator-min-microvolt = <2700000>; - regulator-max-microvolt = <2700000>; - regulator-always-on; - }; - amba { compatible = "simple-bus"; #address-cells = <1>; @@ -343,7 +334,6 @@ non-removable; cap-sd-highspeed; cap-mmc-highspeed; - vmmc-supply = <&vsdcc_fixed>; }; sdcc3: sdcc@12180000 { @@ -360,7 +350,6 @@ cap-mmc-highspeed; max-frequency = <48000000>; no-1-8-v; - vmmc-supply = <&vsdcc_fixed>; }; sdcc5: sdcc@12200000 { @@ -376,7 +365,6 @@ cap-sd-highspeed; cap-mmc-highspeed; max-frequency = <48000000>; - vmmc-supply = <&vsdcc_fixed>; }; }; -- cgit v1.2.3 From 4892e0756c65d6e248e7e8ff94845e8e26bcf896 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Fri, 17 Jun 2016 22:28:12 +0200 Subject: ARM: dts: add Qualcomm APQ8060-based Dragonboard This is the first Dragonboard based on APQ8060 and PM8058. It was produced in 2011 in cooperation between Qualcomm and BSQUARE. Signed-off-by: Linus Walleij Signed-off-by: Andy Gross --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 626 +++++++++++++++++++++++++ 2 files changed, 627 insertions(+) create mode 100644 arch/arm/boot/dts/qcom-apq8060-dragonboard.dts (limited to 'arch') diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 5b7c17a1950e..b359dce6ef7c 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -572,6 +572,7 @@ dtb-$(CONFIG_ARCH_PRIMA2) += \ dtb-$(CONFIG_ARCH_OXNAS) += \ wd-mbwe.dtb dtb-$(CONFIG_ARCH_QCOM) += \ + qcom-apq8060-dragonboard.dtb \ qcom-apq8064-arrow-sd-600eval.dtb \ qcom-apq8064-cm-qs600.dtb \ qcom-apq8064-ifc6410.dtb \ diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts new file mode 100644 index 000000000000..0abc93e5bb00 --- /dev/null +++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts @@ -0,0 +1,626 @@ +/* + * Copyright 2016 Linaro Ltd + * + * Permission is hereby granted, free of charge, to any person obtaining a copy + * of this software and associated documentation files (the "Software"), to deal + * in the Software without restriction, including without limitation the rights + * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell + * copies of the Software, and to permit persons to whom the Software is + * furnished to do so, subject to the following conditions: + * + * The above copyright notice and this permission notice shall be included in + * all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR + * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, + * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL + * THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER + * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, + * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN + * THE SOFTWARE. + */ + +#include +#include +#include +#include "qcom-msm8660.dtsi" + +/ { + model = "Qualcomm APQ8060 Dragonboard"; + compatible = "qcom,apq8060-dragonboard", "qcom,msm8660"; + + aliases { + serial0 = &gsbi12_serial; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + regulators { + compatible = "simple-bus"; + + /* Main power of the board: 3.7V */ + vph: regulator-fixed { + compatible = "regulator-fixed"; + regulator-min-microvolt = <3700000>; + regulator-max-microvolt = <3700000>; + regulator-name = "VPH"; + regulator-type = "voltage"; + regulator-always-on; + regulator-boot-on; + }; + + /* This is a levelshifter for SDCC5 */ + dragon_vio_txb: txb0104rgyr { + compatible = "regulator-fixed"; + regulator-name = "Dragon SDCC levelshifter"; + vin-supply = <&pm8058_l14>; + regulator-always-on; + }; + }; + + soc { + pinctrl@800000 { + /* eMMMC pins, all 8 data lines connected */ + dragon_sdcc1_pins: sdcc1 { + mux { + pins = "gpio159", "gpio160", "gpio161", + "gpio162", "gpio163", "gpio164", + "gpio165", "gpio166", "gpio167", + "gpio168"; + function = "sdc1"; + }; + clk { + pins = "gpio167"; /* SDC5 CLK */ + drive-strength = <16>; + bias-disable; + }; + cmd { + pins = "gpio168"; /* SDC5 CMD */ + drive-strength = <10>; + bias-pull-up; + }; + data { + /* SDC5 D0 to D7 */ + pins = "gpio159", "gpio160", "gpio161", "gpio162", + "gpio163", "gpio164", "gpio165", "gpio166"; + drive-strength = <10>; + bias-pull-up; + }; + }; + + /* + * The SDCC3 pins are hardcoded (non-muxable) but need some pin + * configuration. + */ + dragon_sdcc3_pins: sdcc3 { + clk { + pins = "sdc3_clk"; + drive-strength = <8>; + bias-disable; + }; + cmd { + pins = "sdc3_cmd"; + drive-strength = <8>; + bias-pull-up; + }; + data { + pins = "sdc3_data"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + /* Second SD card slot pins */ + dragon_sdcc5_pins: sdcc5 { + mux { + pins = "gpio95", "gpio96", "gpio97", + "gpio98", "gpio99", "gpio100"; + function = "sdc5"; + }; + clk { + pins = "gpio97"; /* SDC5 CLK */ + drive-strength = <16>; + bias-disable; + }; + cmd { + pins = "gpio95"; /* SDC5 CMD */ + drive-strength = <10>; + bias-pull-up; + }; + data { + /* SDC5 D0 to D3 */ + pins = "gpio96", "gpio98", "gpio99", "gpio100"; + drive-strength = <10>; + bias-pull-up; + }; + }; + + dragon_gsbi12_i2c_pins: gsbi12_i2c { + mux { + pins = "gpio115", "gpio116"; + function = "gsbi12"; + }; + pinconf { + pins = "gpio115", "gpio116"; + drive-strength = <16>; + /* These have external pull-up 4.7kOhm to 1.8V */ + bias-disable; + }; + }; + + /* Primary serial port uart 0 pins */ + dragon_gsbi12_serial_pins: gsbi12_serial { + mux { + pins = "gpio117", "gpio118"; + function = "gsbi12"; + }; + tx { + pins = "gpio117"; + drive-strength = <8>; + bias-disable; + }; + rx { + pins = "gpio118"; + drive-strength = <2>; + bias-pull-up; + }; + }; + }; + + qcom,ssbi@500000 { + pmic@0 { + keypad@148 { + linux,keymap = < + MATRIX_KEY(0, 0, KEY_MENU) + MATRIX_KEY(0, 2, KEY_1) + MATRIX_KEY(0, 3, KEY_4) + MATRIX_KEY(0, 4, KEY_7) + MATRIX_KEY(1, 0, KEY_UP) + MATRIX_KEY(1, 1, KEY_LEFT) + MATRIX_KEY(1, 2, KEY_DOWN) + MATRIX_KEY(1, 3, KEY_5) + MATRIX_KEY(1, 3, KEY_8) + MATRIX_KEY(2, 0, KEY_HOME) + MATRIX_KEY(2, 1, KEY_REPLY) + MATRIX_KEY(2, 2, KEY_2) + MATRIX_KEY(2, 3, KEY_6) + MATRIX_KEY(3, 0, KEY_VOLUMEUP) + MATRIX_KEY(3, 1, KEY_RIGHT) + MATRIX_KEY(3, 2, KEY_3) + MATRIX_KEY(3, 3, KEY_9) + MATRIX_KEY(3, 4, KEY_SWITCHVIDEOMODE) + MATRIX_KEY(4, 0, KEY_VOLUMEDOWN) + MATRIX_KEY(4, 1, KEY_BACK) + MATRIX_KEY(4, 2, KEY_CAMERA) + MATRIX_KEY(4, 3, KEY_KBDILLUMTOGGLE) + >; + keypad,num-rows = <6>; + keypad,num-columns = <5>; + }; + + gpio@150 { + dragon_bmp085_gpios: bmp085-gpios { + pinconf { + pins = "gpio16"; + function = "normal"; + input-enable; + bias-disable; + power-source = ; + }; + }; + dragon_sdcc3_gpios: sdcc3-gpios { + pinconf { + pins = "gpio22"; + function = "normal"; + input-enable; + bias-disable; + power-source = ; + }; + }; + dragon_sdcc5_gpios: sdcc5-gpios { + pinconf { + pins = "gpio26"; + function = "normal"; + input-enable; + bias-pull-up; + qcom,pull-up-strength = ; + power-source = ; + }; + }; + dragon_ak8975_gpios: ak8975-gpios { + pinconf { + pins = "gpio33"; + function = "normal"; + input-enable; + bias-disable; + power-source = ; + }; + }; + }; + }; + }; + + gsbi@19c00000 { + status = "ok"; + qcom,mode = ; + + serial@19c40000 { + status = "ok"; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_gsbi12_serial_pins>; + }; + + i2c@19c80000 { + status = "ok"; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_gsbi12_i2c_pins>; + + ak8975@0c { + compatible = "asahi-kasei,ak8975"; + reg = <0x0c>; + /* GPIO33 has interrupt 224 on the PM8058 */ + interrupt-parent = <&pm8058_gpio>; + interrupts = <224 IRQ_TYPE_EDGE_RISING>; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_ak8975_gpios>; + vid-supply = <&pm8058_lvs0>; // 1.8V + vdd-supply = <&pm8058_l14>; // 2.85V + }; + bmp085@77 { + compatible = "bosch,bmp085"; + reg = <0x77>; + /* GPIO16 has interrupt 207 on the PM8058 */ + interrupt-parent = <&pm8058_gpio>; + interrupts = <207 IRQ_TYPE_EDGE_RISING>; + reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_bmp085_gpios>; + vddd-supply = <&pm8058_lvs0>; // 1.8V + vdda-supply = <&pm8058_l14>; // 2.85V + }; + }; + }; + + rpm@104000 { + /* + * Set up of the PMIC RPM regulators for this board + * PM8901 supplies "preliminary regulators" whatever + * that means + */ + pm8901-regulators { + vdd_l0-supply = <&pm8901_s4>; + vdd_l1-supply = <&vph>; + vdd_l2-supply = <&vph>; + vdd_l3-supply = <&vph>; + vdd_l4-supply = <&vph>; + vdd_l5-supply = <&vph>; + vdd_l6-supply = <&vph>; + /* vdd_s0-supply, vdd_s1-supply: SAW regulators */ + vdd_s2-supply = <&vph>; + vdd_s3-supply = <&vph>; + vdd_s4-supply = <&vph>; + lvs0_in-supply = <&pm8058_s3>; + lvs1_in-supply = <&pm8901_s4>; + lvs2_in-supply = <&pm8058_l0>; + lvs3_in-supply = <&pm8058_s2>; + mvs_in-supply = <&pm8058_s3>; + + l0 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + l1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + bias-pull-down; + }; + l2 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <3300000>; + bias-pull-down; + }; + l3 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + bias-pull-down; + }; + l4 { + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <2600000>; + bias-pull-down; + }; + l5 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + l6 { + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + bias-pull-down; + }; + + /* s0 and s1 are SAW regulators controlled over SPM */ + s2 { + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + s3 { + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + s4 { + regulator-min-microvolt = <1225000>; + regulator-max-microvolt = <1225000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + + /* LVS0 thru 3 and mvs0 are just switches */ + lvs0 { + regulator-always-on; + }; + lvs1 { }; + lvs2 { }; + lvs3 { }; + mvs0 {}; + + }; + + pm8058-regulators { + vdd_l0_l1_lvs-supply = <&pm8058_s3>; + vdd_l2_l11_l12-supply = <&vph>; + vdd_l3_l4_l5-supply = <&vph>; + vdd_l6_l7-supply = <&vph>; + vdd_l8-supply = <&vph>; + vdd_l9-supply = <&vph>; + vdd_l10-supply = <&vph>; + vdd_l13_l16-supply = <&pm8058_s4>; + vdd_l14_l15-supply = <&vph>; + vdd_l17_l18-supply = <&vph>; + vdd_l19_l20-supply = <&vph>; + vdd_l21-supply = <&pm8058_s3>; + vdd_l22-supply = <&pm8058_s3>; + vdd_l23_l24_l25-supply = <&pm8058_s3>; + vdd_s0-supply = <&vph>; + vdd_s1-supply = <&vph>; + vdd_s2-supply = <&vph>; + vdd_s3-supply = <&vph>; + vdd_s4-supply = <&vph>; + vdd_ncp-supply = <&vph>; + + l0 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + l1 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + l2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <2600000>; + bias-pull-down; + }; + l3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + l4 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + l5 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + l6 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3600000>; + bias-pull-down; + }; + l7 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + l8 { + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <3050000>; + bias-pull-down; + }; + l9 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + l10 { + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <2600000>; + bias-pull-down; + }; + l11 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + bias-pull-down; + }; + l12 { + regulator-min-microvolt = <2900000>; + regulator-max-microvolt = <2900000>; + bias-pull-down; + }; + l13 { + regulator-min-microvolt = <2050000>; + regulator-max-microvolt = <2050000>; + bias-pull-down; + }; + l14 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + }; + l15 { + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + bias-pull-down; + }; + l16 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + regulator-always-on; + }; + l17 { + // 1.5V according to schematic + regulator-min-microvolt = <2600000>; + regulator-max-microvolt = <2600000>; + bias-pull-down; + }; + l18 { + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + bias-pull-down; + }; + l19 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + bias-pull-down; + }; + l20 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + bias-pull-down; + }; + l21 { + // 1.1 V according to schematic + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + regulator-always-on; + }; + l22 { + // 1.2 V according to schematic + regulator-min-microvolt = <1150000>; + regulator-max-microvolt = <1150000>; + bias-pull-down; + }; + l23 { + // Unused + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + l24 { + // Unused + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + l25 { + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + bias-pull-down; + }; + + s0 { + // regulator-min-microvolt = <500000>; + // regulator-max-microvolt = <1325000>; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + s1 { + // regulator-min-microvolt = <500000>; + // regulator-max-microvolt = <1250000>; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + s2 { + // 1.3 V according to schematic + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1400000>; + qcom,switch-mode-frequency = <1600000>; + bias-pull-down; + }; + s3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + qcom,switch-mode-frequency = <1600000>; + regulator-always-on; + bias-pull-down; + }; + s4 { + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + qcom,switch-mode-frequency = <1600000>; + regulator-always-on; + bias-pull-down; + }; + + /* LVS0 and LVS1 are just switches */ + lvs0 { + bias-pull-down; + }; + lvs1 { + bias-pull-down; + }; + + ncp { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + qcom,switch-mode-frequency = <1600000>; + }; + }; + }; + amba { + /* Internal 3.69 GiB eMMC */ + sdcc@12400000 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dragon_sdcc1_pins>; + vmmc-supply = <&pm8901_l5>; + vqmmc-supply = <&pm8901_lvs0>; + }; + + /* External micro SD card, directly connected, pulled up to 2.85 V */ + sdcc@12180000 { + status = "okay"; + /* Enable SSBI GPIO 22 as input, use for card detect */ + pinctrl-names = "default"; + pinctrl-0 = <&dragon_sdcc3_pins>, <&dragon_sdcc3_gpios>; + cd-gpios = <&pm8058_gpio 22 GPIO_ACTIVE_LOW>; + wp-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>; + vmmc-supply = <&pm8058_l14>; + }; + + /* + * Second external micro SD card, using two TXB104RGYR levelshifters + * to lift from 1.8 V to 2.85 V + */ + sdcc@12200000 { + status = "okay"; + /* Enable SSBI GPIO 26 as input, use for card detect */ + pinctrl-names = "default"; + pinctrl-0 = <&dragon_sdcc5_pins>, <&dragon_sdcc5_gpios>; + cd-gpios = <&pm8058_gpio 26 GPIO_ACTIVE_LOW>; + wp-gpios = <&tlmm 106 GPIO_ACTIVE_HIGH>; + vmmc-supply = <&pm8058_l14>; + vqmmc-supply = <&dragon_vio_txb>; + }; + }; + }; +}; -- cgit v1.2.3 From c3d5313001b0c8e9f70807e58438c3dcd30a4817 Mon Sep 17 00:00:00 2001 From: "twp@codeaurora.org" Date: Mon, 20 Jun 2016 11:19:23 -0700 Subject: dts: ipq4019: support ARMv7 PMU Add support for cortex-a7-pmu present on ipq4019 SoCs. Signed-off-by: Thomas Pedersen Signed-off-by: Andy Gross --- arch/arm/boot/dts/qcom-ipq4019.dtsi | 6 ++++++ 1 file changed, 6 insertions(+) (limited to 'arch') diff --git a/arch/arm/boot/dts/qcom-ipq4019.dtsi b/arch/arm/boot/dts/qcom-ipq4019.dtsi index 5c08d19066c2..a520ef5c9a94 100644 --- a/arch/arm/boot/dts/qcom-ipq4019.dtsi +++ b/arch/arm/boot/dts/qcom-ipq4019.dtsi @@ -84,6 +84,12 @@ }; }; + pmu { + compatible = "arm,cortex-a7-pmu"; + interrupts = ; + }; + clocks { sleep_clk: sleep_clk { compatible = "fixed-clock"; -- cgit v1.2.3