// SPDX-License-Identifier: GPL-2.0-only /* * pata_oldpiix.c - Intel PATA/SATA controllers * * (C) 2005 Red Hat * * Some parts based on ata_piix.c by Jeff Garzik and others. * * Early PIIX differs significantly from the later PIIX as it lacks * SITRE and the slave timing registers. This means that you have to * set timing per channel, or be clever. Libata tells us whenever it * does drive selection and we use this to reload the timings. * * Because of these behaviour differences PIIX gets its own driver module. */ #include #include #include #include #include #include #include #include #include #define DRV_NAME "pata_oldpiix" #define DRV_VERSION "0.5.5" /** * oldpiix_pre_reset - probe begin * @link: ATA link * @deadline: deadline jiffies for the operation * * Set up cable type and use generic probe init */ static int oldpiix_pre_reset(struct ata_link *link, unsigned long deadline) { struct ata_port *ap = link->ap; struct pci_dev *pdev = to_pci_dev(ap->host->dev); static const struct pci_bits oldpiix_enable_bits[] = { { 0x41U, 1U, 0x80UL, 0x80UL }, /* port 0 */ { 0x43U, 1U, 0x80UL, 0x80UL }, /* port 1 */ }; if (!pci_test_config_bits(pdev, &oldpiix_enable_bits[ap->port_no])) return -ENOENT; return ata_sff_prereset(link, deadline); } /** * oldpiix_set_piomode - Initialize host controller PATA PIO timings * @ap: Port whose timings we are configuring * @adev: Device whose timings we are configuring * * Set PIO mode for device, in host controller PCI config space. * * LOCKING: * None (inherited from caller). */ static void oldpiix_set_piomode (struct ata_port *ap, struct ata_device *adev) { unsigned int pio = adev->pio_mode - XFER_PIO_0; struct pci_dev *dev = to_pci_dev(ap->host->dev); unsigned int idetm_port= ap->port_no ? 0x42 : 0x40; u16 idetm_data; int control = 0; /* * See Intel Document 298600-004 for the timing programming rules * for PIIX/ICH. Note that the early PIIX does not have the slave * timing port at 0x44. */ static const /* ISP RTC */ u8 timings[][2] = { { 0, 0 }, { 0, 0 }, { 1, 0 }, { 2, 1 }, { 2, 3 }, }; if (pio > 1) control |= 1; /* TIME */ if (ata_pio_need_iordy(adev)) control |= 2; /* IE */ /* Intel specifies that the prefetch/posting is for disk only */ if (adev->class == ATA_DEV_ATA) control |= 4; /* PPE */ pci_read_config_word(dev, idetm_port, &idetm_data); /* * Set PPE, IE and TIME as appropriate. * Clear the other drive's timing bits. */ if (adev->devno == 0) { idetm_data &= 0xCCE0; idetm_data |= control; } else { idetm_data &= 0xCC0E; idetm_data |= (control << 4); } idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8); pci_write_config_word(dev, idetm_port, idetm_data); /* Track which port is configured */ ap->private_data = adev; } /** * oldpiix_set_dmamode - Initialize host controller PATA DMA timings * @ap: Port whose timings we are configuring * @adev: Device to program * * Set MWDMA mode for device, in host controller PCI config space. * * LOCKING: * None (inherited from caller). */ static void oldpiix_set_dmamode (struct ata_port *ap, struct ata_device *adev) { struct pci_dev *dev = to_pci_dev(ap->host->dev); u8 idetm_port = ap->port_no ? 0x42 : 0x40; u16 idetm_data; static const /* ISP RTC */ u8 timings[][2] = { { 0, 0 }, { 0, 0 }, { 1, 0 }, { 2, 1 }, { 2, 3 }, }; /* * MWDMA is driven by the PIO timings. We must also enable * IORDY unconditionally along with TIME1. PPE has already * been set when the PIO timing was set. */ unsigned int mwdma = adev->dma_mode - XFER_MW_DMA_0; unsigned int control; const unsigned int needed_pio[3] = { XFER_PIO_0, XFER_PIO_3, XFER_PIO_4 }; int pio = needed_pio[mwdma] - XFER_PIO_0; pci_read_config_word(dev, idetm_port, &idetm_data); control = 3; /* IORDY|TIME0 */ /* Intel specifies that the PPE functionality is for disk only */ if (adev->class == ATA_DEV_ATA) control |= 4; /* PPE enable */ /* If the drive MWDMA is faster than it can do PIO then we must force PIO into PIO0 */ if (adev->pio_mode < needed_pio[mwdma]) /* Enable DMA timing only */ control |= 8; /* PIO cycles in PIO0 */ /* Mask out the relevant control and timing bits we will load. Also clear the other drive TIME register as a precaution */ if (adev->devno == 0) { idetm_data &= 0xCCE0; idetm_data |= control; } else { idetm_data &= 0xCC0E; idetm_data |= (control << 4); } idetm_data |= (timings[pio][0] << 12) | (timings[pio][1] << 8); pci_write_config_word(dev, idetm_port, idetm_data); /* Track which port is configured */ ap->private_data = adev; } /** * oldpiix_qc_issue - command issue * @qc: command pending * * Called when the libata layer is about to issue a command. We wrap * this interface so that we can load the correct ATA timings if * necessary. Our logic also clears TIME0/TIME1 for the other device so * that, even if we get this wrong, cycles to the other device will * be made PIO0. */ static unsigned int oldpiix_qc_issue(struct ata_queued_cmd *qc) { struct ata_port *ap = qc->ap; struct ata_device *adev = qc->dev; if (adev != ap->private_data) { oldpiix_set_piomode(ap, adev); if (ata_dma_enabled(adev)) oldpiix_set_dmamode(ap, adev); } return ata_bmdma_qc_issue(qc); } static const struct scsi_host_template oldpiix_sht = { ATA_BMDMA_SHT(DRV_NAME), }; static struct ata_port_operations oldpiix_pata_ops = { .inherits = &ata_bmdma_port_ops, .qc_issue = oldpiix_qc_issue, .cable_detect = ata_cable_40wire, .set_piomode = oldpiix_set_piomode, .set_dmamode = oldpiix_set_dmamode, .prereset = oldpiix_pre_reset, }; /** * oldpiix_init_one - Register PIIX ATA PCI device with kernel services * @pdev: PCI device to register * @ent: Entry in oldpiix_pci_tbl matching with @pdev * * Called from kernel PCI layer. We probe for combined mode (sigh), * and then hand over control to libata, for it to do the rest. * * LOCKING: * Inherited from PCI layer (may sleep). * * RETURNS: * Zero on success, or -ERRNO value. */ static int oldpiix_init_one (struct pci_dev *pdev, const struct pci_device_id *ent) { static const struct ata_port_info info = { .flags = ATA_FLAG_SLAVE_POSS, .pio_mask = ATA_PIO4, .mwdma_mask = ATA_MWDMA12_ONLY, .port_ops = &oldpiix_pata_ops, }; const struct ata_port_info *ppi[] = { &info, NULL }; ata_print_version_once(&pdev->dev, DRV_VERSION); return ata_pci_bmdma_init_one(pdev, ppi, &oldpiix_sht, NULL, 0); } static const struct pci_device_id oldpiix_pci_tbl[] = { { PCI_VDEVICE(INTEL, 0x1230), }, { } /* terminate list */ }; static struct pci_driver oldpiix_pci_driver = { .name = DRV_NAME, .id_table = oldpiix_pci_tbl, .probe = oldpiix_init_one, .remove = ata_pci_remove_one, #ifdef CONFIG_PM_SLEEP .suspend = ata_pci_device_suspend, .resume = ata_pci_device_resume, #endif }; module_pci_driver(oldpiix_pci_driver); MODULE_AUTHOR("Alan Cox"); MODULE_DESCRIPTION("SCSI low-level driver for early PIIX series controllers"); MODULE_LICENSE("GPL"); MODULE_DEVICE_TABLE(pci, oldpiix_pci_tbl); MODULE_VERSION(DRV_VERSION);