1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
|
* STMicroelectronics 10/100/1000 Ethernet driver (GMAC)
Required properties:
- compatible: Should be "snps,dwmac-<ip_version>" "snps,dwmac"
For backwards compatibility: "st,spear600-gmac" is also supported.
- reg: Address and length of the register set for the device
- interrupt-parent: Should be the phandle for the interrupt controller
that services interrupts for this device
- interrupts: Should contain the STMMAC interrupts
- interrupt-names: Should contain the interrupt names "macirq"
"eth_wake_irq" if this interrupt is supported in the "interrupts"
property
- phy-mode: See ethernet.txt file in the same directory.
- snps,reset-gpio gpio number for phy reset.
- snps,reset-active-low boolean flag to indicate if phy reset is active low.
- snps,reset-delays-us is triplet of delays
The 1st cell is reset pre-delay in micro seconds.
The 2nd cell is reset pulse in micro seconds.
The 3rd cell is reset post-delay in micro seconds.
Optional properties:
- resets: Should contain a phandle to the STMMAC reset signal, if any
- reset-names: Should contain the reset signal name "stmmaceth", if a
reset phandle is given
- max-frame-size: See ethernet.txt file in the same directory
- clocks: If present, the first clock should be the GMAC main clock and
the second clock should be peripheral's register interface clock. Further
clocks may be specified in derived bindings.
- clock-names: One name for each entry in the clocks property, the
first one should be "stmmaceth" and the second one should be "pclk".
- clk_ptp_ref: this is the PTP reference clock; in case of the PTP is
available this clock is used for programming the Timestamp Addend Register.
If not passed then the system clock will be used and this is fine on some
platforms.
- tx-fifo-depth: See ethernet.txt file in the same directory
- rx-fifo-depth: See ethernet.txt file in the same directory
- snps,pbl Programmable Burst Length
- snps,aal Address-Aligned Beats
- snps,fixed-burst Program the DMA to use the fixed burst mode
- snps,mixed-burst Program the DMA to use the mixed burst mode
- snps,force_thresh_dma_mode Force DMA to use the threshold mode for
both tx and rx
- snps,force_sf_dma_mode Force DMA to use the Store and Forward
mode for both tx and rx. This flag is
ignored if force_thresh_dma_mode is set.
- snps,multicast-filter-bins: Number of multicast filter hash bins
supported by this device instance
- snps,perfect-filter-entries: Number of perfect filter entries supported
by this device instance
- AXI BUS Mode parameters: below the list of all the parameters to program the
AXI register inside the DMA module:
- snps,lpi_en: enable Low Power Interface
- snps,xit_frm: unlock on WoL
- snps,wr_osr_lmt: max write oustanding req. limit
- snps,rd_osr_lmt: max read oustanding req. limit
- snps,kbbe: do not cross 1KiB boundary.
- snps,axi_all: align address
- snps,blen: this is a vector of supported burst length.
- snps,fb: fixed-burst
- snps,mb: mixed-burst
- snps,rb: rebuild INCRx Burst
- snps,tso: this enables the TSO feature otherwise it will be managed by
MAC HW capability register.
- mdio: with compatible = "snps,dwmac-mdio", create and register mdio bus.
Examples:
stmmac_axi_setup: stmmac-axi-config {
snps,wr_osr_lmt = <0xf>;
snps,rd_osr_lmt = <0xf>;
snps,blen = <256 128 64 32 0 0 0>;
};
gmac0: ethernet@e0800000 {
compatible = "st,spear600-gmac";
reg = <0xe0800000 0x8000>;
interrupt-parent = <&vic1>;
interrupts = <24 23>;
interrupt-names = "macirq", "eth_wake_irq";
mac-address = [000000000000]; /* Filled in by U-Boot */
max-frame-size = <3800>;
phy-mode = "gmii";
snps,multicast-filter-bins = <256>;
snps,perfect-filter-entries = <128>;
rx-fifo-depth = <16384>;
tx-fifo-depth = <16384>;
clocks = <&clock>;
clock-names = "stmmaceth";
snps,axi-config = <&stmmac_axi_setup>;
mdio0 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "snps,dwmac-mdio";
phy1: ethernet-phy@0 {
};
};
};
|
