Merge tag 'mvebu-dt64-5.4-2' of git://git.infradead.org/linux-mvebu into arm/late

mvebu dt64 for 5.4 (part 2)

Add support for Turris Mox board (Armada 3720 SoC based)

* tag 'mvebu-dt64-5.4-2' of git://git.infradead.org/linux-mvebu: (53 commits)
  arm64: dts: marvell: add DTS for Turris Mox
  dt-bindings: marvell: document Turris Mox compatible
  arm64: dts: marvell: armada-37xx: add SPI CS1 pinctrl
  arm64: dts: marvell: Add cpu clock node on Armada 7K/8K
  arm64: dts: marvell: Convert 7k/8k usb-phy properties to phy-supply
  arm64: dts: marvell: Add 7k/8k PHYs in PCIe nodes
  arm64: dts: marvell: Add 7k/8k PHYs in USB3 nodes
  arm64: dts: marvell: Add 7k/8k per-port PHYs in SATA nodes
  arm64: dts: marvell: Add CP110 COMPHY clocks
  arm64: dts: marvell: armada-37xx: add mailbox node
  dt-bindings: gpio: Document GPIOs via Moxtet bus
  drivers: gpio: Add support for GPIOs over Moxtet bus
  bus: moxtet: Add sysfs and debugfs documentation
  dt-bindings: bus: Document moxtet bus binding
  bus: Add support for Moxtet bus
  reset: Add support for resets provided by SCMI
  firmware: arm_scmi: Add RESET protocol in SCMI v2.0
  dt-bindings: arm: Extend SCMI to support new reset protocol
  firmware: arm_scmi: Make use SCMI v2.0 fastchannel for performance protocol
  firmware: arm_scmi: Add discovery of SCMI v2.0 performance fastchannels
  ...

Link: https://lore.kernel.org/r/87h85two0r.fsf@FE-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

53 files changed, 3445 insertions, 512 deletions

diff --git a/Documentation/ABI/testing/debugfs-moxtet b/Documentation/ABI/testing/debugfs-moxtet
new file mode 100644
index 000000000000..67b1717794d8
--- /dev/null
+++ b/Documentation/ABI/testing/debugfs-moxtet
@@ -0,0 +1,23 @@
+What:		/sys/kernel/debug/moxtet/input
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Read input from the shift registers, in hexadecimal.
+		Returns N+1 bytes, where N is the number of Moxtet connected
+		modules. The first byte is from the CPU board itself.
+		Example: 101214
+			 10: CPU board with SD card
+			 12: 2 = PCIe module, 1 = IRQ not active
+			 14: 4 = Peridot module, 1 = IRQ not active
+
+What:		/sys/kernel/debug/moxtet/output
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(RW) Read last written value to the shift registers, in
+		hexadecimal, or write values to the shift registers, also
+		in hexadecimal.
+		Example: 0102
+			 01: 01 was last written, or is to be written, to the
+			     first module's shift register
+			 02: the same for second module
diff --git a/Documentation/ABI/testing/sysfs-bus-moxtet-devices b/Documentation/ABI/testing/sysfs-bus-moxtet-devices
new file mode 100644
index 000000000000..355958527fa3
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-bus-moxtet-devices
@@ -0,0 +1,17 @@
+What:		/sys/bus/moxtet/devices/moxtet-<name>.<addr>/module_description
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Moxtet module description. Format: string
+
+What:		/sys/bus/moxtet/devices/moxtet-<name>.<addr>/module_id
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Moxtet module ID. Format: %x
+
+What:		/sys/bus/moxtet/devices/moxtet-<name>.<addr>/module_name
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Moxtet module name. Format: string
diff --git a/Documentation/devicetree/bindings/arm/arm,scmi.txt b/Documentation/devicetree/bindings/arm/arm,scmi.txt
index 317a2fc3667a..083dbf96ee00 100644
--- a/Documentation/devicetree/bindings/arm/arm,scmi.txt
+++ b/Documentation/devicetree/bindings/arm/arm,scmi.txt
@@ -73,6 +73,16 @@ Required properties:
 			 as used by the firmware. Refer to  platform details
 			 for your implementation for the IDs to use.
 
+Reset signal bindings for the reset domains based on SCMI Message Protocol
+------------------------------------------------------------
+
+This binding for the SCMI reset domain providers uses the generic reset
+signal binding[5].
+
+Required properties:
+ - #reset-cells : Should be 1. Contains the reset domain ID value used
+		  by SCMI commands.
+
 SRAM and Shared Memory for SCMI
 -------------------------------
 
@@ -93,6 +103,7 @@ Required sub-node properties:
 [2] Documentation/devicetree/bindings/power/power_domain.txt
 [3] Documentation/devicetree/bindings/thermal/thermal.txt
 [4] Documentation/devicetree/bindings/sram/sram.txt
+[5] Documentation/devicetree/bindings/reset/reset.txt
 
 Example:
 
@@ -152,6 +163,11 @@ firmware {
 			reg = <0x15>;
 			#thermal-sensor-cells = <1>;
 		};
+
+		scmi_reset: protocol@16 {
+			reg = <0x16>;
+			#reset-cells = <1>;
+		};
 	};
 };
 
@@ -166,6 +182,7 @@ hdlcd@7ff60000 {
 	reg = <0 0x7ff60000 0 0x1000>;
 	clocks = <&scmi_clk 4>;
 	power-domains = <&scmi_devpd 1>;
+	resets = <&scmi_reset 10>;
 };
 
 thermal-zones {
diff --git a/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt b/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt
index eddde4faef01..f6d6642d81c0 100644
--- a/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt
+++ b/Documentation/devicetree/bindings/arm/marvell/armada-37xx.txt
@@ -48,3 +48,11 @@ avs: avs@11500 {
 	compatible = "marvell,armada-3700-avs", "syscon";
 	reg = <0x11500 0x40>;
 }
+
+
+CZ.NIC's Turris Mox SOHO router Device Tree Bindings
+----------------------------------------------------
+
+Required root node property:
+
+ - compatible: must contain "cznic,turris-mox"
diff --git a/Documentation/devicetree/bindings/bus/moxtet.txt b/Documentation/devicetree/bindings/bus/moxtet.txt
new file mode 100644
index 000000000000..fb50fc865336
--- /dev/null
+++ b/Documentation/devicetree/bindings/bus/moxtet.txt
@@ -0,0 +1,46 @@
+Turris Mox module status and configuration bus (over SPI)
+
+Required properties:
+ - compatible		: Should be "cznic,moxtet"
+ - #address-cells	: Has to be 1
+ - #size-cells		: Has to be 0
+ - spi-cpol		: Required inverted clock polarity
+ - spi-cpha		: Required shifted clock phase
+ - interrupts		: Must contain reference to the shared interrupt line
+ - interrupt-controller	: Required
+ - #interrupt-cells	: Has to be 1
+
+For other required and optional properties of SPI slave nodes please refer to
+../spi/spi-bus.txt.
+
+Required properties of subnodes:
+ - reg			: Should be position on the Moxtet bus (how many Moxtet
+			  modules are between this module and CPU module, so
+			  either 0 or a positive integer)
+
+The driver finds the devices connected to the bus by itself, but it may be
+needed to reference some of them from other parts of the device tree. In that
+case the devices can be defined as subnodes of the moxtet node.
+
+Example:
+
+	moxtet@1 {
+		compatible = "cznic,moxtet";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+		spi-max-frequency = <10000000>;
+		spi-cpol;
+		spi-cpha;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+
+		moxtet_sfp: gpio@0 {
+			compatible = "cznic,moxtet-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0>;
+		}
+	};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt b/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt
new file mode 100644
index 000000000000..410759de9f09
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-moxtet.txt
@@ -0,0 +1,18 @@
+Turris Mox Moxtet GPIO expander via Moxtet bus
+
+Required properties:
+ - compatible		: Should be "cznic,moxtet-gpio".
+ - gpio-controller	: Marks the device node as a GPIO controller.
+ - #gpio-cells		: Should be two. For consumer use see gpio.txt.
+
+Other properties are required for a Moxtet bus device, please refer to
+Documentation/devicetree/bindings/bus/moxtet.txt.
+
+Example:
+
+	moxtet_sfp: gpio@0 {
+		compatible = "cznic,moxtet-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0>;
+	}
diff --git a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
index 13e095182db4..c2489e41a801 100644
--- a/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
+++ b/Documentation/devicetree/bindings/reset/fsl,imx7-src.txt
@@ -8,6 +8,7 @@ Required properties:
 - compatible:
 	- For i.MX7 SoCs should be "fsl,imx7d-src", "syscon"
 	- For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon"
+	- For i.MX8MM SoCs should be "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon"
 - reg: should be register base and length as documented in the
   datasheet
 - interrupts: Should contain SRC interrupt
@@ -46,5 +47,6 @@ Example:
 
 
 For list of all valid reset indices see
-<dt-bindings/reset/imx7-reset.h> for i.MX7 and
-<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ
+<dt-bindings/reset/imx7-reset.h> for i.MX7,
+<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ and
+<dt-bindings/reset/imx8mq-reset.h> for i.MX8MM
diff --git a/Documentation/devicetree/bindings/reset/snps,dw-reset.txt b/Documentation/devicetree/bindings/reset/snps,dw-reset.txt
new file mode 100644
index 000000000000..f94f911dd98d
--- /dev/null
+++ b/Documentation/devicetree/bindings/reset/snps,dw-reset.txt
@@ -0,0 +1,30 @@
+Synopsys DesignWare Reset controller
+=======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+
+- compatible: should be one of the following.
+	"snps,dw-high-reset" - for active high configuration
+	"snps,dw-low-reset" - for active low configuration
+
+- reg: physical base address of the controller and length of memory mapped
+	region.
+
+- #reset-cells: must be 1.
+
+example:
+
+	dw_rst_1: reset-controller@0000 {
+		compatible = "snps,dw-high-reset";
+		reg = <0x0000 0x4>;
+		#reset-cells = <1>;
+	};
+
+	dw_rst_2: reset-controller@1000 {i
+		compatible = "snps,dw-low-reset";
+		reg = <0x1000 0x8>;
+		#reset-cells = <1>;
+	};
diff --git a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
index d7afaff5faff..05ec2a838c54 100644
--- a/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
+++ b/Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt
@@ -18,7 +18,8 @@ Required properties:
 - reg : offset and length of the device registers.
 - bus-frequency : the clock frequency for QUICC Engine.
 - fsl,qe-num-riscs: define how many RISC engines the QE has.
-- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the
+- fsl,qe-snums: This property has to be specified as '/bits/ 8' value,
+  defining the array of serial number (SNUM) values for the virtual
   threads.
 
 Optional properties:
@@ -34,6 +35,11 @@ Recommended properties
 - brg-frequency : the internal clock source frequency for baud-rate
   generators in Hz.
 
+Deprecated properties
+- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use
+  for the threads. Use fsl,qe-snums instead to not only specify the
+  number of snums, but also their values.
+
 Example:
      qe@e0100000 {
 	#address-cells = <1>;
@@ -44,6 +50,11 @@ Example:
 	reg = <e0100000 480>;
 	brg-frequency = <0>;
 	bus-frequency = <179A7B00>;
+	fsl,qe-snums = /bits/ 8 <
+		0x04 0x05 0x0C 0x0D 0x14 0x15 0x1C 0x1D
+		0x24 0x25 0x2C 0x2D 0x34 0x35 0x88 0x89
+		0x98 0x99 0xA8 0xA9 0xB8 0xB9 0xC8 0xC9
+		0xD8 0xD9 0xE8 0xE9>;
      }
 
 * Multi-User RAM (MURAM)
diff --git a/MAINTAINERS b/MAINTAINERS
index 3904f0fcfcbb..5d1868e53581 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1626,6 +1626,18 @@ F:	drivers/clocksource/timer-atlas7.c
 N:	[^a-z]sirf
 X:	drivers/gnss
 
+ARM/CZ.NIC TURRIS MOX SUPPORT
+M:	Marek Behun <marek.behun@nic.cz>
+W:	http://mox.turris.cz
+S:	Maintained
+F:	Documentation/ABI/testing/debugfs-moxtet
+F:	Documentation/ABI/testing/sysfs-bus-moxtet-devices
+F:	Documentation/devicetree/bindings/bus/moxtet.txt
+F:	Documentation/devicetree/bindings/gpio/gpio-moxtet.txt
+F:	include/linux/moxtet.h
+F:	drivers/bus/moxtet.c
+F:	drivers/gpio/gpio-moxtet.c
+
 ARM/EBSA110 MACHINE SUPPORT
 M:	Russell King <linux@armlinux.org.uk>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -15577,6 +15589,7 @@ F:	drivers/clk/clk-sc[mp]i.c
 F:	drivers/cpufreq/sc[mp]i-cpufreq.c
 F:	drivers/firmware/arm_scpi.c
 F:	drivers/firmware/arm_scmi/
+F:	drivers/reset/reset-scmi.c
 F:	include/linux/sc[mp]i_protocol.h
 
 SYSTEM RESET/SHUTDOWN DRIVERS
diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
index caed4334f27d..243338c914a4 100644
--- a/arch/arm64/boot/dts/marvell/Makefile
+++ b/arch/arm64/boot/dts/marvell/Makefile
@@ -2,6 +2,7 @@
 # Mvebu SoC Family
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
+dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-uDPU.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
 dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-clearfog-gt-8k.dtb
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
new file mode 100644
index 000000000000..d105986c6be1
--- /dev/null
+++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
@@ -0,0 +1,840 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Device Tree file for CZ.NIC Turris Mox Board
+ * 2019 by Marek Behun <marek.behun@nic.cz>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/bus/moxtet.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include "armada-372x.dtsi"
+
+/ {
+	model = "CZ.NIC Turris Mox Board";
+	compatible = "cznic,turris-mox", "marvell,armada3720",
+		     "marvell,armada3710";
+
+	aliases {
+		spi0 = &spi0;
+		ethernet1 = &eth1;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		red {
+			label = "mox:red:activity";
+			gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>;
+			linux,default-trigger = "default-on";
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		reset {
+			label = "reset";
+			linux,code = <KEY_RESTART>;
+			gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>;
+			debounce-interval = <60>;
+		};
+	};
+
+	exp_usb3_vbus: usb3-vbus {
+		compatible = "regulator-fixed";
+		regulator-name = "usb3-vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		enable-active-high;
+		regulator-always-on;
+		gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>;
+	};
+
+	usb3_phy: usb3-phy {
+		compatible = "usb-nop-xceiv";
+		vcc-supply = <&exp_usb3_vbus>;
+	};
+
+	vsdc_reg: vsdc-reg {
+		compatible = "regulator-gpio";
+		regulator-name = "vsdc";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+
+		gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+		enable-active-high;
+	};
+
+	vsdio_reg: vsdio-reg {
+		compatible = "regulator-gpio";
+		regulator-name = "vsdio";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+
+		gpios = <&gpiosb 22 GPIO_ACTIVE_HIGH>;
+		gpios-states = <0>;
+		states = <1800000 0x1
+			  3300000 0x0>;
+		enable-active-high;
+	};
+
+	sdhci1_pwrseq: sdhci1-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&gpionb 19 GPIO_ACTIVE_HIGH>;
+		status = "okay";
+	};
+
+	sfp: sfp {
+		compatible = "sff,sfp+";
+		i2c-bus = <&i2c0>;
+		los-gpio = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>;
+		tx-fault-gpio = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>;
+		tx-disable-gpio = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>;
+		rate-select0-gpio = <&moxtet_sfp 5 GPIO_ACTIVE_HIGH>;
+
+		/* enabled by U-Boot if SFP module is present */
+		status = "disabled";
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	clock-frequency = <100000>;
+	status = "okay";
+
+	rtc@6f {
+		compatible = "microchip,mcp7940x";
+		reg = <0x6f>;
+	};
+};
+
+&pcie_reset_pins {
+	function = "gpio";
+};
+
+&pcie0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie_reset_pins &pcie_clkreq_pins>;
+	status = "okay";
+	max-link-speed = <2>;
+	reset-gpios = <&gpiosb 3 GPIO_ACTIVE_LOW>;
+	phys = <&comphy1 0>;
+
+	/* enabled by U-Boot if PCIe module is present */
+	status = "disabled";
+};
+
+&uart0 {
+	status = "okay";
+};
+
+&eth0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&rgmii_pins>;
+	phy-mode = "rgmii-id";
+	phy = <&phy1>;
+	status = "okay";
+};
+
+&eth1 {
+	phy-mode = "2500base-x";
+	managed = "in-band-status";
+	phys = <&comphy0 1>;
+};
+
+&sdhci0 {
+	wp-inverted;
+	bus-width = <4>;
+	cd-gpios = <&gpionb 10 GPIO_ACTIVE_HIGH>;
+	vqmmc-supply = <&vsdc_reg>;
+	marvell,pad-type = "sd";
+	status = "okay";
+};
+
+&sdhci1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdio_pins>;
+	non-removable;
+	bus-width = <4>;
+	marvell,pad-type = "sd";
+	vqmmc-supply = <&vsdio_reg>;
+	mmc-pwrseq = <&sdhci1_pwrseq>;
+	status = "okay";
+};
+
+&spi0 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi_quad_pins &spi_cs1_pins>;
+	assigned-clocks = <&nb_periph_clk 7>;
+	assigned-clock-parents = <&tbg 1>;
+	assigned-clock-rates = <20000000>;
+
+	spi-flash@0 {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <20000000>;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "secure-firmware";
+				reg = <0x0 0x20000>;
+			};
+
+			partition@20000 {
+				label = "u-boot";
+				reg = <0x20000 0x160000>;
+			};
+
+			partition@180000 {
+				label = "u-boot-env";
+				reg = <0x180000 0x10000>;
+			};
+
+			partition@190000 {
+				label = "Rescue system";
+				reg = <0x190000 0x660000>;
+			};
+
+			partition@7f0000 {
+				label = "dtb";
+				reg = <0x7f0000 0x10000>;
+			};
+		};
+	};
+
+	moxtet: moxtet@1 {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		compatible = "cznic,moxtet";
+		reg = <1>;
+		reset-gpios = <&gpiosb 2 GPIO_ACTIVE_LOW>;
+		spi-max-frequency = <10000000>;
+		spi-cpol;
+		spi-cpha;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+		status = "okay";
+
+		moxtet_sfp: gpio@0 {
+			compatible = "cznic,moxtet-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0>;
+			status = "disabled";
+		};
+	};
+};
+
+&usb2 {
+	status = "okay";
+};
+
+&usb3 {
+	status = "okay";
+	phys = <&comphy2 0>;
+	usb-phy = <&usb3_phy>;
+};
+
+&mdio {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smi_pins>;
+	status = "okay";
+
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+
+	/* switch nodes are enabled by U-Boot if modules are present */
+	switch0@10 {
+		compatible = "marvell,mv88e6190";
+		reg = <0x10 0>;
+		dsa,member = <0 0>;
+		interrupt-parent = <&moxtet>;
+		interrupts = <MOXTET_IRQ_PERIDOT(0)>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy1: switch0phy1@1 {
+				reg = <0x1>;
+			};
+
+			switch0phy2: switch0phy2@2 {
+				reg = <0x2>;
+			};
+
+			switch0phy3: switch0phy3@3 {
+				reg = <0x3>;
+			};
+
+			switch0phy4: switch0phy4@4 {
+				reg = <0x4>;
+			};
+
+			switch0phy5: switch0phy5@5 {
+				reg = <0x5>;
+			};
+
+			switch0phy6: switch0phy6@6 {
+				reg = <0x6>;
+			};
+
+			switch0phy7: switch0phy7@7 {
+				reg = <0x7>;
+			};
+
+			switch0phy8: switch0phy8@8 {
+				reg = <0x8>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan1";
+				phy-handle = <&switch0phy1>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan2";
+				phy-handle = <&switch0phy2>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan3";
+				phy-handle = <&switch0phy3>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan4";
+				phy-handle = <&switch0phy4>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "lan5";
+				phy-handle = <&switch0phy5>;
+			};
+
+			port@6 {
+				reg = <0x6>;
+				label = "lan6";
+				phy-handle = <&switch0phy6>;
+			};
+
+			port@7 {
+				reg = <0x7>;
+				label = "lan7";
+				phy-handle = <&switch0phy7>;
+			};
+
+			port@8 {
+				reg = <0x8>;
+				label = "lan8";
+				phy-handle = <&switch0phy8>;
+			};
+
+			port@9 {
+				reg = <0x9>;
+				label = "cpu";
+				ethernet = <&eth1>;
+				phy-mode = "2500base-x";
+				managed = "in-band-status";
+			};
+
+			switch0port10: port@a {
+				reg = <0xa>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				managed = "in-band-status";
+				link = <&switch1port9 &switch2port9>;
+				status = "disabled";
+			};
+
+			port-sfp@a {
+				reg = <0xa>;
+				label = "sfp";
+				sfp = <&sfp>;
+				phy-mode = "sgmii";
+				managed = "in-band-status";
+				status = "disabled";
+			};
+		};
+	};
+
+	switch0@2 {
+		compatible = "marvell,mv88e6085";
+		reg = <0x2 0>;
+		dsa,member = <0 0>;
+		interrupt-parent = <&moxtet>;
+		interrupts = <MOXTET_IRQ_TOPAZ>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy1_topaz: switch0phy1@11 {
+				reg = <0x11>;
+			};
+
+			switch0phy2_topaz: switch0phy2@12 {
+				reg = <0x12>;
+			};
+
+			switch0phy3_topaz: switch0phy3@13 {
+				reg = <0x13>;
+			};
+
+			switch0phy4_topaz: switch0phy4@14 {
+				reg = <0x14>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan1";
+				phy-handle = <&switch0phy1_topaz>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan2";
+				phy-handle = <&switch0phy2_topaz>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan3";
+				phy-handle = <&switch0phy3_topaz>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan4";
+				phy-handle = <&switch0phy4_topaz>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "cpu";
+				phy-mode = "2500base-x";
+				managed = "in-band-status";
+				ethernet = <&eth1>;
+			};
+		};
+	};
+
+	switch1@11 {
+		compatible = "marvell,mv88e6190";
+		reg = <0x11 0>;
+		dsa,member = <0 1>;
+		interrupt-parent = <&moxtet>;
+		interrupts = <MOXTET_IRQ_PERIDOT(1)>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch1phy1: switch1phy1@1 {
+				reg = <0x1>;
+			};
+
+			switch1phy2: switch1phy2@2 {
+				reg = <0x2>;
+			};
+
+			switch1phy3: switch1phy3@3 {
+				reg = <0x3>;
+			};
+
+			switch1phy4: switch1phy4@4 {
+				reg = <0x4>;
+			};
+
+			switch1phy5: switch1phy5@5 {
+				reg = <0x5>;
+			};
+
+			switch1phy6: switch1phy6@6 {
+				reg = <0x6>;
+			};
+
+			switch1phy7: switch1phy7@7 {
+				reg = <0x7>;
+			};
+
+			switch1phy8: switch1phy8@8 {
+				reg = <0x8>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan9";
+				phy-handle = <&switch1phy1>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan10";
+				phy-handle = <&switch1phy2>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan11";
+				phy-handle = <&switch1phy3>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan12";
+				phy-handle = <&switch1phy4>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "lan13";
+				phy-handle = <&switch1phy5>;
+			};
+
+			port@6 {
+				reg = <0x6>;
+				label = "lan14";
+				phy-handle = <&switch1phy6>;
+			};
+
+			port@7 {
+				reg = <0x7>;
+				label = "lan15";
+				phy-handle = <&switch1phy7>;
+			};
+
+			port@8 {
+				reg = <0x8>;
+				label = "lan16";
+				phy-handle = <&switch1phy8>;
+			};
+
+			switch1port9: port@9 {
+				reg = <0x9>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				managed = "in-band-status";
+				link = <&switch0port10>;
+			};
+
+			switch1port10: port@a {
+				reg = <0xa>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				managed = "in-band-status";
+				link = <&switch2port9>;
+				status = "disabled";
+			};
+
+			port-sfp@a {
+				reg = <0xa>;
+				label = "sfp";
+				sfp = <&sfp>;
+				phy-mode = "sgmii";
+				managed = "in-band-status";
+				status = "disabled";
+			};
+		};
+	};
+
+	switch1@2 {
+		compatible = "marvell,mv88e6085";
+		reg = <0x2 0>;
+		dsa,member = <0 1>;
+		interrupt-parent = <&moxtet>;
+		interrupts = <MOXTET_IRQ_TOPAZ>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch1phy1_topaz: switch1phy1@11 {
+				reg = <0x11>;
+			};
+
+			switch1phy2_topaz: switch1phy2@12 {
+				reg = <0x12>;
+			};
+
+			switch1phy3_topaz: switch1phy3@13 {
+				reg = <0x13>;
+			};
+
+			switch1phy4_topaz: switch1phy4@14 {
+				reg = <0x14>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan9";
+				phy-handle = <&switch1phy1_topaz>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan10";
+				phy-handle = <&switch1phy2_topaz>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan11";
+				phy-handle = <&switch1phy3_topaz>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan12";
+				phy-handle = <&switch1phy4_topaz>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				managed = "in-band-status";
+				link = <&switch0port10>;
+			};
+		};
+	};
+
+	switch2@12 {
+		compatible = "marvell,mv88e6190";
+		reg = <0x12 0>;
+		dsa,member = <0 2>;
+		interrupt-parent = <&moxtet>;
+		interrupts = <MOXTET_IRQ_PERIDOT(2)>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch2phy1: switch2phy1@1 {
+				reg = <0x1>;
+			};
+
+			switch2phy2: switch2phy2@2 {
+				reg = <0x2>;
+			};
+
+			switch2phy3: switch2phy3@3 {
+				reg = <0x3>;
+			};
+
+			switch2phy4: switch2phy4@4 {
+				reg = <0x4>;
+			};
+
+			switch2phy5: switch2phy5@5 {
+				reg = <0x5>;
+			};
+
+			switch2phy6: switch2phy6@6 {
+				reg = <0x6>;
+			};
+
+			switch2phy7: switch2phy7@7 {
+				reg = <0x7>;
+			};
+
+			switch2phy8: switch2phy8@8 {
+				reg = <0x8>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan17";
+				phy-handle = <&switch2phy1>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan18";
+				phy-handle = <&switch2phy2>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan19";
+				phy-handle = <&switch2phy3>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan20";
+				phy-handle = <&switch2phy4>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "lan21";
+				phy-handle = <&switch2phy5>;
+			};
+
+			port@6 {
+				reg = <0x6>;
+				label = "lan22";
+				phy-handle = <&switch2phy6>;
+			};
+
+			port@7 {
+				reg = <0x7>;
+				label = "lan23";
+				phy-handle = <&switch2phy7>;
+			};
+
+			port@8 {
+				reg = <0x8>;
+				label = "lan24";
+				phy-handle = <&switch2phy8>;
+			};
+
+			switch2port9: port@9 {
+				reg = <0x9>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				managed = "in-band-status";
+				link = <&switch1port10 &switch0port10>;
+			};
+
+			port-sfp@a {
+				reg = <0xa>;
+				label = "sfp";
+				sfp = <&sfp>;
+				phy-mode = "sgmii";
+				managed = "in-band-status";
+				status = "disabled";
+			};
+		};
+	};
+
+	switch2@2 {
+		compatible = "marvell,mv88e6085";
+		reg = <0x2 0>;
+		dsa,member = <0 2>;
+		interrupt-parent = <&moxtet>;
+		interrupts = <MOXTET_IRQ_TOPAZ>;
+		status = "disabled";
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch2phy1_topaz: switch2phy1@11 {
+				reg = <0x11>;
+			};
+
+			switch2phy2_topaz: switch2phy2@12 {
+				reg = <0x12>;
+			};
+
+			switch2phy3_topaz: switch2phy3@13 {
+				reg = <0x13>;
+			};
+
+			switch2phy4_topaz: switch2phy4@14 {
+				reg = <0x14>;
+			};
+		};
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@1 {
+				reg = <0x1>;
+				label = "lan17";
+				phy-handle = <&switch2phy1_topaz>;
+			};
+
+			port@2 {
+				reg = <0x2>;
+				label = "lan18";
+				phy-handle = <&switch2phy2_topaz>;
+			};
+
+			port@3 {
+				reg = <0x3>;
+				label = "lan19";
+				phy-handle = <&switch2phy3_topaz>;
+			};
+
+			port@4 {
+				reg = <0x4>;
+				label = "lan20";
+				phy-handle = <&switch2phy4_topaz>;
+			};
+
+			port@5 {
+				reg = <0x5>;
+				label = "dsa";
+				phy-mode = "2500base-x";
+				managed = "in-band-status";
+				link = <&switch1port10 &switch0port10>;
+			};
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
index f43c43168b00..000c135e39b7 100644
--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
@@ -215,6 +215,11 @@
 					function = "spi";
 				};
 
+				spi_cs1_pins: spi-cs1-pins {
+					groups = "spi_cs1";
+					function = "spi";
+				};
+
 				i2c1_pins: i2c1-pins {
 					groups = "i2c1";
 					function = "i2c";
@@ -419,6 +424,13 @@
 				clocks = <&nb_periph_clk 15>;
 			};
 
+			rwtm: mailbox@b0000 {
+				compatible = "marvell,armada-3700-rwtm-mailbox";
+				reg = <0xb0000 0x100>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+				#mbox-cells = <1>;
+			};
+
 			sdhci1: sdhci@d0000 {
 				compatible = "marvell,armada-3700-sdhci",
 					     "marvell,sdhci-xenon";
diff --git a/arch/arm64/boot/dts/marvell/armada-7040-db.dts b/arch/arm64/boot/dts/marvell/armada-7040-db.dts
index f34ee87a0f56..a7eb4e7697a2 100644
--- a/arch/arm64/boot/dts/marvell/armada-7040-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-7040-db.dts
@@ -73,16 +73,6 @@
 		gpio = <&expander0 1 GPIO_ACTIVE_HIGH>;
 		vin-supply = <&cp0_exp_usb3_1_current_regulator>;
 	};
-
-	cp0_usb3_0_phy: cp0-usb3-0-phy {
-		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cp0_reg_usb3_0_vbus>;
-	};
-
-	cp0_usb3_1_phy: cp0-usb3-1-phy {
-		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cp0_reg_usb3_1_vbus>;
-	};
 };
 
 &i2c0 {
@@ -124,6 +114,8 @@
 
 &cp0_pcie2 {
 	status = "okay";
+	phys = <&cp0_comphy5 2>;
+	phy-names = "cp0-pcie2-x1-phy";
 };
 
 &cp0_i2c0 {
@@ -219,15 +211,36 @@
 
 &cp0_sata0 {
 	status = "okay";
+
+	sata-port@1 {
+		phys = <&cp0_comphy3 1>;
+		phy-names = "cp0-sata0-1-phy";
+	};
+};
+
+&cp0_comphy1 {
+	cp0_usbh0_con: connector {
+		compatible = "usb-a-connector";
+		phy-supply = <&cp0_reg_usb3_0_vbus>;
+	};
 };
 
 &cp0_usb3_0 {
-	usb-phy = <&cp0_usb3_0_phy>;
+	phys = <&cp0_comphy1 0>;
+	phy-names = "cp0-usb3h0-comphy";
 	status = "okay";
 };
 
+&cp0_comphy4 {
+	cp0_usbh1_con: connector {
+		compatible = "usb-a-connector";
+		phy-supply = <&cp0_reg_usb3_1_vbus>;
+	};
+};
+
 &cp0_usb3_1 {
-	usb-phy = <&cp0_usb3_1_phy>;
+	phys = <&cp0_comphy4 1>;
+	phy-names = "cp0-usb3h1-comphy";
 	status = "okay";
 };
 
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
index f275d9420d5b..bd881497b872 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-clearfog-gt-8k.dts
@@ -51,11 +51,6 @@
 		status = "okay";
 	};
 
-	usb3h0_phy: usb3_phy0 {
-		compatible = "usb-nop-xceiv";
-		vcc-supply = <&v_5v0_usb3_hst_vbus>;
-	};
-
 	sfp_cp0_eth0: sfp-cp0-eth0 {
 		compatible = "sff,sfp";
 		i2c-bus = <&cp0_i2c1>;
@@ -243,6 +238,8 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&cp0_pci0_reset_pins &cp0_wlan_disable_pins>;
 	reset-gpios = <&cp0_gpio2 0 GPIO_ACTIVE_LOW>;
+	phys = <&cp0_comphy0 0>;
+	phy-names = "cp0-pcie0-x1-phy";
 	status = "okay";
 };
 
@@ -348,6 +345,11 @@
 &cp1_sata0 {
 	pinctrl-0 = <&cp0_pci1_reset_pins>;
 	status = "okay";
+
+	sata-port@1 {
+		phys = <&cp1_comphy0 1>;
+		phy-names = "cp1-sata0-1-phy";
+	};
 };
 
 &cp1_mdio {
@@ -467,7 +469,15 @@
 	};
 };
 
+&cp1_comphy2 {
+	cp1_usbh0_con: connector {
+		compatible = "usb-a-connector";
+		phy-supply = <&v_5v0_usb3_hst_vbus>;
+	};
+};
+
 &cp1_usb3_0 {
-	usb-phy = <&usb3h0_phy>;
+	phys = <&cp1_comphy2 0>;
+	phy-names = "cp1-usb3h0-comphy";
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-db.dts b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
index d6e9c014c2f9..09fb5256f1db 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-8040-db.dts
@@ -54,11 +54,6 @@
 		vcc-supply = <&cp0_reg_usb3_0_vbus>;
 	};
 
-	cp0_usb3_1_phy: cp0-usb3-1-phy {
-		compatible = "usb-nop-xceiv";
-		vcc-supply = <&cp0_reg_usb3_1_vbus>;
-	};
-
 	cp1_reg_usb3_0_vbus: cp1-usb3-0-vbus {
 		compatible = "regulator-fixed";
 		regulator-name = "cp1-usb3h0-vbus";
@@ -108,11 +103,15 @@
 
 /* CON6 on CP0 expansion */
 &cp0_pcie0 {
+	phys = <&cp0_comphy0 0>;
+	phy-names = "cp0-pcie0-x1-phy";
 	status = "okay";
 };
 
 /* CON5 on CP0 expansion */
 &cp0_pcie2 {
+	phys = <&cp0_comphy5 2>;
+	phy-names = "cp0-pcie2-x1-phy";
 	status = "okay";
 };
 
@@ -143,6 +142,15 @@
 /* CON4 on CP0 expansion */
 &cp0_sata0 {
 	status = "okay";
+
+	sata-port@0 {
+		phys = <&cp0_comphy1 0>;
+		phy-names = "cp0-sata0-0-phy";
+	};
+	sata-port@1 {
+		phys = <&cp0_comphy3 1>;
+		phy-names = "cp0-sata0-1-phy";
+	};
 };
 
 /* CON9 on CP0 expansion */
@@ -151,9 +159,17 @@
 	status = "okay";
 };
 
+&cp0_comphy4 {
+	cp0_usbh1_con: connector {
+		compatible = "usb-a-connector";
+		phy-supply = <&cp0_reg_usb3_1_vbus>;
+	};
+};
+
 /* CON10 on CP0 expansion */
 &cp0_usb3_1 {
-	usb-phy = <&cp0_usb3_1_phy>;
+	phys = <&cp0_comphy4 1>;
+	phy-names = "cp0-usb3h1-comphy";
 	status = "okay";
 };
 
@@ -187,16 +203,22 @@
 
 /* CON6 on CP1 expansion */
 &cp1_pcie0 {
+	phys = <&cp1_comphy0 0>;
+	phy-names = "cp1-pcie0-x1-phy";
 	status = "okay";
 };
 
 /* CON7 on CP1 expansion */
 &cp1_pcie1 {
+	phys = <&cp1_comphy4 1>;
+	phy-names = "cp1-pcie1-x1-phy";
 	status = "okay";
 };
 
 /* CON5 on CP1 expansion */
 &cp1_pcie2 {
+	phys = <&cp1_comphy5 2>;
+	phy-names = "cp1-pcie2-x1-phy";
 	status = "okay";
 };
 
@@ -273,6 +295,15 @@
 /* CON4 on CP1 expansion */
 &cp1_sata0 {
 	status = "okay";
+
+	sata-port@0 {
+		phys = <&cp1_comphy1 0>;
+		phy-names = "cp1-sata0-0-phy";
+	};
+	sata-port@1 {
+		phys = <&cp1_comphy3 1>;
+		phy-names = "cp1-sata0-1-phy";
+	};
 };
 
 /* CON9 on CP1 expansion */
diff --git a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
index 205071b45a32..d250f4b2bfed 100644
--- a/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-8040-mcbin.dtsi
@@ -61,11 +61,6 @@
 		status = "okay";
 	};
 
-	usb3h0_phy: usb3_phy0 {
-		compatible = "usb-nop-xceiv";
-		vcc-supply = <&v_5v0_usb3_hst_vbus>;
-	};
-
 	sfp_eth0: sfp-eth0 {
 		/* CON15,16 - CPM lane 4 */
 		compatible = "sff,sfp";
@@ -186,6 +181,10 @@
 	reset-gpios = <&cp0_gpio2 20 GPIO_ACTIVE_LOW>;
 	ranges = <0x81000000 0x0 0xf9010000 0x0 0xf9010000 0x0 0x10000
 		  0x82000000 0x0 0xc0000000 0x0 0xc0000000 0x0 0x20000000>;
+	phys = <&cp0_comphy0 0>, <&cp0_comphy1 0>,
+	       <&cp0_comphy2 0>, <&cp0_comphy3 0>;
+	phy-names = "cp0-pcie0-x4-lane0-phy", "cp0-pcie0-x4-lane1-phy",
+		    "cp0-pcie0-x4-lane2-phy", "cp0-pcie0-x4-lane3-phy";
 	status = "okay";
 };
 
@@ -239,8 +238,13 @@
 };
 
 &cp0_sata0 {
-	/* CPM Lane 0 - U29 */
 	status = "okay";
+
+	/* CPM Lane 5 - U29 */
+	sata-port@1 {
+		phys = <&cp0_comphy5 1>;
+		phy-names = "cp0-sata0-1-phy";
+	};
 };
 
 &cp0_sdhci0 {
@@ -324,9 +328,19 @@
 };
 
 &cp1_sata0 {
+	status = "okay";
+
 	/* CPS Lane 1 - U32 */
+	sata-port@0 {
+		phys = <&cp1_comphy1 0>;
+		phy-names = "cp1-sata0-0-phy";
+	};
+
 	/* CPS Lane 3 - U31 */
-	status = "okay";
+	sata-port@1 {
+		phys = <&cp1_comphy3 1>;
+		phy-names = "cp1-sata0-1-phy";
+	};
 };
 
 &cp1_spi1 {
@@ -341,8 +355,16 @@
 	};
 };
 
+&cp1_comphy2 {
+	cp1_usbh0_con: connector {
+		compatible = "usb-a-connector";
+		phy-supply = <&v_5v0_usb3_hst_vbus>;
+	};
+};
+
 &cp1_usb3_0 {
 	/* CPS Lane 2 - CON7 */
-	usb-phy = <&usb3h0_phy>;
+	phys = <&cp1_comphy2 0>;
+	phy-names = "cp1-usb3h0-comphy";
 	status = "okay";
 };
diff --git a/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi
index ea13ae78f50d..c25bc65727b5 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806-quad.dtsi
@@ -21,6 +21,7 @@
 			reg = <0x000>;
 			enable-method = "psci";
 			#cooling-cells = <2>;
+			clocks = <&cpu_clk 0>;
 		};
 		cpu1: cpu@1 {
 			device_type = "cpu";
@@ -28,6 +29,7 @@
 			reg = <0x001>;
 			enable-method = "psci";
 			#cooling-cells = <2>;
+			clocks = <&cpu_clk 0>;
 		};
 		cpu2: cpu@100 {
 			device_type = "cpu";
@@ -35,6 +37,7 @@
 			reg = <0x100>;
 			enable-method = "psci";
 			#cooling-cells = <2>;
+			clocks = <&cpu_clk 1>;
 		};
 		cpu3: cpu@101 {
 			device_type = "cpu";
@@ -42,7 +45,7 @@
 			reg = <0x101>;
 			enable-method = "psci";
 			#cooling-cells = <2>;
+			clocks = <&cpu_clk 1>;
 		};
 	};
-
 };
diff --git a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
index 96228f93b272..d06dd198f2c7 100644
--- a/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-ap806.dtsi
@@ -280,6 +280,13 @@
 				#address-cells = <1>;
 				#size-cells = <1>;
 
+				cpu_clk: clock-cpu@278 {
+					compatible = "marvell,ap806-cpu-clock";
+					clocks = <&ap_clk 0>, <&ap_clk 1>;
+					#clock-cells = <1>;
+					reg = <0x278 0xa30>;
+				};
+
 				ap_thermal: thermal-sensor@80 {
 					compatible = "marvell,armada-ap806-thermal";
 					reg = <0x80 0x10>;
diff --git a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
index f71afb1de18f..d81944902650 100644
--- a/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-cp110.dtsi
@@ -133,6 +133,9 @@
 			compatible = "marvell,comphy-cp110";
 			reg = <0x120000 0x6000>;
 			marvell,system-controller = <&CP110_LABEL(syscon0)>;
+			clocks = <&CP110_LABEL(clk) 1 5>, <&CP110_LABEL(clk) 1 6>,
+				 <&CP110_LABEL(clk) 1 18>;
+			clock-names = "mg_clk", "mg_core_clk", "axi_clk";
 			#address-cells = <1>;
 			#size-cells = <0>;
 
@@ -306,7 +309,17 @@
 			interrupts = <107 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&CP110_LABEL(clk) 1 15>,
 				 <&CP110_LABEL(clk) 1 16>;
+			#address-cells = <1>;
+			#size-cells = <0>;
 			status = "disabled";
+
+			sata-port@0 {
+				reg = <0>;
+			};
+
+			sata-port@1 {
+				reg = <1>;
+			};
 		};
 
 		CP110_LABEL(xor0): xor@6a0000 {
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index 1851112ccc29..6b331061d34b 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -29,6 +29,16 @@ config BRCMSTB_GISB_ARB
 	  arbiter. This driver provides timeout and target abort error handling
 	  and internal bus master decoding.
 
+config MOXTET
+	tristate "CZ.NIC Turris Mox module configuration bus"
+	depends on SPI_MASTER && OF
+	help
+	  Say yes here to add support for the module configuration bus found
+	  on CZ.NIC's Turris Mox. This is needed for the ability to discover
+	  the order in which the modules are connected and to get/set some of
+	  their settings. For example the GPIOs on Mox SFP module are
+	  configured through this bus.
+
 config HISILICON_LPC
 	bool "Support for ISA I/O space on HiSilicon Hip06/7"
 	depends on ARM64 && (ARCH_HISI || COMPILE_TEST)
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index ca300b1914ce..16b43d3468c6 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -8,6 +8,7 @@ obj-$(CONFIG_ARM_CCI)		+= arm-cci.o
 
 obj-$(CONFIG_HISILICON_LPC)	+= hisi_lpc.o
 obj-$(CONFIG_BRCMSTB_GISB_ARB)	+= brcmstb_gisb.o
+obj-$(CONFIG_MOXTET)		+= moxtet.o
 
 # DPAA2 fsl-mc bus
 obj-$(CONFIG_FSL_MC_BUS)	+= fsl-mc/
diff --git a/drivers/bus/moxtet.c b/drivers/bus/moxtet.c
new file mode 100644
index 000000000000..1ee4570e7e17
--- /dev/null
+++ b/drivers/bus/moxtet.c
@@ -0,0 +1,886 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Turris Mox module configuration bus driver
+ *
+ * Copyright (C) 2019 Marek Behun <marek.behun@nic.cz>
+ */
+
+#include <dt-bindings/bus/moxtet.h>
+#include <linux/bitops.h>
+#include <linux/debugfs.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/moxtet.h>
+#include <linux/mutex.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <linux/spi/spi.h>
+
+/*
+ * @name:	module name for sysfs
+ * @hwirq_base:	base index for IRQ for this module (-1 if no IRQs)
+ * @nirqs:	how many interrupts does the shift register provide
+ * @desc:	module description for kernel log
+ */
+static const struct {
+	const char *name;
+	int hwirq_base;
+	int nirqs;
+	const char *desc;
+} mox_module_table[] = {
+	/* do not change order of this array! */
+	{ NULL,		 0,			0, NULL },
+	{ "sfp",	-1,			0, "MOX D (SFP cage)" },
+	{ "pci",	MOXTET_IRQ_PCI,		1, "MOX B (Mini-PCIe)" },
+	{ "topaz",	MOXTET_IRQ_TOPAZ,	1, "MOX C (4 port switch)" },
+	{ "peridot",	MOXTET_IRQ_PERIDOT(0),	1, "MOX E (8 port switch)" },
+	{ "usb3",	MOXTET_IRQ_USB3,	2, "MOX F (USB 3.0)" },
+	{ "pci-bridge",	-1,			0, "MOX G (Mini-PCIe bridge)" },
+};
+
+static inline bool mox_module_known(unsigned int id)
+{
+	return id >= TURRIS_MOX_MODULE_FIRST && id <= TURRIS_MOX_MODULE_LAST;
+}
+
+static inline const char *mox_module_name(unsigned int id)
+{
+	if (mox_module_known(id))
+		return mox_module_table[id].name;
+	else
+		return "unknown";
+}
+
+#define DEF_MODULE_ATTR(name, fmt, ...)					\
+static ssize_t								\
+module_##name##_show(struct device *dev, struct device_attribute *a,	\
+		     char *buf)						\
+{									\
+	struct moxtet_device *mdev = to_moxtet_device(dev);		\
+	return sprintf(buf, (fmt), __VA_ARGS__);			\
+}									\
+static DEVICE_ATTR_RO(module_##name)
+
+DEF_MODULE_ATTR(id, "0x%x\n", mdev->id);
+DEF_MODULE_ATTR(name, "%s\n", mox_module_name(mdev->id));
+DEF_MODULE_ATTR(description, "%s\n",
+		mox_module_known(mdev->id) ? mox_module_table[mdev->id].desc
+					   : "");
+
+static struct attribute *moxtet_dev_attrs[] = {
+	&dev_attr_module_id.attr,
+	&dev_attr_module_name.attr,
+	&dev_attr_module_description.attr,
+	NULL,
+};
+
+static const struct attribute_group moxtet_dev_group = {
+	.attrs = moxtet_dev_attrs,
+};
+
+static const struct attribute_group *moxtet_dev_groups[] = {
+	&moxtet_dev_group,
+	NULL,
+};
+
+static int moxtet_match(struct device *dev, struct device_driver *drv)
+{
+	struct moxtet_device *mdev = to_moxtet_device(dev);
+	struct moxtet_driver *tdrv = to_moxtet_driver(drv);
+	const enum turris_mox_module_id *t;
+
+	if (of_driver_match_device(dev, drv))
+		return 1;
+
+	if (!tdrv->id_table)
+		return 0;
+
+	for (t = tdrv->id_table; *t; ++t)
+		if (*t == mdev->id)
+			return 1;
+
+	return 0;
+}
+
+struct bus_type moxtet_bus_type = {
+	.name		= "moxtet",
+	.dev_groups	= moxtet_dev_groups,
+	.match		= moxtet_match,
+};
+EXPORT_SYMBOL_GPL(moxtet_bus_type);
+
+int __moxtet_register_driver(struct module *owner,
+			     struct moxtet_driver *mdrv)
+{
+	mdrv->driver.owner = owner;
+	mdrv->driver.bus = &moxtet_bus_type;
+	return driver_register(&mdrv->driver);
+}
+EXPORT_SYMBOL_GPL(__moxtet_register_driver);
+
+static int moxtet_dev_check(struct device *dev, void *data)
+{
+	struct moxtet_device *mdev = to_moxtet_device(dev);
+	struct moxtet_device *new_dev = data;
+
+	if (mdev->moxtet == new_dev->moxtet && mdev->id == new_dev->id &&
+	    mdev->idx == new_dev->idx)
+		return -EBUSY;
+	return 0;
+}
+
+static void moxtet_dev_release(struct device *dev)
+{
+	struct moxtet_device *mdev = to_moxtet_device(dev);
+
+	put_device(mdev->moxtet->dev);
+	kfree(mdev);
+}
+
+static struct moxtet_device *
+moxtet_alloc_device(struct moxtet *moxtet)
+{
+	struct moxtet_device *dev;
+
+	if (!get_device(moxtet->dev))
+		return NULL;
+
+	dev = kzalloc(sizeof(*dev), GFP_KERNEL);
+	if (!dev) {
+		put_device(moxtet->dev);
+		return NULL;
+	}
+
+	dev->moxtet = moxtet;
+	dev->dev.parent = moxtet->dev;
+	dev->dev.bus = &moxtet_bus_type;
+	dev->dev.release = moxtet_dev_release;
+
+	device_initialize(&dev->dev);
+
+	return dev;
+}
+
+static int moxtet_add_device(struct moxtet_device *dev)
+{
+	static DEFINE_MUTEX(add_mutex);
+	int ret;
+
+	if (dev->idx >= TURRIS_MOX_MAX_MODULES || dev->id > 0xf)
+		return -EINVAL;
+
+	dev_set_name(&dev->dev, "moxtet-%s.%u", mox_module_name(dev->id),
+		     dev->idx);
+
+	mutex_lock(&add_mutex);
+
+	ret = bus_for_each_dev(&moxtet_bus_type, NULL, dev,
+			       moxtet_dev_check);
+	if (ret)
+		goto done;
+
+	ret = device_add(&dev->dev);
+	if (ret < 0)
+		dev_err(dev->moxtet->dev, "can't add %s, status %d\n",
+			dev_name(dev->moxtet->dev), ret);
+
+done:
+	mutex_unlock(&add_mutex);
+	return ret;
+}
+
+static int __unregister(struct device *dev, void *null)
+{
+	if (dev->of_node) {
+		of_node_clear_flag(dev->of_node, OF_POPULATED);
+		of_node_put(dev->of_node);
+	}
+
+	device_unregister(dev);
+
+	return 0;
+}
+
+static struct moxtet_device *
+of_register_moxtet_device(struct moxtet *moxtet, struct device_node *nc)
+{
+	struct moxtet_device *dev;
+	u32 val;
+	int ret;
+
+	dev = moxtet_alloc_device(moxtet);
+	if (!dev) {
+		dev_err(moxtet->dev,
+			"Moxtet device alloc error for %pOF\n", nc);
+		return ERR_PTR(-ENOMEM);
+	}
+
+	ret = of_property_read_u32(nc, "reg", &val);
+	if (ret) {
+		dev_err(moxtet->dev, "%pOF has no valid 'reg' property (%d)\n",
+			nc, ret);
+		goto err_put;
+	}
+
+	dev->idx = val;
+
+	if (dev->idx >= TURRIS_MOX_MAX_MODULES) {
+		dev_err(moxtet->dev, "%pOF Moxtet address 0x%x out of range\n",
+			nc, dev->idx);
+		ret = -EINVAL;
+		goto err_put;
+	}
+
+	dev->id = moxtet->modules[dev->idx];
+
+	if (!dev->id) {
+		dev_err(moxtet->dev, "%pOF Moxtet address 0x%x is empty\n", nc,
+			dev->idx);
+		ret = -ENODEV;
+		goto err_put;
+	}
+
+	of_node_get(nc);
+	dev->dev.of_node = nc;
+
+	ret = moxtet_add_device(dev);
+	if (ret) {
+		dev_err(moxtet->dev,
+			"Moxtet device register error for %pOF\n", nc);
+		of_node_put(nc);
+		goto err_put;
+	}
+
+	return dev;
+
+err_put:
+	put_device(&dev->dev);
+	return ERR_PTR(ret);
+}
+
+static void of_register_moxtet_devices(struct moxtet *moxtet)
+{
+	struct moxtet_device *dev;
+	struct device_node *nc;
+
+	if (!moxtet->dev->of_node)
+		return;
+
+	for_each_available_child_of_node(moxtet->dev->of_node, nc) {
+		if (of_node_test_and_set_flag(nc, OF_POPULATED))
+			continue;
+		dev = of_register_moxtet_device(moxtet, nc);
+		if (IS_ERR(dev)) {
+			dev_warn(moxtet->dev,
+				 "Failed to create Moxtet device for %pOF\n",
+				 nc);
+			of_node_clear_flag(nc, OF_POPULATED);
+		}
+	}
+}
+
+static void
+moxtet_register_devices_from_topology(struct moxtet *moxtet)
+{
+	struct moxtet_device *dev;
+	int i, ret;
+
+	for (i = 0; i < moxtet->count; ++i) {
+		dev = moxtet_alloc_device(moxtet);
+		if (!dev) {
+			dev_err(moxtet->dev, "Moxtet device %u alloc error\n",
+				i);
+			continue;
+		}
+
+		dev->idx = i;
+		dev->id = moxtet->modules[i];
+
+		ret = moxtet_add_device(dev);
+		if (ret && ret != -EBUSY) {
+			put_device(&dev->dev);
+			dev_err(moxtet->dev,
+				"Moxtet device %u register error: %i\n", i,
+				ret);
+		}
+	}
+}
+
+/*
+ * @nsame:	how many modules with same id are already in moxtet->modules
+ */
+static int moxtet_set_irq(struct moxtet *moxtet, int idx, int id, int nsame)
+{
+	int i, first;
+	struct moxtet_irqpos *pos;
+
+	first = mox_module_table[id].hwirq_base +
+		nsame * mox_module_table[id].nirqs;
+
+	if (first + mox_module_table[id].nirqs > MOXTET_NIRQS)
+		return -EINVAL;
+
+	for (i = 0; i < mox_module_table[id].nirqs; ++i) {
+		pos = &moxtet->irq.position[first + i];
+		pos->idx = idx;
+		pos->bit = i;
+		moxtet->irq.exists |= BIT(first + i);
+	}
+
+	return 0;
+}
+
+static int moxtet_find_topology(struct moxtet *moxtet)
+{
+	u8 buf[TURRIS_MOX_MAX_MODULES];
+	int cnts[TURRIS_MOX_MODULE_LAST];
+	int i, ret;
+
+	memset(cnts, 0, sizeof(cnts));
+
+	ret = spi_read(to_spi_device(moxtet->dev), buf, TURRIS_MOX_MAX_MODULES);
+	if (ret < 0)
+		return ret;
+
+	if (buf[0] == TURRIS_MOX_CPU_ID_EMMC) {
+		dev_info(moxtet->dev, "Found MOX A (eMMC CPU) module\n");
+	} else if (buf[0] == TURRIS_MOX_CPU_ID_SD) {
+		dev_info(moxtet->dev, "Found MOX A (CPU) module\n");
+	} else {
+		dev_err(moxtet->dev, "Invalid Turris MOX A CPU module 0x%02x\n",
+			buf[0]);
+		return -ENODEV;
+	}
+
+	moxtet->count = 0;
+
+	for (i = 1; i < TURRIS_MOX_MAX_MODULES; ++i) {
+		int id;
+
+		if (buf[i] == 0xff)
+			break;
+
+		id = buf[i] & 0xf;
+
+		moxtet->modules[i-1] = id;
+		++moxtet->count;
+
+		if (mox_module_known(id)) {
+			dev_info(moxtet->dev, "Found %s module\n",
+				 mox_module_table[id].desc);
+
+			if (moxtet_set_irq(moxtet, i-1, id, cnts[id]++) < 0)
+				dev_err(moxtet->dev,
+					"  Cannot set IRQ for module %s\n",
+					mox_module_table[id].desc);
+		} else {
+			dev_warn(moxtet->dev,
+				 "Unknown Moxtet module found (ID 0x%02x)\n",
+				 id);
+		}
+	}
+
+	return 0;
+}
+
+static int moxtet_spi_read(struct moxtet *moxtet, u8 *buf)
+{
+	struct spi_transfer xfer = {
+		.rx_buf = buf,
+		.tx_buf = moxtet->tx,
+		.len = moxtet->count + 1
+	};
+	int ret;
+
+	mutex_lock(&moxtet->lock);
+
+	ret = spi_sync_transfer(to_spi_device(moxtet->dev), &xfer, 1);
+
+	mutex_unlock(&moxtet->lock);
+
+	return ret;
+}
+
+int moxtet_device_read(struct device *dev)
+{
+	struct moxtet_device *mdev = to_moxtet_device(dev);
+	struct moxtet *moxtet = mdev->moxtet;
+	u8 buf[TURRIS_MOX_MAX_MODULES];
+	int ret;
+
+	if (mdev->idx >= moxtet->count)
+		return -EINVAL;
+
+	ret = moxtet_spi_read(moxtet, buf);
+	if (ret < 0)
+		return ret;
+
+	return buf[mdev->idx + 1] >> 4;
+}
+EXPORT_SYMBOL_GPL(moxtet_device_read);
+
+int moxtet_device_write(struct device *dev, u8 val)
+{
+	struct moxtet_device *mdev = to_moxtet_device(dev);
+	struct moxtet *moxtet = mdev->moxtet;
+	int ret;
+
+	if (mdev->idx >= moxtet->count)
+		return -EINVAL;
+
+	mutex_lock(&moxtet->lock);
+
+	moxtet->tx[moxtet->count - mdev->idx] = val;
+
+	ret = spi_write(to_spi_device(moxtet->dev), moxtet->tx,
+			moxtet->count + 1);
+
+	mutex_unlock(&moxtet->lock);
+
+	return ret;
+}
+EXPORT_SYMBOL_GPL(moxtet_device_write);
+
+int moxtet_device_written(struct device *dev)
+{
+	struct moxtet_device *mdev = to_moxtet_device(dev);
+	struct moxtet *moxtet = mdev->moxtet;
+
+	if (mdev->idx >= moxtet->count)
+		return -EINVAL;
+
+	return moxtet->tx[moxtet->count - mdev->idx];
+}
+EXPORT_SYMBOL_GPL(moxtet_device_written);
+
+#ifdef CONFIG_DEBUG_FS
+static int moxtet_debug_open(struct inode *inode, struct file *file)
+{
+	file->private_data = inode->i_private;
+
+	return nonseekable_open(inode, file);
+}
+
+static ssize_t input_read(struct file *file, char __user *buf, size_t len,
+			  loff_t *ppos)
+{
+	struct moxtet *moxtet = file->private_data;
+	u8 bin[TURRIS_MOX_MAX_MODULES];
+	u8 hex[sizeof(buf) * 2 + 1];
+	int ret, n;
+
+	ret = moxtet_spi_read(moxtet, bin);
+	if (ret < 0)
+		return ret;
+
+	n = moxtet->count + 1;
+	bin2hex(hex, bin, n);
+
+	hex[2*n] = '\n';
+
+	return simple_read_from_buffer(buf, len, ppos, hex, 2*n + 1);
+}
+
+static const struct file_operations input_fops = {
+	.owner	= THIS_MODULE,
+	.open	= moxtet_debug_open,
+	.read	= input_read,
+	.llseek	= no_llseek,
+};
+
+static ssize_t output_read(struct file *file, char __user *buf, size_t len,
+			   loff_t *ppos)
+{
+	struct moxtet *moxtet = file->private_data;
+	u8 hex[TURRIS_MOX_MAX_MODULES * 2 + 1];
+	u8 *p = hex;
+	int i;
+
+	mutex_lock(&moxtet->lock);
+
+	for (i = 0; i < moxtet->count; ++i)
+		p = hex_byte_pack(p, moxtet->tx[moxtet->count - i]);
+
+	mutex_unlock(&moxtet->lock);
+
+	*p++ = '\n';
+
+	return simple_read_from_buffer(buf, len, ppos, hex, p - hex);
+}
+
+static ssize_t output_write(struct file *file, const char __user *buf,
+			    size_t len, loff_t *ppos)
+{
+	struct moxtet *moxtet = file->private_data;
+	u8 bin[TURRIS_MOX_MAX_MODULES];
+	u8 hex[sizeof(bin) * 2 + 1];
+	size_t res;
+	loff_t dummy = 0;
+	int err, i;
+
+	if (len > 2 * moxtet->count + 1 || len < 2 * moxtet->count)
+		return -EINVAL;
+
+	res = simple_write_to_buffer(hex, sizeof(hex), &dummy, buf, len);
+	if (res < 0)
+		return res;
+
+	if (len % 2 == 1 && hex[len - 1] != '\n')
+		return -EINVAL;
+
+	err = hex2bin(bin, hex, moxtet->count);
+	if (err < 0)
+		return -EINVAL;
+
+	mutex_lock(&moxtet->lock);
+
+	for (i = 0; i < moxtet->count; ++i)
+		moxtet->tx[moxtet->count - i] = bin[i];
+
+	err = spi_write(to_spi_device(moxtet->dev), moxtet->tx,
+			moxtet->count + 1);
+
+	mutex_unlock(&moxtet->lock);
+
+	return err < 0 ? err : len;
+}
+
+static const struct file_operations output_fops = {
+	.owner	= THIS_MODULE,
+	.open	= moxtet_debug_open,
+	.read	= output_read,
+	.write	= output_write,
+	.llseek	= no_llseek,
+};
+
+static int moxtet_register_debugfs(struct moxtet *moxtet)
+{
+	struct dentry *root, *entry;
+
+	root = debugfs_create_dir("moxtet", NULL);
+
+	if (IS_ERR(root))
+		return PTR_ERR(root);
+
+	entry = debugfs_create_file_unsafe("input", 0444, root, moxtet,
+					   &input_fops);
+	if (IS_ERR(entry))
+		goto err_remove;
+
+	entry = debugfs_create_file_unsafe("output", 0644, root, moxtet,
+					   &output_fops);
+	if (IS_ERR(entry))
+		goto err_remove;
+
+	moxtet->debugfs_root = root;
+
+	return 0;
+err_remove:
+	debugfs_remove_recursive(root);
+	return PTR_ERR(entry);
+}
+
+static void moxtet_unregister_debugfs(struct moxtet *moxtet)
+{
+	debugfs_remove_recursive(moxtet->debugfs_root);
+}
+#else
+static inline int moxtet_register_debugfs(struct moxtet *moxtet)
+{
+	return 0;
+}
+
+static inline void moxtet_unregister_debugfs(struct moxtet *moxtet)
+{
+}
+#endif
+
+static int moxtet_irq_domain_map(struct irq_domain *d, unsigned int irq,
+				 irq_hw_number_t hw)
+{
+	struct moxtet *moxtet = d->host_data;
+
+	if (hw >= MOXTET_NIRQS || !(moxtet->irq.exists & BIT(hw))) {
+		dev_err(moxtet->dev, "Invalid hw irq number\n");
+		return -EINVAL;
+	}
+
+	irq_set_chip_data(irq, d->host_data);
+	irq_set_chip_and_handler(irq, &moxtet->irq.chip, handle_level_irq);
+
+	return 0;
+}
+
+static int moxtet_irq_domain_xlate(struct irq_domain *d,
+				   struct device_node *ctrlr,
+				   const u32 *intspec, unsigned int intsize,
+				   unsigned long *out_hwirq,
+				   unsigned int *out_type)
+{
+	struct moxtet *moxtet = d->host_data;
+	int irq;
+
+	if (WARN_ON(intsize < 1))
+		return -EINVAL;
+
+	irq = intspec[0];
+
+	if (irq >= MOXTET_NIRQS || !(moxtet->irq.exists & BIT(irq)))
+		return -EINVAL;
+
+	*out_hwirq = irq;
+	*out_type = IRQ_TYPE_NONE;
+	return 0;
+}
+
+static const struct irq_domain_ops moxtet_irq_domain = {
+	.map = moxtet_irq_domain_map,
+	.xlate = moxtet_irq_domain_xlate,
+};
+
+static void moxtet_irq_mask(struct irq_data *d)
+{
+	struct moxtet *moxtet = irq_data_get_irq_chip_data(d);
+
+	moxtet->irq.masked |= BIT(d->hwirq);
+}
+
+static void moxtet_irq_unmask(struct irq_data *d)
+{
+	struct moxtet *moxtet = irq_data_get_irq_chip_data(d);
+
+	moxtet->irq.masked &= ~BIT(d->hwirq);
+}
+
+static void moxtet_irq_print_chip(struct irq_data *d, struct seq_file *p)
+{
+	struct moxtet *moxtet = irq_data_get_irq_chip_data(d);
+	struct moxtet_irqpos *pos = &moxtet->irq.position[d->hwirq];
+	int id;
+
+	id = moxtet->modules[pos->idx];
+
+	seq_printf(p, " moxtet-%s.%i#%i", mox_module_name(id), pos->idx,
+		   pos->bit);
+}
+
+static const struct irq_chip moxtet_irq_chip = {
+	.name			= "moxtet",
+	.irq_mask		= moxtet_irq_mask,
+	.irq_unmask		= moxtet_irq_unmask,
+	.irq_print_chip		= moxtet_irq_print_chip,
+};
+
+static int moxtet_irq_read(struct moxtet *moxtet, unsigned long *map)
+{
+	struct moxtet_irqpos *pos = moxtet->irq.position;
+	u8 buf[TURRIS_MOX_MAX_MODULES];
+	int i, ret;
+
+	ret = moxtet_spi_read(moxtet, buf);
+	if (ret < 0)
+		return ret;
+
+	*map = 0;
+
+	for_each_set_bit(i, &moxtet->irq.exists, MOXTET_NIRQS) {
+		if (!(buf[pos[i].idx + 1] & BIT(4 + pos[i].bit)))
+			set_bit(i, map);
+	}
+
+	return 0;
+}
+
+static irqreturn_t moxtet_irq_thread_fn(int irq, void *data)
+{
+	struct moxtet *moxtet = data;
+	unsigned long set;
+	int nhandled = 0, i, sub_irq, ret;
+
+	ret = moxtet_irq_read(moxtet, &set);
+	if (ret < 0)
+		goto out;
+
+	set &= ~moxtet->irq.masked;
+
+	do {
+		for_each_set_bit(i, &set, MOXTET_NIRQS) {
+			sub_irq = irq_find_mapping(moxtet->irq.domain, i);
+			handle_nested_irq(sub_irq);
+			dev_dbg(moxtet->dev, "%i irq\n", i);
+			++nhandled;
+		}
+
+		ret = moxtet_irq_read(moxtet, &set);
+		if (ret < 0)
+			goto out;
+
+		set &= ~moxtet->irq.masked;
+	} while (set);
+
+out:
+	return (nhandled > 0 ? IRQ_HANDLED : IRQ_NONE);
+}
+
+static void moxtet_irq_free(struct moxtet *moxtet)
+{
+	int i, irq;
+
+	for (i = 0; i < MOXTET_NIRQS; ++i) {
+		if (moxtet->irq.exists & BIT(i)) {
+			irq = irq_find_mapping(moxtet->irq.domain, i);
+			irq_dispose_mapping(irq);
+		}
+	}
+
+	irq_domain_remove(moxtet->irq.domain);
+}
+
+static int moxtet_irq_setup(struct moxtet *moxtet)
+{
+	int i, ret;
+
+	moxtet->irq.domain = irq_domain_add_simple(moxtet->dev->of_node,
+						   MOXTET_NIRQS, 0,
+						   &moxtet_irq_domain, moxtet);
+	if (moxtet->irq.domain == NULL) {
+		dev_err(moxtet->dev, "Could not add IRQ domain\n");
+		return -ENOMEM;
+	}
+
+	for (i = 0; i < MOXTET_NIRQS; ++i)
+		if (moxtet->irq.exists & BIT(i))
+			irq_create_mapping(moxtet->irq.domain, i);
+
+	moxtet->irq.chip = moxtet_irq_chip;
+	moxtet->irq.masked = ~0;
+
+	ret = request_threaded_irq(moxtet->dev_irq, NULL, moxtet_irq_thread_fn,
+				   IRQF_ONESHOT, "moxtet", moxtet);
+	if (ret < 0)
+		goto err_free;
+
+	return 0;
+
+err_free:
+	moxtet_irq_free(moxtet);
+	return ret;
+}
+
+static int moxtet_probe(struct spi_device *spi)
+{
+	struct moxtet *moxtet;
+	int ret;
+
+	ret = spi_setup(spi);
+	if (ret < 0)
+		return ret;
+
+	moxtet = devm_kzalloc(&spi->dev, sizeof(struct moxtet),
+			      GFP_KERNEL);
+	if (!moxtet)
+		return -ENOMEM;
+
+	moxtet->dev = &spi->dev;
+	spi_set_drvdata(spi, moxtet);
+
+	mutex_init(&moxtet->lock);
+
+	moxtet->dev_irq = of_irq_get(moxtet->dev->of_node, 0);
+	if (moxtet->dev_irq == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	if (moxtet->dev_irq <= 0) {
+		dev_err(moxtet->dev, "No IRQ resource found\n");
+		return -ENXIO;
+	}
+
+	ret = moxtet_find_topology(moxtet);
+	if (ret < 0)
+		return ret;
+
+	if (moxtet->irq.exists) {
+		ret = moxtet_irq_setup(moxtet);
+		if (ret < 0)
+			return ret;
+	}
+
+	of_register_moxtet_devices(moxtet);
+	moxtet_register_devices_from_topology(moxtet);
+
+	ret = moxtet_register_debugfs(moxtet);
+	if (ret < 0)
+		dev_warn(moxtet->dev, "Failed creating debugfs entries: %i\n",
+			 ret);
+
+	return 0;
+}
+
+static int moxtet_remove(struct spi_device *spi)
+{
+	struct moxtet *moxtet = spi_get_drvdata(spi);
+	int dummy;
+
+	free_irq(moxtet->dev_irq, moxtet);
+
+	moxtet_irq_free(moxtet);
+
+	moxtet_unregister_debugfs(moxtet);
+
+	dummy = device_for_each_child(moxtet->dev, NULL, __unregister);
+
+	mutex_destroy(&moxtet->lock);
+
+	return 0;
+}
+
+static const struct of_device_id moxtet_dt_ids[] = {
+	{ .compatible = "cznic,moxtet" },
+	{},
+};
+MODULE_DEVICE_TABLE(of, moxtet_dt_ids);
+
+static struct spi_driver moxtet_spi_driver = {
+	.driver = {
+		.name		= "moxtet",
+		.of_match_table = moxtet_dt_ids,
+	},
+	.probe		= moxtet_probe,
+	.remove		= moxtet_remove,
+};
+
+static int __init moxtet_init(void)
+{
+	int ret;
+
+	ret = bus_register(&moxtet_bus_type);
+	if (ret < 0) {
+		pr_err("moxtet bus registration failed: %d\n", ret);
+		goto error;
+	}
+
+	ret = spi_register_driver(&moxtet_spi_driver);
+	if (ret < 0) {
+		pr_err("moxtet spi driver registration failed: %d\n", ret);
+		goto error_bus;
+	}
+
+	return 0;
+
+error_bus:
+	bus_unregister(&moxtet_bus_type);
+error:
+	return ret;
+}
+postcore_initcall_sync(moxtet_init);
+
+static void __exit moxtet_exit(void)
+{
+	spi_unregister_driver(&moxtet_spi_driver);
+	bus_unregister(&moxtet_bus_type);
+}
+module_exit(moxtet_exit);
+
+MODULE_AUTHOR("Marek Behun <marek.behun@nic.cz>");
+MODULE_DESCRIPTION("CZ.NIC's Turris Mox module configuration bus");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/clk/clk-scmi.c b/drivers/clk/clk-scmi.c
index a2287c770d5c..886f7c5df51a 100644
--- a/drivers/clk/clk-scmi.c
+++ b/drivers/clk/clk-scmi.c
@@ -69,7 +69,7 @@ static int scmi_clk_set_rate(struct clk_hw *hw, unsigned long rate,
 {
 	struct scmi_clk *clk = to_scmi_clk(hw);
 
-	return clk->handle->clk_ops->rate_set(clk->handle, clk->id, 0, rate);
+	return clk->handle->clk_ops->rate_set(clk->handle, clk->id, rate);
 }
 
 static int scmi_clk_enable(struct clk_hw *hw)
diff --git a/drivers/firmware/arm_scmi/Makefile b/drivers/firmware/arm_scmi/Makefile
index c47d28d556b6..5f298f00a82e 100644
--- a/drivers/firmware/arm_scmi/Makefile
+++ b/drivers/firmware/arm_scmi/Makefile
@@ -2,5 +2,5 @@
 obj-y	= scmi-bus.o scmi-driver.o scmi-protocols.o
 scmi-bus-y = bus.o
 scmi-driver-y = driver.o
-scmi-protocols-y = base.o clock.o perf.o power.o sensors.o
+scmi-protocols-y = base.o clock.o perf.o power.o reset.o sensors.o
 obj-$(CONFIG_ARM_SCMI_POWER_DOMAIN) += scmi_pm_domain.o
diff --git a/drivers/firmware/arm_scmi/base.c b/drivers/firmware/arm_scmi/base.c
index 204390297f4b..f804e8af6521 100644
--- a/drivers/firmware/arm_scmi/base.c
+++ b/drivers/firmware/arm_scmi/base.c
@@ -204,7 +204,7 @@ static int scmi_base_discover_agent_get(const struct scmi_handle *handle,
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(id);
+	put_unaligned_le32(id, t->tx.buf);
 
 	ret = scmi_do_xfer(handle, t);
 	if (!ret)
diff --git a/drivers/firmware/arm_scmi/clock.c b/drivers/firmware/arm_scmi/clock.c
index 0a194af92438..32526a793f3a 100644
--- a/drivers/firmware/arm_scmi/clock.c
+++ b/drivers/firmware/arm_scmi/clock.c
@@ -56,7 +56,7 @@ struct scmi_msg_resp_clock_describe_rates {
 struct scmi_clock_set_rate {
 	__le32 flags;
 #define CLOCK_SET_ASYNC		BIT(0)
-#define CLOCK_SET_DELAYED	BIT(1)
+#define CLOCK_SET_IGNORE_RESP	BIT(1)
 #define CLOCK_SET_ROUND_UP	BIT(2)
 #define CLOCK_SET_ROUND_AUTO	BIT(3)
 	__le32 id;
@@ -67,6 +67,7 @@ struct scmi_clock_set_rate {
 struct clock_info {
 	int num_clocks;
 	int max_async_req;
+	atomic_t cur_async_req;
 	struct scmi_clock_info *clk;
 };
 
@@ -106,7 +107,7 @@ static int scmi_clock_attributes_get(const struct scmi_handle *handle,
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(clk_id);
+	put_unaligned_le32(clk_id, t->tx.buf);
 	attr = t->rx.buf;
 
 	ret = scmi_do_xfer(handle, t);
@@ -203,39 +204,47 @@ scmi_clock_rate_get(const struct scmi_handle *handle, u32 clk_id, u64 *value)
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(clk_id);
+	put_unaligned_le32(clk_id, t->tx.buf);
 
 	ret = scmi_do_xfer(handle, t);
-	if (!ret) {
-		__le32 *pval = t->rx.buf;
-
-		*value = le32_to_cpu(*pval);
-		*value |= (u64)le32_to_cpu(*(pval + 1)) << 32;
-	}
+	if (!ret)
+		*value = get_unaligned_le64(t->rx.buf);
 
 	scmi_xfer_put(handle, t);
 	return ret;
 }
 
 static int scmi_clock_rate_set(const struct scmi_handle *handle, u32 clk_id,
-			       u32 config, u64 rate)
+			       u64 rate)
 {
 	int ret;
+	u32 flags = 0;
 	struct scmi_xfer *t;
 	struct scmi_clock_set_rate *cfg;
+	struct clock_info *ci = handle->clk_priv;
 
 	ret = scmi_xfer_get_init(handle, CLOCK_RATE_SET, SCMI_PROTOCOL_CLOCK,
 				 sizeof(*cfg), 0, &t);
 	if (ret)
 		return ret;
 
+	if (ci->max_async_req &&
+	    atomic_inc_return(&ci->cur_async_req) < ci->max_async_req)
+		flags |= CLOCK_SET_ASYNC;
+
 	cfg = t->tx.buf;
-	cfg->flags = cpu_to_le32(config);
+	cfg->flags = cpu_to_le32(flags);
 	cfg->id = cpu_to_le32(clk_id);
 	cfg->value_low = cpu_to_le32(rate & 0xffffffff);
 	cfg->value_high = cpu_to_le32(rate >> 32);
 
-	ret = scmi_do_xfer(handle, t);
+	if (flags & CLOCK_SET_ASYNC)
+		ret = scmi_do_xfer_with_response(handle, t);
+	else
+		ret = scmi_do_xfer(handle, t);
+
+	if (ci->max_async_req)
+		atomic_dec(&ci->cur_async_req);
 
 	scmi_xfer_put(handle, t);
 	return ret;
diff --git a/drivers/firmware/arm_scmi/common.h b/drivers/firmware/arm_scmi/common.h
index 44fd4f9404a9..5237c2ff79fe 100644
--- a/drivers/firmware/arm_scmi/common.h
+++ b/drivers/firmware/arm_scmi/common.h
@@ -15,6 +15,8 @@
 #include <linux/scmi_protocol.h>
 #include <linux/types.h>
 
+#include <asm/unaligned.h>
+
 #define PROTOCOL_REV_MINOR_MASK	GENMASK(15, 0)
 #define PROTOCOL_REV_MAJOR_MASK	GENMASK(31, 16)
 #define PROTOCOL_REV_MAJOR(x)	(u16)(FIELD_GET(PROTOCOL_REV_MAJOR_MASK, (x)))
@@ -48,11 +50,11 @@ struct scmi_msg_resp_prot_version {
 /**
  * struct scmi_msg_hdr - Message(Tx/Rx) header
  *
- * @id: The identifier of the command being sent
- * @protocol_id: The identifier of the protocol used to send @id command
- * @seq: The token to identify the message. when a message/command returns,
- *	the platform returns the whole message header unmodified including
- *	the token
+ * @id: The identifier of the message being sent
+ * @protocol_id: The identifier of the protocol used to send @id message
+ * @seq: The token to identify the message. When a message returns, the
+ *	platform returns the whole message header unmodified including the
+ *	token
  * @status: Status of the transfer once it's complete
  * @poll_completion: Indicate if the transfer needs to be polled for
  *	completion or interrupt mode is used
@@ -84,17 +86,21 @@ struct scmi_msg {
  * @rx: Receive message, the buffer should be pre-allocated to store
  *	message. If request-ACK protocol is used, we can reuse the same
  *	buffer for the rx path as we use for the tx path.
- * @done: completion event
+ * @done: command message transmit completion event
+ * @async: pointer to delayed response message received event completion
  */
 struct scmi_xfer {
 	struct scmi_msg_hdr hdr;
 	struct scmi_msg tx;
 	struct scmi_msg rx;
 	struct completion done;
+	struct completion *async_done;
 };
 
 void scmi_xfer_put(const struct scmi_handle *h, struct scmi_xfer *xfer);
 int scmi_do_xfer(const struct scmi_handle *h, struct scmi_xfer *xfer);
+int scmi_do_xfer_with_response(const struct scmi_handle *h,
+			       struct scmi_xfer *xfer);
 int scmi_xfer_get_init(const struct scmi_handle *h, u8 msg_id, u8 prot_id,
 		       size_t tx_size, size_t rx_size, struct scmi_xfer **p);
 int scmi_handle_put(const struct scmi_handle *handle);
diff --git a/drivers/firmware/arm_scmi/driver.c b/drivers/firmware/arm_scmi/driver.c
index b5bc4c7a8fab..3eb0382491ce 100644
--- a/drivers/firmware/arm_scmi/driver.c
+++ b/drivers/firmware/arm_scmi/driver.c
@@ -30,8 +30,14 @@
 #include "common.h"
 
 #define MSG_ID_MASK		GENMASK(7, 0)
+#define MSG_XTRACT_ID(hdr)	FIELD_GET(MSG_ID_MASK, (hdr))
 #define MSG_TYPE_MASK		GENMASK(9, 8)
+#define MSG_XTRACT_TYPE(hdr)	FIELD_GET(MSG_TYPE_MASK, (hdr))
+#define MSG_TYPE_COMMAND	0
+#define MSG_TYPE_DELAYED_RESP	2
+#define MSG_TYPE_NOTIFICATION	3
 #define MSG_PROTOCOL_ID_MASK	GENMASK(17, 10)
+#define MSG_XTRACT_PROT_ID(hdr)	FIELD_GET(MSG_PROTOCOL_ID_MASK, (hdr))
 #define MSG_TOKEN_ID_MASK	GENMASK(27, 18)
 #define MSG_XTRACT_TOKEN(hdr)	FIELD_GET(MSG_TOKEN_ID_MASK, (hdr))
 #define MSG_TOKEN_MAX		(MSG_XTRACT_TOKEN(MSG_TOKEN_ID_MASK) + 1)
@@ -86,7 +92,7 @@ struct scmi_desc {
 };
 
 /**
- * struct scmi_chan_info - Structure representing a SCMI channel informfation
+ * struct scmi_chan_info - Structure representing a SCMI channel information
  *
  * @cl: Mailbox Client
  * @chan: Transmit/Receive mailbox channel
@@ -111,8 +117,9 @@ struct scmi_chan_info {
  * @handle: Instance of SCMI handle to send to clients
  * @version: SCMI revision information containing protocol version,
  *	implementation version and (sub-)vendor identification.
- * @minfo: Message info
- * @tx_idr: IDR object to map protocol id to channel info pointer
+ * @tx_minfo: Universal Transmit Message management info
+ * @tx_idr: IDR object to map protocol id to Tx channel info pointer
+ * @rx_idr: IDR object to map protocol id to Rx channel info pointer
  * @protocols_imp: List of protocols implemented, currently maximum of
  *	MAX_PROTOCOLS_IMP elements allocated by the base protocol
  * @node: List head
@@ -123,8 +130,9 @@ struct scmi_info {
 	const struct scmi_desc *desc;
 	struct scmi_revision_info version;
 	struct scmi_handle handle;
-	struct scmi_xfers_info minfo;
+	struct scmi_xfers_info tx_minfo;
 	struct idr tx_idr;
+	struct idr rx_idr;
 	u8 *protocols_imp;
 	struct list_head node;
 	int users;
@@ -182,7 +190,7 @@ static inline int scmi_to_linux_errno(int errno)
 static inline void scmi_dump_header_dbg(struct device *dev,
 					struct scmi_msg_hdr *hdr)
 {
-	dev_dbg(dev, "Command ID: %x Sequence ID: %x Protocol: %x\n",
+	dev_dbg(dev, "Message ID: %x Sequence ID: %x Protocol: %x\n",
 		hdr->id, hdr->seq, hdr->protocol_id);
 }
 
@@ -190,7 +198,7 @@ static void scmi_fetch_response(struct scmi_xfer *xfer,
 				struct scmi_shared_mem __iomem *mem)
 {
 	xfer->hdr.status = ioread32(mem->msg_payload);
-	/* Skip the length of header and statues in payload area i.e 8 bytes*/
+	/* Skip the length of header and status in payload area i.e 8 bytes */
 	xfer->rx.len = min_t(size_t, xfer->rx.len, ioread32(&mem->length) - 8);
 
 	/* Take a copy to the rx buffer.. */
@@ -198,56 +206,12 @@ static void scmi_fetch_response(struct scmi_xfer *xfer,
 }
 
 /**
- * scmi_rx_callback() - mailbox client callback for receive messages
- *
- * @cl: client pointer
- * @m: mailbox message
- *
- * Processes one received message to appropriate transfer information and
- * signals completion of the transfer.
- *
- * NOTE: This function will be invoked in IRQ context, hence should be
- * as optimal as possible.
- */
-static void scmi_rx_callback(struct mbox_client *cl, void *m)
-{
-	u16 xfer_id;
-	struct scmi_xfer *xfer;
-	struct scmi_chan_info *cinfo = client_to_scmi_chan_info(cl);
-	struct device *dev = cinfo->dev;
-	struct scmi_info *info = handle_to_scmi_info(cinfo->handle);
-	struct scmi_xfers_info *minfo = &info->minfo;
-	struct scmi_shared_mem __iomem *mem = cinfo->payload;
-
-	xfer_id = MSG_XTRACT_TOKEN(ioread32(&mem->msg_header));
-
-	/* Are we even expecting this? */
-	if (!test_bit(xfer_id, minfo->xfer_alloc_table)) {
-		dev_err(dev, "message for %d is not expected!\n", xfer_id);
-		return;
-	}
-
-	xfer = &minfo->xfer_block[xfer_id];
-
-	scmi_dump_header_dbg(dev, &xfer->hdr);
-	/* Is the message of valid length? */
-	if (xfer->rx.len > info->desc->max_msg_size) {
-		dev_err(dev, "unable to handle %zu xfer(max %d)\n",
-			xfer->rx.len, info->desc->max_msg_size);
-		return;
-	}
-
-	scmi_fetch_response(xfer, mem);
-	complete(&xfer->done);
-}
-
-/**
  * pack_scmi_header() - packs and returns 32-bit header
  *
  * @hdr: pointer to header containing all the information on message id,
  *	protocol id and sequence id.
  *
- * Return: 32-bit packed command header to be sent to the platform.
+ * Return: 32-bit packed message header to be sent to the platform.
  */
 static inline u32 pack_scmi_header(struct scmi_msg_hdr *hdr)
 {
@@ -257,6 +221,18 @@ static inline u32 pack_scmi_header(struct scmi_msg_hdr *hdr)
 }
 
 /**
+ * unpack_scmi_header() - unpacks and records message and protocol id
+ *
+ * @msg_hdr: 32-bit packed message header sent from the platform
+ * @hdr: pointer to header to fetch message and protocol id.
+ */
+static inline void unpack_scmi_header(u32 msg_hdr, struct scmi_msg_hdr *hdr)
+{
+	hdr->id = MSG_XTRACT_ID(msg_hdr);
+	hdr->protocol_id = MSG_XTRACT_PROT_ID(msg_hdr);
+}
+
+/**
  * scmi_tx_prepare() - mailbox client callback to prepare for the transfer
  *
  * @cl: client pointer
@@ -271,6 +247,14 @@ static void scmi_tx_prepare(struct mbox_client *cl, void *m)
 	struct scmi_chan_info *cinfo = client_to_scmi_chan_info(cl);
 	struct scmi_shared_mem __iomem *mem = cinfo->payload;
 
+	/*
+	 * Ideally channel must be free by now unless OS timeout last
+	 * request and platform continued to process the same, wait
+	 * until it releases the shared memory, otherwise we may endup
+	 * overwriting its response with new message payload or vice-versa
+	 */
+	spin_until_cond(ioread32(&mem->channel_status) &
+			SCMI_SHMEM_CHAN_STAT_CHANNEL_FREE);
 	/* Mark channel busy + clear error */
 	iowrite32(0x0, &mem->channel_status);
 	iowrite32(t->hdr.poll_completion ? 0 : SCMI_SHMEM_FLAG_INTR_ENABLED,
@@ -285,8 +269,9 @@ static void scmi_tx_prepare(struct mbox_client *cl, void *m)
  * scmi_xfer_get() - Allocate one message
  *
  * @handle: Pointer to SCMI entity handle
+ * @minfo: Pointer to Tx/Rx Message management info based on channel type
  *
- * Helper function which is used by various command functions that are
+ * Helper function which is used by various message functions that are
  * exposed to clients of this driver for allocating a message traffic event.
  *
  * This function can sleep depending on pending requests already in the system
@@ -295,13 +280,13 @@ static void scmi_tx_prepare(struct mbox_client *cl, void *m)
  *
  * Return: 0 if all went fine, else corresponding error.
  */
-static struct scmi_xfer *scmi_xfer_get(const struct scmi_handle *handle)
+static struct scmi_xfer *scmi_xfer_get(const struct scmi_handle *handle,
+				       struct scmi_xfers_info *minfo)
 {
 	u16 xfer_id;
 	struct scmi_xfer *xfer;
 	unsigned long flags, bit_pos;
 	struct scmi_info *info = handle_to_scmi_info(handle);
-	struct scmi_xfers_info *minfo = &info->minfo;
 
 	/* Keep the locked section as small as possible */
 	spin_lock_irqsave(&minfo->xfer_lock, flags);
@@ -324,18 +309,17 @@ static struct scmi_xfer *scmi_xfer_get(const struct scmi_handle *handle)
 }
 
 /**
- * scmi_xfer_put() - Release a message
+ * __scmi_xfer_put() - Release a message
  *
- * @handle: Pointer to SCMI entity handle
+ * @minfo: Pointer to Tx/Rx Message management info based on channel type
  * @xfer: message that was reserved by scmi_xfer_get
  *
  * This holds a spinlock to maintain integrity of internal data structures.
  */
-void scmi_xfer_put(const struct scmi_handle *handle, struct scmi_xfer *xfer)
+static void
+__scmi_xfer_put(struct scmi_xfers_info *minfo, struct scmi_xfer *xfer)
 {
 	unsigned long flags;
-	struct scmi_info *info = handle_to_scmi_info(handle);
-	struct scmi_xfers_info *minfo = &info->minfo;
 
 	/*
 	 * Keep the locked section as small as possible
@@ -347,6 +331,68 @@ void scmi_xfer_put(const struct scmi_handle *handle, struct scmi_xfer *xfer)
 	spin_unlock_irqrestore(&minfo->xfer_lock, flags);
 }
 
+/**
+ * scmi_rx_callback() - mailbox client callback for receive messages
+ *
+ * @cl: client pointer
+ * @m: mailbox message
+ *
+ * Processes one received message to appropriate transfer information and
+ * signals completion of the transfer.
+ *
+ * NOTE: This function will be invoked in IRQ context, hence should be
+ * as optimal as possible.
+ */
+static void scmi_rx_callback(struct mbox_client *cl, void *m)
+{
+	u8 msg_type;
+	u32 msg_hdr;
+	u16 xfer_id;
+	struct scmi_xfer *xfer;
+	struct scmi_chan_info *cinfo = client_to_scmi_chan_info(cl);
+	struct device *dev = cinfo->dev;
+	struct scmi_info *info = handle_to_scmi_info(cinfo->handle);
+	struct scmi_xfers_info *minfo = &info->tx_minfo;
+	struct scmi_shared_mem __iomem *mem = cinfo->payload;
+
+	msg_hdr = ioread32(&mem->msg_header);
+	msg_type = MSG_XTRACT_TYPE(msg_hdr);
+	xfer_id = MSG_XTRACT_TOKEN(msg_hdr);
+
+	if (msg_type == MSG_TYPE_NOTIFICATION)
+		return; /* Notifications not yet supported */
+
+	/* Are we even expecting this? */
+	if (!test_bit(xfer_id, minfo->xfer_alloc_table)) {
+		dev_err(dev, "message for %d is not expected!\n", xfer_id);
+		return;
+	}
+
+	xfer = &minfo->xfer_block[xfer_id];
+
+	scmi_dump_header_dbg(dev, &xfer->hdr);
+
+	scmi_fetch_response(xfer, mem);
+
+	if (msg_type == MSG_TYPE_DELAYED_RESP)
+		complete(xfer->async_done);
+	else
+		complete(&xfer->done);
+}
+
+/**
+ * scmi_xfer_put() - Release a transmit message
+ *
+ * @handle: Pointer to SCMI entity handle
+ * @xfer: message that was reserved by scmi_xfer_get
+ */
+void scmi_xfer_put(const struct scmi_handle *handle, struct scmi_xfer *xfer)
+{
+	struct scmi_info *info = handle_to_scmi_info(handle);
+
+	__scmi_xfer_put(&info->tx_minfo, xfer);
+}
+
 static bool
 scmi_xfer_poll_done(const struct scmi_chan_info *cinfo, struct scmi_xfer *xfer)
 {
@@ -435,8 +481,36 @@ int scmi_do_xfer(const struct scmi_handle *handle, struct scmi_xfer *xfer)
 	return ret;
 }
 
+#define SCMI_MAX_RESPONSE_TIMEOUT	(2 * MSEC_PER_SEC)
+
+/**
+ * scmi_do_xfer_with_response() - Do one transfer and wait until the delayed
+ *	response is received
+ *
+ * @handle: Pointer to SCMI entity handle
+ * @xfer: Transfer to initiate and wait for response
+ *
+ * Return: -ETIMEDOUT in case of no delayed response, if transmit error,
+ *	return corresponding error, else if all goes well, return 0.
+ */
+int scmi_do_xfer_with_response(const struct scmi_handle *handle,
+			       struct scmi_xfer *xfer)
+{
+	int ret, timeout = msecs_to_jiffies(SCMI_MAX_RESPONSE_TIMEOUT);
+	DECLARE_COMPLETION_ONSTACK(async_response);
+
+	xfer->async_done = &async_response;
+
+	ret = scmi_do_xfer(handle, xfer);
+	if (!ret && !wait_for_completion_timeout(xfer->async_done, timeout))
+		ret = -ETIMEDOUT;
+
+	xfer->async_done = NULL;
+	return ret;
+}
+
 /**
- * scmi_xfer_get_init() - Allocate and initialise one message
+ * scmi_xfer_get_init() - Allocate and initialise one message for transmit
  *
  * @handle: Pointer to SCMI entity handle
  * @msg_id: Message identifier
@@ -457,6 +531,7 @@ int scmi_xfer_get_init(const struct scmi_handle *handle, u8 msg_id, u8 prot_id,
 	int ret;
 	struct scmi_xfer *xfer;
 	struct scmi_info *info = handle_to_scmi_info(handle);
+	struct scmi_xfers_info *minfo = &info->tx_minfo;
 	struct device *dev = info->dev;
 
 	/* Ensure we have sane transfer sizes */
@@ -464,7 +539,7 @@ int scmi_xfer_get_init(const struct scmi_handle *handle, u8 msg_id, u8 prot_id,
 	    tx_size > info->desc->max_msg_size)
 		return -ERANGE;
 
-	xfer = scmi_xfer_get(handle);
+	xfer = scmi_xfer_get(handle, minfo);
 	if (IS_ERR(xfer)) {
 		ret = PTR_ERR(xfer);
 		dev_err(dev, "failed to get free message slot(%d)\n", ret);
@@ -597,27 +672,13 @@ int scmi_handle_put(const struct scmi_handle *handle)
 	return 0;
 }
 
-static const struct scmi_desc scmi_generic_desc = {
-	.max_rx_timeout_ms = 30,	/* We may increase this if required */
-	.max_msg = 20,		/* Limited by MBOX_TX_QUEUE_LEN */
-	.max_msg_size = 128,
-};
-
-/* Each compatible listed below must have descriptor associated with it */
-static const struct of_device_id scmi_of_match[] = {
-	{ .compatible = "arm,scmi", .data = &scmi_generic_desc },
-	{ /* Sentinel */ },
-};
-
-MODULE_DEVICE_TABLE(of, scmi_of_match);
-
 static int scmi_xfer_info_init(struct scmi_info *sinfo)
 {
 	int i;
 	struct scmi_xfer *xfer;
 	struct device *dev = sinfo->dev;
 	const struct scmi_desc *desc = sinfo->desc;
-	struct scmi_xfers_info *info = &sinfo->minfo;
+	struct scmi_xfers_info *info = &sinfo->tx_minfo;
 
 	/* Pre-allocated messages, no more than what hdr.seq can support */
 	if (WARN_ON(desc->max_msg >= MSG_TOKEN_MAX)) {
@@ -652,61 +713,32 @@ static int scmi_xfer_info_init(struct scmi_info *sinfo)
 	return 0;
 }
 
-static int scmi_mailbox_check(struct device_node *np)
+static int scmi_mailbox_check(struct device_node *np, int idx)
 {
-	return of_parse_phandle_with_args(np, "mboxes", "#mbox-cells", 0, NULL);
+	return of_parse_phandle_with_args(np, "mboxes", "#mbox-cells",
+					  idx, NULL);
 }
 
-static int scmi_mbox_free_channel(int id, void *p, void *data)
+static int scmi_mbox_chan_setup(struct scmi_info *info, struct device *dev,
+				int prot_id, bool tx)
 {
-	struct scmi_chan_info *cinfo = p;
-	struct idr *idr = data;
-
-	if (!IS_ERR_OR_NULL(cinfo->chan)) {
-		mbox_free_channel(cinfo->chan);
-		cinfo->chan = NULL;
-	}
-
-	idr_remove(idr, id);
-
-	return 0;
-}
-
-static int scmi_remove(struct platform_device *pdev)
-{
-	int ret = 0;
-	struct scmi_info *info = platform_get_drvdata(pdev);
-	struct idr *idr = &info->tx_idr;
-
-	mutex_lock(&scmi_list_mutex);
-	if (info->users)
-		ret = -EBUSY;
-	else
-		list_del(&info->node);
-	mutex_unlock(&scmi_list_mutex);
-
-	if (ret)
-		return ret;
-
-	/* Safe to free channels since no more users */
-	ret = idr_for_each(idr, scmi_mbox_free_channel, idr);
-	idr_destroy(&info->tx_idr);
-
-	return ret;
-}
-
-static inline int
-scmi_mbox_chan_setup(struct scmi_info *info, struct device *dev, int prot_id)
-{
-	int ret;
+	int ret, idx;
 	struct resource res;
 	resource_size_t size;
 	struct device_node *shmem, *np = dev->of_node;
 	struct scmi_chan_info *cinfo;
 	struct mbox_client *cl;
+	struct idr *idr;
+	const char *desc = tx ? "Tx" : "Rx";
 
-	if (scmi_mailbox_check(np)) {
-		cinfo = idr_find(&info->tx_idr, SCMI_PROTOCOL_BASE);
+	/* Transmit channel is first entry i.e. index 0 */
+	idx = tx ? 0 : 1;
+	idr = tx ? &info->tx_idr : &info->rx_idr;
+
+	if (scmi_mailbox_check(np, idx)) {
+		cinfo = idr_find(idr, SCMI_PROTOCOL_BASE);
+		if (unlikely(!cinfo)) /* Possible only if platform has no Rx */
+			return -EINVAL;
 		goto idr_alloc;
 	}
 
@@ -719,36 +751,36 @@ scmi_mbox_chan_setup(struct scmi_info *info, struct device *dev, int prot_id)
 	cl = &cinfo->cl;
 	cl->dev = dev;
 	cl->rx_callback = scmi_rx_callback;
-	cl->tx_prepare = scmi_tx_prepare;
+	cl->tx_prepare = tx ? scmi_tx_prepare : NULL;
 	cl->tx_block = false;
-	cl->knows_txdone = true;
+	cl->knows_txdone = tx;
 
-	shmem = of_parse_phandle(np, "shmem", 0);
+	shmem = of_parse_phandle(np, "shmem", idx);
 	ret = of_address_to_resource(shmem, 0, &res);
 	of_node_put(shmem);
 	if (ret) {
-		dev_err(dev, "failed to get SCMI Tx payload mem resource\n");
+		dev_err(dev, "failed to get SCMI %s payload memory\n", desc);
 		return ret;
 	}
 
 	size = resource_size(&res);
 	cinfo->payload = devm_ioremap(info->dev, res.start, size);
 	if (!cinfo->payload) {
-		dev_err(dev, "failed to ioremap SCMI Tx payload\n");
+		dev_err(dev, "failed to ioremap SCMI %s payload\n", desc);
 		return -EADDRNOTAVAIL;
 	}
 
-	/* Transmit channel is first entry i.e. index 0 */
-	cinfo->chan = mbox_request_channel(cl, 0);
+	cinfo->chan = mbox_request_channel(cl, idx);
 	if (IS_ERR(cinfo->chan)) {
 		ret = PTR_ERR(cinfo->chan);
 		if (ret != -EPROBE_DEFER)
-			dev_err(dev, "failed to request SCMI Tx mailbox\n");
+			dev_err(dev, "failed to request SCMI %s mailbox\n",
+				desc);
 		return ret;
 	}
 
 idr_alloc:
-	ret = idr_alloc(&info->tx_idr, cinfo, prot_id, prot_id + 1, GFP_KERNEL);
+	ret = idr_alloc(idr, cinfo, prot_id, prot_id + 1, GFP_KERNEL);
 	if (ret != prot_id) {
 		dev_err(dev, "unable to allocate SCMI idr slot err %d\n", ret);
 		return ret;
@@ -758,6 +790,17 @@ idr_alloc:
 	return 0;
 }
 
+static inline int
+scmi_mbox_txrx_setup(struct scmi_info *info, struct device *dev, int prot_id)
+{
+	int ret = scmi_mbox_chan_setup(info, dev, prot_id, true);
+
+	if (!ret) /* Rx is optional, hence no error check */
+		scmi_mbox_chan_setup(info, dev, prot_id, false);
+
+	return ret;
+}
+
 static inline void
 scmi_create_protocol_device(struct device_node *np, struct scmi_info *info,
 			    int prot_id)
@@ -771,7 +814,7 @@ scmi_create_protocol_device(struct device_node *np, struct scmi_info *info,
 		return;
 	}
 
-	if (scmi_mbox_chan_setup(info, &sdev->dev, prot_id)) {
+	if (scmi_mbox_txrx_setup(info, &sdev->dev, prot_id)) {
 		dev_err(&sdev->dev, "failed to setup transport\n");
 		scmi_device_destroy(sdev);
 		return;
@@ -791,7 +834,7 @@ static int scmi_probe(struct platform_device *pdev)
 	struct device_node *child, *np = dev->of_node;
 
 	/* Only mailbox method supported, check for the presence of one */
-	if (scmi_mailbox_check(np)) {
+	if (scmi_mailbox_check(np, 0)) {
 		dev_err(dev, "no mailbox found in %pOF\n", np);
 		return -EINVAL;
 	}
@@ -814,12 +857,13 @@ static int scmi_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, info);
 	idr_init(&info->tx_idr);
+	idr_init(&info->rx_idr);
 
 	handle = &info->handle;
 	handle->dev = info->dev;
 	handle->version = &info->version;
 
-	ret = scmi_mbox_chan_setup(info, dev, SCMI_PROTOCOL_BASE);
+	ret = scmi_mbox_txrx_setup(info, dev, SCMI_PROTOCOL_BASE);
 	if (ret)
 		return ret;
 
@@ -854,6 +898,62 @@ static int scmi_probe(struct platform_device *pdev)
 	return 0;
 }
 
+static int scmi_mbox_free_channel(int id, void *p, void *data)
+{
+	struct scmi_chan_info *cinfo = p;
+	struct idr *idr = data;
+
+	if (!IS_ERR_OR_NULL(cinfo->chan)) {
+		mbox_free_channel(cinfo->chan);
+		cinfo->chan = NULL;
+	}
+
+	idr_remove(idr, id);
+
+	return 0;
+}
+
+static int scmi_remove(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct scmi_info *info = platform_get_drvdata(pdev);
+	struct idr *idr = &info->tx_idr;
+
+	mutex_lock(&scmi_list_mutex);
+	if (info->users)
+		ret = -EBUSY;
+	else
+		list_del(&info->node);
+	mutex_unlock(&scmi_list_mutex);
+
+	if (ret)
+		return ret;
+
+	/* Safe to free channels since no more users */
+	ret = idr_for_each(idr, scmi_mbox_free_channel, idr);
+	idr_destroy(&info->tx_idr);
+
+	idr = &info->rx_idr;
+	ret = idr_for_each(idr, scmi_mbox_free_channel, idr);
+	idr_destroy(&info->rx_idr);
+
+	return ret;
+}
+
+static const struct scmi_desc scmi_generic_desc = {
+	.max_rx_timeout_ms = 30,	/* We may increase this if required */
+	.max_msg = 20,		/* Limited by MBOX_TX_QUEUE_LEN */
+	.max_msg_size = 128,
+};
+
+/* Each compatible listed below must have descriptor associated with it */
+static const struct of_device_id scmi_of_match[] = {
+	{ .compatible = "arm,scmi", .data = &scmi_generic_desc },
+	{ /* Sentinel */ },
+};
+
+MODULE_DEVICE_TABLE(of, scmi_of_match);
+
 static struct platform_driver scmi_driver = {
 	.driver = {
 		   .name = "arm-scmi",
diff --git a/drivers/firmware/arm_scmi/perf.c b/drivers/firmware/arm_scmi/perf.c
index 3c8ae7cc35de..4a8012e3cb8c 100644
--- a/drivers/firmware/arm_scmi/perf.c
+++ b/drivers/firmware/arm_scmi/perf.c
@@ -5,7 +5,10 @@
  * Copyright (C) 2018 ARM Ltd.
  */
 
+#include <linux/bits.h>
 #include <linux/of.h>
+#include <linux/io.h>
+#include <linux/io-64-nonatomic-hi-lo.h>
 #include <linux/platform_device.h>
 #include <linux/pm_opp.h>
 #include <linux/sort.h>
@@ -21,6 +24,7 @@ enum scmi_performance_protocol_cmd {
 	PERF_LEVEL_GET = 0x8,
 	PERF_NOTIFY_LIMITS = 0x9,
 	PERF_NOTIFY_LEVEL = 0xa,
+	PERF_DESCRIBE_FASTCHANNEL = 0xb,
 };
 
 struct scmi_opp {
@@ -44,6 +48,7 @@ struct scmi_msg_resp_perf_domain_attributes {
 #define SUPPORTS_SET_PERF_LVL(x)	((x) & BIT(30))
 #define SUPPORTS_PERF_LIMIT_NOTIFY(x)	((x) & BIT(29))
 #define SUPPORTS_PERF_LEVEL_NOTIFY(x)	((x) & BIT(28))
+#define SUPPORTS_PERF_FASTCHANNELS(x)	((x) & BIT(27))
 	__le32 rate_limit_us;
 	__le32 sustained_freq_khz;
 	__le32 sustained_perf_level;
@@ -87,17 +92,56 @@ struct scmi_msg_resp_perf_describe_levels {
 	} opp[0];
 };
 
+struct scmi_perf_get_fc_info {
+	__le32 domain;
+	__le32 message_id;
+};
+
+struct scmi_msg_resp_perf_desc_fc {
+	__le32 attr;
+#define SUPPORTS_DOORBELL(x)		((x) & BIT(0))
+#define DOORBELL_REG_WIDTH(x)		FIELD_GET(GENMASK(2, 1), (x))
+	__le32 rate_limit;
+	__le32 chan_addr_low;
+	__le32 chan_addr_high;
+	__le32 chan_size;
+	__le32 db_addr_low;
+	__le32 db_addr_high;
+	__le32 db_set_lmask;
+	__le32 db_set_hmask;
+	__le32 db_preserve_lmask;
+	__le32 db_preserve_hmask;
+};
+
+struct scmi_fc_db_info {
+	int width;
+	u64 set;
+	u64 mask;
+	void __iomem *addr;
+};
+
+struct scmi_fc_info {
+	void __iomem *level_set_addr;
+	void __iomem *limit_set_addr;
+	void __iomem *level_get_addr;
+	void __iomem *limit_get_addr;
+	struct scmi_fc_db_info *level_set_db;
+	struct scmi_fc_db_info *limit_set_db;
+};
+
 struct perf_dom_info {
 	bool set_limits;
 	bool set_perf;
 	bool perf_limit_notify;
 	bool perf_level_notify;
+	bool perf_fastchannels;
 	u32 opp_count;
 	u32 sustained_freq_khz;
 	u32 sustained_perf_level;
 	u32 mult_factor;
 	char name[SCMI_MAX_STR_SIZE];
 	struct scmi_opp opp[MAX_OPPS];
+	struct scmi_fc_info *fc_info;
 };
 
 struct scmi_perf_info {
@@ -151,7 +195,7 @@ scmi_perf_domain_attributes_get(const struct scmi_handle *handle, u32 domain,
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(domain);
+	put_unaligned_le32(domain, t->tx.buf);
 	attr = t->rx.buf;
 
 	ret = scmi_do_xfer(handle, t);
@@ -162,6 +206,7 @@ scmi_perf_domain_attributes_get(const struct scmi_handle *handle, u32 domain,
 		dom_info->set_perf = SUPPORTS_SET_PERF_LVL(flags);
 		dom_info->perf_limit_notify = SUPPORTS_PERF_LIMIT_NOTIFY(flags);
 		dom_info->perf_level_notify = SUPPORTS_PERF_LEVEL_NOTIFY(flags);
+		dom_info->perf_fastchannels = SUPPORTS_PERF_FASTCHANNELS(flags);
 		dom_info->sustained_freq_khz =
 					le32_to_cpu(attr->sustained_freq_khz);
 		dom_info->sustained_perf_level =
@@ -249,8 +294,42 @@ scmi_perf_describe_levels_get(const struct scmi_handle *handle, u32 domain,
 	return ret;
 }
 
-static int scmi_perf_limits_set(const struct scmi_handle *handle, u32 domain,
-				u32 max_perf, u32 min_perf)
+#define SCMI_PERF_FC_RING_DB(w)				\
+do {							\
+	u##w val = 0;					\
+							\
+	if (db->mask)					\
+		val = ioread##w(db->addr) & db->mask;	\
+	iowrite##w((u##w)db->set | val, db->addr);	\
+} while (0)
+
+static void scmi_perf_fc_ring_db(struct scmi_fc_db_info *db)
+{
+	if (!db || !db->addr)
+		return;
+
+	if (db->width == 1)
+		SCMI_PERF_FC_RING_DB(8);
+	else if (db->width == 2)
+		SCMI_PERF_FC_RING_DB(16);
+	else if (db->width == 4)
+		SCMI_PERF_FC_RING_DB(32);
+	else /* db->width == 8 */
+#ifdef CONFIG_64BIT
+		SCMI_PERF_FC_RING_DB(64);
+#else
+	{
+		u64 val = 0;
+
+		if (db->mask)
+			val = ioread64_hi_lo(db->addr) & db->mask;
+		iowrite64_hi_lo(db->set, db->addr);
+	}
+#endif
+}
+
+static int scmi_perf_mb_limits_set(const struct scmi_handle *handle, u32 domain,
+				   u32 max_perf, u32 min_perf)
 {
 	int ret;
 	struct scmi_xfer *t;
@@ -272,8 +351,24 @@ static int scmi_perf_limits_set(const struct scmi_handle *handle, u32 domain,
 	return ret;
 }
 
-static int scmi_perf_limits_get(const struct scmi_handle *handle, u32 domain,
-				u32 *max_perf, u32 *min_perf)
+static int scmi_perf_limits_set(const struct scmi_handle *handle, u32 domain,
+				u32 max_perf, u32 min_perf)
+{
+	struct scmi_perf_info *pi = handle->perf_priv;
+	struct perf_dom_info *dom = pi->dom_info + domain;
+
+	if (dom->fc_info && dom->fc_info->limit_set_addr) {
+		iowrite32(max_perf, dom->fc_info->limit_set_addr);
+		iowrite32(min_perf, dom->fc_info->limit_set_addr + 4);
+		scmi_perf_fc_ring_db(dom->fc_info->limit_set_db);
+		return 0;
+	}
+
+	return scmi_perf_mb_limits_set(handle, domain, max_perf, min_perf);
+}
+
+static int scmi_perf_mb_limits_get(const struct scmi_handle *handle, u32 domain,
+				   u32 *max_perf, u32 *min_perf)
 {
 	int ret;
 	struct scmi_xfer *t;
@@ -284,7 +379,7 @@ static int scmi_perf_limits_get(const struct scmi_handle *handle, u32 domain,
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(domain);
+	put_unaligned_le32(domain, t->tx.buf);
 
 	ret = scmi_do_xfer(handle, t);
 	if (!ret) {
@@ -298,8 +393,23 @@ static int scmi_perf_limits_get(const struct scmi_handle *handle, u32 domain,
 	return ret;
 }
 
-static int scmi_perf_level_set(const struct scmi_handle *handle, u32 domain,
-			       u32 level, bool poll)
+static int scmi_perf_limits_get(const struct scmi_handle *handle, u32 domain,
+				u32 *max_perf, u32 *min_perf)
+{
+	struct scmi_perf_info *pi = handle->perf_priv;
+	struct perf_dom_info *dom = pi->dom_info + domain;
+
+	if (dom->fc_info && dom->fc_info->limit_get_addr) {
+		*max_perf = ioread32(dom->fc_info->limit_get_addr);
+		*min_perf = ioread32(dom->fc_info->limit_get_addr + 4);
+		return 0;
+	}
+
+	return scmi_perf_mb_limits_get(handle, domain, max_perf, min_perf);
+}
+
+static int scmi_perf_mb_level_set(const struct scmi_handle *handle, u32 domain,
+				  u32 level, bool poll)
 {
 	int ret;
 	struct scmi_xfer *t;
@@ -321,8 +431,23 @@ static int scmi_perf_level_set(const struct scmi_handle *handle, u32 domain,
 	return ret;
 }
 
-static int scmi_perf_level_get(const struct scmi_handle *handle, u32 domain,
-			       u32 *level, bool poll)
+static int scmi_perf_level_set(const struct scmi_handle *handle, u32 domain,
+			       u32 level, bool poll)
+{
+	struct scmi_perf_info *pi = handle->perf_priv;
+	struct perf_dom_info *dom = pi->dom_info + domain;
+
+	if (dom->fc_info && dom->fc_info->level_set_addr) {
+		iowrite32(level, dom->fc_info->level_set_addr);
+		scmi_perf_fc_ring_db(dom->fc_info->level_set_db);
+		return 0;
+	}
+
+	return scmi_perf_mb_level_set(handle, domain, level, poll);
+}
+
+static int scmi_perf_mb_level_get(const struct scmi_handle *handle, u32 domain,
+				  u32 *level, bool poll)
 {
 	int ret;
 	struct scmi_xfer *t;
@@ -333,16 +458,128 @@ static int scmi_perf_level_get(const struct scmi_handle *handle, u32 domain,
 		return ret;
 
 	t->hdr.poll_completion = poll;
-	*(__le32 *)t->tx.buf = cpu_to_le32(domain);
+	put_unaligned_le32(domain, t->tx.buf);
 
 	ret = scmi_do_xfer(handle, t);
 	if (!ret)
-		*level = le32_to_cpu(*(__le32 *)t->rx.buf);
+		*level = get_unaligned_le32(t->rx.buf);
 
 	scmi_xfer_put(handle, t);
 	return ret;
 }
 
+static int scmi_perf_level_get(const struct scmi_handle *handle, u32 domain,
+			       u32 *level, bool poll)
+{
+	struct scmi_perf_info *pi = handle->perf_priv;
+	struct perf_dom_info *dom = pi->dom_info + domain;
+
+	if (dom->fc_info && dom->fc_info->level_get_addr) {
+		*level = ioread32(dom->fc_info->level_get_addr);
+		return 0;
+	}
+
+	return scmi_perf_mb_level_get(handle, domain, level, poll);
+}
+
+static bool scmi_perf_fc_size_is_valid(u32 msg, u32 size)
+{
+	if ((msg == PERF_LEVEL_GET || msg == PERF_LEVEL_SET) && size == 4)
+		return true;
+	if ((msg == PERF_LIMITS_GET || msg == PERF_LIMITS_SET) && size == 8)
+		return true;
+	return false;
+}
+
+static void
+scmi_perf_domain_desc_fc(const struct scmi_handle *handle, u32 domain,
+			 u32 message_id, void __iomem **p_addr,
+			 struct scmi_fc_db_info **p_db)
+{
+	int ret;
+	u32 flags;
+	u64 phys_addr;
+	u8 size;
+	void __iomem *addr;
+	struct scmi_xfer *t;
+	struct scmi_fc_db_info *db;
+	struct scmi_perf_get_fc_info *info;
+	struct scmi_msg_resp_perf_desc_fc *resp;
+
+	if (!p_addr)
+		return;
+
+	ret = scmi_xfer_get_init(handle, PERF_DESCRIBE_FASTCHANNEL,
+				 SCMI_PROTOCOL_PERF,
+				 sizeof(*info), sizeof(*resp), &t);
+	if (ret)
+		return;
+
+	info = t->tx.buf;
+	info->domain = cpu_to_le32(domain);
+	info->message_id = cpu_to_le32(message_id);
+
+	ret = scmi_do_xfer(handle, t);
+	if (ret)
+		goto err_xfer;
+
+	resp = t->rx.buf;
+	flags = le32_to_cpu(resp->attr);
+	size = le32_to_cpu(resp->chan_size);
+	if (!scmi_perf_fc_size_is_valid(message_id, size))
+		goto err_xfer;
+
+	phys_addr = le32_to_cpu(resp->chan_addr_low);
+	phys_addr |= (u64)le32_to_cpu(resp->chan_addr_high) << 32;
+	addr = devm_ioremap(handle->dev, phys_addr, size);
+	if (!addr)
+		goto err_xfer;
+	*p_addr = addr;
+
+	if (p_db && SUPPORTS_DOORBELL(flags)) {
+		db = devm_kzalloc(handle->dev, sizeof(*db), GFP_KERNEL);
+		if (!db)
+			goto err_xfer;
+
+		size = 1 << DOORBELL_REG_WIDTH(flags);
+		phys_addr = le32_to_cpu(resp->db_addr_low);
+		phys_addr |= (u64)le32_to_cpu(resp->db_addr_high) << 32;
+		addr = devm_ioremap(handle->dev, phys_addr, size);
+		if (!addr)
+			goto err_xfer;
+
+		db->addr = addr;
+		db->width = size;
+		db->set = le32_to_cpu(resp->db_set_lmask);
+		db->set |= (u64)le32_to_cpu(resp->db_set_hmask) << 32;
+		db->mask = le32_to_cpu(resp->db_preserve_lmask);
+		db->mask |= (u64)le32_to_cpu(resp->db_preserve_hmask) << 32;
+		*p_db = db;
+	}
+err_xfer:
+	scmi_xfer_put(handle, t);
+}
+
+static void scmi_perf_domain_init_fc(const struct scmi_handle *handle,
+				     u32 domain, struct scmi_fc_info **p_fc)
+{
+	struct scmi_fc_info *fc;
+
+	fc = devm_kzalloc(handle->dev, sizeof(*fc), GFP_KERNEL);
+	if (!fc)
+		return;
+
+	scmi_perf_domain_desc_fc(handle, domain, PERF_LEVEL_SET,
+				 &fc->level_set_addr, &fc->level_set_db);
+	scmi_perf_domain_desc_fc(handle, domain, PERF_LEVEL_GET,
+				 &fc->level_get_addr, NULL);
+	scmi_perf_domain_desc_fc(handle, domain, PERF_LIMITS_SET,
+				 &fc->limit_set_addr, &fc->limit_set_db);
+	scmi_perf_domain_desc_fc(handle, domain, PERF_LIMITS_GET,
+				 &fc->limit_get_addr, NULL);
+	*p_fc = fc;
+}
+
 /* Device specific ops */
 static int scmi_dev_domain_id(struct device *dev)
 {
@@ -494,6 +731,9 @@ static int scmi_perf_protocol_init(struct scmi_handle *handle)
 
 		scmi_perf_domain_attributes_get(handle, domain, dom);
 		scmi_perf_describe_levels_get(handle, domain, dom);
+
+		if (dom->perf_fastchannels)
+			scmi_perf_domain_init_fc(handle, domain, &dom->fc_info);
 	}
 
 	handle->perf_ops = &perf_ops;
diff --git a/drivers/firmware/arm_scmi/power.c b/drivers/firmware/arm_scmi/power.c
index 62f3401a1f01..5abef7079c0a 100644
--- a/drivers/firmware/arm_scmi/power.c
+++ b/drivers/firmware/arm_scmi/power.c
@@ -96,7 +96,7 @@ scmi_power_domain_attributes_get(const struct scmi_handle *handle, u32 domain,
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(domain);
+	put_unaligned_le32(domain, t->tx.buf);
 	attr = t->rx.buf;
 
 	ret = scmi_do_xfer(handle, t);
@@ -147,11 +147,11 @@ scmi_power_state_get(const struct scmi_handle *handle, u32 domain, u32 *state)
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(domain);
+	put_unaligned_le32(domain, t->tx.buf);
 
 	ret = scmi_do_xfer(handle, t);
 	if (!ret)
-		*state = le32_to_cpu(*(__le32 *)t->rx.buf);
+		*state = get_unaligned_le32(t->rx.buf);
 
 	scmi_xfer_put(handle, t);
 	return ret;
diff --git a/drivers/firmware/arm_scmi/reset.c b/drivers/firmware/arm_scmi/reset.c
new file mode 100644
index 000000000000..64cc81915581
--- /dev/null
+++ b/drivers/firmware/arm_scmi/reset.c
@@ -0,0 +1,231 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * System Control and Management Interface (SCMI) Reset Protocol
+ *
+ * Copyright (C) 2019 ARM Ltd.
+ */
+
+#include "common.h"
+
+enum scmi_reset_protocol_cmd {
+	RESET_DOMAIN_ATTRIBUTES = 0x3,
+	RESET = 0x4,
+	RESET_NOTIFY = 0x5,
+};
+
+enum scmi_reset_protocol_notify {
+	RESET_ISSUED = 0x0,
+};
+
+#define NUM_RESET_DOMAIN_MASK	0xffff
+#define RESET_NOTIFY_ENABLE	BIT(0)
+
+struct scmi_msg_resp_reset_domain_attributes {
+	__le32 attributes;
+#define SUPPORTS_ASYNC_RESET(x)		((x) & BIT(31))
+#define SUPPORTS_NOTIFY_RESET(x)	((x) & BIT(30))
+	__le32 latency;
+	    u8 name[SCMI_MAX_STR_SIZE];
+};
+
+struct scmi_msg_reset_domain_reset {
+	__le32 domain_id;
+	__le32 flags;
+#define AUTONOMOUS_RESET	BIT(0)
+#define EXPLICIT_RESET_ASSERT	BIT(1)
+#define ASYNCHRONOUS_RESET	BIT(2)
+	__le32 reset_state;
+#define ARCH_RESET_TYPE		BIT(31)
+#define COLD_RESET_STATE	BIT(0)
+#define ARCH_COLD_RESET		(ARCH_RESET_TYPE | COLD_RESET_STATE)
+};
+
+struct reset_dom_info {
+	bool async_reset;
+	bool reset_notify;
+	u32 latency_us;
+	char name[SCMI_MAX_STR_SIZE];
+};
+
+struct scmi_reset_info {
+	int num_domains;
+	struct reset_dom_info *dom_info;
+};
+
+static int scmi_reset_attributes_get(const struct scmi_handle *handle,
+				     struct scmi_reset_info *pi)
+{
+	int ret;
+	struct scmi_xfer *t;
+	u32 attr;
+
+	ret = scmi_xfer_get_init(handle, PROTOCOL_ATTRIBUTES,
+				 SCMI_PROTOCOL_RESET, 0, sizeof(attr), &t);
+	if (ret)
+		return ret;
+
+	ret = scmi_do_xfer(handle, t);
+	if (!ret) {
+		attr = get_unaligned_le32(t->rx.buf);
+		pi->num_domains = attr & NUM_RESET_DOMAIN_MASK;
+	}
+
+	scmi_xfer_put(handle, t);
+	return ret;
+}
+
+static int
+scmi_reset_domain_attributes_get(const struct scmi_handle *handle, u32 domain,
+				 struct reset_dom_info *dom_info)
+{
+	int ret;
+	struct scmi_xfer *t;
+	struct scmi_msg_resp_reset_domain_attributes *attr;
+
+	ret = scmi_xfer_get_init(handle, RESET_DOMAIN_ATTRIBUTES,
+				 SCMI_PROTOCOL_RESET, sizeof(domain),
+				 sizeof(*attr), &t);
+	if (ret)
+		return ret;
+
+	put_unaligned_le32(domain, t->tx.buf);
+	attr = t->rx.buf;
+
+	ret = scmi_do_xfer(handle, t);
+	if (!ret) {
+		u32 attributes = le32_to_cpu(attr->attributes);
+
+		dom_info->async_reset = SUPPORTS_ASYNC_RESET(attributes);
+		dom_info->reset_notify = SUPPORTS_NOTIFY_RESET(attributes);
+		dom_info->latency_us = le32_to_cpu(attr->latency);
+		if (dom_info->latency_us == U32_MAX)
+			dom_info->latency_us = 0;
+		strlcpy(dom_info->name, attr->name, SCMI_MAX_STR_SIZE);
+	}
+
+	scmi_xfer_put(handle, t);
+	return ret;
+}
+
+static int scmi_reset_num_domains_get(const struct scmi_handle *handle)
+{
+	struct scmi_reset_info *pi = handle->reset_priv;
+
+	return pi->num_domains;
+}
+
+static char *scmi_reset_name_get(const struct scmi_handle *handle, u32 domain)
+{
+	struct scmi_reset_info *pi = handle->reset_priv;
+	struct reset_dom_info *dom = pi->dom_info + domain;
+
+	return dom->name;
+}
+
+static int scmi_reset_latency_get(const struct scmi_handle *handle, u32 domain)
+{
+	struct scmi_reset_info *pi = handle->reset_priv;
+	struct reset_dom_info *dom = pi->dom_info + domain;
+
+	return dom->latency_us;
+}
+
+static int scmi_domain_reset(const struct scmi_handle *handle, u32 domain,
+			     u32 flags, u32 state)
+{
+	int ret;
+	struct scmi_xfer *t;
+	struct scmi_msg_reset_domain_reset *dom;
+	struct scmi_reset_info *pi = handle->reset_priv;
+	struct reset_dom_info *rdom = pi->dom_info + domain;
+
+	if (rdom->async_reset)
+		flags |= ASYNCHRONOUS_RESET;
+
+	ret = scmi_xfer_get_init(handle, RESET, SCMI_PROTOCOL_RESET,
+				 sizeof(*dom), 0, &t);
+	if (ret)
+		return ret;
+
+	dom = t->tx.buf;
+	dom->domain_id = cpu_to_le32(domain);
+	dom->flags = cpu_to_le32(flags);
+	dom->domain_id = cpu_to_le32(state);
+
+	if (rdom->async_reset)
+		ret = scmi_do_xfer_with_response(handle, t);
+	else
+		ret = scmi_do_xfer(handle, t);
+
+	scmi_xfer_put(handle, t);
+	return ret;
+}
+
+static int scmi_reset_domain_reset(const struct scmi_handle *handle, u32 domain)
+{
+	return scmi_domain_reset(handle, domain, AUTONOMOUS_RESET,
+				 ARCH_COLD_RESET);
+}
+
+static int
+scmi_reset_domain_assert(const struct scmi_handle *handle, u32 domain)
+{
+	return scmi_domain_reset(handle, domain, EXPLICIT_RESET_ASSERT,
+				 ARCH_COLD_RESET);
+}
+
+static int
+scmi_reset_domain_deassert(const struct scmi_handle *handle, u32 domain)
+{
+	return scmi_domain_reset(handle, domain, 0, ARCH_COLD_RESET);
+}
+
+static struct scmi_reset_ops reset_ops = {
+	.num_domains_get = scmi_reset_num_domains_get,
+	.name_get = scmi_reset_name_get,
+	.latency_get = scmi_reset_latency_get,
+	.reset = scmi_reset_domain_reset,
+	.assert = scmi_reset_domain_assert,
+	.deassert = scmi_reset_domain_deassert,
+};
+
+static int scmi_reset_protocol_init(struct scmi_handle *handle)
+{
+	int domain;
+	u32 version;
+	struct scmi_reset_info *pinfo;
+
+	scmi_version_get(handle, SCMI_PROTOCOL_RESET, &version);
+
+	dev_dbg(handle->dev, "Reset Version %d.%d\n",
+		PROTOCOL_REV_MAJOR(version), PROTOCOL_REV_MINOR(version));
+
+	pinfo = devm_kzalloc(handle->dev, sizeof(*pinfo), GFP_KERNEL);
+	if (!pinfo)
+		return -ENOMEM;
+
+	scmi_reset_attributes_get(handle, pinfo);
+
+	pinfo->dom_info = devm_kcalloc(handle->dev, pinfo->num_domains,
+				       sizeof(*pinfo->dom_info), GFP_KERNEL);
+	if (!pinfo->dom_info)
+		return -ENOMEM;
+
+	for (domain = 0; domain < pinfo->num_domains; domain++) {
+		struct reset_dom_info *dom = pinfo->dom_info + domain;
+
+		scmi_reset_domain_attributes_get(handle, domain, dom);
+	}
+
+	handle->reset_ops = &reset_ops;
+	handle->reset_priv = pinfo;
+
+	return 0;
+}
+
+static int __init scmi_reset_init(void)
+{
+	return scmi_protocol_register(SCMI_PROTOCOL_RESET,
+				      &scmi_reset_protocol_init);
+}
+subsys_initcall(scmi_reset_init);
diff --git a/drivers/firmware/arm_scmi/sensors.c b/drivers/firmware/arm_scmi/sensors.c
index 0e94ab56f679..a400ea805fc2 100644
--- a/drivers/firmware/arm_scmi/sensors.c
+++ b/drivers/firmware/arm_scmi/sensors.c
@@ -9,8 +9,8 @@
 
 enum scmi_sensor_protocol_cmd {
 	SENSOR_DESCRIPTION_GET = 0x3,
-	SENSOR_CONFIG_SET = 0x4,
-	SENSOR_TRIP_POINT_SET = 0x5,
+	SENSOR_TRIP_POINT_NOTIFY = 0x4,
+	SENSOR_TRIP_POINT_CONFIG = 0x5,
 	SENSOR_READING_GET = 0x6,
 };
 
@@ -42,9 +42,10 @@ struct scmi_msg_resp_sensor_description {
 	} desc[0];
 };
 
-struct scmi_msg_set_sensor_config {
+struct scmi_msg_sensor_trip_point_notify {
 	__le32 id;
 	__le32 event_control;
+#define SENSOR_TP_NOTIFY_ALL	BIT(0)
 };
 
 struct scmi_msg_set_sensor_trip_point {
@@ -119,7 +120,7 @@ static int scmi_sensor_description_get(const struct scmi_handle *handle,
 
 	do {
 		/* Set the number of sensors to be skipped/already read */
-		*(__le32 *)t->tx.buf = cpu_to_le32(desc_index);
+		put_unaligned_le32(desc_index, t->tx.buf);
 
 		ret = scmi_do_xfer(handle, t);
 		if (ret)
@@ -135,9 +136,10 @@ static int scmi_sensor_description_get(const struct scmi_handle *handle,
 		}
 
 		for (cnt = 0; cnt < num_returned; cnt++) {
-			u32 attrh;
+			u32 attrh, attrl;
 			struct scmi_sensor_info *s;
 
+			attrl = le32_to_cpu(buf->desc[cnt].attributes_low);
 			attrh = le32_to_cpu(buf->desc[cnt].attributes_high);
 			s = &si->sensors[desc_index + cnt];
 			s->id = le32_to_cpu(buf->desc[cnt].id);
@@ -146,6 +148,8 @@ static int scmi_sensor_description_get(const struct scmi_handle *handle,
 			/* Sign extend to a full s8 */
 			if (s->scale & SENSOR_SCALE_SIGN)
 				s->scale |= SENSOR_SCALE_EXTEND;
+			s->async = SUPPORTS_ASYNC_READ(attrl);
+			s->num_trip_points = NUM_TRIP_POINTS(attrl);
 			strlcpy(s->name, buf->desc[cnt].name, SCMI_MAX_STR_SIZE);
 		}
 
@@ -160,15 +164,15 @@ static int scmi_sensor_description_get(const struct scmi_handle *handle,
 	return ret;
 }
 
-static int
-scmi_sensor_configuration_set(const struct scmi_handle *handle, u32 sensor_id)
+static int scmi_sensor_trip_point_notify(const struct scmi_handle *handle,
+					 u32 sensor_id, bool enable)
 {
 	int ret;
-	u32 evt_cntl = BIT(0);
+	u32 evt_cntl = enable ? SENSOR_TP_NOTIFY_ALL : 0;
 	struct scmi_xfer *t;
-	struct scmi_msg_set_sensor_config *cfg;
+	struct scmi_msg_sensor_trip_point_notify *cfg;
 
-	ret = scmi_xfer_get_init(handle, SENSOR_CONFIG_SET,
+	ret = scmi_xfer_get_init(handle, SENSOR_TRIP_POINT_NOTIFY,
 				 SCMI_PROTOCOL_SENSOR, sizeof(*cfg), 0, &t);
 	if (ret)
 		return ret;
@@ -183,15 +187,16 @@ scmi_sensor_configuration_set(const struct scmi_handle *handle, u32 sensor_id)
 	return ret;
 }
 
-static int scmi_sensor_trip_point_set(const struct scmi_handle *handle,
-				      u32 sensor_id, u8 trip_id, u64 trip_value)
+static int
+scmi_sensor_trip_point_config(const struct scmi_handle *handle, u32 sensor_id,
+			      u8 trip_id, u64 trip_value)
 {
 	int ret;
 	u32 evt_cntl = SENSOR_TP_BOTH;
 	struct scmi_xfer *t;
 	struct scmi_msg_set_sensor_trip_point *trip;
 
-	ret = scmi_xfer_get_init(handle, SENSOR_TRIP_POINT_SET,
+	ret = scmi_xfer_get_init(handle, SENSOR_TRIP_POINT_CONFIG,
 				 SCMI_PROTOCOL_SENSOR, sizeof(*trip), 0, &t);
 	if (ret)
 		return ret;
@@ -209,11 +214,13 @@ static int scmi_sensor_trip_point_set(const struct scmi_handle *handle,
 }
 
 static int scmi_sensor_reading_get(const struct scmi_handle *handle,
-				   u32 sensor_id, bool async, u64 *value)
+				   u32 sensor_id, u64 *value)
 {
 	int ret;
 	struct scmi_xfer *t;
 	struct scmi_msg_sensor_reading_get *sensor;
+	struct sensors_info *si = handle->sensor_priv;
+	struct scmi_sensor_info *s = si->sensors + sensor_id;
 
 	ret = scmi_xfer_get_init(handle, SENSOR_READING_GET,
 				 SCMI_PROTOCOL_SENSOR, sizeof(*sensor),
@@ -223,14 +230,18 @@ static int scmi_sensor_reading_get(const struct scmi_handle *handle,
 
 	sensor = t->tx.buf;
 	sensor->id = cpu_to_le32(sensor_id);
-	sensor->flags = cpu_to_le32(async ? SENSOR_READ_ASYNC : 0);
 
-	ret = scmi_do_xfer(handle, t);
-	if (!ret) {
-		__le32 *pval = t->rx.buf;
-
-		*value = le32_to_cpu(*pval);
-		*value |= (u64)le32_to_cpu(*(pval + 1)) << 32;
+	if (s->async) {
+		sensor->flags = cpu_to_le32(SENSOR_READ_ASYNC);
+		ret = scmi_do_xfer_with_response(handle, t);
+		if (!ret)
+			*value = get_unaligned_le64((void *)
+						    ((__le32 *)t->rx.buf + 1));
+	} else {
+		sensor->flags = cpu_to_le32(0);
+		ret = scmi_do_xfer(handle, t);
+		if (!ret)
+			*value = get_unaligned_le64(t->rx.buf);
 	}
 
 	scmi_xfer_put(handle, t);
@@ -255,8 +266,8 @@ static int scmi_sensor_count_get(const struct scmi_handle *handle)
 static struct scmi_sensor_ops sensor_ops = {
 	.count_get = scmi_sensor_count_get,
 	.info_get = scmi_sensor_info_get,
-	.configuration_set = scmi_sensor_configuration_set,
-	.trip_point_set = scmi_sensor_trip_point_set,
+	.trip_point_notify = scmi_sensor_trip_point_notify,
+	.trip_point_config = scmi_sensor_trip_point_config,
 	.reading_get = scmi_sensor_reading_get,
 };
 
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index bb13c266c329..eef4886a3bc3 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -1445,6 +1445,15 @@ config GPIO_XRA1403
 	help
 	  GPIO driver for EXAR XRA1403 16-bit SPI-based GPIO expander.
 
+config GPIO_MOXTET
+	tristate "Turris Mox Moxtet bus GPIO expander"
+	depends on MOXTET
+	help
+	  Say yes here if you are building for the Turris Mox router.
+	  This is the driver needed for configuring the GPIOs via the Moxtet
+	  bus. For example the Mox module with SFP cage needs this driver
+	  so that phylink can use corresponding GPIOs.
+
 endmenu
 
 menu "USB GPIO expanders"
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index a4e91175c708..2e10caec23ae 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -93,6 +93,7 @@ obj-$(CONFIG_GPIO_ML_IOH)		+= gpio-ml-ioh.o
 obj-$(CONFIG_GPIO_MLXBF)		+= gpio-mlxbf.o
 obj-$(CONFIG_GPIO_MM_LANTIQ)		+= gpio-mm-lantiq.o
 obj-$(CONFIG_GPIO_MOCKUP)		+= gpio-mockup.o
+obj-$(CONFIG_GPIO_MOXTET)		+= gpio-moxtet.o
 obj-$(CONFIG_GPIO_MPC5200)		+= gpio-mpc5200.o
 obj-$(CONFIG_GPIO_MPC8XXX)		+= gpio-mpc8xxx.o
 obj-$(CONFIG_GPIO_MSIC)			+= gpio-msic.o
diff --git a/drivers/gpio/gpio-moxtet.c b/drivers/gpio/gpio-moxtet.c
new file mode 100644
index 000000000000..3fd729994a38
--- /dev/null
+++ b/drivers/gpio/gpio-moxtet.c
@@ -0,0 +1,179 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Turris Mox Moxtet GPIO expander
+ *
+ *  Copyright (C) 2018 Marek Behun <marek.behun@nic.cz>
+ */
+
+#include <linux/bitops.h>
+#include <linux/gpio/driver.h>
+#include <linux/moxtet.h>
+#include <linux/module.h>
+
+#define MOXTET_GPIO_NGPIOS	12
+#define MOXTET_GPIO_INPUTS	4
+
+struct moxtet_gpio_desc {
+	u16 in_mask;
+	u16 out_mask;
+};
+
+static const struct moxtet_gpio_desc descs[] = {
+	[TURRIS_MOX_MODULE_SFP] = {
+		.in_mask = GENMASK(2, 0),
+		.out_mask = GENMASK(5, 4),
+	},
+};
+
+struct moxtet_gpio_chip {
+	struct device			*dev;
+	struct gpio_chip		gpio_chip;
+	const struct moxtet_gpio_desc	*desc;
+};
+
+static int moxtet_gpio_get_value(struct gpio_chip *gc, unsigned int offset)
+{
+	struct moxtet_gpio_chip *chip = gpiochip_get_data(gc);
+	int ret;
+
+	if (chip->desc->in_mask & BIT(offset)) {
+		ret = moxtet_device_read(chip->dev);
+	} else if (chip->desc->out_mask & BIT(offset)) {
+		ret = moxtet_device_written(chip->dev);
+		if (ret >= 0)
+			ret <<= MOXTET_GPIO_INPUTS;
+	} else {
+		return -EINVAL;
+	}
+
+	if (ret < 0)
+		return ret;
+
+	return !!(ret & BIT(offset));
+}
+
+static void moxtet_gpio_set_value(struct gpio_chip *gc, unsigned int offset,
+				  int val)
+{
+	struct moxtet_gpio_chip *chip = gpiochip_get_data(gc);
+	int state;
+
+	state = moxtet_device_written(chip->dev);
+	if (state < 0)
+		return;
+
+	offset -= MOXTET_GPIO_INPUTS;
+
+	if (val)
+		state |= BIT(offset);
+	else
+		state &= ~BIT(offset);
+
+	moxtet_device_write(chip->dev, state);
+}
+
+static int moxtet_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
+{
+	struct moxtet_gpio_chip *chip = gpiochip_get_data(gc);
+
+	/* All lines are hard wired to be either input or output, not both. */
+	if (chip->desc->in_mask & BIT(offset))
+		return 1;
+	else if (chip->desc->out_mask & BIT(offset))
+		return 0;
+	else
+		return -EINVAL;
+}
+
+static int moxtet_gpio_direction_input(struct gpio_chip *gc,
+				       unsigned int offset)
+{
+	struct moxtet_gpio_chip *chip = gpiochip_get_data(gc);
+
+	if (chip->desc->in_mask & BIT(offset))
+		return 0;
+	else if (chip->desc->out_mask & BIT(offset))
+		return -ENOTSUPP;
+	else
+		return -EINVAL;
+}
+
+static int moxtet_gpio_direction_output(struct gpio_chip *gc,
+					unsigned int offset, int val)
+{
+	struct moxtet_gpio_chip *chip = gpiochip_get_data(gc);
+
+	if (chip->desc->out_mask & BIT(offset))
+		moxtet_gpio_set_value(gc, offset, val);
+	else if (chip->desc->in_mask & BIT(offset))
+		return -ENOTSUPP;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static int moxtet_gpio_probe(struct device *dev)
+{
+	struct moxtet_gpio_chip *chip;
+	struct device_node *nc = dev->of_node;
+	int id;
+
+	id = to_moxtet_device(dev)->id;
+
+	if (id >= ARRAY_SIZE(descs)) {
+		dev_err(dev, "%pOF Moxtet device id 0x%x is not supported by gpio-moxtet driver\n",
+			nc, id);
+		return -ENOTSUPP;
+	}
+
+	chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->dev = dev;
+	chip->gpio_chip.parent = dev;
+	chip->desc = &descs[id];
+
+	dev_set_drvdata(dev, chip);
+
+	chip->gpio_chip.label = dev_name(dev);
+	chip->gpio_chip.get_direction = moxtet_gpio_get_direction;
+	chip->gpio_chip.direction_input = moxtet_gpio_direction_input;
+	chip->gpio_chip.direction_output = moxtet_gpio_direction_output;
+	chip->gpio_chip.get = moxtet_gpio_get_value;
+	chip->gpio_chip.set = moxtet_gpio_set_value;
+	chip->gpio_chip.base = -1;
+
+	chip->gpio_chip.ngpio = MOXTET_GPIO_NGPIOS;
+
+	chip->gpio_chip.can_sleep = true;
+	chip->gpio_chip.owner = THIS_MODULE;
+
+	return devm_gpiochip_add_data(dev, &chip->gpio_chip, chip);
+}
+
+static const struct of_device_id moxtet_gpio_dt_ids[] = {
+	{ .compatible = "cznic,moxtet-gpio", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, moxtet_gpio_dt_ids);
+
+static const enum turris_mox_module_id moxtet_gpio_module_table[] = {
+	TURRIS_MOX_MODULE_SFP,
+	0,
+};
+
+static struct moxtet_driver moxtet_gpio_driver = {
+	.driver = {
+		.name		= "moxtet-gpio",
+		.of_match_table	= moxtet_gpio_dt_ids,
+		.probe		= moxtet_gpio_probe,
+	},
+	.id_table = moxtet_gpio_module_table,
+};
+module_moxtet_driver(moxtet_gpio_driver);
+
+MODULE_AUTHOR("Marek Behun <marek.behun@nic.cz>");
+MODULE_DESCRIPTION("Turris Mox Moxtet GPIO expander");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/hwmon/scmi-hwmon.c b/drivers/hwmon/scmi-hwmon.c
index 0c93fc5ca762..8a7732c0bef3 100644
--- a/drivers/hwmon/scmi-hwmon.c
+++ b/drivers/hwmon/scmi-hwmon.c
@@ -72,7 +72,7 @@ static int scmi_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
 	const struct scmi_handle *h = scmi_sensors->handle;
 
 	sensor = *(scmi_sensors->info[type] + channel);
-	ret = h->sensor_ops->reading_get(h, sensor->id, false, &value);
+	ret = h->sensor_ops->reading_get(h, sensor->id, &value);
 	if (ret)
 		return ret;
 
diff --git a/drivers/reset/Kconfig b/drivers/reset/Kconfig
index 21efb7d39d62..7b07281aa0ae 100644
--- a/drivers/reset/Kconfig
+++ b/drivers/reset/Kconfig
@@ -116,9 +116,20 @@ config RESET_QCOM_PDC
 	  to control reset signals provided by PDC for Modem, Compute,
 	  Display, GPU, Debug, AOP, Sensors, Audio, SP and APPS.
 
+config RESET_SCMI
+	tristate "Reset driver controlled via ARM SCMI interface"
+	depends on ARM_SCMI_PROTOCOL || COMPILE_TEST
+	default ARM_SCMI_PROTOCOL
+	help
+	  This driver provides support for reset signal/domains that are
+	  controlled by firmware that implements the SCMI interface.
+
+	  This driver uses SCMI Message Protocol to interact with the
+	  firmware controlling all the reset signals.
+
 config RESET_SIMPLE
 	bool "Simple Reset Controller Driver" if COMPILE_TEST
-	default ARCH_STM32 || ARCH_STRATIX10 || ARCH_SUNXI || ARCH_ZX || ARCH_ASPEED || ARCH_BITMAIN
+	default ARCH_STM32 || ARCH_STRATIX10 || ARCH_SUNXI || ARCH_ZX || ARCH_ASPEED || ARCH_BITMAIN || ARC
 	help
 	  This enables a simple reset controller driver for reset lines that
 	  that can be asserted and deasserted by toggling bits in a contiguous,
diff --git a/drivers/reset/Makefile b/drivers/reset/Makefile
index 61456b8f659c..cf60ce526064 100644
--- a/drivers/reset/Makefile
+++ b/drivers/reset/Makefile
@@ -18,6 +18,7 @@ obj-$(CONFIG_RESET_OXNAS) += reset-oxnas.o
 obj-$(CONFIG_RESET_PISTACHIO) += reset-pistachio.o
 obj-$(CONFIG_RESET_QCOM_AOSS) += reset-qcom-aoss.o
 obj-$(CONFIG_RESET_QCOM_PDC) += reset-qcom-pdc.o
+obj-$(CONFIG_RESET_SCMI) += reset-scmi.o
 obj-$(CONFIG_RESET_SIMPLE) += reset-simple.o
 obj-$(CONFIG_RESET_STM32MP157) += reset-stm32mp1.o
 obj-$(CONFIG_RESET_SOCFPGA) += reset-socfpga.o
diff --git a/drivers/reset/reset-imx7.c b/drivers/reset/reset-imx7.c
index 3ecd770f910b..1443a55a0c29 100644
--- a/drivers/reset/reset-imx7.c
+++ b/drivers/reset/reset-imx7.c
@@ -169,9 +169,9 @@ static const struct imx7_src_signal imx8mq_src_signals[IMX8MQ_RESET_NUM] = {
 	[IMX8MQ_RESET_OTG2_PHY_RESET]		= { SRC_USBOPHY2_RCR, BIT(0) },
 	[IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N]	= { SRC_MIPIPHY_RCR, BIT(1) },
 	[IMX8MQ_RESET_MIPI_DSI_RESET_N]		= { SRC_MIPIPHY_RCR, BIT(2) },
-	[IMX8MQ_RESET_MIPI_DIS_DPI_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(3) },
-	[IMX8MQ_RESET_MIPI_DIS_ESC_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(4) },
-	[IMX8MQ_RESET_MIPI_DIS_PCLK_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(5) },
+	[IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(3) },
+	[IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(4) },
+	[IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(5) },
 	[IMX8MQ_RESET_PCIEPHY]			= { SRC_PCIEPHY_RCR,
 						    BIT(2) | BIT(1) },
 	[IMX8MQ_RESET_PCIEPHY_PERST]		= { SRC_PCIEPHY_RCR, BIT(3) },
@@ -220,9 +220,9 @@ static int imx8mq_reset_set(struct reset_controller_dev *rcdev,
 
 	case IMX8MQ_RESET_PCIE_CTRL_APPS_EN:
 	case IMX8MQ_RESET_PCIE2_CTRL_APPS_EN:	/* fallthrough */
-	case IMX8MQ_RESET_MIPI_DIS_PCLK_RESET_N:	/* fallthrough */
-	case IMX8MQ_RESET_MIPI_DIS_ESC_RESET_N:	/* fallthrough */
-	case IMX8MQ_RESET_MIPI_DIS_DPI_RESET_N:	/* fallthrough */
+	case IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N:	/* fallthrough */
+	case IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N:	/* fallthrough */
+	case IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N:	/* fallthrough */
 	case IMX8MQ_RESET_MIPI_DSI_RESET_N:	/* fallthrough */
 	case IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N:	/* fallthrough */
 		value = assert ? 0 : bit;
diff --git a/drivers/reset/reset-meson.c b/drivers/reset/reset-meson.c
index 5242e0679df7..7d05d766e1ea 100644
--- a/drivers/reset/reset-meson.c
+++ b/drivers/reset/reset-meson.c
@@ -1,58 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
 /*
  * Amlogic Meson Reset Controller driver
  *
- * This file is provided under a dual BSD/GPLv2 license.  When using or
- * redistributing this file, you may do so under either license.
- *
- * GPL LICENSE SUMMARY
- *
- * Copyright (c) 2016 BayLibre, SAS.
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of version 2 of the GNU General Public License as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see <http://www.gnu.org/licenses/>.
- * The full GNU General Public License is included in this distribution
- * in the file called COPYING.
- *
- * BSD LICENSE
- *
  * Copyright (c) 2016 BayLibre, SAS.
  * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- *   * Redistributions of source code must retain the above copyright
- *     notice, this list of conditions and the following disclaimer.
- *   * Redistributions in binary form must reproduce the above copyright
- *     notice, this list of conditions and the following disclaimer in
- *     the documentation and/or other materials provided with the
- *     distribution.
- *   * Neither the name of Intel Corporation nor the names of its
- *     contributors may be used to endorse or promote products derived
- *     from this software without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */
 #include <linux/err.h>
 #include <linux/init.h>
diff --git a/drivers/reset/reset-scmi.c b/drivers/reset/reset-scmi.c
new file mode 100644
index 000000000000..c6d3c8427f14
--- /dev/null
+++ b/drivers/reset/reset-scmi.c
@@ -0,0 +1,124 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ARM System Control and Management Interface (ARM SCMI) reset driver
+ *
+ * Copyright (C) 2019 ARM Ltd.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/device.h>
+#include <linux/reset-controller.h>
+#include <linux/scmi_protocol.h>
+
+/**
+ * struct scmi_reset_data - reset controller information structure
+ * @rcdev: reset controller entity
+ * @handle: ARM SCMI handle used for communication with system controller
+ */
+struct scmi_reset_data {
+	struct reset_controller_dev rcdev;
+	const struct scmi_handle *handle;
+};
+
+#define to_scmi_reset_data(p)	container_of((p), struct scmi_reset_data, rcdev)
+#define to_scmi_handle(p)	(to_scmi_reset_data(p)->handle)
+
+/**
+ * scmi_reset_assert() - assert device reset
+ * @rcdev: reset controller entity
+ * @id: ID of the reset to be asserted
+ *
+ * This function implements the reset driver op to assert a device's reset
+ * using the ARM SCMI protocol.
+ *
+ * Return: 0 for successful request, else a corresponding error value
+ */
+static int
+scmi_reset_assert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	const struct scmi_handle *handle = to_scmi_handle(rcdev);
+
+	return handle->reset_ops->assert(handle, id);
+}
+
+/**
+ * scmi_reset_deassert() - deassert device reset
+ * @rcdev: reset controller entity
+ * @id: ID of the reset to be deasserted
+ *
+ * This function implements the reset driver op to deassert a device's reset
+ * using the ARM SCMI protocol.
+ *
+ * Return: 0 for successful request, else a corresponding error value
+ */
+static int
+scmi_reset_deassert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	const struct scmi_handle *handle = to_scmi_handle(rcdev);
+
+	return handle->reset_ops->deassert(handle, id);
+}
+
+/**
+ * scmi_reset_reset() - reset the device
+ * @rcdev: reset controller entity
+ * @id: ID of the reset signal to be reset(assert + deassert)
+ *
+ * This function implements the reset driver op to trigger a device's
+ * reset signal using the ARM SCMI protocol.
+ *
+ * Return: 0 for successful request, else a corresponding error value
+ */
+static int
+scmi_reset_reset(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	const struct scmi_handle *handle = to_scmi_handle(rcdev);
+
+	return handle->reset_ops->reset(handle, id);
+}
+
+static const struct reset_control_ops scmi_reset_ops = {
+	.assert		= scmi_reset_assert,
+	.deassert	= scmi_reset_deassert,
+	.reset		= scmi_reset_reset,
+};
+
+static int scmi_reset_probe(struct scmi_device *sdev)
+{
+	struct scmi_reset_data *data;
+	struct device *dev = &sdev->dev;
+	struct device_node *np = dev->of_node;
+	const struct scmi_handle *handle = sdev->handle;
+
+	if (!handle || !handle->reset_ops)
+		return -ENODEV;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->rcdev.ops = &scmi_reset_ops;
+	data->rcdev.owner = THIS_MODULE;
+	data->rcdev.of_node = np;
+	data->rcdev.nr_resets = handle->reset_ops->num_domains_get(handle);
+
+	return devm_reset_controller_register(dev, &data->rcdev);
+}
+
+static const struct scmi_device_id scmi_id_table[] = {
+	{ SCMI_PROTOCOL_RESET },
+	{ },
+};
+MODULE_DEVICE_TABLE(scmi, scmi_id_table);
+
+static struct scmi_driver scmi_reset_driver = {
+	.name = "scmi-reset",
+	.probe = scmi_reset_probe,
+	.id_table = scmi_id_table,
+};
+module_scmi_driver(scmi_reset_driver);
+
+MODULE_AUTHOR("Sudeep Holla <sudeep.holla@arm.com>");
+MODULE_DESCRIPTION("ARM SCMI reset controller driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/reset/reset-simple.c b/drivers/reset/reset-simple.c
index 1154f7b1f4dd..067e7e7b34f1 100644
--- a/drivers/reset/reset-simple.c
+++ b/drivers/reset/reset-simple.c
@@ -127,6 +127,9 @@ static const struct of_device_id reset_simple_dt_ids[] = {
 	{ .compatible = "aspeed,ast2500-lpc-reset" },
 	{ .compatible = "bitmain,bm1880-reset",
 		.data = &reset_simple_active_low },
+	{ .compatible = "snps,dw-high-reset" },
+	{ .compatible = "snps,dw-low-reset",
+		.data = &reset_simple_active_low },
 	{ /* sentinel */ },
 };
 
diff --git a/drivers/soc/fsl/dpaa2-console.c b/drivers/soc/fsl/dpaa2-console.c
index 9168d8ddc932..27243f706f37 100644
--- a/drivers/soc/fsl/dpaa2-console.c
+++ b/drivers/soc/fsl/dpaa2-console.c
@@ -73,7 +73,7 @@ static u64 get_mc_fw_base_address(void)
 
 	mcfbaregs = ioremap(mc_base_addr.start, resource_size(&mc_base_addr));
 	if (!mcfbaregs) {
-		pr_err("could not map MC Firmaware Base registers\n");
+		pr_err("could not map MC Firmware Base registers\n");
 		return 0;
 	}
 
diff --git a/drivers/soc/fsl/qe/qe.c b/drivers/soc/fsl/qe/qe.c
index c9519e62308c..417df7e19281 100644
--- a/drivers/soc/fsl/qe/qe.c
+++ b/drivers/soc/fsl/qe/qe.c
@@ -10,6 +10,7 @@
  * General Purpose functions for the global management of the
  * QUICC Engine (QE).
  */
+#include <linux/bitmap.h>
 #include <linux/errno.h>
 #include <linux/sched.h>
 #include <linux/kernel.h>
@@ -39,29 +40,32 @@ static DEFINE_SPINLOCK(qe_lock);
 DEFINE_SPINLOCK(cmxgcr_lock);
 EXPORT_SYMBOL(cmxgcr_lock);
 
-/* QE snum state */
-enum qe_snum_state {
-	QE_SNUM_STATE_USED,
-	QE_SNUM_STATE_FREE
-};
-
-/* QE snum */
-struct qe_snum {
-	u8 num;
-	enum qe_snum_state state;
-};
-
 /* We allocate this here because it is used almost exclusively for
  * the communication processor devices.
  */
 struct qe_immap __iomem *qe_immr;
 EXPORT_SYMBOL(qe_immr);
 
-static struct qe_snum snums[QE_NUM_OF_SNUM];	/* Dynamically allocated SNUMs */
+static u8 snums[QE_NUM_OF_SNUM];	/* Dynamically allocated SNUMs */
+static DECLARE_BITMAP(snum_state, QE_NUM_OF_SNUM);
 static unsigned int qe_num_of_snum;
 
 static phys_addr_t qebase = -1;
 
+static struct device_node *qe_get_device_node(void)
+{
+	struct device_node *qe;
+
+	/*
+	 * Newer device trees have an "fsl,qe" compatible property for the QE
+	 * node, but we still need to support older device trees.
+	 */
+	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
+	if (qe)
+		return qe;
+	return of_find_node_by_type(NULL, "qe");
+}
+
 static phys_addr_t get_qe_base(void)
 {
 	struct device_node *qe;
@@ -71,12 +75,9 @@ static phys_addr_t get_qe_base(void)
 	if (qebase != -1)
 		return qebase;
 
-	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!qe) {
-		qe = of_find_node_by_type(NULL, "qe");
-		if (!qe)
-			return qebase;
-	}
+	qe = qe_get_device_node();
+	if (!qe)
+		return qebase;
 
 	ret = of_address_to_resource(qe, 0, &res);
 	if (!ret)
@@ -170,12 +171,9 @@ unsigned int qe_get_brg_clk(void)
 	if (brg_clk)
 		return brg_clk;
 
-	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!qe) {
-		qe = of_find_node_by_type(NULL, "qe");
-		if (!qe)
-			return brg_clk;
-	}
+	qe = qe_get_device_node();
+	if (!qe)
+		return brg_clk;
 
 	prop = of_get_property(qe, "brg-frequency", &size);
 	if (prop && size == sizeof(*prop))
@@ -281,7 +279,6 @@ EXPORT_SYMBOL(qe_clock_source);
  */
 static void qe_snums_init(void)
 {
-	int i;
 	static const u8 snum_init_76[] = {
 		0x04, 0x05, 0x0C, 0x0D, 0x14, 0x15, 0x1C, 0x1D,
 		0x24, 0x25, 0x2C, 0x2D, 0x34, 0x35, 0x88, 0x89,
@@ -302,19 +299,39 @@ static void qe_snums_init(void)
 		0x28, 0x29, 0x38, 0x39, 0x48, 0x49, 0x58, 0x59,
 		0x68, 0x69, 0x78, 0x79, 0x80, 0x81,
 	};
-	static const u8 *snum_init;
+	struct device_node *qe;
+	const u8 *snum_init;
+	int i;
 
-	qe_num_of_snum = qe_get_num_of_snums();
+	bitmap_zero(snum_state, QE_NUM_OF_SNUM);
+	qe_num_of_snum = 28; /* The default number of snum for threads is 28 */
+	qe = qe_get_device_node();
+	if (qe) {
+		i = of_property_read_variable_u8_array(qe, "fsl,qe-snums",
+						       snums, 1, QE_NUM_OF_SNUM);
+		if (i > 0) {
+			of_node_put(qe);
+			qe_num_of_snum = i;
+			return;
+		}
+		/*
+		 * Fall back to legacy binding of using the value of
+		 * fsl,qe-num-snums to choose one of the static arrays
+		 * above.
+		 */
+		of_property_read_u32(qe, "fsl,qe-num-snums", &qe_num_of_snum);
+		of_node_put(qe);
+	}
 
-	if (qe_num_of_snum == 76)
+	if (qe_num_of_snum == 76) {
 		snum_init = snum_init_76;
-	else
+	} else if (qe_num_of_snum == 28 || qe_num_of_snum == 46) {
 		snum_init = snum_init_46;
-
-	for (i = 0; i < qe_num_of_snum; i++) {
-		snums[i].num = snum_init[i];
-		snums[i].state = QE_SNUM_STATE_FREE;
+	} else {
+		pr_err("QE: unsupported value of fsl,qe-num-snums: %u\n", qe_num_of_snum);
+		return;
 	}
+	memcpy(snums, snum_init, qe_num_of_snum);
 }
 
 int qe_get_snum(void)
@@ -324,12 +341,10 @@ int qe_get_snum(void)
 	int i;
 
 	spin_lock_irqsave(&qe_lock, flags);
-	for (i = 0; i < qe_num_of_snum; i++) {
-		if (snums[i].state == QE_SNUM_STATE_FREE) {
-			snums[i].state = QE_SNUM_STATE_USED;
-			snum = snums[i].num;
-			break;
-		}
+	i = find_first_zero_bit(snum_state, qe_num_of_snum);
+	if (i < qe_num_of_snum) {
+		set_bit(i, snum_state);
+		snum = snums[i];
 	}
 	spin_unlock_irqrestore(&qe_lock, flags);
 
@@ -339,14 +354,10 @@ EXPORT_SYMBOL(qe_get_snum);
 
 void qe_put_snum(u8 snum)
 {
-	int i;
+	const u8 *p = memchr(snums, snum, qe_num_of_snum);
 
-	for (i = 0; i < qe_num_of_snum; i++) {
-		if (snums[i].num == snum) {
-			snums[i].state = QE_SNUM_STATE_FREE;
-			break;
-		}
-	}
+	if (p)
+		clear_bit(p - snums, snum_state);
 }
 EXPORT_SYMBOL(qe_put_snum);
 
@@ -572,16 +583,9 @@ struct qe_firmware_info *qe_get_firmware_info(void)
 
 	initialized = 1;
 
-	/*
-	 * Newer device trees have an "fsl,qe" compatible property for the QE
-	 * node, but we still need to support older device trees.
-	*/
-	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!qe) {
-		qe = of_find_node_by_type(NULL, "qe");
-		if (!qe)
-			return NULL;
-	}
+	qe = qe_get_device_node();
+	if (!qe)
+		return NULL;
 
 	/* Find the 'firmware' child node */
 	fw = of_get_child_by_name(qe, "firmware");
@@ -627,16 +631,9 @@ unsigned int qe_get_num_of_risc(void)
 	unsigned int num_of_risc = 0;
 	const u32 *prop;
 
-	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!qe) {
-		/* Older devices trees did not have an "fsl,qe"
-		 * compatible property, so we need to look for
-		 * the QE node by name.
-		 */
-		qe = of_find_node_by_type(NULL, "qe");
-		if (!qe)
-			return num_of_risc;
-	}
+	qe = qe_get_device_node();
+	if (!qe)
+		return num_of_risc;
 
 	prop = of_get_property(qe, "fsl,qe-num-riscs", &size);
 	if (prop && size == sizeof(*prop))
@@ -650,37 +647,7 @@ EXPORT_SYMBOL(qe_get_num_of_risc);
 
 unsigned int qe_get_num_of_snums(void)
 {
-	struct device_node *qe;
-	int size;
-	unsigned int num_of_snums;
-	const u32 *prop;
-
-	num_of_snums = 28; /* The default number of snum for threads is 28 */
-	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!qe) {
-		/* Older devices trees did not have an "fsl,qe"
-		 * compatible property, so we need to look for
-		 * the QE node by name.
-		 */
-		qe = of_find_node_by_type(NULL, "qe");
-		if (!qe)
-			return num_of_snums;
-	}
-
-	prop = of_get_property(qe, "fsl,qe-num-snums", &size);
-	if (prop && size == sizeof(*prop)) {
-		num_of_snums = *prop;
-		if ((num_of_snums < 28) || (num_of_snums > QE_NUM_OF_SNUM)) {
-			/* No QE ever has fewer than 28 SNUMs */
-			pr_err("QE: number of snum is invalid\n");
-			of_node_put(qe);
-			return -EINVAL;
-		}
-	}
-
-	of_node_put(qe);
-
-	return num_of_snums;
+	return qe_num_of_snum;
 }
 EXPORT_SYMBOL(qe_get_num_of_snums);
 
diff --git a/drivers/soc/renesas/rcar-sysc.c b/drivers/soc/renesas/rcar-sysc.c
index 0c80fab4f8de..02b29ea62dc4 100644
--- a/drivers/soc/renesas/rcar-sysc.c
+++ b/drivers/soc/renesas/rcar-sysc.c
@@ -170,7 +170,7 @@ struct rcar_sysc_pd {
 	struct generic_pm_domain genpd;
 	struct rcar_sysc_ch ch;
 	unsigned int flags;
-	char name[0];
+	char name[];
 };
 
 static inline struct rcar_sysc_pd *to_rcar_pd(struct generic_pm_domain *d)
diff --git a/drivers/tee/optee/call.c b/drivers/tee/optee/call.c
index aa942703ae65..13b0269a0abc 100644
--- a/drivers/tee/optee/call.c
+++ b/drivers/tee/optee/call.c
@@ -148,6 +148,7 @@ u32 optee_do_call_with_arg(struct tee_context *ctx, phys_addr_t parg)
 			 */
 			optee_cq_wait_for_completion(&optee->call_queue, &w);
 		} else if (OPTEE_SMC_RETURN_IS_RPC(res.a0)) {
+			might_sleep();
 			param.a0 = res.a0;
 			param.a1 = res.a1;
 			param.a2 = res.a2;
diff --git a/include/dt-bindings/bus/moxtet.h b/include/dt-bindings/bus/moxtet.h
new file mode 100644
index 000000000000..dc9345440ebe
--- /dev/null
+++ b/include/dt-bindings/bus/moxtet.h
@@ -0,0 +1,16 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Constant for device tree bindings for Turris Mox module configuration bus
+ *
+ * Copyright (C) 2019 Marek Behun <marek.behun@nic.cz>
+ */
+
+#ifndef _DT_BINDINGS_BUS_MOXTET_H
+#define _DT_BINDINGS_BUS_MOXTET_H
+
+#define MOXTET_IRQ_PCI		0
+#define MOXTET_IRQ_USB3		4
+#define MOXTET_IRQ_PERIDOT(n)	(8 + (n))
+#define MOXTET_IRQ_TOPAZ	12
+
+#endif /* _DT_BINDINGS_BUS_MOXTET_H */
diff --git a/include/dt-bindings/reset/amlogic,meson-gxbb-reset.h b/include/dt-bindings/reset/amlogic,meson-gxbb-reset.h
index 524d6077ac1b..ea5058618863 100644
--- a/include/dt-bindings/reset/amlogic,meson-gxbb-reset.h
+++ b/include/dt-bindings/reset/amlogic,meson-gxbb-reset.h
@@ -1,56 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
 /*
- * This file is provided under a dual BSD/GPLv2 license.  When using or
- * redistributing this file, you may do so under either license.
- *
- * GPL LICENSE SUMMARY
- *
  * Copyright (c) 2016 BayLibre, SAS.
  * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of version 2 of the GNU General Public License as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see <http://www.gnu.org/licenses/>.
- * The full GNU General Public License is included in this distribution
- * in the file called COPYING.
- *
- * BSD LICENSE
- *
- * Copyright (c) 2016 BayLibre, SAS.
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- *   * Redistributions of source code must retain the above copyright
- *     notice, this list of conditions and the following disclaimer.
- *   * Redistributions in binary form must reproduce the above copyright
- *     notice, this list of conditions and the following disclaimer in
- *     the documentation and/or other materials provided with the
- *     distribution.
- *   * Neither the name of Intel Corporation nor the names of its
- *     contributors may be used to endorse or promote products derived
- *     from this software without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */
 #ifndef _DT_BINDINGS_AMLOGIC_MESON_GXBB_RESET_H
 #define _DT_BINDINGS_AMLOGIC_MESON_GXBB_RESET_H
diff --git a/include/dt-bindings/reset/amlogic,meson8b-reset.h b/include/dt-bindings/reset/amlogic,meson8b-reset.h
index 614aff2c7aff..c614438bcbdb 100644
--- a/include/dt-bindings/reset/amlogic,meson8b-reset.h
+++ b/include/dt-bindings/reset/amlogic,meson8b-reset.h
@@ -1,56 +1,7 @@
+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
 /*
- * This file is provided under a dual BSD/GPLv2 license.  When using or
- * redistributing this file, you may do so under either license.
- *
- * GPL LICENSE SUMMARY
- *
  * Copyright (c) 2016 BayLibre, SAS.
  * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of version 2 of the GNU General Public License as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see <http://www.gnu.org/licenses/>.
- * The full GNU General Public License is included in this distribution
- * in the file called COPYING.
- *
- * BSD LICENSE
- *
- * Copyright (c) 2016 BayLibre, SAS.
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- *   * Redistributions of source code must retain the above copyright
- *     notice, this list of conditions and the following disclaimer.
- *   * Redistributions in binary form must reproduce the above copyright
- *     notice, this list of conditions and the following disclaimer in
- *     the documentation and/or other materials provided with the
- *     distribution.
- *   * Neither the name of Intel Corporation nor the names of its
- *     contributors may be used to endorse or promote products derived
- *     from this software without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */
 #ifndef _DT_BINDINGS_AMLOGIC_MESON8B_RESET_H
 #define _DT_BINDINGS_AMLOGIC_MESON8B_RESET_H
diff --git a/include/dt-bindings/reset/imx8mq-reset.h b/include/dt-bindings/reset/imx8mq-reset.h
index 57c592498aa0..9a301082d361 100644
--- a/include/dt-bindings/reset/imx8mq-reset.h
+++ b/include/dt-bindings/reset/imx8mq-reset.h
@@ -31,33 +31,33 @@
 #define IMX8MQ_RESET_OTG2_PHY_RESET		20
 #define IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N	21
 #define IMX8MQ_RESET_MIPI_DSI_RESET_N		22
-#define IMX8MQ_RESET_MIPI_DIS_DPI_RESET_N	23
-#define IMX8MQ_RESET_MIPI_DIS_ESC_RESET_N	24
-#define IMX8MQ_RESET_MIPI_DIS_PCLK_RESET_N	25
+#define IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N	23
+#define IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N	24
+#define IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N	25
 #define IMX8MQ_RESET_PCIEPHY			26
 #define IMX8MQ_RESET_PCIEPHY_PERST		27
 #define IMX8MQ_RESET_PCIE_CTRL_APPS_EN		28
 #define IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF	29
-#define IMX8MQ_RESET_HDMI_PHY_APB_RESET		30
+#define IMX8MQ_RESET_HDMI_PHY_APB_RESET		30	/* i.MX8MM does NOT support */
 #define IMX8MQ_RESET_DISP_RESET			31
 #define IMX8MQ_RESET_GPU_RESET			32
 #define IMX8MQ_RESET_VPU_RESET			33
-#define IMX8MQ_RESET_PCIEPHY2			34
-#define IMX8MQ_RESET_PCIEPHY2_PERST		35
-#define IMX8MQ_RESET_PCIE2_CTRL_APPS_EN		36
-#define IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF	37
-#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET	38
-#define IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET	39
-#define IMX8MQ_RESET_MIPI_CSI1_ESC_RESET	40
-#define IMX8MQ_RESET_MIPI_CSI2_CORE_RESET	41
-#define IMX8MQ_RESET_MIPI_CSI2_PHY_REF_RESET	42
-#define IMX8MQ_RESET_MIPI_CSI2_ESC_RESET	43
+#define IMX8MQ_RESET_PCIEPHY2			34	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_PCIEPHY2_PERST		35	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_PCIE2_CTRL_APPS_EN		36	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF	37	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET	38	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET	39	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI1_ESC_RESET	40	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI2_CORE_RESET	41	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI2_PHY_REF_RESET	42	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI2_ESC_RESET	43	/* i.MX8MM does NOT support */
 #define IMX8MQ_RESET_DDRC1_PRST			44
 #define IMX8MQ_RESET_DDRC1_CORE_RESET		45
 #define IMX8MQ_RESET_DDRC1_PHY_RESET		46
-#define IMX8MQ_RESET_DDRC2_PRST			47
-#define IMX8MQ_RESET_DDRC2_CORE_RESET		48
-#define IMX8MQ_RESET_DDRC2_PHY_RESET		49
+#define IMX8MQ_RESET_DDRC2_PRST			47	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_DDRC2_CORE_RESET		48	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_DDRC2_PHY_RESET		49	/* i.MX8MM does NOT support */
 
 #define IMX8MQ_RESET_NUM			50
 
diff --git a/include/linux/moxtet.h b/include/linux/moxtet.h
new file mode 100644
index 000000000000..490db6886dcc
--- /dev/null
+++ b/include/linux/moxtet.h
@@ -0,0 +1,109 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Turris Mox module configuration bus driver
+ *
+ * Copyright (C) 2019 Marek Behun <marek.behun@nic.cz>
+ */
+
+#ifndef __LINUX_MOXTET_H
+#define __LINUX_MOXTET_H
+
+#include <linux/device.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/mutex.h>
+
+#define TURRIS_MOX_MAX_MODULES	10
+
+enum turris_mox_cpu_module_id {
+	TURRIS_MOX_CPU_ID_EMMC	= 0x00,
+	TURRIS_MOX_CPU_ID_SD	= 0x10,
+};
+
+enum turris_mox_module_id {
+	TURRIS_MOX_MODULE_FIRST		= 0x01,
+
+	TURRIS_MOX_MODULE_SFP		= 0x01,
+	TURRIS_MOX_MODULE_PCI		= 0x02,
+	TURRIS_MOX_MODULE_TOPAZ		= 0x03,
+	TURRIS_MOX_MODULE_PERIDOT	= 0x04,
+	TURRIS_MOX_MODULE_USB3		= 0x05,
+	TURRIS_MOX_MODULE_PCI_BRIDGE	= 0x06,
+
+	TURRIS_MOX_MODULE_LAST		= 0x06,
+};
+
+#define MOXTET_NIRQS	16
+
+extern struct bus_type moxtet_type;
+
+struct moxtet {
+	struct device			*dev;
+	struct mutex			lock;
+	u8				modules[TURRIS_MOX_MAX_MODULES];
+	int				count;
+	u8				tx[TURRIS_MOX_MAX_MODULES];
+	int				dev_irq;
+	struct {
+		struct irq_domain	*domain;
+		struct irq_chip		chip;
+		unsigned long		masked, exists;
+		struct moxtet_irqpos {
+					u8 idx;
+					u8 bit;
+		} position[MOXTET_NIRQS];
+	} irq;
+#ifdef CONFIG_DEBUG_FS
+	struct dentry			*debugfs_root;
+#endif
+};
+
+struct moxtet_driver {
+	const enum turris_mox_module_id	*id_table;
+	struct device_driver		driver;
+};
+
+static inline struct moxtet_driver *
+to_moxtet_driver(struct device_driver *drv)
+{
+	if (!drv)
+		return NULL;
+	return container_of(drv, struct moxtet_driver, driver);
+}
+
+extern int __moxtet_register_driver(struct module *owner,
+				    struct moxtet_driver *mdrv);
+
+static inline void moxtet_unregister_driver(struct moxtet_driver *mdrv)
+{
+	if (mdrv)
+		driver_unregister(&mdrv->driver);
+}
+
+#define moxtet_register_driver(driver) \
+	__moxtet_register_driver(THIS_MODULE, driver)
+
+#define module_moxtet_driver(__moxtet_driver) \
+	module_driver(__moxtet_driver, moxtet_register_driver, \
+			moxtet_unregister_driver)
+
+struct moxtet_device {
+	struct device			dev;
+	struct moxtet			*moxtet;
+	enum turris_mox_module_id	id;
+	unsigned int			idx;
+};
+
+extern int moxtet_device_read(struct device *dev);
+extern int moxtet_device_write(struct device *dev, u8 val);
+extern int moxtet_device_written(struct device *dev);
+
+static inline struct moxtet_device *
+to_moxtet_device(struct device *dev)
+{
+	if (!dev)
+		return NULL;
+	return container_of(dev, struct moxtet_device, dev);
+}
+
+#endif /* __LINUX_MOXTET_H */
diff --git a/include/linux/scmi_protocol.h b/include/linux/scmi_protocol.h
index 9ff2e9357e9a..881fea47c83d 100644
--- a/include/linux/scmi_protocol.h
+++ b/include/linux/scmi_protocol.h
@@ -1,4 +1,4 @@
-// SPDX-License-Identifier: GPL-2.0
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * SCMI Message Protocol driver header
  *
@@ -71,7 +71,7 @@ struct scmi_clk_ops {
 	int (*rate_get)(const struct scmi_handle *handle, u32 clk_id,
 			u64 *rate);
 	int (*rate_set)(const struct scmi_handle *handle, u32 clk_id,
-			u32 config, u64 rate);
+			u64 rate);
 	int (*enable)(const struct scmi_handle *handle, u32 clk_id);
 	int (*disable)(const struct scmi_handle *handle, u32 clk_id);
 };
@@ -145,6 +145,8 @@ struct scmi_sensor_info {
 	u32 id;
 	u8 type;
 	s8 scale;
+	u8 num_trip_points;
+	bool async;
 	char name[SCMI_MAX_STR_SIZE];
 };
 
@@ -167,9 +169,9 @@ enum scmi_sensor_class {
  *
  * @count_get: get the count of sensors provided by SCMI
  * @info_get: get the information of the specified sensor
- * @configuration_set: control notifications on cross-over events for
+ * @trip_point_notify: control notifications on cross-over events for
  *	the trip-points
- * @trip_point_set: selects and configures a trip-point of interest
+ * @trip_point_config: selects and configures a trip-point of interest
  * @reading_get: gets the current value of the sensor
  */
 struct scmi_sensor_ops {
@@ -177,12 +179,32 @@ struct scmi_sensor_ops {
 
 	const struct scmi_sensor_info *(*info_get)
 		(const struct scmi_handle *handle, u32 sensor_id);
-	int (*configuration_set)(const struct scmi_handle *handle,
-				 u32 sensor_id);
-	int (*trip_point_set)(const struct scmi_handle *handle, u32 sensor_id,
-			      u8 trip_id, u64 trip_value);
+	int (*trip_point_notify)(const struct scmi_handle *handle,
+				 u32 sensor_id, bool enable);
+	int (*trip_point_config)(const struct scmi_handle *handle,
+				 u32 sensor_id, u8 trip_id, u64 trip_value);
 	int (*reading_get)(const struct scmi_handle *handle, u32 sensor_id,
-			   bool async, u64 *value);
+			   u64 *value);
+};
+
+/**
+ * struct scmi_reset_ops - represents the various operations provided
+ *	by SCMI Reset Protocol
+ *
+ * @num_domains_get: get the count of reset domains provided by SCMI
+ * @name_get: gets the name of a reset domain
+ * @latency_get: gets the reset latency for the specified reset domain
+ * @reset: resets the specified reset domain
+ * @assert: explicitly assert reset signal of the specified reset domain
+ * @deassert: explicitly deassert reset signal of the specified reset domain
+ */
+struct scmi_reset_ops {
+	int (*num_domains_get)(const struct scmi_handle *handle);
+	char *(*name_get)(const struct scmi_handle *handle, u32 domain);
+	int (*latency_get)(const struct scmi_handle *handle, u32 domain);
+	int (*reset)(const struct scmi_handle *handle, u32 domain);
+	int (*assert)(const struct scmi_handle *handle, u32 domain);
+	int (*deassert)(const struct scmi_handle *handle, u32 domain);
 };
 
 /**
@@ -194,6 +216,7 @@ struct scmi_sensor_ops {
  * @perf_ops: pointer to set of performance protocol operations
  * @clk_ops: pointer to set of clock protocol operations
  * @sensor_ops: pointer to set of sensor protocol operations
+ * @reset_ops: pointer to set of reset protocol operations
  * @perf_priv: pointer to private data structure specific to performance
  *	protocol(for internal use only)
  * @clk_priv: pointer to private data structure specific to clock
@@ -202,6 +225,8 @@ struct scmi_sensor_ops {
  *	protocol(for internal use only)
  * @sensor_priv: pointer to private data structure specific to sensors
  *	protocol(for internal use only)
+ * @reset_priv: pointer to private data structure specific to reset
+ *	protocol(for internal use only)
  */
 struct scmi_handle {
 	struct device *dev;
@@ -210,11 +235,13 @@ struct scmi_handle {
 	struct scmi_clk_ops *clk_ops;
 	struct scmi_power_ops *power_ops;
 	struct scmi_sensor_ops *sensor_ops;
+	struct scmi_reset_ops *reset_ops;
 	/* for protocol internal use */
 	void *perf_priv;
 	void *clk_priv;
 	void *power_priv;
 	void *sensor_priv;
+	void *reset_priv;
 };
 
 enum scmi_std_protocol {
@@ -224,6 +251,7 @@ enum scmi_std_protocol {
 	SCMI_PROTOCOL_PERF = 0x13,
 	SCMI_PROTOCOL_CLOCK = 0x14,
 	SCMI_PROTOCOL_SENSOR = 0x15,
+	SCMI_PROTOCOL_RESET = 0x16,
 };
 
 struct scmi_device {