From 89be0501a013737d562f56ce1c5a2ff075995b11 Mon Sep 17 00:00:00 2001 From: Sergei Shtylyov Date: Wed, 19 Apr 2006 22:46:21 +0400 Subject: [PATCH] au1000_eth.c probe code straightened up Straighten up the AMD Au1xx0 Ethernet probing code, make it print out (and store in the 'net_device' structure) the physical address of the controller, not the KSEG1-based virtual. Make the driver also claim/release the 4-byte MAC enable registers and assign to the Ethernet ports two consecutive MAC addresses to match those that are printed on their stickers. Signed-off-by: Sergei Shtylyov Signed-off-by: Jeff Garzik --- drivers/net/au1000_eth.c | 206 ++++++++++++++++++++--------------------------- 1 file changed, 87 insertions(+), 119 deletions(-) (limited to 'drivers/net/au1000_eth.c') diff --git a/drivers/net/au1000_eth.c b/drivers/net/au1000_eth.c index 1363083b4d83..d5dfc784bccd 100644 --- a/drivers/net/au1000_eth.c +++ b/drivers/net/au1000_eth.c @@ -2,7 +2,7 @@ * * Alchemy Au1x00 ethernet driver * - * Copyright 2001,2002,2003 MontaVista Software Inc. + * Copyright 2001-2003, 2006 MontaVista Software Inc. * Copyright 2002 TimeSys Corp. * Added ethtool/mii-tool support, * Copyright 2004 Matt Porter @@ -67,7 +67,7 @@ static int au1000_debug = 5; static int au1000_debug = 3; #endif -#define DRV_NAME "au1000eth" +#define DRV_NAME "au1000_eth" #define DRV_VERSION "1.5" #define DRV_AUTHOR "Pete Popov " #define DRV_DESC "Au1xxx on-chip Ethernet driver" @@ -79,7 +79,7 @@ MODULE_LICENSE("GPL"); // prototypes static void hard_stop(struct net_device *); static void enable_rx_tx(struct net_device *dev); -static struct net_device * au1000_probe(u32 ioaddr, int irq, int port_num); +static struct net_device * au1000_probe(int port_num); static int au1000_init(struct net_device *); static int au1000_open(struct net_device *); static int au1000_close(struct net_device *); @@ -1159,12 +1159,27 @@ setup_hw_rings(struct au1000_private *aup, u32 rx_base, u32 tx_base) } static struct { - int port; u32 base_addr; u32 macen_addr; int irq; struct net_device *dev; -} iflist[2]; +} iflist[2] = { +#ifdef CONFIG_SOC_AU1000 + {AU1000_ETH0_BASE, AU1000_MAC0_ENABLE, AU1000_MAC0_DMA_INT}, + {AU1000_ETH1_BASE, AU1000_MAC1_ENABLE, AU1000_MAC1_DMA_INT} +#endif +#ifdef CONFIG_SOC_AU1100 + {AU1100_ETH0_BASE, AU1100_MAC0_ENABLE, AU1100_MAC0_DMA_INT} +#endif +#ifdef CONFIG_SOC_AU1500 + {AU1500_ETH0_BASE, AU1500_MAC0_ENABLE, AU1500_MAC0_DMA_INT}, + {AU1500_ETH1_BASE, AU1500_MAC1_ENABLE, AU1500_MAC1_DMA_INT} +#endif +#ifdef CONFIG_SOC_AU1550 + {AU1550_ETH0_BASE, AU1550_MAC0_ENABLE, AU1550_MAC0_DMA_INT}, + {AU1550_ETH1_BASE, AU1550_MAC1_ENABLE, AU1550_MAC1_DMA_INT} +#endif +}; static int num_ifs; @@ -1175,58 +1190,14 @@ static int num_ifs; */ static int __init au1000_init_module(void) { - struct cpuinfo_mips *c = ¤t_cpu_data; int ni = (int)((au_readl(SYS_PINFUNC) & (u32)(SYS_PF_NI2)) >> 4); struct net_device *dev; int i, found_one = 0; - switch (c->cputype) { -#ifdef CONFIG_SOC_AU1000 - case CPU_AU1000: - num_ifs = 2 - ni; - iflist[0].base_addr = AU1000_ETH0_BASE; - iflist[1].base_addr = AU1000_ETH1_BASE; - iflist[0].macen_addr = AU1000_MAC0_ENABLE; - iflist[1].macen_addr = AU1000_MAC1_ENABLE; - iflist[0].irq = AU1000_MAC0_DMA_INT; - iflist[1].irq = AU1000_MAC1_DMA_INT; - break; -#endif -#ifdef CONFIG_SOC_AU1100 - case CPU_AU1100: - num_ifs = 1 - ni; - iflist[0].base_addr = AU1100_ETH0_BASE; - iflist[0].macen_addr = AU1100_MAC0_ENABLE; - iflist[0].irq = AU1100_MAC0_DMA_INT; - break; -#endif -#ifdef CONFIG_SOC_AU1500 - case CPU_AU1500: - num_ifs = 2 - ni; - iflist[0].base_addr = AU1500_ETH0_BASE; - iflist[1].base_addr = AU1500_ETH1_BASE; - iflist[0].macen_addr = AU1500_MAC0_ENABLE; - iflist[1].macen_addr = AU1500_MAC1_ENABLE; - iflist[0].irq = AU1500_MAC0_DMA_INT; - iflist[1].irq = AU1500_MAC1_DMA_INT; - break; -#endif -#ifdef CONFIG_SOC_AU1550 - case CPU_AU1550: - num_ifs = 2 - ni; - iflist[0].base_addr = AU1550_ETH0_BASE; - iflist[1].base_addr = AU1550_ETH1_BASE; - iflist[0].macen_addr = AU1550_MAC0_ENABLE; - iflist[1].macen_addr = AU1550_MAC1_ENABLE; - iflist[0].irq = AU1550_MAC0_DMA_INT; - iflist[1].irq = AU1550_MAC1_DMA_INT; - break; -#endif - default: - num_ifs = 0; - } + num_ifs = NUM_ETH_INTERFACES - ni; + for(i = 0; i < num_ifs; i++) { - dev = au1000_probe(iflist[i].base_addr, iflist[i].irq, i); + dev = au1000_probe(i); iflist[i].dev = dev; if (dev) found_one++; @@ -1435,8 +1406,7 @@ static struct ethtool_ops au1000_ethtool_ops = { .get_link = au1000_get_link }; -static struct net_device * -au1000_probe(u32 ioaddr, int irq, int port_num) +static struct net_device * au1000_probe(int port_num) { static unsigned version_printed = 0; struct au1000_private *aup = NULL; @@ -1444,94 +1414,95 @@ au1000_probe(u32 ioaddr, int irq, int port_num) db_dest_t *pDB, *pDBfree; char *pmac, *argptr; char ethaddr[6]; - int i, err; + int irq, i, err; + u32 base, macen; + + if (port_num >= NUM_ETH_INTERFACES) + return NULL; - if (!request_mem_region(CPHYSADDR(ioaddr), MAC_IOSIZE, "Au1x00 ENET")) + base = CPHYSADDR(iflist[port_num].base_addr ); + macen = CPHYSADDR(iflist[port_num].macen_addr); + irq = iflist[port_num].irq; + + if (!request_mem_region( base, MAC_IOSIZE, "Au1x00 ENET") || + !request_mem_region(macen, 4, "Au1x00 ENET")) return NULL; - if (version_printed++ == 0) + if (version_printed++ == 0) printk("%s version %s %s\n", DRV_NAME, DRV_VERSION, DRV_AUTHOR); dev = alloc_etherdev(sizeof(struct au1000_private)); if (!dev) { - printk (KERN_ERR "au1000 eth: alloc_etherdev failed\n"); + printk(KERN_ERR "%s: alloc_etherdev failed\n", DRV_NAME); return NULL; } - if ((err = register_netdev(dev))) { - printk(KERN_ERR "Au1x_eth Cannot register net device err %d\n", - err); + if ((err = register_netdev(dev)) != 0) { + printk(KERN_ERR "%s: Cannot register net device, error %d\n", + DRV_NAME, err); free_netdev(dev); return NULL; } - printk("%s: Au1x Ethernet found at 0x%x, irq %d\n", - dev->name, ioaddr, irq); + printk("%s: Au1xx0 Ethernet found at 0x%x, irq %d\n", + dev->name, base, irq); aup = dev->priv; /* Allocate the data buffers */ /* Snooping works fine with eth on all au1xxx */ - aup->vaddr = (u32)dma_alloc_noncoherent(NULL, - MAX_BUF_SIZE * (NUM_TX_BUFFS+NUM_RX_BUFFS), - &aup->dma_addr, - 0); + aup->vaddr = (u32)dma_alloc_noncoherent(NULL, MAX_BUF_SIZE * + (NUM_TX_BUFFS + NUM_RX_BUFFS), + &aup->dma_addr, 0); if (!aup->vaddr) { free_netdev(dev); - release_mem_region(CPHYSADDR(ioaddr), MAC_IOSIZE); + release_mem_region( base, MAC_IOSIZE); + release_mem_region(macen, 4); return NULL; } /* aup->mac is the base address of the MAC's registers */ - aup->mac = (volatile mac_reg_t *)((unsigned long)ioaddr); + aup->mac = (volatile mac_reg_t *)iflist[port_num].base_addr; + /* Setup some variables for quick register address access */ - if (ioaddr == iflist[0].base_addr) - { - /* check env variables first */ - if (!get_ethernet_addr(ethaddr)) { + aup->enable = (volatile u32 *)iflist[port_num].macen_addr; + aup->mac_id = port_num; + au_macs[port_num] = aup; + + if (port_num == 0) { + /* Check the environment variables first */ + if (get_ethernet_addr(ethaddr) == 0) memcpy(au1000_mac_addr, ethaddr, sizeof(au1000_mac_addr)); - } else { + else { /* Check command line */ argptr = prom_getcmdline(); - if ((pmac = strstr(argptr, "ethaddr=")) == NULL) { - printk(KERN_INFO "%s: No mac address found\n", - dev->name); - /* use the hard coded mac addresses */ - } else { + if ((pmac = strstr(argptr, "ethaddr=")) == NULL) + printk(KERN_INFO "%s: No MAC address found\n", + dev->name); + /* Use the hard coded MAC addresses */ + else { str2eaddr(ethaddr, pmac + strlen("ethaddr=")); memcpy(au1000_mac_addr, ethaddr, - sizeof(au1000_mac_addr)); + sizeof(au1000_mac_addr)); } } - aup->enable = (volatile u32 *) - ((unsigned long)iflist[0].macen_addr); - memcpy(dev->dev_addr, au1000_mac_addr, sizeof(au1000_mac_addr)); + setup_hw_rings(aup, MAC0_RX_DMA_ADDR, MAC0_TX_DMA_ADDR); - aup->mac_id = 0; - au_macs[0] = aup; - } - else - if (ioaddr == iflist[1].base_addr) - { - aup->enable = (volatile u32 *) - ((unsigned long)iflist[1].macen_addr); - memcpy(dev->dev_addr, au1000_mac_addr, sizeof(au1000_mac_addr)); - dev->dev_addr[4] += 0x10; + } else if (port_num == 1) setup_hw_rings(aup, MAC1_RX_DMA_ADDR, MAC1_TX_DMA_ADDR); - aup->mac_id = 1; - au_macs[1] = aup; - } - else - { - printk(KERN_ERR "%s: bad ioaddr\n", dev->name); - } - /* bring the device out of reset, otherwise probing the mii - * will hang */ + /* + * Assign to the Ethernet ports two consecutive MAC addresses + * to match those that are printed on their stickers + */ + memcpy(dev->dev_addr, au1000_mac_addr, sizeof(au1000_mac_addr)); + dev->dev_addr[5] += port_num; + + /* Bring the device out of reset, otherwise probing the MII will hang */ *aup->enable = MAC_EN_CLOCK_ENABLE; au_sync_delay(2); - *aup->enable = MAC_EN_RESET0 | MAC_EN_RESET1 | - MAC_EN_RESET2 | MAC_EN_CLOCK_ENABLE; + *aup->enable = MAC_EN_RESET0 | MAC_EN_RESET1 | MAC_EN_RESET2 | + MAC_EN_CLOCK_ENABLE; au_sync_delay(2); aup->mii = kmalloc(sizeof(struct mii_phy), GFP_KERNEL); @@ -1580,7 +1551,7 @@ au1000_probe(u32 ioaddr, int irq, int port_num) } spin_lock_init(&aup->lock); - dev->base_addr = ioaddr; + dev->base_addr = base; dev->irq = irq; dev->open = au1000_open; dev->hard_start_xmit = au1000_tx; @@ -1614,13 +1585,12 @@ err_out: if (aup->tx_db_inuse[i]) ReleaseDB(aup, aup->tx_db_inuse[i]); } - dma_free_noncoherent(NULL, - MAX_BUF_SIZE * (NUM_TX_BUFFS+NUM_RX_BUFFS), - (void *)aup->vaddr, - aup->dma_addr); + dma_free_noncoherent(NULL, MAX_BUF_SIZE * (NUM_TX_BUFFS + NUM_RX_BUFFS), + (void *)aup->vaddr, aup->dma_addr); unregister_netdev(dev); free_netdev(dev); - release_mem_region(CPHYSADDR(ioaddr), MAC_IOSIZE); + release_mem_region( base, MAC_IOSIZE); + release_mem_region(macen, 4); return NULL; } @@ -1805,20 +1775,18 @@ static void __exit au1000_cleanup_module(void) aup = (struct au1000_private *) dev->priv; unregister_netdev(dev); kfree(aup->mii); - for (j = 0; j < NUM_RX_DMA; j++) { + for (j = 0; j < NUM_RX_DMA; j++) if (aup->rx_db_inuse[j]) ReleaseDB(aup, aup->rx_db_inuse[j]); - } - for (j = 0; j < NUM_TX_DMA; j++) { + for (j = 0; j < NUM_TX_DMA; j++) if (aup->tx_db_inuse[j]) ReleaseDB(aup, aup->tx_db_inuse[j]); - } - dma_free_noncoherent(NULL, - MAX_BUF_SIZE * (NUM_TX_BUFFS+NUM_RX_BUFFS), - (void *)aup->vaddr, - aup->dma_addr); + dma_free_noncoherent(NULL, MAX_BUF_SIZE * + (NUM_TX_BUFFS + NUM_RX_BUFFS), + (void *)aup->vaddr, aup->dma_addr); + release_mem_region(dev->base_addr, MAC_IOSIZE); + release_mem_region(CPHYSADDR(iflist[i].macen_addr), 4); free_netdev(dev); - release_mem_region(CPHYSADDR(iflist[i].base_addr), MAC_IOSIZE); } } } -- cgit v1.2.3 From 0638dec01e89059c853515ab71c55fd13ba5a8ea Mon Sep 17 00:00:00 2001 From: Herbert Valerio Riedel Date: Thu, 1 Jun 2006 09:41:04 +0200 Subject: [PATCH] net: au1000_eth: PHY framework conversion convert au1000_eth driver to use PHY framework and garbage collected functions and identifiers that became unused/obsolete in the process Signed-off-by: Herbert Valerio Riedel Signed-off-by: Jeff Garzik --- drivers/net/Kconfig | 1 + drivers/net/au1000_eth.c | 1602 +++++++++++----------------------------------- drivers/net/au1000_eth.h | 134 +--- 3 files changed, 378 insertions(+), 1359 deletions(-) (limited to 'drivers/net/au1000_eth.c') diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig index 2f0b2549e9ec..20bdb9732a09 100644 --- a/drivers/net/Kconfig +++ b/drivers/net/Kconfig @@ -447,6 +447,7 @@ config MIPS_GT96100ETH config MIPS_AU1X00_ENET bool "MIPS AU1000 Ethernet support" depends on NET_ETHERNET && SOC_AU1X00 + select PHYLIB select CRC32 help If you have an Alchemy Semi AU1X00 based system diff --git a/drivers/net/au1000_eth.c b/drivers/net/au1000_eth.c index e1fe960d71b3..038d5fcb15e6 100644 --- a/drivers/net/au1000_eth.c +++ b/drivers/net/au1000_eth.c @@ -9,6 +9,9 @@ * Update: 2004 Bjoern Riemer, riemer@fokus.fraunhofer.de * or riemer@riemer-nt.de: fixed the link beat detection with * ioctls (SIOCGMIIPHY) + * Copyright 2006 Herbert Valerio Riedel + * converted to use linux-2.6.x's PHY framework + * * Author: MontaVista Software, Inc. * ppopov@mvista.com or source@mvista.com * @@ -53,6 +56,7 @@ #include #include #include +#include #include #include #include @@ -88,17 +92,15 @@ static int au1000_tx(struct sk_buff *, struct net_device *); static int au1000_rx(struct net_device *); static irqreturn_t au1000_interrupt(int, void *, struct pt_regs *); static void au1000_tx_timeout(struct net_device *); -static int au1000_set_config(struct net_device *dev, struct ifmap *map); static void set_rx_mode(struct net_device *); static struct net_device_stats *au1000_get_stats(struct net_device *); -static void au1000_timer(unsigned long); static int au1000_ioctl(struct net_device *, struct ifreq *, int); static int mdio_read(struct net_device *, int, int); static void mdio_write(struct net_device *, int, int, u16); -static void dump_mii(struct net_device *dev, int phy_id); +static void au1000_adjust_link(struct net_device *); +static void enable_mac(struct net_device *, int); // externs -extern void ack_rise_edge_irq(unsigned int); extern int get_ethernet_addr(char *ethernet_addr); extern void str2eaddr(unsigned char *ea, unsigned char *str); extern char * __init prom_getcmdline(void); @@ -126,705 +128,83 @@ static unsigned char au1000_mac_addr[6] __devinitdata = { 0x00, 0x50, 0xc2, 0x0c, 0x30, 0x00 }; -#define nibswap(x) ((((x) >> 4) & 0x0f) | (((x) << 4) & 0xf0)) -#define RUN_AT(x) (jiffies + (x)) - -// For reading/writing 32-bit words from/to DMA memory -#define cpu_to_dma32 cpu_to_be32 -#define dma32_to_cpu be32_to_cpu - struct au1000_private *au_macs[NUM_ETH_INTERFACES]; -/* FIXME - * All of the PHY code really should be detached from the MAC - * code. +/* + * board-specific configurations + * + * PHY detection algorithm + * + * If AU1XXX_PHY_STATIC_CONFIG is undefined, the PHY setup is + * autodetected: + * + * mii_probe() first searches the current MAC's MII bus for a PHY, + * selecting the first (or last, if AU1XXX_PHY_SEARCH_HIGHEST_ADDR is + * defined) PHY address not already claimed by another netdev. + * + * If nothing was found that way when searching for the 2nd ethernet + * controller's PHY and AU1XXX_PHY1_SEARCH_ON_MAC0 is defined, then + * the first MII bus is searched as well for an unclaimed PHY; this is + * needed in case of a dual-PHY accessible only through the MAC0's MII + * bus. + * + * Finally, if no PHY is found, then the corresponding ethernet + * controller is not registered to the network subsystem. */ -/* Default advertise */ -#define GENMII_DEFAULT_ADVERTISE \ - ADVERTISED_10baseT_Half | ADVERTISED_10baseT_Full | \ - ADVERTISED_100baseT_Half | ADVERTISED_100baseT_Full | \ - ADVERTISED_Autoneg - -#define GENMII_DEFAULT_FEATURES \ - SUPPORTED_10baseT_Half | SUPPORTED_10baseT_Full | \ - SUPPORTED_100baseT_Half | SUPPORTED_100baseT_Full | \ - SUPPORTED_Autoneg - -int bcm_5201_init(struct net_device *dev, int phy_addr) -{ - s16 data; - - /* Stop auto-negotiation */ - data = mdio_read(dev, phy_addr, MII_CONTROL); - mdio_write(dev, phy_addr, MII_CONTROL, data & ~MII_CNTL_AUTO); - - /* Set advertisement to 10/100 and Half/Full duplex - * (full capabilities) */ - data = mdio_read(dev, phy_addr, MII_ANADV); - data |= MII_NWAY_TX | MII_NWAY_TX_FDX | MII_NWAY_T_FDX | MII_NWAY_T; - mdio_write(dev, phy_addr, MII_ANADV, data); - - /* Restart auto-negotiation */ - data = mdio_read(dev, phy_addr, MII_CONTROL); - data |= MII_CNTL_RST_AUTO | MII_CNTL_AUTO; - mdio_write(dev, phy_addr, MII_CONTROL, data); - - if (au1000_debug > 4) - dump_mii(dev, phy_addr); - return 0; -} - -int bcm_5201_reset(struct net_device *dev, int phy_addr) -{ - s16 mii_control, timeout; - - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - mdio_write(dev, phy_addr, MII_CONTROL, mii_control | MII_CNTL_RESET); - mdelay(1); - for (timeout = 100; timeout > 0; --timeout) { - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - if ((mii_control & MII_CNTL_RESET) == 0) - break; - mdelay(1); - } - if (mii_control & MII_CNTL_RESET) { - printk(KERN_ERR "%s PHY reset timeout !\n", dev->name); - return -1; - } - return 0; -} - -int -bcm_5201_status(struct net_device *dev, int phy_addr, u16 *link, u16 *speed) -{ - u16 mii_data; - struct au1000_private *aup; - - if (!dev) { - printk(KERN_ERR "bcm_5201_status error: NULL dev\n"); - return -1; - } - aup = (struct au1000_private *) dev->priv; - - mii_data = mdio_read(dev, aup->phy_addr, MII_STATUS); - if (mii_data & MII_STAT_LINK) { - *link = 1; - mii_data = mdio_read(dev, aup->phy_addr, MII_AUX_CNTRL); - if (mii_data & MII_AUX_100) { - if (mii_data & MII_AUX_FDX) { - *speed = IF_PORT_100BASEFX; - dev->if_port = IF_PORT_100BASEFX; - } - else { - *speed = IF_PORT_100BASETX; - dev->if_port = IF_PORT_100BASETX; - } - } - else { - *speed = IF_PORT_10BASET; - dev->if_port = IF_PORT_10BASET; - } - - } - else { - *link = 0; - *speed = 0; - dev->if_port = IF_PORT_UNKNOWN; - } - return 0; -} - -int lsi_80227_init(struct net_device *dev, int phy_addr) -{ - if (au1000_debug > 4) - printk("lsi_80227_init\n"); - - /* restart auto-negotiation */ - mdio_write(dev, phy_addr, MII_CONTROL, - MII_CNTL_F100 | MII_CNTL_AUTO | MII_CNTL_RST_AUTO); // | MII_CNTL_FDX); - mdelay(1); - - /* set up LEDs to correct display */ -#ifdef CONFIG_MIPS_MTX1 - mdio_write(dev, phy_addr, 17, 0xff80); -#else - mdio_write(dev, phy_addr, 17, 0xffc0); -#endif - - if (au1000_debug > 4) - dump_mii(dev, phy_addr); - return 0; -} - -int lsi_80227_reset(struct net_device *dev, int phy_addr) -{ - s16 mii_control, timeout; - - if (au1000_debug > 4) { - printk("lsi_80227_reset\n"); - dump_mii(dev, phy_addr); - } - - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - mdio_write(dev, phy_addr, MII_CONTROL, mii_control | MII_CNTL_RESET); - mdelay(1); - for (timeout = 100; timeout > 0; --timeout) { - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - if ((mii_control & MII_CNTL_RESET) == 0) - break; - mdelay(1); - } - if (mii_control & MII_CNTL_RESET) { - printk(KERN_ERR "%s PHY reset timeout !\n", dev->name); - return -1; - } - return 0; -} - -int -lsi_80227_status(struct net_device *dev, int phy_addr, u16 *link, u16 *speed) -{ - u16 mii_data; - struct au1000_private *aup; - - if (!dev) { - printk(KERN_ERR "lsi_80227_status error: NULL dev\n"); - return -1; - } - aup = (struct au1000_private *) dev->priv; - - mii_data = mdio_read(dev, aup->phy_addr, MII_STATUS); - if (mii_data & MII_STAT_LINK) { - *link = 1; - mii_data = mdio_read(dev, aup->phy_addr, MII_LSI_PHY_STAT); - if (mii_data & MII_LSI_PHY_STAT_SPD) { - if (mii_data & MII_LSI_PHY_STAT_FDX) { - *speed = IF_PORT_100BASEFX; - dev->if_port = IF_PORT_100BASEFX; - } - else { - *speed = IF_PORT_100BASETX; - dev->if_port = IF_PORT_100BASETX; - } - } - else { - *speed = IF_PORT_10BASET; - dev->if_port = IF_PORT_10BASET; - } - - } - else { - *link = 0; - *speed = 0; - dev->if_port = IF_PORT_UNKNOWN; - } - return 0; -} - -int am79c901_init(struct net_device *dev, int phy_addr) -{ - printk("am79c901_init\n"); - return 0; -} - -int am79c901_reset(struct net_device *dev, int phy_addr) -{ - printk("am79c901_reset\n"); - return 0; -} - -int -am79c901_status(struct net_device *dev, int phy_addr, u16 *link, u16 *speed) -{ - return 0; -} - -int am79c874_init(struct net_device *dev, int phy_addr) -{ - s16 data; - - /* 79c874 has quit resembled bit assignments to BCM5201 */ - if (au1000_debug > 4) - printk("am79c847_init\n"); - - /* Stop auto-negotiation */ - data = mdio_read(dev, phy_addr, MII_CONTROL); - mdio_write(dev, phy_addr, MII_CONTROL, data & ~MII_CNTL_AUTO); - - /* Set advertisement to 10/100 and Half/Full duplex - * (full capabilities) */ - data = mdio_read(dev, phy_addr, MII_ANADV); - data |= MII_NWAY_TX | MII_NWAY_TX_FDX | MII_NWAY_T_FDX | MII_NWAY_T; - mdio_write(dev, phy_addr, MII_ANADV, data); - - /* Restart auto-negotiation */ - data = mdio_read(dev, phy_addr, MII_CONTROL); - data |= MII_CNTL_RST_AUTO | MII_CNTL_AUTO; - - mdio_write(dev, phy_addr, MII_CONTROL, data); - - if (au1000_debug > 4) dump_mii(dev, phy_addr); - return 0; -} - -int am79c874_reset(struct net_device *dev, int phy_addr) -{ - s16 mii_control, timeout; - - if (au1000_debug > 4) - printk("am79c874_reset\n"); - - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - mdio_write(dev, phy_addr, MII_CONTROL, mii_control | MII_CNTL_RESET); - mdelay(1); - for (timeout = 100; timeout > 0; --timeout) { - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - if ((mii_control & MII_CNTL_RESET) == 0) - break; - mdelay(1); - } - if (mii_control & MII_CNTL_RESET) { - printk(KERN_ERR "%s PHY reset timeout !\n", dev->name); - return -1; - } - return 0; -} - -int -am79c874_status(struct net_device *dev, int phy_addr, u16 *link, u16 *speed) -{ - u16 mii_data; - struct au1000_private *aup; - - // printk("am79c874_status\n"); - if (!dev) { - printk(KERN_ERR "am79c874_status error: NULL dev\n"); - return -1; - } - - aup = (struct au1000_private *) dev->priv; - mii_data = mdio_read(dev, aup->phy_addr, MII_STATUS); +/* autodetection defaults */ +#undef AU1XXX_PHY_SEARCH_HIGHEST_ADDR +#define AU1XXX_PHY1_SEARCH_ON_MAC0 - if (mii_data & MII_STAT_LINK) { - *link = 1; - mii_data = mdio_read(dev, aup->phy_addr, MII_AMD_PHY_STAT); - if (mii_data & MII_AMD_PHY_STAT_SPD) { - if (mii_data & MII_AMD_PHY_STAT_FDX) { - *speed = IF_PORT_100BASEFX; - dev->if_port = IF_PORT_100BASEFX; - } - else { - *speed = IF_PORT_100BASETX; - dev->if_port = IF_PORT_100BASETX; - } - } - else { - *speed = IF_PORT_10BASET; - dev->if_port = IF_PORT_10BASET; - } - - } - else { - *link = 0; - *speed = 0; - dev->if_port = IF_PORT_UNKNOWN; - } - return 0; -} - -int lxt971a_init(struct net_device *dev, int phy_addr) -{ - if (au1000_debug > 4) - printk("lxt971a_init\n"); - - /* restart auto-negotiation */ - mdio_write(dev, phy_addr, MII_CONTROL, - MII_CNTL_F100 | MII_CNTL_AUTO | MII_CNTL_RST_AUTO | MII_CNTL_FDX); - - /* set up LEDs to correct display */ - mdio_write(dev, phy_addr, 20, 0x0422); - - if (au1000_debug > 4) - dump_mii(dev, phy_addr); - return 0; -} - -int lxt971a_reset(struct net_device *dev, int phy_addr) -{ - s16 mii_control, timeout; - - if (au1000_debug > 4) { - printk("lxt971a_reset\n"); - dump_mii(dev, phy_addr); - } - - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - mdio_write(dev, phy_addr, MII_CONTROL, mii_control | MII_CNTL_RESET); - mdelay(1); - for (timeout = 100; timeout > 0; --timeout) { - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - if ((mii_control & MII_CNTL_RESET) == 0) - break; - mdelay(1); - } - if (mii_control & MII_CNTL_RESET) { - printk(KERN_ERR "%s PHY reset timeout !\n", dev->name); - return -1; - } - return 0; -} - -int -lxt971a_status(struct net_device *dev, int phy_addr, u16 *link, u16 *speed) -{ - u16 mii_data; - struct au1000_private *aup; - - if (!dev) { - printk(KERN_ERR "lxt971a_status error: NULL dev\n"); - return -1; - } - aup = (struct au1000_private *) dev->priv; - - mii_data = mdio_read(dev, aup->phy_addr, MII_STATUS); - if (mii_data & MII_STAT_LINK) { - *link = 1; - mii_data = mdio_read(dev, aup->phy_addr, MII_INTEL_PHY_STAT); - if (mii_data & MII_INTEL_PHY_STAT_SPD) { - if (mii_data & MII_INTEL_PHY_STAT_FDX) { - *speed = IF_PORT_100BASEFX; - dev->if_port = IF_PORT_100BASEFX; - } - else { - *speed = IF_PORT_100BASETX; - dev->if_port = IF_PORT_100BASETX; - } - } - else { - *speed = IF_PORT_10BASET; - dev->if_port = IF_PORT_10BASET; - } - - } - else { - *link = 0; - *speed = 0; - dev->if_port = IF_PORT_UNKNOWN; - } - return 0; -} - -int ks8995m_init(struct net_device *dev, int phy_addr) -{ - s16 data; - -// printk("ks8995m_init\n"); - /* Stop auto-negotiation */ - data = mdio_read(dev, phy_addr, MII_CONTROL); - mdio_write(dev, phy_addr, MII_CONTROL, data & ~MII_CNTL_AUTO); - - /* Set advertisement to 10/100 and Half/Full duplex - * (full capabilities) */ - data = mdio_read(dev, phy_addr, MII_ANADV); - data |= MII_NWAY_TX | MII_NWAY_TX_FDX | MII_NWAY_T_FDX | MII_NWAY_T; - mdio_write(dev, phy_addr, MII_ANADV, data); - - /* Restart auto-negotiation */ - data = mdio_read(dev, phy_addr, MII_CONTROL); - data |= MII_CNTL_RST_AUTO | MII_CNTL_AUTO; - mdio_write(dev, phy_addr, MII_CONTROL, data); - - if (au1000_debug > 4) dump_mii(dev, phy_addr); - - return 0; -} - -int ks8995m_reset(struct net_device *dev, int phy_addr) -{ - s16 mii_control, timeout; - -// printk("ks8995m_reset\n"); - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - mdio_write(dev, phy_addr, MII_CONTROL, mii_control | MII_CNTL_RESET); - mdelay(1); - for (timeout = 100; timeout > 0; --timeout) { - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - if ((mii_control & MII_CNTL_RESET) == 0) - break; - mdelay(1); - } - if (mii_control & MII_CNTL_RESET) { - printk(KERN_ERR "%s PHY reset timeout !\n", dev->name); - return -1; - } - return 0; -} - -int ks8995m_status(struct net_device *dev, int phy_addr, u16 *link, u16 *speed) -{ - u16 mii_data; - struct au1000_private *aup; - - if (!dev) { - printk(KERN_ERR "ks8995m_status error: NULL dev\n"); - return -1; - } - aup = (struct au1000_private *) dev->priv; - - mii_data = mdio_read(dev, aup->phy_addr, MII_STATUS); - if (mii_data & MII_STAT_LINK) { - *link = 1; - mii_data = mdio_read(dev, aup->phy_addr, MII_AUX_CNTRL); - if (mii_data & MII_AUX_100) { - if (mii_data & MII_AUX_FDX) { - *speed = IF_PORT_100BASEFX; - dev->if_port = IF_PORT_100BASEFX; - } - else { - *speed = IF_PORT_100BASETX; - dev->if_port = IF_PORT_100BASETX; - } - } - else { - *speed = IF_PORT_10BASET; - dev->if_port = IF_PORT_10BASET; - } - - } - else { - *link = 0; - *speed = 0; - dev->if_port = IF_PORT_UNKNOWN; - } - return 0; -} - -int -smsc_83C185_init (struct net_device *dev, int phy_addr) -{ - s16 data; - - if (au1000_debug > 4) - printk("smsc_83C185_init\n"); - - /* Stop auto-negotiation */ - data = mdio_read(dev, phy_addr, MII_CONTROL); - mdio_write(dev, phy_addr, MII_CONTROL, data & ~MII_CNTL_AUTO); - - /* Set advertisement to 10/100 and Half/Full duplex - * (full capabilities) */ - data = mdio_read(dev, phy_addr, MII_ANADV); - data |= MII_NWAY_TX | MII_NWAY_TX_FDX | MII_NWAY_T_FDX | MII_NWAY_T; - mdio_write(dev, phy_addr, MII_ANADV, data); - - /* Restart auto-negotiation */ - data = mdio_read(dev, phy_addr, MII_CONTROL); - data |= MII_CNTL_RST_AUTO | MII_CNTL_AUTO; - - mdio_write(dev, phy_addr, MII_CONTROL, data); - - if (au1000_debug > 4) dump_mii(dev, phy_addr); - return 0; -} - -int -smsc_83C185_reset (struct net_device *dev, int phy_addr) -{ - s16 mii_control, timeout; - - if (au1000_debug > 4) - printk("smsc_83C185_reset\n"); - - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - mdio_write(dev, phy_addr, MII_CONTROL, mii_control | MII_CNTL_RESET); - mdelay(1); - for (timeout = 100; timeout > 0; --timeout) { - mii_control = mdio_read(dev, phy_addr, MII_CONTROL); - if ((mii_control & MII_CNTL_RESET) == 0) - break; - mdelay(1); - } - if (mii_control & MII_CNTL_RESET) { - printk(KERN_ERR "%s PHY reset timeout !\n", dev->name); - return -1; - } - return 0; -} - -int -smsc_83C185_status (struct net_device *dev, int phy_addr, u16 *link, u16 *speed) -{ - u16 mii_data; - struct au1000_private *aup; - - if (!dev) { - printk(KERN_ERR "smsc_83C185_status error: NULL dev\n"); - return -1; - } - - aup = (struct au1000_private *) dev->priv; - mii_data = mdio_read(dev, aup->phy_addr, MII_STATUS); - - if (mii_data & MII_STAT_LINK) { - *link = 1; - mii_data = mdio_read(dev, aup->phy_addr, 0x1f); - if (mii_data & (1<<3)) { - if (mii_data & (1<<4)) { - *speed = IF_PORT_100BASEFX; - dev->if_port = IF_PORT_100BASEFX; - } - else { - *speed = IF_PORT_100BASETX; - dev->if_port = IF_PORT_100BASETX; - } - } - else { - *speed = IF_PORT_10BASET; - dev->if_port = IF_PORT_10BASET; - } - } - else { - *link = 0; - *speed = 0; - dev->if_port = IF_PORT_UNKNOWN; - } - return 0; -} - - -#ifdef CONFIG_MIPS_BOSPORUS -int stub_init(struct net_device *dev, int phy_addr) -{ - //printk("PHY stub_init\n"); - return 0; -} - -int stub_reset(struct net_device *dev, int phy_addr) -{ - //printk("PHY stub_reset\n"); - return 0; -} - -int -stub_status(struct net_device *dev, int phy_addr, u16 *link, u16 *speed) -{ - //printk("PHY stub_status\n"); - *link = 1; - /* hmmm, revisit */ - *speed = IF_PORT_100BASEFX; - dev->if_port = IF_PORT_100BASEFX; - return 0; -} -#endif - -struct phy_ops bcm_5201_ops = { - bcm_5201_init, - bcm_5201_reset, - bcm_5201_status, -}; - -struct phy_ops am79c874_ops = { - am79c874_init, - am79c874_reset, - am79c874_status, -}; - -struct phy_ops am79c901_ops = { - am79c901_init, - am79c901_reset, - am79c901_status, -}; - -struct phy_ops lsi_80227_ops = { - lsi_80227_init, - lsi_80227_reset, - lsi_80227_status, -}; - -struct phy_ops lxt971a_ops = { - lxt971a_init, - lxt971a_reset, - lxt971a_status, -}; +/* static PHY setup + * + * most boards PHY setup should be detectable properly with the + * autodetection algorithm in mii_probe(), but in some cases (e.g. if + * you have a switch attached, or want to use the PHY's interrupt + * notification capabilities) you can provide a static PHY + * configuration here + * + * IRQs may only be set, if a PHY address was configured + * If a PHY address is given, also a bus id is required to be set + * + * ps: make sure the used irqs are configured properly in the board + * specific irq-map + */ -struct phy_ops ks8995m_ops = { - ks8995m_init, - ks8995m_reset, - ks8995m_status, -}; +#if defined(CONFIG_MIPS_BOSPORUS) +/* + * Micrel/Kendin 5 port switch attached to MAC0, + * MAC0 is associated with PHY address 5 (== WAN port) + * MAC1 is not associated with any PHY, since it's connected directly + * to the switch. + * no interrupts are used + */ +# define AU1XXX_PHY_STATIC_CONFIG -struct phy_ops smsc_83C185_ops = { - smsc_83C185_init, - smsc_83C185_reset, - smsc_83C185_status, -}; +# define AU1XXX_PHY0_ADDR 5 +# define AU1XXX_PHY0_BUSID 0 +# undef AU1XXX_PHY0_IRQ -#ifdef CONFIG_MIPS_BOSPORUS -struct phy_ops stub_ops = { - stub_init, - stub_reset, - stub_status, -}; +# undef AU1XXX_PHY1_ADDR +# undef AU1XXX_PHY1_BUSID +# undef AU1XXX_PHY1_IRQ #endif -static struct mii_chip_info { - const char * name; - u16 phy_id0; - u16 phy_id1; - struct phy_ops *phy_ops; - int dual_phy; -} mii_chip_table[] = { - {"Broadcom BCM5201 10/100 BaseT PHY",0x0040,0x6212, &bcm_5201_ops,0}, - {"Broadcom BCM5221 10/100 BaseT PHY",0x0040,0x61e4, &bcm_5201_ops,0}, - {"Broadcom BCM5222 10/100 BaseT PHY",0x0040,0x6322, &bcm_5201_ops,1}, - {"NS DP83847 PHY", 0x2000, 0x5c30, &bcm_5201_ops ,0}, - {"AMD 79C901 HomePNA PHY",0x0000,0x35c8, &am79c901_ops,0}, - {"AMD 79C874 10/100 BaseT PHY",0x0022,0x561b, &am79c874_ops,0}, - {"LSI 80227 10/100 BaseT PHY",0x0016,0xf840, &lsi_80227_ops,0}, - {"Intel LXT971A Dual Speed PHY",0x0013,0x78e2, &lxt971a_ops,0}, - {"Kendin KS8995M 10/100 BaseT PHY",0x0022,0x1450, &ks8995m_ops,0}, - {"SMSC LAN83C185 10/100 BaseT PHY",0x0007,0xc0a3, &smsc_83C185_ops,0}, -#ifdef CONFIG_MIPS_BOSPORUS - {"Stub", 0x1234, 0x5678, &stub_ops }, +#if defined(AU1XXX_PHY0_BUSID) && (AU1XXX_PHY0_BUSID > 0) +# error MAC0-associated PHY attached 2nd MACs MII bus not supported yet #endif - {0,}, -}; -static int mdio_read(struct net_device *dev, int phy_id, int reg) +/* + * MII operations + */ +static int mdio_read(struct net_device *dev, int phy_addr, int reg) { struct au1000_private *aup = (struct au1000_private *) dev->priv; - volatile u32 *mii_control_reg; - volatile u32 *mii_data_reg; + volatile u32 *const mii_control_reg = &aup->mac->mii_control; + volatile u32 *const mii_data_reg = &aup->mac->mii_data; u32 timedout = 20; u32 mii_control; - #ifdef CONFIG_BCM5222_DUAL_PHY - /* First time we probe, it's for the mac0 phy. - * Since we haven't determined yet that we have a dual phy, - * aup->mii->mii_control_reg won't be setup and we'll - * default to the else statement. - * By the time we probe for the mac1 phy, the mii_control_reg - * will be setup to be the address of the mac0 phy control since - * both phys are controlled through mac0. - */ - if (aup->mii && aup->mii->mii_control_reg) { - mii_control_reg = aup->mii->mii_control_reg; - mii_data_reg = aup->mii->mii_data_reg; - } - else if (au_macs[0]->mii && au_macs[0]->mii->mii_control_reg) { - /* assume both phys are controlled through mac0 */ - mii_control_reg = au_macs[0]->mii->mii_control_reg; - mii_data_reg = au_macs[0]->mii->mii_data_reg; - } - else - #endif - { - /* default control and data reg addresses */ - mii_control_reg = &aup->mac->mii_control; - mii_data_reg = &aup->mac->mii_data; - } - while (*mii_control_reg & MAC_MII_BUSY) { mdelay(1); if (--timedout == 0) { @@ -835,7 +215,7 @@ static int mdio_read(struct net_device *dev, int phy_id, int reg) } mii_control = MAC_SET_MII_SELECT_REG(reg) | - MAC_SET_MII_SELECT_PHY(phy_id) | MAC_MII_READ; + MAC_SET_MII_SELECT_PHY(phy_addr) | MAC_MII_READ; *mii_control_reg = mii_control; @@ -851,32 +231,14 @@ static int mdio_read(struct net_device *dev, int phy_id, int reg) return (int)*mii_data_reg; } -static void mdio_write(struct net_device *dev, int phy_id, int reg, u16 value) +static void mdio_write(struct net_device *dev, int phy_addr, int reg, u16 value) { struct au1000_private *aup = (struct au1000_private *) dev->priv; - volatile u32 *mii_control_reg; - volatile u32 *mii_data_reg; + volatile u32 *const mii_control_reg = &aup->mac->mii_control; + volatile u32 *const mii_data_reg = &aup->mac->mii_data; u32 timedout = 20; u32 mii_control; - #ifdef CONFIG_BCM5222_DUAL_PHY - if (aup->mii && aup->mii->mii_control_reg) { - mii_control_reg = aup->mii->mii_control_reg; - mii_data_reg = aup->mii->mii_data_reg; - } - else if (au_macs[0]->mii && au_macs[0]->mii->mii_control_reg) { - /* assume both phys are controlled through mac0 */ - mii_control_reg = au_macs[0]->mii->mii_control_reg; - mii_data_reg = au_macs[0]->mii->mii_data_reg; - } - else - #endif - { - /* default control and data reg addresses */ - mii_control_reg = &aup->mac->mii_control; - mii_data_reg = &aup->mac->mii_data; - } - while (*mii_control_reg & MAC_MII_BUSY) { mdelay(1); if (--timedout == 0) { @@ -887,165 +249,145 @@ static void mdio_write(struct net_device *dev, int phy_id, int reg, u16 value) } mii_control = MAC_SET_MII_SELECT_REG(reg) | - MAC_SET_MII_SELECT_PHY(phy_id) | MAC_MII_WRITE; + MAC_SET_MII_SELECT_PHY(phy_addr) | MAC_MII_WRITE; *mii_data_reg = value; *mii_control_reg = mii_control; } +static int mdiobus_read(struct mii_bus *bus, int phy_addr, int regnum) +{ + /* WARNING: bus->phy_map[phy_addr].attached_dev == dev does + * _NOT_ hold (e.g. when PHY is accessed through other MAC's MII bus) */ + struct net_device *const dev = bus->priv; + + enable_mac(dev, 0); /* make sure the MAC associated with this + * mii_bus is enabled */ + return mdio_read(dev, phy_addr, regnum); +} -static void dump_mii(struct net_device *dev, int phy_id) +static int mdiobus_write(struct mii_bus *bus, int phy_addr, int regnum, + u16 value) { - int i, val; + struct net_device *const dev = bus->priv; - for (i = 0; i < 7; i++) { - if ((val = mdio_read(dev, phy_id, i)) >= 0) - printk("%s: MII Reg %d=%x\n", dev->name, i, val); - } - for (i = 16; i < 25; i++) { - if ((val = mdio_read(dev, phy_id, i)) >= 0) - printk("%s: MII Reg %d=%x\n", dev->name, i, val); - } + enable_mac(dev, 0); /* make sure the MAC associated with this + * mii_bus is enabled */ + mdio_write(dev, phy_addr, regnum, value); + return 0; } -static int mii_probe (struct net_device * dev) +static int mdiobus_reset(struct mii_bus *bus) { - struct au1000_private *aup = (struct au1000_private *) dev->priv; - int phy_addr; -#ifdef CONFIG_MIPS_BOSPORUS - int phy_found=0; -#endif + struct net_device *const dev = bus->priv; - /* search for total of 32 possible mii phy addresses */ - for (phy_addr = 0; phy_addr < 32; phy_addr++) { - u16 mii_status; - u16 phy_id0, phy_id1; - int i; + enable_mac(dev, 0); /* make sure the MAC associated with this + * mii_bus is enabled */ + return 0; +} - #ifdef CONFIG_BCM5222_DUAL_PHY - /* Mask the already found phy, try next one */ - if (au_macs[0]->mii && au_macs[0]->mii->mii_control_reg) { - if (au_macs[0]->phy_addr == phy_addr) - continue; - } - #endif - - mii_status = mdio_read(dev, phy_addr, MII_STATUS); - if (mii_status == 0xffff || mii_status == 0x0000) - /* the mii is not accessable, try next one */ - continue; - - phy_id0 = mdio_read(dev, phy_addr, MII_PHY_ID0); - phy_id1 = mdio_read(dev, phy_addr, MII_PHY_ID1); - - /* search our mii table for the current mii */ - for (i = 0; mii_chip_table[i].phy_id1; i++) { - if (phy_id0 == mii_chip_table[i].phy_id0 && - phy_id1 == mii_chip_table[i].phy_id1) { - struct mii_phy * mii_phy = aup->mii; - - printk(KERN_INFO "%s: %s at phy address %d\n", - dev->name, mii_chip_table[i].name, - phy_addr); -#ifdef CONFIG_MIPS_BOSPORUS - phy_found = 1; -#endif - mii_phy->chip_info = mii_chip_table+i; - aup->phy_addr = phy_addr; - aup->want_autoneg = 1; - aup->phy_ops = mii_chip_table[i].phy_ops; - aup->phy_ops->phy_init(dev,phy_addr); - - // Check for dual-phy and then store required - // values and set indicators. We need to do - // this now since mdio_{read,write} need the - // control and data register addresses. - #ifdef CONFIG_BCM5222_DUAL_PHY - if ( mii_chip_table[i].dual_phy) { - - /* assume both phys are controlled - * through MAC0. Board specific? */ - - /* sanity check */ - if (!au_macs[0] || !au_macs[0]->mii) - return -1; - aup->mii->mii_control_reg = (u32 *) - &au_macs[0]->mac->mii_control; - aup->mii->mii_data_reg = (u32 *) - &au_macs[0]->mac->mii_data; - } - #endif - goto found; - } +static int mii_probe (struct net_device *dev) +{ + struct au1000_private *const aup = (struct au1000_private *) dev->priv; + struct phy_device *phydev = NULL; + +#if defined(AU1XXX_PHY_STATIC_CONFIG) + BUG_ON(aup->mac_id < 0 || aup->mac_id > 1); + + if(aup->mac_id == 0) { /* get PHY0 */ +# if defined(AU1XXX_PHY0_ADDR) + phydev = au_macs[AU1XXX_PHY0_BUSID]->mii_bus.phy_map[AU1XXX_PHY0_ADDR]; +# else + printk (KERN_INFO DRV_NAME ":%s: using PHY-less setup\n", + dev->name); + return 0; +# endif /* defined(AU1XXX_PHY0_ADDR) */ + } else if (aup->mac_id == 1) { /* get PHY1 */ +# if defined(AU1XXX_PHY1_ADDR) + phydev = au_macs[AU1XXX_PHY1_BUSID]->mii_bus.phy_map[AU1XXX_PHY1_ADDR]; +# else + printk (KERN_INFO DRV_NAME ":%s: using PHY-less setup\n", + dev->name); + return 0; +# endif /* defined(AU1XXX_PHY1_ADDR) */ + } + +#else /* defined(AU1XXX_PHY_STATIC_CONFIG) */ + int phy_addr; + + /* find the first (lowest address) PHY on the current MAC's MII bus */ + for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++) + if (aup->mii_bus.phy_map[phy_addr]) { + phydev = aup->mii_bus.phy_map[phy_addr]; +# if !defined(AU1XXX_PHY_SEARCH_HIGHEST_ADDR) + break; /* break out with first one found */ +# endif } - } -found: - -#ifdef CONFIG_MIPS_BOSPORUS - /* This is a workaround for the Micrel/Kendin 5 port switch - The second MAC doesn't see a PHY connected... so we need to - trick it into thinking we have one. - - If this kernel is run on another Au1500 development board - the stub will be found as well as the actual PHY. However, - the last found PHY will be used... usually at Addr 31 (Db1500). - */ - if ( (!phy_found) ) - { - u16 phy_id0, phy_id1; - int i; - phy_id0 = 0x1234; - phy_id1 = 0x5678; - - /* search our mii table for the current mii */ - for (i = 0; mii_chip_table[i].phy_id1; i++) { - if (phy_id0 == mii_chip_table[i].phy_id0 && - phy_id1 == mii_chip_table[i].phy_id1) { - struct mii_phy * mii_phy; - - printk(KERN_INFO "%s: %s at phy address %d\n", - dev->name, mii_chip_table[i].name, - phy_addr); - mii_phy = kmalloc(sizeof(struct mii_phy), - GFP_KERNEL); - if (mii_phy) { - mii_phy->chip_info = mii_chip_table+i; - aup->phy_addr = phy_addr; - mii_phy->next = aup->mii; - aup->phy_ops = - mii_chip_table[i].phy_ops; - aup->mii = mii_phy; - aup->phy_ops->phy_init(dev,phy_addr); - } else { - printk(KERN_ERR "%s: out of memory\n", - dev->name); - return -1; - } - mii_phy->chip_info = mii_chip_table+i; - aup->phy_addr = phy_addr; - aup->phy_ops = mii_chip_table[i].phy_ops; - aup->phy_ops->phy_init(dev,phy_addr); - break; - } +# if defined(AU1XXX_PHY1_SEARCH_ON_MAC0) + /* try harder to find a PHY */ + if (!phydev && (aup->mac_id == 1)) { + /* no PHY found, maybe we have a dual PHY? */ + printk (KERN_INFO DRV_NAME ": no PHY found on MAC1, " + "let's see if it's attached to MAC0...\n"); + + BUG_ON(!au_macs[0]); + + /* find the first (lowest address) non-attached PHY on + * the MAC0 MII bus */ + for (phy_addr = 0; phy_addr < PHY_MAX_ADDR; phy_addr++) { + struct phy_device *const tmp_phydev = + au_macs[0]->mii_bus.phy_map[phy_addr]; + + if (!tmp_phydev) + continue; /* no PHY here... */ + + if (tmp_phydev->attached_dev) + continue; /* already claimed by MAC0 */ + + phydev = tmp_phydev; + break; /* found it */ } } - if (aup->mac_id == 0) { - /* the Bosporus phy responds to addresses 0-5 but - * 5 is the correct one. - */ - aup->phy_addr = 5; - } -#endif +# endif /* defined(AU1XXX_PHY1_SEARCH_OTHER_BUS) */ - if (aup->mii->chip_info == NULL) { - printk(KERN_ERR "%s: Au1x No known MII transceivers found!\n", - dev->name); +#endif /* defined(AU1XXX_PHY_STATIC_CONFIG) */ + if (!phydev) { + printk (KERN_ERR DRV_NAME ":%s: no PHY found\n", dev->name); return -1; } - printk(KERN_INFO "%s: Using %s as default\n", - dev->name, aup->mii->chip_info->name); + /* now we are supposed to have a proper phydev, to attach to... */ + BUG_ON(!phydev); + BUG_ON(phydev->attached_dev); + + phydev = phy_connect(dev, phydev->dev.bus_id, &au1000_adjust_link, 0); + + if (IS_ERR(phydev)) { + printk(KERN_ERR "%s: Could not attach to PHY\n", dev->name); + return PTR_ERR(phydev); + } + + /* mask with MAC supported features */ + phydev->supported &= (SUPPORTED_10baseT_Half + | SUPPORTED_10baseT_Full + | SUPPORTED_100baseT_Half + | SUPPORTED_100baseT_Full + | SUPPORTED_Autoneg + /* | SUPPORTED_Pause | SUPPORTED_Asym_Pause */ + | SUPPORTED_MII + | SUPPORTED_TP); + + phydev->advertising = phydev->supported; + + aup->old_link = 0; + aup->old_speed = 0; + aup->old_duplex = -1; + aup->phy_dev = phydev; + + printk(KERN_INFO "%s: attached PHY driver [%s] " + "(mii_bus:phy_addr=%s, irq=%d)\n", + dev->name, phydev->drv->name, phydev->dev.bus_id, phydev->irq); return 0; } @@ -1097,35 +439,38 @@ static void hard_stop(struct net_device *dev) au_sync_delay(10); } - -static void reset_mac(struct net_device *dev) +static void enable_mac(struct net_device *dev, int force_reset) { - int i; - u32 flags; + unsigned long flags; struct au1000_private *aup = (struct au1000_private *) dev->priv; - if (au1000_debug > 4) - printk(KERN_INFO "%s: reset mac, aup %x\n", - dev->name, (unsigned)aup); - spin_lock_irqsave(&aup->lock, flags); - if (aup->timer.function == &au1000_timer) {/* check if timer initted */ - del_timer(&aup->timer); - } - hard_stop(dev); - #ifdef CONFIG_BCM5222_DUAL_PHY - if (aup->mac_id != 0) { - #endif - /* If BCM5222, we can't leave MAC0 in reset because then - * we can't access the dual phy for ETH1 */ + if(force_reset || (!aup->mac_enabled)) { *aup->enable = MAC_EN_CLOCK_ENABLE; au_sync_delay(2); - *aup->enable = 0; + *aup->enable = (MAC_EN_RESET0 | MAC_EN_RESET1 | MAC_EN_RESET2 + | MAC_EN_CLOCK_ENABLE); au_sync_delay(2); - #ifdef CONFIG_BCM5222_DUAL_PHY + + aup->mac_enabled = 1; } - #endif + + spin_unlock_irqrestore(&aup->lock, flags); +} + +static void reset_mac_unlocked(struct net_device *dev) +{ + struct au1000_private *const aup = (struct au1000_private *) dev->priv; + int i; + + hard_stop(dev); + + *aup->enable = MAC_EN_CLOCK_ENABLE; + au_sync_delay(2); + *aup->enable = 0; + au_sync_delay(2); + aup->tx_full = 0; for (i = 0; i < NUM_RX_DMA; i++) { /* reset control bits */ @@ -1135,9 +480,26 @@ static void reset_mac(struct net_device *dev) /* reset control bits */ aup->tx_dma_ring[i]->buff_stat &= ~0xf; } - spin_unlock_irqrestore(&aup->lock, flags); + + aup->mac_enabled = 0; + } +static void reset_mac(struct net_device *dev) +{ + struct au1000_private *const aup = (struct au1000_private *) dev->priv; + unsigned long flags; + + if (au1000_debug > 4) + printk(KERN_INFO "%s: reset mac, aup %x\n", + dev->name, (unsigned)aup); + + spin_lock_irqsave(&aup->lock, flags); + + reset_mac_unlocked (dev); + + spin_unlock_irqrestore(&aup->lock, flags); +} /* * Setup the receive and transmit "rings". These pointers are the addresses @@ -1208,178 +570,31 @@ static int __init au1000_init_module(void) return 0; } -static int au1000_setup_aneg(struct net_device *dev, u32 advertise) -{ - struct au1000_private *aup = (struct au1000_private *)dev->priv; - u16 ctl, adv; - - /* Setup standard advertise */ - adv = mdio_read(dev, aup->phy_addr, MII_ADVERTISE); - adv &= ~(ADVERTISE_ALL | ADVERTISE_100BASE4); - if (advertise & ADVERTISED_10baseT_Half) - adv |= ADVERTISE_10HALF; - if (advertise & ADVERTISED_10baseT_Full) - adv |= ADVERTISE_10FULL; - if (advertise & ADVERTISED_100baseT_Half) - adv |= ADVERTISE_100HALF; - if (advertise & ADVERTISED_100baseT_Full) - adv |= ADVERTISE_100FULL; - mdio_write(dev, aup->phy_addr, MII_ADVERTISE, adv); - - /* Start/Restart aneg */ - ctl = mdio_read(dev, aup->phy_addr, MII_BMCR); - ctl |= (BMCR_ANENABLE | BMCR_ANRESTART); - mdio_write(dev, aup->phy_addr, MII_BMCR, ctl); - - return 0; -} +/* + * ethtool operations + */ -static int au1000_setup_forced(struct net_device *dev, int speed, int fd) +static int au1000_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) { struct au1000_private *aup = (struct au1000_private *)dev->priv; - u16 ctl; - - ctl = mdio_read(dev, aup->phy_addr, MII_BMCR); - ctl &= ~(BMCR_FULLDPLX | BMCR_SPEED100 | BMCR_ANENABLE); - - /* First reset the PHY */ - mdio_write(dev, aup->phy_addr, MII_BMCR, ctl | BMCR_RESET); - - /* Select speed & duplex */ - switch (speed) { - case SPEED_10: - break; - case SPEED_100: - ctl |= BMCR_SPEED100; - break; - case SPEED_1000: - default: - return -EINVAL; - } - if (fd == DUPLEX_FULL) - ctl |= BMCR_FULLDPLX; - mdio_write(dev, aup->phy_addr, MII_BMCR, ctl); - - return 0; -} - -static void -au1000_start_link(struct net_device *dev, struct ethtool_cmd *cmd) -{ - struct au1000_private *aup = (struct au1000_private *)dev->priv; - u32 advertise; - int autoneg; - int forced_speed; - int forced_duplex; - - /* Default advertise */ - advertise = GENMII_DEFAULT_ADVERTISE; - autoneg = aup->want_autoneg; - forced_speed = SPEED_100; - forced_duplex = DUPLEX_FULL; - - /* Setup link parameters */ - if (cmd) { - if (cmd->autoneg == AUTONEG_ENABLE) { - advertise = cmd->advertising; - autoneg = 1; - } else { - autoneg = 0; - - forced_speed = cmd->speed; - forced_duplex = cmd->duplex; - } - } + if (aup->phy_dev) + return phy_ethtool_gset(aup->phy_dev, cmd); - /* Configure PHY & start aneg */ - aup->want_autoneg = autoneg; - if (autoneg) - au1000_setup_aneg(dev, advertise); - else - au1000_setup_forced(dev, forced_speed, forced_duplex); - mod_timer(&aup->timer, jiffies + HZ); + return -EINVAL; } -static int au1000_get_settings(struct net_device *dev, struct ethtool_cmd *cmd) +static int au1000_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) { struct au1000_private *aup = (struct au1000_private *)dev->priv; - u16 link, speed; - - cmd->supported = GENMII_DEFAULT_FEATURES; - cmd->advertising = GENMII_DEFAULT_ADVERTISE; - cmd->port = PORT_MII; - cmd->transceiver = XCVR_EXTERNAL; - cmd->phy_address = aup->phy_addr; - spin_lock_irq(&aup->lock); - cmd->autoneg = aup->want_autoneg; - aup->phy_ops->phy_status(dev, aup->phy_addr, &link, &speed); - if ((speed == IF_PORT_100BASETX) || (speed == IF_PORT_100BASEFX)) - cmd->speed = SPEED_100; - else if (speed == IF_PORT_10BASET) - cmd->speed = SPEED_10; - if (link && (dev->if_port == IF_PORT_100BASEFX)) - cmd->duplex = DUPLEX_FULL; - else - cmd->duplex = DUPLEX_HALF; - spin_unlock_irq(&aup->lock); - return 0; -} -static int au1000_set_settings(struct net_device *dev, struct ethtool_cmd *cmd) -{ - struct au1000_private *aup = (struct au1000_private *)dev->priv; - unsigned long features = GENMII_DEFAULT_FEATURES; - - if (!capable(CAP_NET_ADMIN)) - return -EPERM; - - if (cmd->autoneg != AUTONEG_ENABLE && cmd->autoneg != AUTONEG_DISABLE) - return -EINVAL; - if (cmd->autoneg == AUTONEG_ENABLE && cmd->advertising == 0) - return -EINVAL; - if (cmd->duplex != DUPLEX_HALF && cmd->duplex != DUPLEX_FULL) - return -EINVAL; - if (cmd->autoneg == AUTONEG_DISABLE) - switch (cmd->speed) { - case SPEED_10: - if (cmd->duplex == DUPLEX_HALF && - (features & SUPPORTED_10baseT_Half) == 0) - return -EINVAL; - if (cmd->duplex == DUPLEX_FULL && - (features & SUPPORTED_10baseT_Full) == 0) - return -EINVAL; - break; - case SPEED_100: - if (cmd->duplex == DUPLEX_HALF && - (features & SUPPORTED_100baseT_Half) == 0) - return -EINVAL; - if (cmd->duplex == DUPLEX_FULL && - (features & SUPPORTED_100baseT_Full) == 0) - return -EINVAL; - break; - default: - return -EINVAL; - } - else if ((features & SUPPORTED_Autoneg) == 0) - return -EINVAL; - - spin_lock_irq(&aup->lock); - au1000_start_link(dev, cmd); - spin_unlock_irq(&aup->lock); - return 0; -} + if (!capable(CAP_NET_ADMIN)) + return -EPERM; -static int au1000_nway_reset(struct net_device *dev) -{ - struct au1000_private *aup = (struct au1000_private *)dev->priv; + if (aup->phy_dev) + return phy_ethtool_sset(aup->phy_dev, cmd); - if (!aup->want_autoneg) - return -EINVAL; - spin_lock_irq(&aup->lock); - au1000_start_link(dev, NULL); - spin_unlock_irq(&aup->lock); - return 0; + return -EINVAL; } static void @@ -1394,17 +609,11 @@ au1000_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info) info->regdump_len = 0; } -static u32 au1000_get_link(struct net_device *dev) -{ - return netif_carrier_ok(dev); -} - static struct ethtool_ops au1000_ethtool_ops = { .get_settings = au1000_get_settings, .set_settings = au1000_set_settings, .get_drvinfo = au1000_get_drvinfo, - .nway_reset = au1000_nway_reset, - .get_link = au1000_get_link + .get_link = ethtool_op_get_link, }; static struct net_device * au1000_probe(int port_num) @@ -1499,23 +708,31 @@ static struct net_device * au1000_probe(int port_num) memcpy(dev->dev_addr, au1000_mac_addr, sizeof(au1000_mac_addr)); dev->dev_addr[5] += port_num; - /* Bring the device out of reset, otherwise probing the MII will hang */ - *aup->enable = MAC_EN_CLOCK_ENABLE; - au_sync_delay(2); - *aup->enable = MAC_EN_RESET0 | MAC_EN_RESET1 | MAC_EN_RESET2 | - MAC_EN_CLOCK_ENABLE; - au_sync_delay(2); - - aup->mii = kmalloc(sizeof(struct mii_phy), GFP_KERNEL); - if (!aup->mii) { - printk(KERN_ERR "%s: out of memory\n", dev->name); - goto err_out; - } - aup->mii->next = NULL; - aup->mii->chip_info = NULL; - aup->mii->status = 0; - aup->mii->mii_control_reg = 0; - aup->mii->mii_data_reg = 0; + *aup->enable = 0; + aup->mac_enabled = 0; + + aup->mii_bus.priv = dev; + aup->mii_bus.read = mdiobus_read; + aup->mii_bus.write = mdiobus_write; + aup->mii_bus.reset = mdiobus_reset; + aup->mii_bus.name = "au1000_eth_mii"; + aup->mii_bus.id = aup->mac_id; + aup->mii_bus.irq = kmalloc(sizeof(int)*PHY_MAX_ADDR, GFP_KERNEL); + for(i = 0; i < PHY_MAX_ADDR; ++i) + aup->mii_bus.irq[i] = PHY_POLL; + + /* if known, set corresponding PHY IRQs */ +#if defined(AU1XXX_PHY_STATIC_CONFIG) +# if defined(AU1XXX_PHY0_IRQ) + if (AU1XXX_PHY0_BUSID == aup->mii_bus.id) + aup->mii_bus.irq[AU1XXX_PHY0_ADDR] = AU1XXX_PHY0_IRQ; +# endif +# if defined(AU1XXX_PHY1_IRQ) + if (AU1XXX_PHY1_BUSID == aup->mii_bus.id) + aup->mii_bus.irq[AU1XXX_PHY1_ADDR] = AU1XXX_PHY1_IRQ; +# endif +#endif + mdiobus_register(&aup->mii_bus); if (mii_probe(dev) != 0) { goto err_out; @@ -1561,7 +778,6 @@ static struct net_device * au1000_probe(int port_num) dev->set_multicast_list = &set_rx_mode; dev->do_ioctl = &au1000_ioctl; SET_ETHTOOL_OPS(dev, &au1000_ethtool_ops); - dev->set_config = &au1000_set_config; dev->tx_timeout = au1000_tx_timeout; dev->watchdog_timeo = ETH_TX_TIMEOUT; @@ -1577,7 +793,7 @@ err_out: /* here we should have a valid dev plus aup-> register addresses * so we can reset the mac properly.*/ reset_mac(dev); - kfree(aup->mii); + for (i = 0; i < NUM_RX_DMA; i++) { if (aup->rx_db_inuse[i]) ReleaseDB(aup, aup->rx_db_inuse[i]); @@ -1610,19 +826,14 @@ static int au1000_init(struct net_device *dev) u32 flags; int i; u32 control; - u16 link, speed; if (au1000_debug > 4) printk("%s: au1000_init\n", dev->name); - spin_lock_irqsave(&aup->lock, flags); - /* bring the device out of reset */ - *aup->enable = MAC_EN_CLOCK_ENABLE; - au_sync_delay(2); - *aup->enable = MAC_EN_RESET0 | MAC_EN_RESET1 | - MAC_EN_RESET2 | MAC_EN_CLOCK_ENABLE; - au_sync_delay(20); + enable_mac(dev, 1); + + spin_lock_irqsave(&aup->lock, flags); aup->mac->control = 0; aup->tx_head = (aup->tx_dma_ring[0]->buff_stat & 0xC) >> 2; @@ -1638,12 +849,16 @@ static int au1000_init(struct net_device *dev) } au_sync(); - aup->phy_ops->phy_status(dev, aup->phy_addr, &link, &speed); - control = MAC_DISABLE_RX_OWN | MAC_RX_ENABLE | MAC_TX_ENABLE; + control = MAC_RX_ENABLE | MAC_TX_ENABLE; #ifndef CONFIG_CPU_LITTLE_ENDIAN control |= MAC_BIG_ENDIAN; #endif - if (link && (dev->if_port == IF_PORT_100BASEFX)) { + if (aup->phy_dev) { + if (aup->phy_dev->link && (DUPLEX_FULL == aup->phy_dev->duplex)) + control |= MAC_FULL_DUPLEX; + else + control |= MAC_DISABLE_RX_OWN; + } else { /* PHY-less op, assume full-duplex */ control |= MAC_FULL_DUPLEX; } @@ -1655,57 +870,84 @@ static int au1000_init(struct net_device *dev) return 0; } -static void au1000_timer(unsigned long data) +static void +au1000_adjust_link(struct net_device *dev) { - struct net_device *dev = (struct net_device *)data; struct au1000_private *aup = (struct au1000_private *) dev->priv; - unsigned char if_port; - u16 link, speed; + struct phy_device *phydev = aup->phy_dev; + unsigned long flags; - if (!dev) { - /* fatal error, don't restart the timer */ - printk(KERN_ERR "au1000_timer error: NULL dev\n"); - return; - } + int status_change = 0; - if_port = dev->if_port; - if (aup->phy_ops->phy_status(dev, aup->phy_addr, &link, &speed) == 0) { - if (link) { - if (!netif_carrier_ok(dev)) { - netif_carrier_on(dev); - printk(KERN_INFO "%s: link up\n", dev->name); - } - } - else { - if (netif_carrier_ok(dev)) { - netif_carrier_off(dev); - dev->if_port = 0; - printk(KERN_INFO "%s: link down\n", dev->name); - } + BUG_ON(!aup->phy_dev); + + spin_lock_irqsave(&aup->lock, flags); + + if (phydev->link && (aup->old_speed != phydev->speed)) { + // speed changed + + switch(phydev->speed) { + case SPEED_10: + case SPEED_100: + break; + default: + printk(KERN_WARNING + "%s: Speed (%d) is not 10/100 ???\n", + dev->name, phydev->speed); + break; } + + aup->old_speed = phydev->speed; + + status_change = 1; } - if (link && (dev->if_port != if_port) && - (dev->if_port != IF_PORT_UNKNOWN)) { + if (phydev->link && (aup->old_duplex != phydev->duplex)) { + // duplex mode changed + + /* switching duplex mode requires to disable rx and tx! */ hard_stop(dev); - if (dev->if_port == IF_PORT_100BASEFX) { - printk(KERN_INFO "%s: going to full duplex\n", - dev->name); - aup->mac->control |= MAC_FULL_DUPLEX; - au_sync_delay(1); - } - else { - aup->mac->control &= ~MAC_FULL_DUPLEX; - au_sync_delay(1); - } + + if (DUPLEX_FULL == phydev->duplex) + aup->mac->control = ((aup->mac->control + | MAC_FULL_DUPLEX) + & ~MAC_DISABLE_RX_OWN); + else + aup->mac->control = ((aup->mac->control + & ~MAC_FULL_DUPLEX) + | MAC_DISABLE_RX_OWN); + au_sync_delay(1); + enable_rx_tx(dev); + aup->old_duplex = phydev->duplex; + + status_change = 1; + } + + if(phydev->link != aup->old_link) { + // link state changed + + if (phydev->link) // link went up + netif_schedule(dev); + else { // link went down + aup->old_speed = 0; + aup->old_duplex = -1; + } + + aup->old_link = phydev->link; + status_change = 1; } - aup->timer.expires = RUN_AT((1*HZ)); - aup->timer.data = (unsigned long)dev; - aup->timer.function = &au1000_timer; /* timer handler */ - add_timer(&aup->timer); + spin_unlock_irqrestore(&aup->lock, flags); + if (status_change) { + if (phydev->link) + printk(KERN_INFO "%s: link up (%d/%s)\n", + dev->name, phydev->speed, + DUPLEX_FULL == phydev->duplex ? "Full" : "Half"); + else + printk(KERN_INFO "%s: link down\n", dev->name); + } } static int au1000_open(struct net_device *dev) @@ -1716,25 +958,26 @@ static int au1000_open(struct net_device *dev) if (au1000_debug > 4) printk("%s: open: dev=%p\n", dev->name, dev); + if ((retval = request_irq(dev->irq, &au1000_interrupt, 0, + dev->name, dev))) { + printk(KERN_ERR "%s: unable to get IRQ %d\n", + dev->name, dev->irq); + return retval; + } + if ((retval = au1000_init(dev))) { printk(KERN_ERR "%s: error in au1000_init\n", dev->name); free_irq(dev->irq, dev); return retval; } - netif_start_queue(dev); - if ((retval = request_irq(dev->irq, &au1000_interrupt, 0, - dev->name, dev))) { - printk(KERN_ERR "%s: unable to get IRQ %d\n", - dev->name, dev->irq); - return retval; + if (aup->phy_dev) { + /* cause the PHY state machine to schedule a link state check */ + aup->phy_dev->state = PHY_CHANGELINK; + phy_start(aup->phy_dev); } - init_timer(&aup->timer); /* used in ioctl() */ - aup->timer.expires = RUN_AT((3*HZ)); - aup->timer.data = (unsigned long)dev; - aup->timer.function = &au1000_timer; /* timer handler */ - add_timer(&aup->timer); + netif_start_queue(dev); if (au1000_debug > 4) printk("%s: open: Initialization done.\n", dev->name); @@ -1744,16 +987,19 @@ static int au1000_open(struct net_device *dev) static int au1000_close(struct net_device *dev) { - u32 flags; - struct au1000_private *aup = (struct au1000_private *) dev->priv; + unsigned long flags; + struct au1000_private *const aup = (struct au1000_private *) dev->priv; if (au1000_debug > 4) printk("%s: close: dev=%p\n", dev->name, dev); - reset_mac(dev); + if (aup->phy_dev) + phy_stop(aup->phy_dev); spin_lock_irqsave(&aup->lock, flags); - + + reset_mac_unlocked (dev); + /* stop the device */ netif_stop_queue(dev); @@ -1775,7 +1021,6 @@ static void __exit au1000_cleanup_module(void) if (dev) { aup = (struct au1000_private *) dev->priv; unregister_netdev(dev); - kfree(aup->mii); for (j = 0; j < NUM_RX_DMA; j++) if (aup->rx_db_inuse[j]) ReleaseDB(aup, aup->rx_db_inuse[j]); @@ -1798,7 +1043,7 @@ static void update_tx_stats(struct net_device *dev, u32 status) struct net_device_stats *ps = &aup->stats; if (status & TX_FRAME_ABORTED) { - if (dev->if_port == IF_PORT_100BASEFX) { + if (!aup->phy_dev || (DUPLEX_FULL == aup->phy_dev->duplex)) { if (status & (TX_JAB_TIMEOUT | TX_UNDERRUN)) { /* any other tx errors are only valid * in half duplex mode */ @@ -2072,126 +1317,15 @@ static void set_rx_mode(struct net_device *dev) } } - static int au1000_ioctl(struct net_device *dev, struct ifreq *rq, int cmd) { struct au1000_private *aup = (struct au1000_private *)dev->priv; - u16 *data = (u16 *)&rq->ifr_ifru; - - switch(cmd) { - case SIOCDEVPRIVATE: /* Get the address of the PHY in use. */ - case SIOCGMIIPHY: - if (!netif_running(dev)) return -EINVAL; - data[0] = aup->phy_addr; - case SIOCDEVPRIVATE+1: /* Read the specified MII register. */ - case SIOCGMIIREG: - data[3] = mdio_read(dev, data[0], data[1]); - return 0; - case SIOCDEVPRIVATE+2: /* Write the specified MII register */ - case SIOCSMIIREG: - if (!capable(CAP_NET_ADMIN)) - return -EPERM; - mdio_write(dev, data[0], data[1],data[2]); - return 0; - default: - return -EOPNOTSUPP; - } - -} - - -static int au1000_set_config(struct net_device *dev, struct ifmap *map) -{ - struct au1000_private *aup = (struct au1000_private *) dev->priv; - u16 control; - if (au1000_debug > 4) { - printk("%s: set_config called: dev->if_port %d map->port %x\n", - dev->name, dev->if_port, map->port); - } + if (!netif_running(dev)) return -EINVAL; - switch(map->port){ - case IF_PORT_UNKNOWN: /* use auto here */ - printk(KERN_INFO "%s: config phy for aneg\n", - dev->name); - dev->if_port = map->port; - /* Link Down: the timer will bring it up */ - netif_carrier_off(dev); - - /* read current control */ - control = mdio_read(dev, aup->phy_addr, MII_CONTROL); - control &= ~(MII_CNTL_FDX | MII_CNTL_F100); - - /* enable auto negotiation and reset the negotiation */ - mdio_write(dev, aup->phy_addr, MII_CONTROL, - control | MII_CNTL_AUTO | - MII_CNTL_RST_AUTO); + if (!aup->phy_dev) return -EINVAL; // PHY not controllable - break; - - case IF_PORT_10BASET: /* 10BaseT */ - printk(KERN_INFO "%s: config phy for 10BaseT\n", - dev->name); - dev->if_port = map->port; - - /* Link Down: the timer will bring it up */ - netif_carrier_off(dev); - - /* set Speed to 10Mbps, Half Duplex */ - control = mdio_read(dev, aup->phy_addr, MII_CONTROL); - control &= ~(MII_CNTL_F100 | MII_CNTL_AUTO | - MII_CNTL_FDX); - - /* disable auto negotiation and force 10M/HD mode*/ - mdio_write(dev, aup->phy_addr, MII_CONTROL, control); - break; - - case IF_PORT_100BASET: /* 100BaseT */ - case IF_PORT_100BASETX: /* 100BaseTx */ - printk(KERN_INFO "%s: config phy for 100BaseTX\n", - dev->name); - dev->if_port = map->port; - - /* Link Down: the timer will bring it up */ - netif_carrier_off(dev); - - /* set Speed to 100Mbps, Half Duplex */ - /* disable auto negotiation and enable 100MBit Mode */ - control = mdio_read(dev, aup->phy_addr, MII_CONTROL); - control &= ~(MII_CNTL_AUTO | MII_CNTL_FDX); - control |= MII_CNTL_F100; - mdio_write(dev, aup->phy_addr, MII_CONTROL, control); - break; - - case IF_PORT_100BASEFX: /* 100BaseFx */ - printk(KERN_INFO "%s: config phy for 100BaseFX\n", - dev->name); - dev->if_port = map->port; - - /* Link Down: the timer will bring it up */ - netif_carrier_off(dev); - - /* set Speed to 100Mbps, Full Duplex */ - /* disable auto negotiation and enable 100MBit Mode */ - control = mdio_read(dev, aup->phy_addr, MII_CONTROL); - control &= ~MII_CNTL_AUTO; - control |= MII_CNTL_F100 | MII_CNTL_FDX; - mdio_write(dev, aup->phy_addr, MII_CONTROL, control); - break; - case IF_PORT_10BASE2: /* 10Base2 */ - case IF_PORT_AUI: /* AUI */ - /* These Modes are not supported (are they?)*/ - printk(KERN_ERR "%s: 10Base2/AUI not supported", - dev->name); - return -EOPNOTSUPP; - break; - - default: - printk(KERN_ERR "%s: Invalid media selected", - dev->name); - return -EINVAL; - } - return 0; + return phy_mii_ioctl(aup->phy_dev, if_mii(rq), cmd); } static struct net_device_stats *au1000_get_stats(struct net_device *dev) diff --git a/drivers/net/au1000_eth.h b/drivers/net/au1000_eth.h index 7f9326e39cc0..41c2f848d2c4 100644 --- a/drivers/net/au1000_eth.h +++ b/drivers/net/au1000_eth.h @@ -40,120 +40,6 @@ #define MULTICAST_FILTER_LIMIT 64 -/* FIXME - * The PHY defines should be in a separate file. - */ - -/* MII register offsets */ -#define MII_CONTROL 0x0000 -#define MII_STATUS 0x0001 -#define MII_PHY_ID0 0x0002 -#define MII_PHY_ID1 0x0003 -#define MII_ANADV 0x0004 -#define MII_ANLPAR 0x0005 -#define MII_AEXP 0x0006 -#define MII_ANEXT 0x0007 -#define MII_LSI_PHY_CONFIG 0x0011 -/* Status register */ -#define MII_LSI_PHY_STAT 0x0012 -#define MII_AMD_PHY_STAT MII_LSI_PHY_STAT -#define MII_INTEL_PHY_STAT 0x0011 - -#define MII_AUX_CNTRL 0x0018 -/* mii registers specific to AMD 79C901 */ -#define MII_STATUS_SUMMARY = 0x0018 - -/* MII Control register bit definitions. */ -#define MII_CNTL_FDX 0x0100 -#define MII_CNTL_RST_AUTO 0x0200 -#define MII_CNTL_ISOLATE 0x0400 -#define MII_CNTL_PWRDWN 0x0800 -#define MII_CNTL_AUTO 0x1000 -#define MII_CNTL_F100 0x2000 -#define MII_CNTL_LPBK 0x4000 -#define MII_CNTL_RESET 0x8000 - -/* MII Status register bit */ -#define MII_STAT_EXT 0x0001 -#define MII_STAT_JAB 0x0002 -#define MII_STAT_LINK 0x0004 -#define MII_STAT_CAN_AUTO 0x0008 -#define MII_STAT_FAULT 0x0010 -#define MII_STAT_AUTO_DONE 0x0020 -#define MII_STAT_CAN_T 0x0800 -#define MII_STAT_CAN_T_FDX 0x1000 -#define MII_STAT_CAN_TX 0x2000 -#define MII_STAT_CAN_TX_FDX 0x4000 -#define MII_STAT_CAN_T4 0x8000 - - -#define MII_ID1_OUI_LO 0xFC00 /* low bits of OUI mask */ -#define MII_ID1_MODEL 0x03F0 /* model number */ -#define MII_ID1_REV 0x000F /* model number */ - -/* MII NWAY Register Bits ... - valid for the ANAR (Auto-Negotiation Advertisement) and - ANLPAR (Auto-Negotiation Link Partner) registers */ -#define MII_NWAY_NODE_SEL 0x001f -#define MII_NWAY_CSMA_CD 0x0001 -#define MII_NWAY_T 0x0020 -#define MII_NWAY_T_FDX 0x0040 -#define MII_NWAY_TX 0x0080 -#define MII_NWAY_TX_FDX 0x0100 -#define MII_NWAY_T4 0x0200 -#define MII_NWAY_PAUSE 0x0400 -#define MII_NWAY_RF 0x2000 /* Remote Fault */ -#define MII_NWAY_ACK 0x4000 /* Remote Acknowledge */ -#define MII_NWAY_NP 0x8000 /* Next Page (Enable) */ - -/* mii stsout register bits */ -#define MII_STSOUT_LINK_FAIL 0x4000 -#define MII_STSOUT_SPD 0x0080 -#define MII_STSOUT_DPLX 0x0040 - -/* mii stsics register bits */ -#define MII_STSICS_SPD 0x8000 -#define MII_STSICS_DPLX 0x4000 -#define MII_STSICS_LINKSTS 0x0001 - -/* mii stssum register bits */ -#define MII_STSSUM_LINK 0x0008 -#define MII_STSSUM_DPLX 0x0004 -#define MII_STSSUM_AUTO 0x0002 -#define MII_STSSUM_SPD 0x0001 - -/* lsi phy status register */ -#define MII_LSI_PHY_STAT_FDX 0x0040 -#define MII_LSI_PHY_STAT_SPD 0x0080 - -/* amd phy status register */ -#define MII_AMD_PHY_STAT_FDX 0x0800 -#define MII_AMD_PHY_STAT_SPD 0x0400 - -/* intel phy status register */ -#define MII_INTEL_PHY_STAT_FDX 0x0200 -#define MII_INTEL_PHY_STAT_SPD 0x4000 - -/* Auxilliary Control/Status Register */ -#define MII_AUX_FDX 0x0001 -#define MII_AUX_100 0x0002 -#define MII_AUX_F100 0x0004 -#define MII_AUX_ANEG 0x0008 - -typedef struct mii_phy { - struct mii_phy * next; - struct mii_chip_info * chip_info; - u16 status; - u32 *mii_control_reg; - u32 *mii_data_reg; -} mii_phy_t; - -struct phy_ops { - int (*phy_init) (struct net_device *, int); - int (*phy_reset) (struct net_device *, int); - int (*phy_status) (struct net_device *, int, u16 *, u16 *); -}; - /* * Data Buffer Descriptor. Data buffers must be aligned on 32 byte * boundary for both, receive and transmit. @@ -200,7 +86,6 @@ typedef struct mac_reg { struct au1000_private { - db_dest_t *pDBfree; db_dest_t db[NUM_RX_BUFFS+NUM_TX_BUFFS]; volatile rx_dma_t *rx_dma_ring[NUM_RX_DMA]; @@ -213,8 +98,15 @@ struct au1000_private { u32 tx_full; int mac_id; - mii_phy_t *mii; - struct phy_ops *phy_ops; + + int mac_enabled; /* whether MAC is currently enabled and running (req. for mdio) */ + + int old_link; /* used by au1000_adjust_link */ + int old_speed; + int old_duplex; + + struct phy_device *phy_dev; + struct mii_bus mii_bus; /* These variables are just for quick access to certain regs addresses. */ volatile mac_reg_t *mac; /* mac registers */ @@ -223,14 +115,6 @@ struct au1000_private { u32 vaddr; /* virtual address of rx/tx buffers */ dma_addr_t dma_addr; /* dma address of rx/tx buffers */ - u8 *hash_table; - u32 hash_mode; - u32 intr_work_done; /* number of Rx and Tx pkts processed in the isr */ - int phy_addr; /* phy address */ - u32 options; /* User-settable misc. driver options. */ - u32 drv_flags; - int want_autoneg; struct net_device_stats stats; - struct timer_list timer; spinlock_t lock; /* Serialise access to device */ }; -- cgit v1.2.3