/* * Linux ARCnet driver - COM90xx chipset (IO-mapped buffers) * * Written 1997 by David Woodhouse. * Written 1994-1999 by Avery Pennarun. * Written 1999-2000 by Martin Mares . * Derived from skeleton.c by Donald Becker. * * Special thanks to Contemporary Controls, Inc. (www.ccontrols.com) * for sponsoring the further development of this driver. * * ********************** * * The original copyright of skeleton.c was as follows: * * skeleton.c Written 1993 by Donald Becker. * Copyright 1993 United States Government as represented by the * Director, National Security Agency. This software may only be used * and distributed according to the terms of the GNU General Public License as * modified by SRC, incorporated herein by reference. * * ********************** * * For more details, see drivers/net/arcnet.c * * ********************** */ #define pr_fmt(fmt) "arcnet:" KBUILD_MODNAME ": " fmt #include #include #include #include #include #include #include #include #include #include #include "arcdevice.h" /* Internal function declarations */ static int com90io_found(struct net_device *dev); static void com90io_command(struct net_device *dev, int command); static int com90io_status(struct net_device *dev); static void com90io_setmask(struct net_device *dev, int mask); static int com90io_reset(struct net_device *dev, int really_reset); static void com90io_copy_to_card(struct net_device *dev, int bufnum, int offset, void *buf, int count); static void com90io_copy_from_card(struct net_device *dev, int bufnum, int offset, void *buf, int count); /* Handy defines for ARCnet specific stuff */ /* The number of low I/O ports used by the card. */ #define ARCNET_TOTAL_SIZE 16 /* COM 9026 controller chip --> ARCnet register addresses */ #define COM9026_REG_W_INTMASK 0 /* writable */ #define COM9026_REG_R_STATUS 0 /* readable */ #define COM9026_REG_W_COMMAND 1 /* writable, returns random vals on read (?) */ #define COM9026_REG_RW_CONFIG 2 /* Configuration register */ #define COM9026_REG_R_RESET 8 /* software reset (on read) */ #define COM9026_REG_RW_MEMDATA 12 /* Data port for IO-mapped memory */ #define COM9026_REG_W_ADDR_LO 14 /* Control registers for said */ #define COM9026_REG_W_ADDR_HI 15 /**************************************************************************** * * * IO-mapped operation routines * * * ****************************************************************************/ #undef ONE_AT_A_TIME_TX #undef ONE_AT_A_TIME_RX static u_char get_buffer_byte(struct net_device *dev, unsigned offset) { int ioaddr = dev->base_addr; arcnet_outb(offset >> 8, ioaddr, COM9026_REG_W_ADDR_HI); arcnet_outb(offset & 0xff, ioaddr, COM9026_REG_W_ADDR_LO); return arcnet_inb(ioaddr, COM9026_REG_RW_MEMDATA); } #ifdef ONE_AT_A_TIME_TX static void put_buffer_byte(struct net_device *dev, unsigned offset, u_char datum) { int ioaddr = dev->base_addr; arcnet_outb(offset >> 8, ioaddr, COM9026_REG_W_ADDR_HI); arcnet_outb(offset & 0xff, ioaddr, COM9026_REG_W_ADDR_LO); arcnet_outb(datum, ioaddr, COM9026_REG_RW_MEMDATA); } #endif static void get_whole_buffer(struct net_device *dev, unsigned offset, unsigned length, char *dest) { int ioaddr = dev->base_addr; arcnet_outb((offset >> 8) | AUTOINCflag, ioaddr, COM9026_REG_W_ADDR_HI); arcnet_outb(offset & 0xff, ioaddr, COM9026_REG_W_ADDR_LO); while (length--) #ifdef ONE_AT_A_TIME_RX *(dest++) = get_buffer_byte(dev, offset++); #else *(dest++) = arcnet_inb(ioaddr, COM9026_REG_RW_MEMDATA); #endif } static void put_whole_buffer(struct net_device *dev, unsigned offset, unsigned length, char *dest) { int ioaddr = dev->base_addr; arcnet_outb((offset >> 8) | AUTOINCflag, ioaddr, COM9026_REG_W_ADDR_HI); arcnet_outb(offset & 0xff, ioaddr,COM9026_REG_W_ADDR_LO); while (length--) #ifdef ONE_AT_A_TIME_TX put_buffer_byte(dev, offset++, *(dest++)); #else arcnet_outb(*(dest++), ioaddr, COM9026_REG_RW_MEMDATA); #endif } /* We cannot probe for an IO mapped card either, although we can check that * it's where we were told it was, and even autoirq */ static int __init com90io_probe(struct net_device *dev) { int ioaddr = dev->base_addr, status; unsigned long airqmask; if (BUGLVL(D_NORMAL)) { pr_info("%s\n", "COM90xx IO-mapped mode support (by David Woodhouse et el.)"); pr_info("E-mail me if you actually test this driver, please!\n"); } if (!ioaddr) { arc_printk(D_NORMAL, dev, "No autoprobe for IO mapped cards; you must specify the base address!\n"); return -ENODEV; } if (!request_region(ioaddr, ARCNET_TOTAL_SIZE, "com90io probe")) { arc_printk(D_INIT_REASONS, dev, "IO request_region %x-%x failed\n", ioaddr, ioaddr + ARCNET_TOTAL_SIZE - 1); return -ENXIO; } if (arcnet_inb(ioaddr, COM9026_REG_R_STATUS) == 0xFF) { arc_printk(D_INIT_REASONS, dev, "IO address %x empty\n", ioaddr); goto err_out; } arcnet_inb(ioaddr, COM9026_REG_R_RESET); mdelay(RESETtime); status = arcnet_inb(ioaddr, COM9026_REG_R_STATUS); if ((status & 0x9D) != (NORXflag | RECONflag | TXFREEflag | RESETflag)) { arc_printk(D_INIT_REASONS, dev, "Status invalid (%Xh)\n", status); goto err_out; } arc_printk(D_INIT_REASONS, dev, "Status after reset: %X\n", status); arcnet_outb(CFLAGScmd | RESETclear | CONFIGclear, ioaddr, COM9026_REG_W_COMMAND); arc_printk(D_INIT_REASONS, dev, "Status after reset acknowledged: %X\n", status); status = arcnet_inb(ioaddr, COM9026_REG_R_STATUS); if (status & RESETflag) { arc_printk(D_INIT_REASONS, dev, "Eternal reset (status=%Xh)\n", status); goto err_out; } arcnet_outb((0x16 | IOMAPflag) & ~ENABLE16flag, ioaddr, COM9026_REG_RW_CONFIG); /* Read first loc'n of memory */ arcnet_outb(AUTOINCflag, ioaddr, COM9026_REG_W_ADDR_HI); arcnet_outb(0, ioaddr, COM9026_REG_W_ADDR_LO); status = arcnet_inb(ioaddr, COM9026_REG_RW_MEMDATA); if (status != 0xd1) { arc_printk(D_INIT_REASONS, dev, "Signature byte not found (%Xh instead).\n", status); goto err_out; } if (!dev->irq) { /* if we do this, we're sure to get an IRQ since the * card has just reset and the NORXflag is on until * we tell it to start receiving. */ airqmask = probe_irq_on(); arcnet_outb(NORXflag, ioaddr, COM9026_REG_W_INTMASK); udelay(1); arcnet_outb(0, ioaddr, COM9026_REG_W_INTMASK); dev->irq = probe_irq_off(airqmask); if ((int)dev->irq <= 0) { arc_printk(D_INIT_REASONS, dev, "Autoprobe IRQ failed\n"); goto err_out; } } release_region(ioaddr, ARCNET_TOTAL_SIZE); /* end of probing */ return com90io_found(dev); err_out: release_region(ioaddr, ARCNET_TOTAL_SIZE); return -ENODEV; } /* Set up the struct net_device associated with this card. Called after * probing succeeds. */ static int __init com90io_found(struct net_device *dev) { struct arcnet_local *lp; int ioaddr = dev->base_addr; int err; /* Reserve the irq */ if (request_irq(dev->irq, arcnet_interrupt, 0, "arcnet (COM90xx-IO)", dev)) { arc_printk(D_NORMAL, dev, "Can't get IRQ %d!\n", dev->irq); return -ENODEV; } /* Reserve the I/O region */ if (!request_region(dev->base_addr, ARCNET_TOTAL_SIZE, "arcnet (COM90xx-IO)")) { free_irq(dev->irq, dev); return -EBUSY; } lp = netdev_priv(dev); lp->card_name = "COM90xx I/O"; lp->hw.command = com90io_command; lp->hw.status = com90io_status; lp->hw.intmask = com90io_setmask; lp->hw.reset = com90io_reset; lp->hw.owner = THIS_MODULE; lp->hw.copy_to_card = com90io_copy_to_card; lp->hw.copy_from_card = com90io_copy_from_card; lp->config = (0x16 | IOMAPflag) & ~ENABLE16flag; arcnet_outb(lp->config, ioaddr, COM9026_REG_RW_CONFIG); /* get and check the station ID from offset 1 in shmem */ dev->dev_addr[0] = get_buffer_byte(dev, 1); err = register_netdev(dev); if (err) { arcnet_outb(arcnet_inb(ioaddr, COM9026_REG_RW_CONFIG) & ~IOMAPflag, ioaddr, COM9026_REG_RW_CONFIG); free_irq(dev->irq, dev); release_region(dev->base_addr, ARCNET_TOTAL_SIZE); return err; } arc_printk(D_NORMAL, dev, "COM90IO: station %02Xh found at %03lXh, IRQ %d.\n", dev->dev_addr[0], dev->base_addr, dev->irq); return 0; } /* Do a hardware reset on the card, and set up necessary registers. * * This should be called as little as possible, because it disrupts the * token on the network (causes a RECON) and requires a significant delay. * * However, it does make sure the card is in a defined state. */ static int com90io_reset(struct net_device *dev, int really_reset) { struct arcnet_local *lp = netdev_priv(dev); short ioaddr = dev->base_addr; arc_printk(D_INIT, dev, "Resetting %s (status=%02Xh)\n", dev->name, arcnet_inb(ioaddr, COM9026_REG_R_STATUS)); if (really_reset) { /* reset the card */ arcnet_inb(ioaddr, COM9026_REG_R_RESET); mdelay(RESETtime); } /* Set the thing to IO-mapped, 8-bit mode */ lp->config = (0x1C | IOMAPflag) & ~ENABLE16flag; arcnet_outb(lp->config, ioaddr, COM9026_REG_RW_CONFIG); arcnet_outb(CFLAGScmd | RESETclear, ioaddr, COM9026_REG_W_COMMAND); /* clear flags & end reset */ arcnet_outb(CFLAGScmd | CONFIGclear, ioaddr, COM9026_REG_W_COMMAND); /* verify that the ARCnet signature byte is present */ if (get_buffer_byte(dev, 0) != TESTvalue) { arc_printk(D_NORMAL, dev, "reset failed: TESTvalue not present.\n"); return 1; } /* enable extended (512-byte) packets */ arcnet_outb(CONFIGcmd | EXTconf, ioaddr, COM9026_REG_W_COMMAND); /* done! return success. */ return 0; } static void com90io_command(struct net_device *dev, int cmd) { short ioaddr = dev->base_addr; arcnet_outb(cmd, ioaddr, COM9026_REG_W_COMMAND); } static int com90io_status(struct net_device *dev) { short ioaddr = dev->base_addr; return arcnet_inb(ioaddr, COM9026_REG_R_STATUS); } static void com90io_setmask(struct net_device *dev, int mask) { short ioaddr = dev->base_addr; arcnet_outb(mask, ioaddr, COM9026_REG_W_INTMASK); } static void com90io_copy_to_card(struct net_device *dev, int bufnum, int offset, void *buf, int count) { TIME(dev, "put_whole_buffer", count, put_whole_buffer(dev, bufnum * 512 + offset, count, buf)); } static void com90io_copy_from_card(struct net_device *dev, int bufnum, int offset, void *buf, int count) { TIME(dev, "get_whole_buffer", count, get_whole_buffer(dev, bufnum * 512 + offset, count, buf)); } static int io; /* use the insmod io= irq= shmem= options */ static int irq; static char device[9]; /* use eg. device=arc1 to change name */ module_param(io, int, 0); module_param(irq, int, 0); module_param_string(device, device, sizeof(device), 0); MODULE_LICENSE("GPL"); #ifndef MODULE static int __init com90io_setup(char *s) { int ints[4]; s = get_options(s, 4, ints); if (!ints[0]) return 0; switch (ints[0]) { default: /* ERROR */ pr_err("Too many arguments\n"); case 2: /* IRQ */ irq = ints[2]; case 1: /* IO address */ io = ints[1]; } if (*s) snprintf(device, sizeof(device), "%s", s); return 1; } __setup("com90io=", com90io_setup); #endif static struct net_device *my_dev; static int __init com90io_init(void) { struct net_device *dev; int err; dev = alloc_arcdev(device); if (!dev) return -ENOMEM; dev->base_addr = io; dev->irq = irq; if (dev->irq == 2) dev->irq = 9; err = com90io_probe(dev); if (err) { free_netdev(dev); return err; } my_dev = dev; return 0; } static void __exit com90io_exit(void) { struct net_device *dev = my_dev; int ioaddr = dev->base_addr; unregister_netdev(dev); /* In case the old driver is loaded later, * set the thing back to MMAP mode */ arcnet_outb(arcnet_inb(ioaddr, COM9026_REG_RW_CONFIG) & ~IOMAPflag, ioaddr, COM9026_REG_RW_CONFIG); free_irq(dev->irq, dev); release_region(dev->base_addr, ARCNET_TOTAL_SIZE); free_netdev(dev); } module_init(com90io_init) module_exit(com90io_exit)