1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
|
#
# For a description of the syntax of this configuration file,
# see Documentation/kbuild/kconfig-language.txt.
#
# Auxiliary display drivers configuration.
#
menuconfig AUXDISPLAY
bool "Auxiliary Display support"
---help---
Say Y here to get to see options for auxiliary display drivers.
This option alone does not add any kernel code.
If you say N, all options in this submenu will be skipped and disabled.
config CHARLCD
tristate "Character LCD core support" if COMPILE_TEST
if AUXDISPLAY
config HD44780
tristate "HD44780 Character LCD support"
depends on GPIOLIB || COMPILE_TEST
select CHARLCD
---help---
Enable support for Character LCDs using a HD44780 controller.
The LCD is accessible through the /dev/lcd char device (10, 156).
This code can either be compiled as a module, or linked into the
kernel and started at boot.
If you don't understand what all this is about, say N.
config KS0108
tristate "KS0108 LCD Controller"
depends on PARPORT_PC
default n
---help---
If you have a LCD controlled by one or more KS0108
controllers, say Y. You will need also another more specific
driver for your LCD.
Depends on Parallel Port support. If you say Y at
parport, you will be able to compile this as a module (M)
and built-in as well (Y).
To compile this as a module, choose M here:
the module will be called ks0108.
If unsure, say N.
config KS0108_PORT
hex "Parallel port where the LCD is connected"
depends on KS0108
default 0x378
---help---
The address of the parallel port where the LCD is connected.
The first standard parallel port address is 0x378.
The second standard parallel port address is 0x278.
The third standard parallel port address is 0x3BC.
You can specify a different address if you need.
If you don't know what I'm talking about, load the parport module,
and execute "dmesg" or "cat /proc/ioports". You can see there how
many parallel ports are present and which address each one has.
Usually you only need to use 0x378.
If you compile this as a module, you can still override this
using the module parameters.
config KS0108_DELAY
int "Delay between each control writing (microseconds)"
depends on KS0108
default "2"
---help---
Amount of time the ks0108 should wait between each control write
to the parallel port.
If your LCD seems to miss random writings, increment this.
If you don't know what I'm talking about, ignore it.
If you compile this as a module, you can still override this
value using the module parameters.
config CFAG12864B
tristate "CFAG12864B LCD"
depends on X86
depends on FB
depends on KS0108
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select FB_SYS_FOPS
default n
---help---
If you have a Crystalfontz 128x64 2-color LCD, cfag12864b Series,
say Y. You also need the ks0108 LCD Controller driver.
For help about how to wire your LCD to the parallel port,
check Documentation/auxdisplay/cfag12864b
Depends on the x86 arch and the framebuffer support.
The LCD framebuffer driver can be attached to a console.
It will work fine. However, you can't attach it to the fbdev driver
of the xorg server.
To compile this as a module, choose M here:
the modules will be called cfag12864b and cfag12864bfb.
If unsure, say N.
config CFAG12864B_RATE
int "Refresh rate (hertz)"
depends on CFAG12864B
default "20"
---help---
Refresh rate of the LCD.
As the LCD is not memory mapped, the driver has to make the work by
software. This means you should be careful setting this value higher.
If your CPUs are really slow or you feel the system is slowed down,
decrease the value.
Be careful modifying this value to a very high value:
You can freeze the computer, or the LCD maybe can't draw as fast as you
are requesting.
If you don't know what I'm talking about, ignore it.
If you compile this as a module, you can still override this
value using the module parameters.
config IMG_ASCII_LCD
tristate "Imagination Technologies ASCII LCD Display"
default y if MIPS_MALTA || MIPS_SEAD3
select SYSCON
help
Enable this to support the simple ASCII LCD displays found on
development boards such as the MIPS Boston, MIPS Malta & MIPS SEAD3
from Imagination Technologies.
config HT16K33
tristate "Holtek Ht16K33 LED controller with keyscan"
depends on FB && OF && I2C && INPUT
select FB_SYS_FOPS
select FB_SYS_FILLRECT
select FB_SYS_COPYAREA
select FB_SYS_IMAGEBLIT
select INPUT_MATRIXKMAP
select FB_BACKLIGHT
help
Say yes here to add support for Holtek HT16K33, RAM mapping 16*8
LED controller driver with keyscan.
endif # AUXDISPLAY
|