From 20c7722a7aa33e5b9de0c0d62b7ec0a2455e6725 Mon Sep 17 00:00:00 2001 From: Niklas Söderlund Date: Sat, 5 Oct 2024 13:24:12 +0200 Subject: net: phy: marvell-88q2xxx: Enable auto negotiation for mv88q2110 MIME-Version: 1.0 Content-Type: text/plain; charset=UTF-8 Content-Transfer-Encoding: 8bit The initial marvell-88q2xxx driver only supported the Marvell 88Q2110 PHY without auto negotiation support. The reason documented states that the provided initialization sequence did not to work. Now a method to enable auto negotiation have been found by comparing the initialization of other supported devices and an out-of-tree PHY driver. Perform the minimal needed initialization of the PHY to get auto negotiation working and remove the limitation that disables the auto negotiation feature for the mv88q2110 device. With this change a 1000Mbps full duplex link is able to be negotiated between two mv88q2110 and the link works perfectly. The other side also reflects the manually configure settings of the master device. # ethtool eth0 Settings for eth0: Supported ports: [ ] Supported link modes: 100baseT1/Full 1000baseT1/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 100baseT1/Full 1000baseT1/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 100baseT1/Full 1000baseT1/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Auto-negotiation: on master-slave cfg: preferred master master-slave status: slave Port: Twisted Pair PHYAD: 0 Transceiver: external MDI-X: Unknown Link detected: yes SQI: 15/15 Before this change I was not able to manually configure 1000Mbps link, only a 100Mpps link so this change providers an improvement in performance for this device. [ 5] local 10.1.0.2 port 5201 connected to 10.1.0.1 port 38346 [ ID] Interval Transfer Bitrate Retr Cwnd [ 5] 0.00-1.00 sec 96.8 MBytes 812 Mbits/sec 0 469 KBytes [ 5] 1.00-2.00 sec 94.3 MBytes 791 Mbits/sec 0 469 KBytes [ 5] 2.00-3.00 sec 96.1 MBytes 806 Mbits/sec 0 469 KBytes [ 5] 3.00-4.00 sec 98.3 MBytes 825 Mbits/sec 0 469 KBytes [ 5] 4.00-5.00 sec 98.4 MBytes 825 Mbits/sec 0 469 KBytes [ 5] 5.00-6.00 sec 98.4 MBytes 826 Mbits/sec 0 469 KBytes [ 5] 6.00-7.00 sec 98.9 MBytes 830 Mbits/sec 0 469 KBytes [ 5] 7.00-8.00 sec 91.7 MBytes 769 Mbits/sec 0 469 KBytes [ 5] 8.00-9.00 sec 99.4 MBytes 834 Mbits/sec 0 747 KBytes [ 5] 9.00-10.00 sec 101 MBytes 851 Mbits/sec 0 747 KBytes Signed-off-by: Niklas Söderlund Tested-by: Stefan Eichenberger Reviewed-by: Andrew Lunn Link: https://patch.msgid.link/20241005112412.544360-4-niklas.soderlund+renesas@ragnatech.se Signed-off-by: Jakub Kicinski --- drivers/net/phy/marvell-88q2xxx.c | 46 ++++++++++++++++++++++++++++++--------- 1 file changed, 36 insertions(+), 10 deletions(-) (limited to 'drivers/net/phy') diff --git a/drivers/net/phy/marvell-88q2xxx.c b/drivers/net/phy/marvell-88q2xxx.c index 31f8c976e387..5107f58338af 100644 --- a/drivers/net/phy/marvell-88q2xxx.c +++ b/drivers/net/phy/marvell-88q2xxx.c @@ -101,6 +101,22 @@ struct mmd_val { u16 val; }; +static const struct mmd_val mv88q2110_init_seq0[] = { + { MDIO_MMD_PCS, 0xffe4, 0x07b5 }, + { MDIO_MMD_PCS, 0xffe4, 0x06b6 }, +}; + +static const struct mmd_val mv88q2110_init_seq1[] = { + { MDIO_MMD_PCS, 0xffde, 0x402f }, + { MDIO_MMD_PCS, 0xfe34, 0x4040 }, + { MDIO_MMD_PCS, 0xfe2a, 0x3c1d }, + { MDIO_MMD_PCS, 0xfe34, 0x0040 }, + { MDIO_MMD_AN, 0x8032, 0x0064 }, + { MDIO_MMD_AN, 0x8031, 0x0a01 }, + { MDIO_MMD_AN, 0x8031, 0x0c01 }, + { MDIO_MMD_PCS, 0xffdb, 0x0010 }, +}; + static const struct mmd_val mv88q222x_revb0_init_seq0[] = { { MDIO_MMD_PCS, 0x8033, 0x6801 }, { MDIO_MMD_AN, MDIO_AN_T1_CTRL, 0x0 }, @@ -424,15 +440,6 @@ static int mv88q2xxx_get_features(struct phy_device *phydev) if (ret) return ret; - /* The PHY signalizes it supports autonegotiation. Unfortunately, so - * far it was not possible to get a link even when following the init - * sequence provided by Marvell. Disable it for now until a proper - * workaround is found or a new PHY revision is released. - */ - if (phydev->drv->phy_id == MARVELL_PHY_ID_88Q2110) - linkmode_clear_bit(ETHTOOL_LINK_MODE_Autoneg_BIT, - phydev->supported); - return 0; } @@ -739,6 +746,25 @@ static int mv88q2xxx_probe(struct phy_device *phydev) return mv88q2xxx_hwmon_probe(phydev); } +static int mv88q2110_config_init(struct phy_device *phydev) +{ + int ret; + + ret = mv88q2xxx_write_mmd_vals(phydev, mv88q2110_init_seq0, + ARRAY_SIZE(mv88q2110_init_seq0)); + if (ret < 0) + return ret; + + usleep_range(5000, 10000); + + ret = mv88q2xxx_write_mmd_vals(phydev, mv88q2110_init_seq1, + ARRAY_SIZE(mv88q2110_init_seq1)); + if (ret < 0) + return ret; + + return mv88q2xxx_config_init(phydev); +} + static int mv88q222x_revb0_config_init(struct phy_device *phydev) { int ret; @@ -880,7 +906,7 @@ static struct phy_driver mv88q2xxx_driver[] = { .name = "mv88q2110", .get_features = mv88q2xxx_get_features, .config_aneg = mv88q2xxx_config_aneg, - .config_init = mv88q2xxx_config_init, + .config_init = mv88q2110_config_init, .read_status = mv88q2xxx_read_status, .soft_reset = mv88q2xxx_soft_reset, .set_loopback = genphy_c45_loopback, -- cgit v1.2.3