From 87f966d97b89774162df04d2106c6350c8fe4cb3 Mon Sep 17 00:00:00 2001 From: Markos Chandras Date: Thu, 19 Mar 2015 10:28:14 +0000 Subject: net: ethernet: pcnet32: Setup the SRAM and NOUFLO on Am79C97{3, 5} On a MIPS Malta board, tons of fifo underflow errors have been observed when using u-boot as bootloader instead of YAMON. The reason for that is that YAMON used to set the pcnet device to SRAM mode but u-boot does not. As a result, the default Tx threshold (64 bytes) is now too small to keep the fifo relatively used and it can result to Tx fifo underflow errors. As a result of which, it's best to setup the SRAM on supported controllers so we can always use the NOUFLO bit. Cc: Cc: Cc: Cc: Don Fry Signed-off-by: Markos Chandras Signed-off-by: David S. Miller --- drivers/net/ethernet/amd/pcnet32.c | 31 +++++++++++++++++++++++++++++-- 1 file changed, 29 insertions(+), 2 deletions(-) (limited to 'drivers/net/ethernet/amd') diff --git a/drivers/net/ethernet/amd/pcnet32.c b/drivers/net/ethernet/amd/pcnet32.c index 11d6e6561df1..15a8190a6f75 100644 --- a/drivers/net/ethernet/amd/pcnet32.c +++ b/drivers/net/ethernet/amd/pcnet32.c @@ -1543,7 +1543,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) { struct pcnet32_private *lp; int i, media; - int fdx, mii, fset, dxsuflo; + int fdx, mii, fset, dxsuflo, sram; int chip_version; char *chipname; struct net_device *dev; @@ -1580,7 +1580,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) } /* initialize variables */ - fdx = mii = fset = dxsuflo = 0; + fdx = mii = fset = dxsuflo = sram = 0; chip_version = (chip_version >> 12) & 0xffff; switch (chip_version) { @@ -1613,6 +1613,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) chipname = "PCnet/FAST III 79C973"; /* PCI */ fdx = 1; mii = 1; + sram = 1; break; case 0x2626: chipname = "PCnet/Home 79C978"; /* PCI */ @@ -1636,6 +1637,7 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) chipname = "PCnet/FAST III 79C975"; /* PCI */ fdx = 1; mii = 1; + sram = 1; break; case 0x2628: chipname = "PCnet/PRO 79C976"; @@ -1664,6 +1666,31 @@ pcnet32_probe1(unsigned long ioaddr, int shared, struct pci_dev *pdev) dxsuflo = 1; } + /* + * The Am79C973/Am79C975 controllers come with 12K of SRAM + * which we can use for the Tx/Rx buffers but most importantly, + * the use of SRAM allow us to use the BCR18:NOUFLO bit to avoid + * Tx fifo underflows. + */ + if (sram) { + /* + * The SRAM is being configured in two steps. First we + * set the SRAM size in the BCR25:SRAM_SIZE bits. According + * to the datasheet, each bit corresponds to a 512-byte + * page so we can have at most 24 pages. The SRAM_SIZE + * holds the value of the upper 8 bits of the 16-bit SRAM size. + * The low 8-bits start at 0x00 and end at 0xff. So the + * address range is from 0x0000 up to 0x17ff. Therefore, + * the SRAM_SIZE is set to 0x17. The next step is to set + * the BCR26:SRAM_BND midway through so the Tx and Rx + * buffers can share the SRAM equally. + */ + a->write_bcr(ioaddr, 25, 0x17); + a->write_bcr(ioaddr, 26, 0xc); + /* And finally enable the NOUFLO bit */ + a->write_bcr(ioaddr, 18, a->read_bcr(ioaddr, 18) | (1 << 11)); + } + dev = alloc_etherdev(sizeof(*lp)); if (!dev) { ret = -ENOMEM; -- cgit v1.2.3