From cc30d60e4ca0b68e7e3f906eddd1e5b995d349f8 Mon Sep 17 00:00:00 2001 From: Linus Walleij Date: Sun, 4 Jan 2009 15:18:54 +0100 Subject: mmci: Add support for ST Micro derivate This patch adds support for the ST Microelectronics version of the PL180 PrimeCell. They use designer ID 0x80 and have a few alterations/bugfixes related to open drain and HW flow control. They also add some SDIO registers, I am unsure if these are in ST HW only or if this is things also added in later ARM revisions, but they are included in the mmci.h file for completeness. Signed-off-by: Linus Walleij Signed-off-by: Pierre Ossman --- drivers/mmc/host/mmci.c | 37 +++++++++++++++++++++++++++++++++---- 1 file changed, 33 insertions(+), 4 deletions(-) (limited to 'drivers/mmc/host/mmci.c') diff --git a/drivers/mmc/host/mmci.c b/drivers/mmc/host/mmci.c index 1bcbdd6763ac..2909bbc8ad00 100644 --- a/drivers/mmc/host/mmci.c +++ b/drivers/mmc/host/mmci.c @@ -430,6 +430,8 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) clk = 255; host->cclk = host->mclk / (2 * (clk + 1)); } + if (host->hw_designer == 0x80) + clk |= MCI_FCEN; /* Bug fix in ST IP block */ clk |= MCI_CLK_ENABLE; } @@ -440,15 +442,27 @@ static void mmci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios) case MMC_POWER_OFF: break; case MMC_POWER_UP: - pwr |= MCI_PWR_UP; - break; + /* The ST version does not have this, fall through to POWER_ON */ + if (host->hw_designer != 0x80) { + pwr |= MCI_PWR_UP; + break; + } case MMC_POWER_ON: pwr |= MCI_PWR_ON; break; } - if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) - pwr |= MCI_ROD; + if (ios->bus_mode == MMC_BUSMODE_OPENDRAIN) { + if (host->hw_designer != 0x80) + pwr |= MCI_ROD; + else { + /* + * The ST Micro variant use the ROD bit for something + * else and only has OD (Open Drain). + */ + pwr |= MCI_OD; + } + } writel(clk, host->base + MMCICLOCK); @@ -500,6 +514,12 @@ static int mmci_probe(struct amba_device *dev, void *id) } host = mmc_priv(mmc); + /* Bits 12 thru 19 is the designer */ + host->hw_designer = (dev->periphid >> 12) & 0xff; + /* Bits 20 thru 23 is the revison */ + host->hw_revision = (dev->periphid >> 20) & 0xf; + DBG(host, "designer ID = 0x%02x\n", host->hw_designer); + DBG(host, "revision = 0x%01x\n", host->hw_revision); host->clk = clk_get(&dev->dev, NULL); if (IS_ERR(host->clk)) { ret = PTR_ERR(host->clk); @@ -693,6 +713,15 @@ static struct amba_id mmci_ids[] = { .id = 0x00041181, .mask = 0x000fffff, }, + /* ST Micro variants */ + { + .id = 0x00180180, + .mask = 0x00ffffff, + }, + { + .id = 0x00280180, + .mask = 0x00ffffff, + }, { 0, 0 }, }; -- cgit v1.2.3