1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
|
# SPDX-License-Identifier: (GPL-2.0 OR MIT)
# Copyright 2019 Linaro Ltd.
%YAML 1.2
---
$id: http://devicetree.org/schemas/thermal/qcom-tsens.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: QCOM SoC Temperature Sensor (TSENS)
maintainers:
- Amit Kucheria <amit.kucheria@linaro.org>
description: |
QCOM SoCs have TSENS IP to allow temperature measurement. There are currently
three distinct major versions of the IP that is supported by a single driver.
The IP versions are named v0.1, v1 and v2 in the driver, where v0.1 captures
everything before v1 when there was no versioning information.
properties:
compatible:
oneOf:
- description: v0.1 of TSENS
items:
- enum:
- qcom,msm8916-tsens
- qcom,msm8974-tsens
- const: qcom,tsens-v0_1
- description: v1 of TSENS
items:
- enum:
- qcom,qcs404-tsens
- const: qcom,tsens-v1
- description: v2 of TSENS
items:
- enum:
- qcom,msm8996-tsens
- qcom,msm8998-tsens
- qcom,sdm845-tsens
- const: qcom,tsens-v2
reg:
maxItems: 2
items:
- description: TM registers
- description: SROT registers
nvmem-cells:
minItems: 1
maxItems: 2
description:
Reference to an nvmem node for the calibration data
nvmem-cells-names:
minItems: 1
maxItems: 2
items:
- enum:
- caldata
- calsel
"#qcom,sensors":
allOf:
- $ref: /schemas/types.yaml#/definitions/uint32
- minimum: 1
- maximum: 16
description:
Number of sensors enabled on this platform
"#thermal-sensor-cells":
const: 1
description:
Number of cells required to uniquely identify the thermal sensors. Since
we have multiple sensors this is set to 1
allOf:
- if:
properties:
compatible:
contains:
enum:
- qcom,msm8916-tsens
- qcom,msm8974-tsens
- qcom,qcs404-tsens
- qcom,tsens-v0_1
- qcom,tsens-v1
then:
properties:
interrupts:
items:
- description: Combined interrupt if upper or lower threshold crossed
interrupt-names:
items:
- const: uplow
else:
properties:
interrupts:
items:
- description: Combined interrupt if upper or lower threshold crossed
- description: Interrupt if critical threshold crossed
interrupt-names:
items:
- const: uplow
- const: critical
required:
- compatible
- reg
- "#qcom,sensors"
- interrupts
- interrupt-names
- "#thermal-sensor-cells"
examples:
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
// Example 1 (legacy: for pre v1 IP):
tsens1: thermal-sensor@900000 {
compatible = "qcom,msm8916-tsens", "qcom,tsens-v0_1";
reg = <0x4a9000 0x1000>, /* TM */
<0x4a8000 0x1000>; /* SROT */
nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
nvmem-cell-names = "caldata", "calsel";
interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "uplow";
#qcom,sensors = <5>;
#thermal-sensor-cells = <1>;
};
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
// Example 2 (for any platform containing v1 of the TSENS IP):
tsens2: thermal-sensor@4a9000 {
compatible = "qcom,qcs404-tsens", "qcom,tsens-v1";
reg = <0x004a9000 0x1000>, /* TM */
<0x004a8000 0x1000>; /* SROT */
nvmem-cells = <&tsens_caldata>;
nvmem-cell-names = "calib";
interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "uplow";
#qcom,sensors = <10>;
#thermal-sensor-cells = <1>;
};
- |
#include <dt-bindings/interrupt-controller/arm-gic.h>
// Example 3 (for any platform containing v2 of the TSENS IP):
tsens3: thermal-sensor@c263000 {
compatible = "qcom,sdm845-tsens", "qcom,tsens-v2";
reg = <0xc263000 0x1ff>,
<0xc222000 0x1ff>;
interrupts = <GIC_SPI 506 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 508 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "uplow", "critical";
#qcom,sensors = <13>;
#thermal-sensor-cells = <1>;
};
...
|
