From 4808a1c0261176f9c7e28e7f108d41a381a7d0fc Mon Sep 17 00:00:00 2001 From: Olav Kongas Date: Sat, 9 Apr 2005 22:57:39 +0300 Subject: [PATCH] USB: Add isp116x-hcd USB host controller driver This patch provides an "isp116x-hcd" driver for Philips' ISP1160/ISP1161 USB host controllers. The driver: - is relatively small, meant for use on embedded platforms. - runs usbtests 1-14 without problems for days. - has been in use by 6-7 different people on ARM and PPC platforms, running a range of devices including USB hubs. - supports suspend/resume of both the platform device and the root hub; supports remote wakeup of the root hub (but NOT the platform device) by USB devices. - does NOT support ISO transfers (nobody has asked for them). - is PIO-only. Signed-off-by: Olav Kongas Signed-off-by: Greg Kroah-Hartman --- include/linux/usb_isp116x.h | 47 +++++++++++++++++++++++++++++++++++++++++++++ 1 file changed, 47 insertions(+) create mode 100644 include/linux/usb_isp116x.h (limited to 'include') diff --git a/include/linux/usb_isp116x.h b/include/linux/usb_isp116x.h new file mode 100644 index 000000000000..5f5a9d9bd6c2 --- /dev/null +++ b/include/linux/usb_isp116x.h @@ -0,0 +1,47 @@ + +/* + * Board initialization code should put one of these into dev->platform_data + * and place the isp116x onto platform_bus. + */ + +struct isp116x_platform_data { + /* Enable internal resistors on downstream ports */ + unsigned sel15Kres:1; + /* Chip's internal clock won't be stopped in suspended state. + Setting/unsetting this bit takes effect only if + 'remote_wakeup_enable' below is not set. */ + unsigned clknotstop:1; + /* On-chip overcurrent protection */ + unsigned oc_enable:1; + /* INT output polarity */ + unsigned int_act_high:1; + /* INT edge or level triggered */ + unsigned int_edge_triggered:1; + /* WAKEUP pin connected - NOT SUPPORTED */ + /* unsigned remote_wakeup_connected:1; */ + /* Wakeup by devices on usb bus enabled */ + unsigned remote_wakeup_enable:1; + /* Switch or not to switch (keep always powered) */ + unsigned no_power_switching:1; + /* Ganged port power switching (0) or individual port + power switching (1) */ + unsigned power_switching_mode:1; + /* Given port_power, msec/2 after power on till power good */ + u8 potpg; + /* Hardware reset set/clear. If implemented, this function must: + if set == 0, deassert chip's HW reset pin + otherwise, assert chip's HW reset pin */ + void (*reset) (struct device * dev, int set); + /* Hardware clock start/stop. If implemented, this function must: + if start == 0, stop the external clock + otherwise, start the external clock + */ + void (*clock) (struct device * dev, int start); + /* Inter-io delay (ns). The chip is picky about access timings; it + expects at least: + 150ns delay between consecutive accesses to DATA_REG, + 300ns delay between access to ADDR_REG and DATA_REG + OE, WE MUST NOT be changed during these intervals + */ + void (*delay) (struct device * dev, int delay); +}; -- cgit v1.2.3 From 65111084c63d7674dc37833e8eb59cfdaa4d0bda Mon Sep 17 00:00:00 2001 From: David Brownell Date: Thu, 28 Apr 2005 13:52:31 -0700 Subject: [PATCH] USB: more omap_udc updates (dma and omap1710) More omap_udc updates: * OMAP 1710 updates - new UDC bit for clearing endpoint toggle, affecting CLEAR_HALT - new OTG bits affecting wakeup * Fix the bug Vladimir noted, that IN-DMA transfer code path kicks in for under 1024 bytes (not "up to 1024 bytes") * Handle transceiver setup more intelligently - use transceiver whenever one's available; this can be handy for GPIO based, loopback, or transceiverless configs - cleanup correctly after the "unrecognized HMC" case * DMA performance tweaks - allow burst/pack for memory access - use 16 bit DMA access most of the time on TIPB * Add workarounds for some DMA errata (not observed "in the wild"): - DMA CSAC/CDAC reads returning zero - RX/TX DMA config registers bit 12 always reads as zero (TI patch) * More "sparse" warnings removed, notably "changing" the SETUP packet to return data in USB byteorder (an API change, null effect on OMAP except for these warnings). Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/omap_udc.c | 153 +++++++++++++++++++++++++++++----------- drivers/usb/gadget/omap_udc.h | 4 +- include/asm-arm/arch-omap/usb.h | 9 +++ 3 files changed, 125 insertions(+), 41 deletions(-) (limited to 'include') diff --git a/drivers/usb/gadget/omap_udc.c b/drivers/usb/gadget/omap_udc.c index 4ec91a68f96c..a2b812af6e66 100644 --- a/drivers/usb/gadget/omap_udc.c +++ b/drivers/usb/gadget/omap_udc.c @@ -166,7 +166,7 @@ static int omap_ep_enable(struct usb_ep *_ep, maxp = le16_to_cpu (desc->wMaxPacketSize); if ((desc->bmAttributes == USB_ENDPOINT_XFER_BULK && maxp != ep->maxpacket) - || desc->wMaxPacketSize > ep->maxpacket + || le16_to_cpu(desc->wMaxPacketSize) > ep->maxpacket || !desc->wMaxPacketSize) { DBG("%s, bad %s maxpacket\n", __FUNCTION__, _ep->name); return -ERANGE; @@ -213,7 +213,7 @@ static int omap_ep_enable(struct usb_ep *_ep, ep->has_dma = 0; ep->lch = -1; use_ep(ep, UDC_EP_SEL); - UDC_CTRL_REG = UDC_RESET_EP; + UDC_CTRL_REG = udc->clr_halt; ep->ackwait = 0; deselect_ep(); @@ -537,6 +537,32 @@ static int read_fifo(struct omap_ep *ep, struct omap_req *req) /*-------------------------------------------------------------------------*/ +static inline dma_addr_t dma_csac(unsigned lch) +{ + dma_addr_t csac; + + /* omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is + * read before the DMA controller finished disabling the channel. + */ + csac = omap_readw(OMAP_DMA_CSAC(lch)); + if (csac == 0) + csac = omap_readw(OMAP_DMA_CSAC(lch)); + return csac; +} + +static inline dma_addr_t dma_cdac(unsigned lch) +{ + dma_addr_t cdac; + + /* omap 3.2/3.3 erratum: sometimes 0 is returned if CSAC/CDAC is + * read before the DMA controller finished disabling the channel. + */ + cdac = omap_readw(OMAP_DMA_CDAC(lch)); + if (cdac == 0) + cdac = omap_readw(OMAP_DMA_CDAC(lch)); + return cdac; +} + static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) { dma_addr_t end; @@ -547,7 +573,7 @@ static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) if (cpu_is_omap15xx()) return 0; - end = omap_readw(OMAP_DMA_CSAC(ep->lch)); + end = dma_csac(ep->lch); if (end == ep->dma_counter) return 0; @@ -558,14 +584,14 @@ static u16 dma_src_len(struct omap_ep *ep, dma_addr_t start) } #define DMA_DEST_LAST(x) (cpu_is_omap15xx() \ - ? OMAP_DMA_CSAC(x) /* really: CPC */ \ - : OMAP_DMA_CDAC(x)) + ? omap_readw(OMAP_DMA_CSAC(x)) /* really: CPC */ \ + : dma_cdac(x)) static u16 dma_dest_len(struct omap_ep *ep, dma_addr_t start) { dma_addr_t end; - end = omap_readw(DMA_DEST_LAST(ep->lch)); + end = DMA_DEST_LAST(ep->lch); if (end == ep->dma_counter) return 0; @@ -592,7 +618,7 @@ static void next_in_dma(struct omap_ep *ep, struct omap_req *req) : OMAP_DMA_SYNC_ELEMENT; /* measure length in either bytes or packets */ - if ((cpu_is_omap16xx() && length <= (UDC_TXN_TSC + 1)) + if ((cpu_is_omap16xx() && length <= UDC_TXN_TSC) || (cpu_is_omap15xx() && length < ep->maxpacket)) { txdma_ctrl = UDC_TXN_EOT | length; omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S8, @@ -601,15 +627,15 @@ static void next_in_dma(struct omap_ep *ep, struct omap_req *req) length = min(length / ep->maxpacket, (unsigned) UDC_TXN_TSC + 1); txdma_ctrl = length; - omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S8, - ep->ep.maxpacket, length, sync_mode); + omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S16, + ep->ep.maxpacket >> 1, length, sync_mode); length *= ep->maxpacket; } omap_set_dma_src_params(ep->lch, OMAP_DMA_PORT_EMIFF, OMAP_DMA_AMODE_POST_INC, req->req.dma + req->req.actual); omap_start_dma(ep->lch); - ep->dma_counter = omap_readw(OMAP_DMA_CSAC(ep->lch)); + ep->dma_counter = dma_csac(ep->lch); UDC_DMA_IRQ_EN_REG |= UDC_TX_DONE_IE(ep->dma_channel); UDC_TXDMA_REG(ep->dma_channel) = UDC_TXN_START | txdma_ctrl; req->dma_bytes = length; @@ -649,12 +675,12 @@ static void next_out_dma(struct omap_ep *ep, struct omap_req *req) packets = (req->req.length - req->req.actual) / ep->ep.maxpacket; packets = min(packets, (unsigned)UDC_RXN_TC + 1); req->dma_bytes = packets * ep->ep.maxpacket; - omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S8, - ep->ep.maxpacket, packets, + omap_set_dma_transfer_params(ep->lch, OMAP_DMA_DATA_TYPE_S16, + ep->ep.maxpacket >> 1, packets, OMAP_DMA_SYNC_ELEMENT); omap_set_dma_dest_params(ep->lch, OMAP_DMA_PORT_EMIFF, OMAP_DMA_AMODE_POST_INC, req->req.dma + req->req.actual); - ep->dma_counter = omap_readw(DMA_DEST_LAST(ep->lch)); + ep->dma_counter = DMA_DEST_LAST(ep->lch); UDC_RXDMA_REG(ep->dma_channel) = UDC_RXN_STOP | (packets - 1); UDC_DMA_IRQ_EN_REG |= UDC_RX_EOT_IE(ep->dma_channel); @@ -762,7 +788,7 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) reg = UDC_TXDMA_CFG_REG; else reg = UDC_RXDMA_CFG_REG; - reg |= 1 << 12; /* "pulse" activated */ + reg |= UDC_DMA_REQ; /* "pulse" activated */ ep->dma_channel = 0; ep->lch = -1; @@ -786,6 +812,11 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) ep->ep.name, dma_error, ep, &ep->lch); if (status == 0) { UDC_TXDMA_CFG_REG = reg; + /* EMIFF */ + omap_set_dma_src_burst_mode(ep->lch, + OMAP_DMA_DATA_BURST_4); + omap_set_dma_src_data_pack(ep->lch, 1); + /* TIPB */ omap_set_dma_dest_params(ep->lch, OMAP_DMA_PORT_TIPB, OMAP_DMA_AMODE_CONSTANT, @@ -796,10 +827,15 @@ static void dma_channel_claim(struct omap_ep *ep, unsigned channel) ep->ep.name, dma_error, ep, &ep->lch); if (status == 0) { UDC_RXDMA_CFG_REG = reg; + /* TIPB */ omap_set_dma_src_params(ep->lch, OMAP_DMA_PORT_TIPB, OMAP_DMA_AMODE_CONSTANT, (unsigned long) io_v2p((u32)&UDC_DATA_DMA_REG)); + /* EMIFF */ + omap_set_dma_dest_burst_mode(ep->lch, + OMAP_DMA_DATA_BURST_4); + omap_set_dma_dest_data_pack(ep->lch, 1); } } if (status) @@ -864,9 +900,13 @@ static void dma_channel_release(struct omap_ep *ep) (ep->bEndpointAddress & USB_DIR_IN) ? 't' : 'r', ep->dma_channel - 1, req); + /* NOTE: re-setting RX_REQ/TX_REQ because of a chip bug (before + * OMAP 1710 ES2.0) where reading the DMA_CFG can clear them. + */ + /* wait till current packet DMA finishes, and fifo empties */ if (ep->bEndpointAddress & USB_DIR_IN) { - UDC_TXDMA_CFG_REG &= ~mask; + UDC_TXDMA_CFG_REG = (UDC_TXDMA_CFG_REG & ~mask) | UDC_DMA_REQ; if (req) { finish_in_dma(ep, req, -ECONNRESET); @@ -879,7 +919,7 @@ static void dma_channel_release(struct omap_ep *ep) while (UDC_TXDMA_CFG_REG & mask) udelay(10); } else { - UDC_RXDMA_CFG_REG &= ~mask; + UDC_RXDMA_CFG_REG = (UDC_RXDMA_CFG_REG & ~mask) | UDC_DMA_REQ; /* dma empties the fifo */ while (UDC_RXDMA_CFG_REG & mask) @@ -1140,7 +1180,7 @@ static int omap_ep_set_halt(struct usb_ep *_ep, int value) dma_channel_claim(ep, channel); } else { use_ep(ep, 0); - UDC_CTRL_REG = UDC_RESET_EP; + UDC_CTRL_REG = ep->udc->clr_halt; ep->ackwait = 0; if (!(ep->bEndpointAddress & USB_DIR_IN)) { UDC_CTRL_REG = UDC_SET_FIFO_EN; @@ -1514,6 +1554,10 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) UDC_EP_NUM_REG = 0; } while (UDC_IRQ_SRC_REG & UDC_SETUP); +#define w_value le16_to_cpup (&u.r.wValue) +#define w_index le16_to_cpup (&u.r.wIndex) +#define w_length le16_to_cpup (&u.r.wLength) + /* Delegate almost all control requests to the gadget driver, * except for a handful of ch9 status/feature requests that * hardware doesn't autodecode _and_ the gadget API hides. @@ -1528,11 +1572,11 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) /* udc needs to know when ep != 0 is valid */ if (u.r.bRequestType != USB_RECIP_DEVICE) goto delegate; - if (u.r.wLength != 0) + if (w_length != 0) goto do_stall; udc->ep0_set_config = 1; - udc->ep0_reset_config = (u.r.wValue == 0); - VDBG("set config %d\n", u.r.wValue); + udc->ep0_reset_config = (w_value == 0); + VDBG("set config %d\n", w_value); /* update udc NOW since gadget driver may start * queueing requests immediately; clear config @@ -1548,18 +1592,18 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) /* clear endpoint halt */ if (u.r.bRequestType != USB_RECIP_ENDPOINT) goto delegate; - if (u.r.wValue != USB_ENDPOINT_HALT - || u.r.wLength != 0) + if (w_value != USB_ENDPOINT_HALT + || w_length != 0) goto do_stall; - ep = &udc->ep[u.r.wIndex & 0xf]; + ep = &udc->ep[w_index & 0xf]; if (ep != ep0) { - if (u.r.wIndex & USB_DIR_IN) + if (w_index & USB_DIR_IN) ep += 16; if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC || !ep->desc) goto do_stall; use_ep(ep, 0); - UDC_CTRL_REG = UDC_RESET_EP; + UDC_CTRL_REG = udc->clr_halt; ep->ackwait = 0; if (!(ep->bEndpointAddress & USB_DIR_IN)) { UDC_CTRL_REG = UDC_SET_FIFO_EN; @@ -1577,11 +1621,11 @@ static void ep0_irq(struct omap_udc *udc, u16 irq_src) /* set endpoint halt */ if (u.r.bRequestType != USB_RECIP_ENDPOINT) goto delegate; - if (u.r.wValue != USB_ENDPOINT_HALT - || u.r.wLength != 0) + if (w_value != USB_ENDPOINT_HALT + || w_length != 0) goto do_stall; - ep = &udc->ep[u.r.wIndex & 0xf]; - if (u.r.wIndex & USB_DIR_IN) + ep = &udc->ep[w_index & 0xf]; + if (w_index & USB_DIR_IN) ep += 16; if (ep->bmAttributes == USB_ENDPOINT_XFER_ISOC || ep == ep0 || !ep->desc) @@ -1619,13 +1663,13 @@ ep0out_status_stage: UDC_CTRL_REG = UDC_SET_FIFO_EN; UDC_EP_NUM_REG = UDC_EP_DIR; status = 0; - VDBG("GET_STATUS, interface %d\n", u.r.wIndex); + VDBG("GET_STATUS, interface %d\n", w_index); /* next, status stage */ break; default: delegate: /* activate the ep0out fifo right away */ - if (!udc->ep0_in && u.r.wLength) { + if (!udc->ep0_in && w_length) { UDC_EP_NUM_REG = 0; UDC_CTRL_REG = UDC_SET_FIFO_EN; } @@ -1636,7 +1680,11 @@ delegate: */ VDBG("SETUP %02x.%02x v%04x i%04x l%04x\n", u.r.bRequestType, u.r.bRequest, - u.r.wValue, u.r.wIndex, u.r.wLength); + w_value, w_index, w_length); + +#undef w_value +#undef w_index +#undef w_length /* The gadget driver may return an error here, * causing an immediate protocol stall. @@ -2181,14 +2229,14 @@ static int proc_otg_show(struct seq_file *s) tmp = OTG_REV_REG; trans = USB_TRANSCEIVER_CTRL_REG; - seq_printf(s, "\nOTG rev %d.%d, transceiver_ctrl %03x\n", + seq_printf(s, "\nOTG rev %d.%d, transceiver_ctrl %05x\n", tmp >> 4, tmp & 0xf, trans); tmp = OTG_SYSCON_1_REG; seq_printf(s, "otg_syscon1 %08x usb2 %s, usb1 %s, usb0 %s," FOURBITS "\n", tmp, trx_mode(USB2_TRX_MODE(tmp), trans & CONF_USB2_UNI_R), trx_mode(USB1_TRX_MODE(tmp), trans & CONF_USB1_UNI_R), - (USB0_TRX_MODE(tmp) == 0) + (USB0_TRX_MODE(tmp) == 0 && !cpu_is_omap1710()) ? "internal" : trx_mode(USB0_TRX_MODE(tmp), 1), (tmp & OTG_IDLE_EN) ? " !otg" : "", @@ -2418,6 +2466,10 @@ static inline void remove_proc_file(void) {} /* Before this controller can enumerate, we need to pick an endpoint * configuration, or "fifo_mode" That involves allocating 2KB of packet * buffer space among the endpoints we'll be operating. + * + * NOTE: as of OMAP 1710 ES2.0, writing a new endpoint config when + * UDC_SYSCON_1_REG.CFG_LOCK is set can now work. We won't use that + * capability yet though. */ static unsigned __init omap_ep_setup(char *name, u8 addr, u8 type, @@ -2690,6 +2742,19 @@ static int __init omap_udc_probe(struct device *dev) FUNC_MUX_CTRL_0_REG = tmp; } } else { + /* The transceiver may package some GPIO logic or handle + * loopback and/or transceiverless setup; if we find one, + * use it. Except for OTG, we don't _need_ to talk to one; + * but not having one probably means no VBUS detection. + */ + xceiv = otg_get_transceiver(); + if (xceiv) + type = xceiv->label; + else if (config->otg) { + DBG("OTG requires external transceiver!\n"); + goto cleanup0; + } + hmc = HMC_1610; switch (hmc) { case 0: /* POWERUP DEFAULT == 0 */ @@ -2706,25 +2771,27 @@ static int __init omap_udc_probe(struct device *dev) case 16: case 19: case 25: - xceiv = otg_get_transceiver(); if (!xceiv) { DBG("external transceiver not registered!\n"); - if (config->otg) - goto cleanup0; type = "unknown"; - } else - type = xceiv->label; + } break; case 21: /* internal loopback */ type = "loopback"; break; case 14: /* transceiverless */ + if (cpu_is_omap1710()) + goto bad_on_1710; + /* FALL THROUGH */ + case 13: + case 15: type = "no"; break; default: +bad_on_1710: ERR("unrecognized UDC HMC mode %d\n", hmc); - return -ENODEV; + goto cleanup0; } } INFO("hmc mode %d, %s transceiver\n", hmc, type); @@ -2741,6 +2808,12 @@ static int __init omap_udc_probe(struct device *dev) udc->gadget.is_otg = (config->otg != 0); #endif + /* starting with omap1710 es2.0, clear toggle is a separate bit */ + if (UDC_REV_REG >= 0x61) + udc->clr_halt = UDC_RESET_EP | UDC_CLRDATA_TOGGLE; + else + udc->clr_halt = UDC_RESET_EP; + /* USB general purpose IRQ: ep0, state changes, dma, etc */ status = request_irq(odev->resource[1].start, omap_udc_irq, SA_SAMPLE_RANDOM, driver_name, udc); diff --git a/drivers/usb/gadget/omap_udc.h b/drivers/usb/gadget/omap_udc.h index c9e68541622c..652ee4627344 100644 --- a/drivers/usb/gadget/omap_udc.h +++ b/drivers/usb/gadget/omap_udc.h @@ -20,6 +20,7 @@ #define UDC_CTRL_REG UDC_REG(0x0C) /* Endpoint control */ # define UDC_CLR_HALT (1 << 7) # define UDC_SET_HALT (1 << 6) +# define UDC_CLRDATA_TOGGLE (1 << 3) # define UDC_SET_FIFO_EN (1 << 2) # define UDC_CLR_EP (1 << 1) # define UDC_RESET_EP (1 << 0) @@ -99,6 +100,7 @@ /* DMA configuration registers: up to three channels in each direction. */ #define UDC_RXDMA_CFG_REG UDC_REG(0x40) /* 3 eps for RX DMA */ +# define UDC_DMA_REQ (1 << 12) #define UDC_TXDMA_CFG_REG UDC_REG(0x44) /* 3 eps for TX DMA */ #define UDC_DATA_DMA_REG UDC_REG(0x48) /* rx/tx fifo addr */ @@ -162,6 +164,7 @@ struct omap_udc { spinlock_t lock; struct omap_ep ep[32]; u16 devstat; + u16 clr_halt; struct otg_transceiver *transceiver; struct list_head iso; unsigned softconnect:1; @@ -171,7 +174,6 @@ struct omap_udc { unsigned ep0_set_config:1; unsigned ep0_reset_config:1; unsigned ep0_setup:1; - struct completion *done; }; diff --git a/include/asm-arm/arch-omap/usb.h b/include/asm-arm/arch-omap/usb.h index 1438c6cef0ca..054fb9a8e0c6 100644 --- a/include/asm-arm/arch-omap/usb.h +++ b/include/asm-arm/arch-omap/usb.h @@ -47,6 +47,15 @@ # define HMC_TLLATTACH (1 << 6) # define OTG_HMC(w) (((w)>>0)&0x3f) #define OTG_CTRL_REG OTG_REG32(0x0c) +# define OTG_USB2_EN (1 << 29) +# define OTG_USB2_DP (1 << 28) +# define OTG_USB2_DM (1 << 27) +# define OTG_USB1_EN (1 << 26) +# define OTG_USB1_DP (1 << 25) +# define OTG_USB1_DM (1 << 24) +# define OTG_USB0_EN (1 << 23) +# define OTG_USB0_DP (1 << 22) +# define OTG_USB0_DM (1 << 21) # define OTG_ASESSVLD (1 << 20) # define OTG_BSESSEND (1 << 19) # define OTG_BSESSVLD (1 << 18) -- cgit v1.2.3 From 1bbc169621cbe502b9143a27eb12802a0f1d43a0 Mon Sep 17 00:00:00 2001 From: David Brownell Date: Sat, 7 May 2005 13:05:13 -0700 Subject: [PATCH] USB: gadget driver updates (SETUP api change) This updates most of the gadget framework to expect SETUP packets use USB byteorder (matching the annotation in and usage in the host side stack): - definition in - gadget drivers: Ethernet/RNDIS, serial/ACM, file_storage, gadgetfs. - dummy_hcd It also includes some other similar changes as suggested by "sparse", which was used to detect byteorder bugs. Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- drivers/usb/gadget/dummy_hcd.c | 3 --- drivers/usb/gadget/ether.c | 6 +++--- drivers/usb/gadget/file_storage.c | 19 +++++++++---------- drivers/usb/gadget/inode.c | 12 ++++++------ drivers/usb/gadget/serial.c | 36 +++++++++++++++++++----------------- drivers/usb/gadget/zero.c | 6 +++--- include/linux/usb_gadget.h | 2 +- 7 files changed, 41 insertions(+), 43 deletions(-) (limited to 'include') diff --git a/drivers/usb/gadget/dummy_hcd.c b/drivers/usb/gadget/dummy_hcd.c index 73d2f24050ab..f9540adf2a4f 100644 --- a/drivers/usb/gadget/dummy_hcd.c +++ b/drivers/usb/gadget/dummy_hcd.c @@ -1267,9 +1267,6 @@ restart: struct dummy_ep *ep2; setup = *(struct usb_ctrlrequest*) urb->setup_packet; - le16_to_cpus (&setup.wIndex); - le16_to_cpus (&setup.wValue); - le16_to_cpus (&setup.wLength); if (setup.wLength != urb->transfer_buffer_length) { maybe_set_status (urb, -EOVERFLOW); goto return_urb; diff --git a/drivers/usb/gadget/ether.c b/drivers/usb/gadget/ether.c index 3830a0a0fd50..9f8413e3c10a 100644 --- a/drivers/usb/gadget/ether.c +++ b/drivers/usb/gadget/ether.c @@ -1277,9 +1277,9 @@ eth_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl) struct eth_dev *dev = get_gadget_data (gadget); struct usb_request *req = dev->req; int value = -EOPNOTSUPP; - u16 wIndex = (__force u16) ctrl->wIndex; - u16 wValue = (__force u16) ctrl->wValue; - u16 wLength = (__force u16) ctrl->wLength; + u16 wIndex = le16_to_cpu(ctrl->wIndex); + u16 wValue = le16_to_cpu(ctrl->wValue); + u16 wLength = le16_to_cpu(ctrl->wLength); /* descriptors just go into the pre-allocated ep0 buffer, * while config change events may enable network traffic. diff --git a/drivers/usb/gadget/file_storage.c b/drivers/usb/gadget/file_storage.c index f5ce45c4b2a3..4f57085619b4 100644 --- a/drivers/usb/gadget/file_storage.c +++ b/drivers/usb/gadget/file_storage.c @@ -819,7 +819,7 @@ static void inline put_be32(u8 *buf, u32 val) buf[0] = val >> 24; buf[1] = val >> 16; buf[2] = val >> 8; - buf[3] = val; + buf[3] = val & 0xff; } @@ -1277,8 +1277,8 @@ static int class_setup_req(struct fsg_dev *fsg, { struct usb_request *req = fsg->ep0req; int value = -EOPNOTSUPP; - u16 w_index = ctrl->wIndex; - u16 w_length = ctrl->wLength; + u16 w_index = le16_to_cpu(ctrl->wIndex); + u16 w_length = le16_to_cpu(ctrl->wLength); if (!fsg->config) return value; @@ -1345,7 +1345,7 @@ static int class_setup_req(struct fsg_dev *fsg, "unknown class-specific control req " "%02x.%02x v%04x i%04x l%u\n", ctrl->bRequestType, ctrl->bRequest, - ctrl->wValue, w_index, w_length); + le16_to_cpu(ctrl->wValue), w_index, w_length); return value; } @@ -1359,8 +1359,8 @@ static int standard_setup_req(struct fsg_dev *fsg, { struct usb_request *req = fsg->ep0req; int value = -EOPNOTSUPP; - u16 w_index = ctrl->wIndex; - u16 w_value = ctrl->wValue; + u16 w_index = le16_to_cpu(ctrl->wIndex); + u16 w_value = le16_to_cpu(ctrl->wValue); /* Usually this just stores reply data in the pre-allocated ep0 buffer, * but config change events will also reconfigure hardware. */ @@ -1469,7 +1469,7 @@ static int standard_setup_req(struct fsg_dev *fsg, VDBG(fsg, "unknown control req %02x.%02x v%04x i%04x l%u\n", ctrl->bRequestType, ctrl->bRequest, - w_value, w_index, ctrl->wLength); + w_value, w_index, le16_to_cpu(ctrl->wLength)); } return value; @@ -1481,7 +1481,7 @@ static int fsg_setup(struct usb_gadget *gadget, { struct fsg_dev *fsg = get_gadget_data(gadget); int rc; - int w_length = ctrl->wLength; + int w_length = le16_to_cpu(ctrl->wLength); ++fsg->ep0_req_tag; // Record arrival of a new request fsg->ep0req->context = NULL; @@ -1497,8 +1497,7 @@ static int fsg_setup(struct usb_gadget *gadget, if (rc >= 0 && rc != DELAYED_STATUS) { rc = min(rc, w_length); fsg->ep0req->length = rc; - fsg->ep0req->zero = (rc < w_length && - (rc % gadget->ep0->maxpacket) == 0); + fsg->ep0req->zero = rc < w_length; fsg->ep0req_name = (ctrl->bRequestType & USB_DIR_IN ? "ep0-in" : "ep0-out"); rc = ep0_queue(fsg); diff --git a/drivers/usb/gadget/inode.c b/drivers/usb/gadget/inode.c index 1e5e6ddef787..020815397a49 100644 --- a/drivers/usb/gadget/inode.c +++ b/drivers/usb/gadget/inode.c @@ -417,8 +417,8 @@ ep_read (struct file *fd, char __user *buf, size_t len, loff_t *ptr) goto free1; value = ep_io (data, kbuf, len); - VDEBUG (data->dev, "%s read %d OUT, status %d\n", - data->name, len, value); + VDEBUG (data->dev, "%s read %zu OUT, status %d\n", + data->name, len, (int) value); if (value >= 0 && copy_to_user (buf, kbuf, value)) value = -EFAULT; @@ -465,8 +465,8 @@ ep_write (struct file *fd, const char __user *buf, size_t len, loff_t *ptr) } value = ep_io (data, kbuf, len); - VDEBUG (data->dev, "%s write %d IN, status %d\n", - data->name, len, value); + VDEBUG (data->dev, "%s write %zu IN, status %d\n", + data->name, len, (int) value); free1: up (&data->lock); kfree (kbuf); @@ -1318,8 +1318,8 @@ gadgetfs_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl) struct usb_request *req = dev->req; int value = -EOPNOTSUPP; struct usb_gadgetfs_event *event; - u16 w_value = ctrl->wValue; - u16 w_length = ctrl->wLength; + u16 w_value = le16_to_cpu(ctrl->wValue); + u16 w_length = le16_to_cpu(ctrl->wLength); spin_lock (&dev->lock); dev->setup_abort = 0; diff --git a/drivers/usb/gadget/serial.c b/drivers/usb/gadget/serial.c index 4d591c764e38..9e4f1c6935a5 100644 --- a/drivers/usb/gadget/serial.c +++ b/drivers/usb/gadget/serial.c @@ -300,18 +300,18 @@ static int gs_build_config_buf(u8 *buf, enum usb_device_speed speed, u8 type, unsigned int index, int is_otg); static struct usb_request *gs_alloc_req(struct usb_ep *ep, unsigned int len, - int kmalloc_flags); + unsigned kmalloc_flags); static void gs_free_req(struct usb_ep *ep, struct usb_request *req); static struct gs_req_entry *gs_alloc_req_entry(struct usb_ep *ep, unsigned len, - int kmalloc_flags); + unsigned kmalloc_flags); static void gs_free_req_entry(struct usb_ep *ep, struct gs_req_entry *req); -static int gs_alloc_ports(struct gs_dev *dev, int kmalloc_flags); +static int gs_alloc_ports(struct gs_dev *dev, unsigned kmalloc_flags); static void gs_free_ports(struct gs_dev *dev); /* circular buffer */ -static struct gs_buf *gs_buf_alloc(unsigned int size, int kmalloc_flags); +static struct gs_buf *gs_buf_alloc(unsigned int size, unsigned kmalloc_flags); static void gs_buf_free(struct gs_buf *gb); static void gs_buf_clear(struct gs_buf *gb); static unsigned int gs_buf_data_avail(struct gs_buf *gb); @@ -1607,9 +1607,9 @@ static int gs_setup(struct usb_gadget *gadget, int ret = -EOPNOTSUPP; struct gs_dev *dev = get_gadget_data(gadget); struct usb_request *req = dev->dev_ctrl_req; - u16 wIndex = ctrl->wIndex; - u16 wValue = ctrl->wValue; - u16 wLength = ctrl->wLength; + u16 wIndex = le16_to_cpu(ctrl->wIndex); + u16 wValue = le16_to_cpu(ctrl->wValue); + u16 wLength = le16_to_cpu(ctrl->wLength); switch (ctrl->bRequestType & USB_TYPE_MASK) { case USB_TYPE_STANDARD: @@ -1651,9 +1651,9 @@ static int gs_setup_standard(struct usb_gadget *gadget, int ret = -EOPNOTSUPP; struct gs_dev *dev = get_gadget_data(gadget); struct usb_request *req = dev->dev_ctrl_req; - u16 wIndex = ctrl->wIndex; - u16 wValue = ctrl->wValue; - u16 wLength = ctrl->wLength; + u16 wIndex = le16_to_cpu(ctrl->wIndex); + u16 wValue = le16_to_cpu(ctrl->wValue); + u16 wLength = le16_to_cpu(ctrl->wLength); switch (ctrl->bRequest) { case USB_REQ_GET_DESCRIPTOR: @@ -1782,9 +1782,9 @@ static int gs_setup_class(struct usb_gadget *gadget, struct gs_dev *dev = get_gadget_data(gadget); struct gs_port *port = dev->dev_port[0]; /* ACM only has one port */ struct usb_request *req = dev->dev_ctrl_req; - u16 wIndex = ctrl->wIndex; - u16 wValue = ctrl->wValue; - u16 wLength = ctrl->wLength; + u16 wIndex = le16_to_cpu(ctrl->wIndex); + u16 wValue = le16_to_cpu(ctrl->wValue); + u16 wLength = le16_to_cpu(ctrl->wLength); switch (ctrl->bRequest) { case USB_CDC_REQ_SET_LINE_CODING: @@ -2119,7 +2119,8 @@ static int gs_build_config_buf(u8 *buf, enum usb_device_speed speed, * Allocate a usb_request and its buffer. Returns a pointer to the * usb_request or NULL if there is an error. */ -static struct usb_request *gs_alloc_req(struct usb_ep *ep, unsigned int len, int kmalloc_flags) +static struct usb_request * +gs_alloc_req(struct usb_ep *ep, unsigned int len, unsigned kmalloc_flags) { struct usb_request *req; @@ -2159,7 +2160,8 @@ static void gs_free_req(struct usb_ep *ep, struct usb_request *req) * Allocates a request and its buffer, using the given * endpoint, buffer len, and kmalloc flags. */ -static struct gs_req_entry *gs_alloc_req_entry(struct usb_ep *ep, unsigned len, int kmalloc_flags) +static struct gs_req_entry * +gs_alloc_req_entry(struct usb_ep *ep, unsigned len, unsigned kmalloc_flags) { struct gs_req_entry *req; @@ -2200,7 +2202,7 @@ static void gs_free_req_entry(struct usb_ep *ep, struct gs_req_entry *req) * * The device lock is normally held when calling this function. */ -static int gs_alloc_ports(struct gs_dev *dev, int kmalloc_flags) +static int gs_alloc_ports(struct gs_dev *dev, unsigned kmalloc_flags) { int i; struct gs_port *port; @@ -2282,7 +2284,7 @@ static void gs_free_ports(struct gs_dev *dev) * * Allocate a circular buffer and all associated memory. */ -static struct gs_buf *gs_buf_alloc(unsigned int size, int kmalloc_flags) +static struct gs_buf *gs_buf_alloc(unsigned int size, unsigned kmalloc_flags) { struct gs_buf *gb; diff --git a/drivers/usb/gadget/zero.c b/drivers/usb/gadget/zero.c index 6e49432071a1..a6e035e24479 100644 --- a/drivers/usb/gadget/zero.c +++ b/drivers/usb/gadget/zero.c @@ -919,9 +919,9 @@ zero_setup (struct usb_gadget *gadget, const struct usb_ctrlrequest *ctrl) struct zero_dev *dev = get_gadget_data (gadget); struct usb_request *req = dev->req; int value = -EOPNOTSUPP; - u16 w_index = ctrl->wIndex; - u16 w_value = ctrl->wValue; - u16 w_length = ctrl->wLength; + u16 w_index = le16_to_cpu(ctrl->wIndex); + u16 w_value = le16_to_cpu(ctrl->wValue); + u16 w_length = le16_to_cpu(ctrl->wLength); /* usually this stores reply data in the pre-allocated ep0 buffer, * but config change events will reconfigure hardware. diff --git a/include/linux/usb_gadget.h b/include/linux/usb_gadget.h index 9bba9997947b..b00f127cb447 100644 --- a/include/linux/usb_gadget.h +++ b/include/linux/usb_gadget.h @@ -711,7 +711,7 @@ usb_gadget_disconnect (struct usb_gadget *gadget) * the hardware level driver. Most calls must be handled by * the gadget driver, including descriptor and configuration * management. The 16 bit members of the setup data are in - * cpu order. Called in_interrupt; this may not sleep. Driver + * USB byte order. Called in_interrupt; this may not sleep. Driver * queues a response to ep0, or returns negative to stall. * @disconnect: Invoked after all transfers have been stopped, * when the host is disconnected. May be called in_interrupt; this -- cgit v1.2.3 From 5da0106f0b9b13afa4a902c01d4c98b002df55ff Mon Sep 17 00:00:00 2001 From: David Brownell Date: Tue, 31 May 2005 10:21:11 -0700 Subject: [PATCH] USB: wireless usb declarations This provides declarations for new requests, descriptors, and bitfields as defined in the Wireless USB 1.0 spec. Device support will involve a new "Wire Adapter" device class, connecting a USB Host to a cluster of wireless USB devices. There will be two adapter types: * Host Wireless Adapter (HWA): the downstream link is wireless, which connects a wireless USB host to wireless USB devices (not unlike like a hub) including to the second type of adapter. * Device Wireless Adapter (DWA): the upstream link is wireless, for connecting existing USB devices through wired links into the cluser. All wireless USB devices will need persistent (and secure!) key storage, and it's probable that Linux -- or device firmware -- will need to be involved with that to bootstrap the initial secure key exchange. Some user interface is required in that initial key exchange, and since the most "hands-off" one is a wired USB link, I suspect wireless operation will usually not be the only mode for wireless USB devices. (Plus, devices can recharge batteries using wired USB...) All other key exchange protocols need error prone user interactions, like copying and/or verifying keys. It'll likely be a while before we have commercial Wireless USB hardware, much less Linux implementations that know how to use it. Signed-off-by: David Brownell Signed-off-by: Greg Kroah-Hartman --- include/linux/usb_ch9.h | 183 ++++++++++++++++++++++++++++++++++++++++++++++-- 1 file changed, 176 insertions(+), 7 deletions(-) (limited to 'include') diff --git a/include/linux/usb_ch9.h b/include/linux/usb_ch9.h index f5fe94e09a03..39e7ff4ffd28 100644 --- a/include/linux/usb_ch9.h +++ b/include/linux/usb_ch9.h @@ -6,11 +6,14 @@ * * - the master/host side Linux-USB kernel driver API; * - the "usbfs" user space API; and - * - (eventually) a Linux "gadget" slave/device side driver API. + * - the Linux "gadget" slave/device/peripheral side driver API. * * USB 2.0 adds an additional "On The Go" (OTG) mode, which lets systems * act either as a USB master/host or as a USB slave/device. That means - * the master and slave side APIs will benefit from working well together. + * the master and slave side APIs benefit from working well together. + * + * There's also "Wireless USB", using low power short range radios for + * peripheral interconnection but otherwise building on the USB framework. */ #ifndef __LINUX_USB_CH9_H @@ -68,6 +71,18 @@ #define USB_REQ_SET_INTERFACE 0x0B #define USB_REQ_SYNCH_FRAME 0x0C +#define USB_REQ_SET_ENCRYPTION 0x0D /* Wireless USB */ +#define USB_REQ_GET_ENCRYPTION 0x0E +#define USB_REQ_SET_HANDSHAKE 0x0F +#define USB_REQ_GET_HANDSHAKE 0x10 +#define USB_REQ_SET_CONNECTION 0x11 +#define USB_REQ_SET_SECURITY_DATA 0x12 +#define USB_REQ_GET_SECURITY_DATA 0x13 +#define USB_REQ_SET_WUSB_DATA 0x14 +#define USB_REQ_LOOPBACK_DATA_WRITE 0x15 +#define USB_REQ_LOOPBACK_DATA_READ 0x16 +#define USB_REQ_SET_INTERFACE_DS 0x17 + /* * USB feature flags are written using USB_REQ_{CLEAR,SET}_FEATURE, and * are read as a bit array returned by USB_REQ_GET_STATUS. (So there @@ -75,10 +90,12 @@ */ #define USB_DEVICE_SELF_POWERED 0 /* (read only) */ #define USB_DEVICE_REMOTE_WAKEUP 1 /* dev may initiate wakeup */ -#define USB_DEVICE_TEST_MODE 2 /* (high speed only) */ -#define USB_DEVICE_B_HNP_ENABLE 3 /* dev may initiate HNP */ -#define USB_DEVICE_A_HNP_SUPPORT 4 /* RH port supports HNP */ -#define USB_DEVICE_A_ALT_HNP_SUPPORT 5 /* other RH port does */ +#define USB_DEVICE_TEST_MODE 2 /* (wired high speed only) */ +#define USB_DEVICE_BATTERY 2 /* (wireless) */ +#define USB_DEVICE_B_HNP_ENABLE 3 /* (otg) dev may initiate HNP */ +#define USB_DEVICE_WUSB_DEVICE 3 /* (wireless)*/ +#define USB_DEVICE_A_HNP_SUPPORT 4 /* (otg) RH port supports HNP */ +#define USB_DEVICE_A_ALT_HNP_SUPPORT 5 /* (otg) other RH port does */ #define USB_DEVICE_DEBUG_MODE 6 /* (special devices only) */ #define USB_ENDPOINT_HALT 0 /* IN/OUT will STALL */ @@ -135,6 +152,13 @@ struct usb_ctrlrequest { #define USB_DT_OTG 0x09 #define USB_DT_DEBUG 0x0a #define USB_DT_INTERFACE_ASSOCIATION 0x0b +/* these are from the Wireless USB spec */ +#define USB_DT_SECURITY 0x0c +#define USB_DT_KEY 0x0d +#define USB_DT_ENCRYPTION_TYPE 0x0e +#define USB_DT_BOS 0x0f +#define USB_DT_DEVICE_CAPABILITY 0x10 +#define USB_DT_WIRELESS_ENDPOINT_COMP 0x11 /* conventional codes for class-specific descriptors */ #define USB_DT_CS_DEVICE 0x21 @@ -192,6 +216,7 @@ struct usb_device_descriptor { #define USB_CLASS_CSCID 0x0b /* chip+ smart card */ #define USB_CLASS_CONTENT_SEC 0x0d /* content security */ #define USB_CLASS_VIDEO 0x0e +#define USB_CLASS_WIRELESS_CONTROLLER 0xe0 #define USB_CLASS_APP_SPEC 0xfe #define USB_CLASS_VENDOR_SPEC 0xff @@ -223,6 +248,7 @@ struct usb_config_descriptor { #define USB_CONFIG_ATT_ONE (1 << 7) /* must be set */ #define USB_CONFIG_ATT_SELFPOWER (1 << 6) /* self powered */ #define USB_CONFIG_ATT_WAKEUP (1 << 5) /* can wakeup */ +#define USB_CONFIG_ATT_BATTERY (1 << 4) /* battery powered */ /*-------------------------------------------------------------------------*/ @@ -289,6 +315,7 @@ struct usb_endpoint_descriptor { #define USB_ENDPOINT_XFER_ISOC 1 #define USB_ENDPOINT_XFER_BULK 2 #define USB_ENDPOINT_XFER_INT 3 +#define USB_ENDPOINT_MAX_ADJUSTABLE 0x80 /*-------------------------------------------------------------------------*/ @@ -350,6 +377,147 @@ struct usb_interface_assoc_descriptor { } __attribute__ ((packed)); +/*-------------------------------------------------------------------------*/ + +/* USB_DT_SECURITY: group of wireless security descriptors, including + * encryption types available for setting up a CC/association. + */ +struct usb_security_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __le16 wTotalLength; + __u8 bNumEncryptionTypes; +}; + +/*-------------------------------------------------------------------------*/ + +/* USB_DT_KEY: used with {GET,SET}_SECURITY_DATA; only public keys + * may be retrieved. + */ +struct usb_key_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __u8 tTKID[3]; + __u8 bReserved; + __u8 bKeyData[0]; +}; + +/*-------------------------------------------------------------------------*/ + +/* USB_DT_ENCRYPTION_TYPE: bundled in DT_SECURITY groups */ +struct usb_encryption_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __u8 bEncryptionType; +#define USB_ENC_TYPE_UNSECURE 0 +#define USB_ENC_TYPE_WIRED 1 /* non-wireless mode */ +#define USB_ENC_TYPE_CCM_1 2 /* aes128/cbc session */ +#define USB_ENC_TYPE_RSA_1 3 /* rsa3072/sha1 auth */ + __u8 bEncryptionValue; /* use in SET_ENCRYPTION */ + __u8 bAuthKeyIndex; +}; + + +/*-------------------------------------------------------------------------*/ + +/* USB_DT_BOS: group of wireless capabilities */ +struct usb_bos_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __le16 wTotalLength; + __u8 bNumDeviceCaps; +}; + +/*-------------------------------------------------------------------------*/ + +/* USB_DT_DEVICE_CAPABILITY: grouped with BOS */ +struct usb_dev_cap_header { + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; +}; + +#define USB_CAP_TYPE_WIRELESS_USB 1 + +struct usb_wireless_cap_descriptor { /* Ultra Wide Band */ + __u8 bLength; + __u8 bDescriptorType; + __u8 bDevCapabilityType; + + __u8 bmAttributes; +#define USB_WIRELESS_P2P_DRD (1 << 1) +#define USB_WIRELESS_BEACON_MASK (3 << 2) +#define USB_WIRELESS_BEACON_SELF (1 << 2) +#define USB_WIRELESS_BEACON_DIRECTED (2 << 2) +#define USB_WIRELESS_BEACON_NONE (3 << 2) + __le16 wPHYRates; /* bit rates, Mbps */ +#define USB_WIRELESS_PHY_53 (1 << 0) /* always set */ +#define USB_WIRELESS_PHY_80 (1 << 1) +#define USB_WIRELESS_PHY_107 (1 << 2) /* always set */ +#define USB_WIRELESS_PHY_160 (1 << 3) +#define USB_WIRELESS_PHY_200 (1 << 4) /* always set */ +#define USB_WIRELESS_PHY_320 (1 << 5) +#define USB_WIRELESS_PHY_400 (1 << 6) +#define USB_WIRELESS_PHY_480 (1 << 7) + __u8 bmTFITXPowerInfo; /* TFI power levels */ + __u8 bmFFITXPowerInfo; /* FFI power levels */ + __le16 bmBandGroup; + __u8 bReserved; +}; + +/*-------------------------------------------------------------------------*/ + +/* USB_DT_WIRELESS_ENDPOINT_COMP: companion descriptor associated with + * each endpoint descriptor for a wireless device + */ +struct usb_wireless_ep_comp_descriptor { + __u8 bLength; + __u8 bDescriptorType; + + __u8 bMaxBurst; + __u8 bMaxSequence; + __le16 wMaxStreamDelay; + __le16 wOverTheAirPacketSize; + __u8 bOverTheAirInterval; + __u8 bmCompAttributes; +#define USB_ENDPOINT_SWITCH_MASK 0x03 /* in bmCompAttributes */ +#define USB_ENDPOINT_SWITCH_NO 0 +#define USB_ENDPOINT_SWITCH_SWITCH 1 +#define USB_ENDPOINT_SWITCH_SCALE 2 +}; + +/*-------------------------------------------------------------------------*/ + +/* USB_REQ_SET_HANDSHAKE is a four-way handshake used between a wireless + * host and a device for connection set up, mutual authentication, and + * exchanging short lived session keys. The handshake depends on a CC. + */ +struct usb_handshake { + __u8 bMessageNumber; + __u8 bStatus; + __u8 tTKID[3]; + __u8 bReserved; + __u8 CDID[16]; + __u8 nonce[16]; + __u8 MIC[8]; +}; + +/*-------------------------------------------------------------------------*/ + +/* USB_REQ_SET_CONNECTION modifies or revokes a connection context (CC). + * A CC may also be set up using non-wireless secure channels (including + * wired USB!), and some devices may support CCs with multiple hosts. + */ +struct usb_connection_context { + __u8 CHID[16]; /* persistent host id */ + __u8 CDID[16]; /* device id (unique w/in host context) */ + __u8 CK[16]; /* connection key */ +}; + /*-------------------------------------------------------------------------*/ /* USB 2.0 defines three speeds, here's how Linux identifies them */ @@ -357,7 +525,8 @@ struct usb_interface_assoc_descriptor { enum usb_device_speed { USB_SPEED_UNKNOWN = 0, /* enumerating */ USB_SPEED_LOW, USB_SPEED_FULL, /* usb 1.1 */ - USB_SPEED_HIGH /* usb 2.0 */ + USB_SPEED_HIGH, /* usb 2.0 */ + USB_SPEED_VARIABLE, /* wireless (usb 2.5) */ }; enum usb_device_state { -- cgit v1.2.3