From b40ddf575883ceca303906556bcd0cff5c284fef Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 28 Nov 2008 11:13:47 +0800 Subject: [ARM] pxa: move FICP register definitions into pxaficp_ir.c Signed-off-by: Eric Miao --- drivers/net/irda/pxaficp_ir.c | 42 ++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 42 insertions(+) (limited to 'drivers/net/irda/pxaficp_ir.c') diff --git a/drivers/net/irda/pxaficp_ir.c b/drivers/net/irda/pxaficp_ir.c index c5b02b66f756..06f448a37ca0 100644 --- a/drivers/net/irda/pxaficp_ir.c +++ b/drivers/net/irda/pxaficp_ir.c @@ -26,6 +26,48 @@ #include #include +#define FICP __REG(0x40800000) /* Start of FICP area */ +#define ICCR0 __REG(0x40800000) /* ICP Control Register 0 */ +#define ICCR1 __REG(0x40800004) /* ICP Control Register 1 */ +#define ICCR2 __REG(0x40800008) /* ICP Control Register 2 */ +#define ICDR __REG(0x4080000c) /* ICP Data Register */ +#define ICSR0 __REG(0x40800014) /* ICP Status Register 0 */ +#define ICSR1 __REG(0x40800018) /* ICP Status Register 1 */ + +#define ICCR0_AME (1 << 7) /* Address match enable */ +#define ICCR0_TIE (1 << 6) /* Transmit FIFO interrupt enable */ +#define ICCR0_RIE (1 << 5) /* Recieve FIFO interrupt enable */ +#define ICCR0_RXE (1 << 4) /* Receive enable */ +#define ICCR0_TXE (1 << 3) /* Transmit enable */ +#define ICCR0_TUS (1 << 2) /* Transmit FIFO underrun select */ +#define ICCR0_LBM (1 << 1) /* Loopback mode */ +#define ICCR0_ITR (1 << 0) /* IrDA transmission */ + +#define ICCR2_RXP (1 << 3) /* Receive Pin Polarity select */ +#define ICCR2_TXP (1 << 2) /* Transmit Pin Polarity select */ +#define ICCR2_TRIG (3 << 0) /* Receive FIFO Trigger threshold */ +#define ICCR2_TRIG_8 (0 << 0) /* >= 8 bytes */ +#define ICCR2_TRIG_16 (1 << 0) /* >= 16 bytes */ +#define ICCR2_TRIG_32 (2 << 0) /* >= 32 bytes */ + +#ifdef CONFIG_PXA27x +#define ICSR0_EOC (1 << 6) /* DMA End of Descriptor Chain */ +#endif +#define ICSR0_FRE (1 << 5) /* Framing error */ +#define ICSR0_RFS (1 << 4) /* Receive FIFO service request */ +#define ICSR0_TFS (1 << 3) /* Transnit FIFO service request */ +#define ICSR0_RAB (1 << 2) /* Receiver abort */ +#define ICSR0_TUR (1 << 1) /* Trunsmit FIFO underun */ +#define ICSR0_EIF (1 << 0) /* End/Error in FIFO */ + +#define ICSR1_ROR (1 << 6) /* Receiver FIFO underrun */ +#define ICSR1_CRE (1 << 5) /* CRC error */ +#define ICSR1_EOF (1 << 4) /* End of frame */ +#define ICSR1_TNF (1 << 3) /* Transmit FIFO not full */ +#define ICSR1_RNE (1 << 2) /* Receive FIFO not empty */ +#define ICSR1_TBY (1 << 1) /* Tramsmiter busy flag */ +#define ICSR1_RSY (1 << 0) /* Recevier synchronized flag */ + #define IrSR_RXPL_NEG_IS_ZERO (1<<4) #define IrSR_RXPL_POS_IS_ZERO 0x0 #define IrSR_TXPL_NEG_IS_ZERO (1<<3) -- cgit v1.2.3 From 02f652626a8f23e513877cb751c8ea533739c28f Mon Sep 17 00:00:00 2001 From: Eric Miao Date: Fri, 28 Nov 2008 14:08:53 +0800 Subject: [ARM] pxa: move UART register definitions into dedicated regs-uart.h Signed-off-by: Eric Miao --- arch/arm/mach-pxa/devices.c | 16 ++-- arch/arm/mach-pxa/include/mach/pxa-regs.h | 141 --------------------------- arch/arm/mach-pxa/include/mach/regs-uart.h | 143 ++++++++++++++++++++++++++++ arch/arm/mach-pxa/include/mach/uncompress.h | 2 +- drivers/net/irda/pxaficp_ir.c | 1 + drivers/serial/pxa.c | 1 + 6 files changed, 154 insertions(+), 150 deletions(-) create mode 100644 arch/arm/mach-pxa/include/mach/regs-uart.h (limited to 'drivers/net/irda/pxaficp_ir.c') diff --git a/arch/arm/mach-pxa/devices.c b/arch/arm/mach-pxa/devices.c index 541940b5d794..4db449258976 100644 --- a/arch/arm/mach-pxa/devices.c +++ b/arch/arm/mach-pxa/devices.c @@ -156,8 +156,8 @@ void __init set_pxa_fb_parent(struct device *parent_dev) static struct resource pxa_resource_ffuart[] = { { - .start = __PREG(FFUART), - .end = __PREG(FFUART) + 35, + .start = 0x40100000, + .end = 0x40100023, .flags = IORESOURCE_MEM, }, { .start = IRQ_FFUART, @@ -175,8 +175,8 @@ struct platform_device pxa_device_ffuart= { static struct resource pxa_resource_btuart[] = { { - .start = __PREG(BTUART), - .end = __PREG(BTUART) + 35, + .start = 0x40200000, + .end = 0x40200023, .flags = IORESOURCE_MEM, }, { .start = IRQ_BTUART, @@ -194,8 +194,8 @@ struct platform_device pxa_device_btuart = { static struct resource pxa_resource_stuart[] = { { - .start = __PREG(STUART), - .end = __PREG(STUART) + 35, + .start = 0x40700000, + .end = 0x40700023, .flags = IORESOURCE_MEM, }, { .start = IRQ_STUART, @@ -213,8 +213,8 @@ struct platform_device pxa_device_stuart = { static struct resource pxa_resource_hwuart[] = { { - .start = __PREG(HWUART), - .end = __PREG(HWUART) + 47, + .start = 0x41600000, + .end = 0x4160002F, .flags = IORESOURCE_MEM, }, { .start = IRQ_HWUART, diff --git a/arch/arm/mach-pxa/include/mach/pxa-regs.h b/arch/arm/mach-pxa/include/mach/pxa-regs.h index ab62f6c11e0e..cb9b46de97cc 100644 --- a/arch/arm/mach-pxa/include/mach/pxa-regs.h +++ b/arch/arm/mach-pxa/include/mach/pxa-regs.h @@ -123,147 +123,6 @@ #define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */ #define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */ - -/* - * UARTs - */ - -/* Full Function UART (FFUART) */ -#define FFUART FFRBR -#define FFRBR __REG(0x40100000) /* Receive Buffer Register (read only) */ -#define FFTHR __REG(0x40100000) /* Transmit Holding Register (write only) */ -#define FFIER __REG(0x40100004) /* Interrupt Enable Register (read/write) */ -#define FFIIR __REG(0x40100008) /* Interrupt ID Register (read only) */ -#define FFFCR __REG(0x40100008) /* FIFO Control Register (write only) */ -#define FFLCR __REG(0x4010000C) /* Line Control Register (read/write) */ -#define FFMCR __REG(0x40100010) /* Modem Control Register (read/write) */ -#define FFLSR __REG(0x40100014) /* Line Status Register (read only) */ -#define FFMSR __REG(0x40100018) /* Modem Status Register (read only) */ -#define FFSPR __REG(0x4010001C) /* Scratch Pad Register (read/write) */ -#define FFISR __REG(0x40100020) /* Infrared Selection Register (read/write) */ -#define FFDLL __REG(0x40100000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ -#define FFDLH __REG(0x40100004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ - -/* Bluetooth UART (BTUART) */ -#define BTUART BTRBR -#define BTRBR __REG(0x40200000) /* Receive Buffer Register (read only) */ -#define BTTHR __REG(0x40200000) /* Transmit Holding Register (write only) */ -#define BTIER __REG(0x40200004) /* Interrupt Enable Register (read/write) */ -#define BTIIR __REG(0x40200008) /* Interrupt ID Register (read only) */ -#define BTFCR __REG(0x40200008) /* FIFO Control Register (write only) */ -#define BTLCR __REG(0x4020000C) /* Line Control Register (read/write) */ -#define BTMCR __REG(0x40200010) /* Modem Control Register (read/write) */ -#define BTLSR __REG(0x40200014) /* Line Status Register (read only) */ -#define BTMSR __REG(0x40200018) /* Modem Status Register (read only) */ -#define BTSPR __REG(0x4020001C) /* Scratch Pad Register (read/write) */ -#define BTISR __REG(0x40200020) /* Infrared Selection Register (read/write) */ -#define BTDLL __REG(0x40200000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ -#define BTDLH __REG(0x40200004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ - -/* Standard UART (STUART) */ -#define STUART STRBR -#define STRBR __REG(0x40700000) /* Receive Buffer Register (read only) */ -#define STTHR __REG(0x40700000) /* Transmit Holding Register (write only) */ -#define STIER __REG(0x40700004) /* Interrupt Enable Register (read/write) */ -#define STIIR __REG(0x40700008) /* Interrupt ID Register (read only) */ -#define STFCR __REG(0x40700008) /* FIFO Control Register (write only) */ -#define STLCR __REG(0x4070000C) /* Line Control Register (read/write) */ -#define STMCR __REG(0x40700010) /* Modem Control Register (read/write) */ -#define STLSR __REG(0x40700014) /* Line Status Register (read only) */ -#define STMSR __REG(0x40700018) /* Reserved */ -#define STSPR __REG(0x4070001C) /* Scratch Pad Register (read/write) */ -#define STISR __REG(0x40700020) /* Infrared Selection Register (read/write) */ -#define STDLL __REG(0x40700000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ -#define STDLH __REG(0x40700004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ - -/* Hardware UART (HWUART) */ -#define HWUART HWRBR -#define HWRBR __REG(0x41600000) /* Receive Buffer Register (read only) */ -#define HWTHR __REG(0x41600000) /* Transmit Holding Register (write only) */ -#define HWIER __REG(0x41600004) /* Interrupt Enable Register (read/write) */ -#define HWIIR __REG(0x41600008) /* Interrupt ID Register (read only) */ -#define HWFCR __REG(0x41600008) /* FIFO Control Register (write only) */ -#define HWLCR __REG(0x4160000C) /* Line Control Register (read/write) */ -#define HWMCR __REG(0x41600010) /* Modem Control Register (read/write) */ -#define HWLSR __REG(0x41600014) /* Line Status Register (read only) */ -#define HWMSR __REG(0x41600018) /* Modem Status Register (read only) */ -#define HWSPR __REG(0x4160001C) /* Scratch Pad Register (read/write) */ -#define HWISR __REG(0x41600020) /* Infrared Selection Register (read/write) */ -#define HWFOR __REG(0x41600024) /* Receive FIFO Occupancy Register (read only) */ -#define HWABR __REG(0x41600028) /* Auto-Baud Control Register (read/write) */ -#define HWACR __REG(0x4160002C) /* Auto-Baud Count Register (read only) */ -#define HWDLL __REG(0x41600000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ -#define HWDLH __REG(0x41600004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ - -#define IER_DMAE (1 << 7) /* DMA Requests Enable */ -#define IER_UUE (1 << 6) /* UART Unit Enable */ -#define IER_NRZE (1 << 5) /* NRZ coding Enable */ -#define IER_RTIOE (1 << 4) /* Receiver Time Out Interrupt Enable */ -#define IER_MIE (1 << 3) /* Modem Interrupt Enable */ -#define IER_RLSE (1 << 2) /* Receiver Line Status Interrupt Enable */ -#define IER_TIE (1 << 1) /* Transmit Data request Interrupt Enable */ -#define IER_RAVIE (1 << 0) /* Receiver Data Available Interrupt Enable */ - -#define IIR_FIFOES1 (1 << 7) /* FIFO Mode Enable Status */ -#define IIR_FIFOES0 (1 << 6) /* FIFO Mode Enable Status */ -#define IIR_TOD (1 << 3) /* Time Out Detected */ -#define IIR_IID2 (1 << 2) /* Interrupt Source Encoded */ -#define IIR_IID1 (1 << 1) /* Interrupt Source Encoded */ -#define IIR_IP (1 << 0) /* Interrupt Pending (active low) */ - -#define FCR_ITL2 (1 << 7) /* Interrupt Trigger Level */ -#define FCR_ITL1 (1 << 6) /* Interrupt Trigger Level */ -#define FCR_RESETTF (1 << 2) /* Reset Transmitter FIFO */ -#define FCR_RESETRF (1 << 1) /* Reset Receiver FIFO */ -#define FCR_TRFIFOE (1 << 0) /* Transmit and Receive FIFO Enable */ -#define FCR_ITL_1 (0) -#define FCR_ITL_8 (FCR_ITL1) -#define FCR_ITL_16 (FCR_ITL2) -#define FCR_ITL_32 (FCR_ITL2|FCR_ITL1) - -#define LCR_DLAB (1 << 7) /* Divisor Latch Access Bit */ -#define LCR_SB (1 << 6) /* Set Break */ -#define LCR_STKYP (1 << 5) /* Sticky Parity */ -#define LCR_EPS (1 << 4) /* Even Parity Select */ -#define LCR_PEN (1 << 3) /* Parity Enable */ -#define LCR_STB (1 << 2) /* Stop Bit */ -#define LCR_WLS1 (1 << 1) /* Word Length Select */ -#define LCR_WLS0 (1 << 0) /* Word Length Select */ - -#define LSR_FIFOE (1 << 7) /* FIFO Error Status */ -#define LSR_TEMT (1 << 6) /* Transmitter Empty */ -#define LSR_TDRQ (1 << 5) /* Transmit Data Request */ -#define LSR_BI (1 << 4) /* Break Interrupt */ -#define LSR_FE (1 << 3) /* Framing Error */ -#define LSR_PE (1 << 2) /* Parity Error */ -#define LSR_OE (1 << 1) /* Overrun Error */ -#define LSR_DR (1 << 0) /* Data Ready */ - -#define MCR_LOOP (1 << 4) -#define MCR_OUT2 (1 << 3) /* force MSR_DCD in loopback mode */ -#define MCR_OUT1 (1 << 2) /* force MSR_RI in loopback mode */ -#define MCR_RTS (1 << 1) /* Request to Send */ -#define MCR_DTR (1 << 0) /* Data Terminal Ready */ - -#define MSR_DCD (1 << 7) /* Data Carrier Detect */ -#define MSR_RI (1 << 6) /* Ring Indicator */ -#define MSR_DSR (1 << 5) /* Data Set Ready */ -#define MSR_CTS (1 << 4) /* Clear To Send */ -#define MSR_DDCD (1 << 3) /* Delta Data Carrier Detect */ -#define MSR_TERI (1 << 2) /* Trailing Edge Ring Indicator */ -#define MSR_DDSR (1 << 1) /* Delta Data Set Ready */ -#define MSR_DCTS (1 << 0) /* Delta Clear To Send */ - -/* - * IrSR (Infrared Selection Register) - */ -#define STISR_RXPL (1 << 4) /* Receive Data Polarity */ -#define STISR_TXPL (1 << 3) /* Transmit Data Polarity */ -#define STISR_XMODE (1 << 2) /* Transmit Pulse Width Select */ -#define STISR_RCVEIR (1 << 1) /* Receiver SIR Enable */ -#define STISR_XMITIR (1 << 0) /* Transmitter SIR Enable */ - - /* * I2C registers - moved into drivers/i2c/busses/i2c-pxa.c */ diff --git a/arch/arm/mach-pxa/include/mach/regs-uart.h b/arch/arm/mach-pxa/include/mach/regs-uart.h new file mode 100644 index 000000000000..55aeb7fb72f6 --- /dev/null +++ b/arch/arm/mach-pxa/include/mach/regs-uart.h @@ -0,0 +1,143 @@ +#ifndef __ASM_ARCH_REGS_UART_H +#define __ASM_ARCH_REGS_UART_H + +/* + * UARTs + */ + +/* Full Function UART (FFUART) */ +#define FFUART FFRBR +#define FFRBR __REG(0x40100000) /* Receive Buffer Register (read only) */ +#define FFTHR __REG(0x40100000) /* Transmit Holding Register (write only) */ +#define FFIER __REG(0x40100004) /* Interrupt Enable Register (read/write) */ +#define FFIIR __REG(0x40100008) /* Interrupt ID Register (read only) */ +#define FFFCR __REG(0x40100008) /* FIFO Control Register (write only) */ +#define FFLCR __REG(0x4010000C) /* Line Control Register (read/write) */ +#define FFMCR __REG(0x40100010) /* Modem Control Register (read/write) */ +#define FFLSR __REG(0x40100014) /* Line Status Register (read only) */ +#define FFMSR __REG(0x40100018) /* Modem Status Register (read only) */ +#define FFSPR __REG(0x4010001C) /* Scratch Pad Register (read/write) */ +#define FFISR __REG(0x40100020) /* Infrared Selection Register (read/write) */ +#define FFDLL __REG(0x40100000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define FFDLH __REG(0x40100004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Bluetooth UART (BTUART) */ +#define BTUART BTRBR +#define BTRBR __REG(0x40200000) /* Receive Buffer Register (read only) */ +#define BTTHR __REG(0x40200000) /* Transmit Holding Register (write only) */ +#define BTIER __REG(0x40200004) /* Interrupt Enable Register (read/write) */ +#define BTIIR __REG(0x40200008) /* Interrupt ID Register (read only) */ +#define BTFCR __REG(0x40200008) /* FIFO Control Register (write only) */ +#define BTLCR __REG(0x4020000C) /* Line Control Register (read/write) */ +#define BTMCR __REG(0x40200010) /* Modem Control Register (read/write) */ +#define BTLSR __REG(0x40200014) /* Line Status Register (read only) */ +#define BTMSR __REG(0x40200018) /* Modem Status Register (read only) */ +#define BTSPR __REG(0x4020001C) /* Scratch Pad Register (read/write) */ +#define BTISR __REG(0x40200020) /* Infrared Selection Register (read/write) */ +#define BTDLL __REG(0x40200000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define BTDLH __REG(0x40200004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Standard UART (STUART) */ +#define STUART STRBR +#define STRBR __REG(0x40700000) /* Receive Buffer Register (read only) */ +#define STTHR __REG(0x40700000) /* Transmit Holding Register (write only) */ +#define STIER __REG(0x40700004) /* Interrupt Enable Register (read/write) */ +#define STIIR __REG(0x40700008) /* Interrupt ID Register (read only) */ +#define STFCR __REG(0x40700008) /* FIFO Control Register (write only) */ +#define STLCR __REG(0x4070000C) /* Line Control Register (read/write) */ +#define STMCR __REG(0x40700010) /* Modem Control Register (read/write) */ +#define STLSR __REG(0x40700014) /* Line Status Register (read only) */ +#define STMSR __REG(0x40700018) /* Reserved */ +#define STSPR __REG(0x4070001C) /* Scratch Pad Register (read/write) */ +#define STISR __REG(0x40700020) /* Infrared Selection Register (read/write) */ +#define STDLL __REG(0x40700000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define STDLH __REG(0x40700004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +/* Hardware UART (HWUART) */ +#define HWUART HWRBR +#define HWRBR __REG(0x41600000) /* Receive Buffer Register (read only) */ +#define HWTHR __REG(0x41600000) /* Transmit Holding Register (write only) */ +#define HWIER __REG(0x41600004) /* Interrupt Enable Register (read/write) */ +#define HWIIR __REG(0x41600008) /* Interrupt ID Register (read only) */ +#define HWFCR __REG(0x41600008) /* FIFO Control Register (write only) */ +#define HWLCR __REG(0x4160000C) /* Line Control Register (read/write) */ +#define HWMCR __REG(0x41600010) /* Modem Control Register (read/write) */ +#define HWLSR __REG(0x41600014) /* Line Status Register (read only) */ +#define HWMSR __REG(0x41600018) /* Modem Status Register (read only) */ +#define HWSPR __REG(0x4160001C) /* Scratch Pad Register (read/write) */ +#define HWISR __REG(0x41600020) /* Infrared Selection Register (read/write) */ +#define HWFOR __REG(0x41600024) /* Receive FIFO Occupancy Register (read only) */ +#define HWABR __REG(0x41600028) /* Auto-Baud Control Register (read/write) */ +#define HWACR __REG(0x4160002C) /* Auto-Baud Count Register (read only) */ +#define HWDLL __REG(0x41600000) /* Divisor Latch Low Register (DLAB = 1) (read/write) */ +#define HWDLH __REG(0x41600004) /* Divisor Latch High Register (DLAB = 1) (read/write) */ + +#define IER_DMAE (1 << 7) /* DMA Requests Enable */ +#define IER_UUE (1 << 6) /* UART Unit Enable */ +#define IER_NRZE (1 << 5) /* NRZ coding Enable */ +#define IER_RTIOE (1 << 4) /* Receiver Time Out Interrupt Enable */ +#define IER_MIE (1 << 3) /* Modem Interrupt Enable */ +#define IER_RLSE (1 << 2) /* Receiver Line Status Interrupt Enable */ +#define IER_TIE (1 << 1) /* Transmit Data request Interrupt Enable */ +#define IER_RAVIE (1 << 0) /* Receiver Data Available Interrupt Enable */ + +#define IIR_FIFOES1 (1 << 7) /* FIFO Mode Enable Status */ +#define IIR_FIFOES0 (1 << 6) /* FIFO Mode Enable Status */ +#define IIR_TOD (1 << 3) /* Time Out Detected */ +#define IIR_IID2 (1 << 2) /* Interrupt Source Encoded */ +#define IIR_IID1 (1 << 1) /* Interrupt Source Encoded */ +#define IIR_IP (1 << 0) /* Interrupt Pending (active low) */ + +#define FCR_ITL2 (1 << 7) /* Interrupt Trigger Level */ +#define FCR_ITL1 (1 << 6) /* Interrupt Trigger Level */ +#define FCR_RESETTF (1 << 2) /* Reset Transmitter FIFO */ +#define FCR_RESETRF (1 << 1) /* Reset Receiver FIFO */ +#define FCR_TRFIFOE (1 << 0) /* Transmit and Receive FIFO Enable */ +#define FCR_ITL_1 (0) +#define FCR_ITL_8 (FCR_ITL1) +#define FCR_ITL_16 (FCR_ITL2) +#define FCR_ITL_32 (FCR_ITL2|FCR_ITL1) + +#define LCR_DLAB (1 << 7) /* Divisor Latch Access Bit */ +#define LCR_SB (1 << 6) /* Set Break */ +#define LCR_STKYP (1 << 5) /* Sticky Parity */ +#define LCR_EPS (1 << 4) /* Even Parity Select */ +#define LCR_PEN (1 << 3) /* Parity Enable */ +#define LCR_STB (1 << 2) /* Stop Bit */ +#define LCR_WLS1 (1 << 1) /* Word Length Select */ +#define LCR_WLS0 (1 << 0) /* Word Length Select */ + +#define LSR_FIFOE (1 << 7) /* FIFO Error Status */ +#define LSR_TEMT (1 << 6) /* Transmitter Empty */ +#define LSR_TDRQ (1 << 5) /* Transmit Data Request */ +#define LSR_BI (1 << 4) /* Break Interrupt */ +#define LSR_FE (1 << 3) /* Framing Error */ +#define LSR_PE (1 << 2) /* Parity Error */ +#define LSR_OE (1 << 1) /* Overrun Error */ +#define LSR_DR (1 << 0) /* Data Ready */ + +#define MCR_LOOP (1 << 4) +#define MCR_OUT2 (1 << 3) /* force MSR_DCD in loopback mode */ +#define MCR_OUT1 (1 << 2) /* force MSR_RI in loopback mode */ +#define MCR_RTS (1 << 1) /* Request to Send */ +#define MCR_DTR (1 << 0) /* Data Terminal Ready */ + +#define MSR_DCD (1 << 7) /* Data Carrier Detect */ +#define MSR_RI (1 << 6) /* Ring Indicator */ +#define MSR_DSR (1 << 5) /* Data Set Ready */ +#define MSR_CTS (1 << 4) /* Clear To Send */ +#define MSR_DDCD (1 << 3) /* Delta Data Carrier Detect */ +#define MSR_TERI (1 << 2) /* Trailing Edge Ring Indicator */ +#define MSR_DDSR (1 << 1) /* Delta Data Set Ready */ +#define MSR_DCTS (1 << 0) /* Delta Clear To Send */ + +/* + * IrSR (Infrared Selection Register) + */ +#define STISR_RXPL (1 << 4) /* Receive Data Polarity */ +#define STISR_TXPL (1 << 3) /* Transmit Data Polarity */ +#define STISR_XMODE (1 << 2) /* Transmit Pulse Width Select */ +#define STISR_RCVEIR (1 << 1) /* Receiver SIR Enable */ +#define STISR_XMITIR (1 << 0) /* Transmitter SIR Enable */ + +#endif /* __ASM_ARCH_REGS_UART_H */ diff --git a/arch/arm/mach-pxa/include/mach/uncompress.h b/arch/arm/mach-pxa/include/mach/uncompress.h index 21e3e890af98..a9a4f302b6ef 100644 --- a/arch/arm/mach-pxa/include/mach/uncompress.h +++ b/arch/arm/mach-pxa/include/mach/uncompress.h @@ -10,7 +10,7 @@ */ #include -#include +#include #include #define __REG(x) ((volatile unsigned long *)x) diff --git a/drivers/net/irda/pxaficp_ir.c b/drivers/net/irda/pxaficp_ir.c index 06f448a37ca0..ba445133f3eb 100644 --- a/drivers/net/irda/pxaficp_ir.c +++ b/drivers/net/irda/pxaficp_ir.c @@ -25,6 +25,7 @@ #include #include #include +#include #define FICP __REG(0x40800000) /* Start of FICP area */ #define ICCR0 __REG(0x40800000) /* ICP Control Register 0 */ diff --git a/drivers/serial/pxa.c b/drivers/serial/pxa.c index abc00be55433..a793d1fa1cde 100644 --- a/drivers/serial/pxa.c +++ b/drivers/serial/pxa.c @@ -48,6 +48,7 @@ #include #include #include +#include struct uart_pxa_port { -- cgit v1.2.3