From 1f42adc8880d0692c3cb7b6adb247f17c4983081 Mon Sep 17 00:00:00 2001 From: Uwe Kleine-König Date: Tue, 10 Feb 2015 19:59:56 +0100 Subject: mtd: mxc-nand: Only enable hardware checksumming for fully detected flashes MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit At least on i.MX25 (i.e. NFCv2) preset_v2 is called with mtd->writesize == 0 that is before the connect flash chip is detected. It then configures for 8 bit ECC mode which needs 26 bytes of OOB per 512 bytes main section. For flashes with a smaller OOB area issuing a read page command makes the controller stuck with this config. Note that this currently doesn't hurt because the first read page command is issued only after detection is complete and preset is called once more. Signed-off-by: Uwe Kleine-König Signed-off-by: Brian Norris --- drivers/mtd/nand/mxc_nand.c | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-) (limited to 'drivers/mtd/nand') diff --git a/drivers/mtd/nand/mxc_nand.c b/drivers/mtd/nand/mxc_nand.c index 27ba07c07966..d9637ae34719 100644 --- a/drivers/mtd/nand/mxc_nand.c +++ b/drivers/mtd/nand/mxc_nand.c @@ -928,7 +928,7 @@ static void preset_v1(struct mtd_info *mtd) struct mxc_nand_host *host = nand_chip->priv; uint16_t config1 = 0; - if (nand_chip->ecc.mode == NAND_ECC_HW) + if (nand_chip->ecc.mode == NAND_ECC_HW && mtd->writesize) config1 |= NFC_V1_V2_CONFIG1_ECC_EN; if (!host->devtype_data->irqpending_quirk) @@ -956,9 +956,6 @@ static void preset_v2(struct mtd_info *mtd) struct mxc_nand_host *host = nand_chip->priv; uint16_t config1 = 0; - if (nand_chip->ecc.mode == NAND_ECC_HW) - config1 |= NFC_V1_V2_CONFIG1_ECC_EN; - config1 |= NFC_V2_CONFIG1_FP_INT; if (!host->devtype_data->irqpending_quirk) @@ -967,6 +964,9 @@ static void preset_v2(struct mtd_info *mtd) if (mtd->writesize) { uint16_t pages_per_block = mtd->erasesize / mtd->writesize; + if (nand_chip->ecc.mode == NAND_ECC_HW) + config1 |= NFC_V1_V2_CONFIG1_ECC_EN; + host->eccsize = get_eccsize(mtd); if (host->eccsize == 4) config1 |= NFC_V2_CONFIG1_ECC_MODE_4; @@ -1024,9 +1024,6 @@ static void preset_v3(struct mtd_info *mtd) NFC_V3_CONFIG2_INT_MSK | NFC_V3_CONFIG2_NUM_ADDR_PHASE0; - if (chip->ecc.mode == NAND_ECC_HW) - config2 |= NFC_V3_CONFIG2_ECC_EN; - addr_phases = fls(chip->pagemask) >> 3; if (mtd->writesize == 2048) { @@ -1041,6 +1038,9 @@ static void preset_v3(struct mtd_info *mtd) } if (mtd->writesize) { + if (chip->ecc.mode == NAND_ECC_HW) + config2 |= NFC_V3_CONFIG2_ECC_EN; + config2 |= NFC_V3_CONFIG2_PPB( ffs(mtd->erasesize / mtd->writesize) - 6, host->devtype_data->ppb_shift); -- cgit v1.2.3