ARM: dts: imx28-apx4devkit: Convert to use label references

This board file still use node name and unit address to
reference parts from the imx28.dtsi . This causes a lot of
redundancy. So use label references in orer to make it
easier to maintain.

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Cc: Aapo Vienamo <aapo.vienamo@iki.fi>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>

1 files changed, 186 insertions, 194 deletions

diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts
index b86be320496b..f9bf40d96568 100644
--- a/arch/arm/boot/dts/imx28-apx4devkit.dts
+++ b/arch/arm/boot/dts/imx28-apx4devkit.dts
@@ -11,200 +11,6 @@
 		reg = <0x40000000 0x04000000>;
 	};
 
-	apb@80000000 {
-		apbh@80000000 {
-			nand-controller@8000c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
-				status = "okay";
-			};
-
-			ssp0: spi@80010000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			ssp2: spi@80014000 {
-				compatible = "fsl,imx28-mmc";
-				pinctrl-names = "default";
-				pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
-				bus-width = <4>;
-				status = "okay";
-			};
-
-			pinctrl@80018000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&hog_pins_a>;
-
-				hog_pins_a: hog@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_GPMI_CE1N__GPIO_0_17
-						MX28_PAD_GPMI_RDY1__GPIO_0_21
-						MX28_PAD_SSP2_MISO__GPIO_2_18
-						MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
-						MX28_PAD_PWM3__GPIO_3_28
-						MX28_PAD_LCD_RESET__GPIO_3_30
-						MX28_PAD_JTAG_RTCK__GPIO_4_20
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				lcdif_pins_apx4: lcdif-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_LCD_RD_E__LCD_VSYNC
-						MX28_PAD_LCD_WR_RWN__LCD_HSYNC
-						MX28_PAD_LCD_RS__LCD_DOTCLK
-						MX28_PAD_LCD_CS__LCD_ENABLE
-					>;
-					fsl,drive-strength = <MXS_DRIVE_4mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-
-				mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA4__SSP2_D0
-						MX28_PAD_SSP0_DATA5__SSP2_D3
-						MX28_PAD_SSP0_DATA6__SSP2_CMD
-						MX28_PAD_SSP0_DATA7__SSP2_SCK
-						MX28_PAD_SSP2_SS1__SSP2_D1
-						MX28_PAD_SSP2_SS2__SSP2_D2
-					>;
-					fsl,drive-strength = <MXS_DRIVE_8mA>;
-					fsl,voltage = <MXS_VOLTAGE_HIGH>;
-					fsl,pull-up = <MXS_PULL_ENABLE>;
-				};
-
-				mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4@0 {
-					reg = <0>;
-					fsl,pinmux-ids = <
-						MX28_PAD_SSP0_DATA7__SSP2_SCK
-					>;
-					fsl,drive-strength = <MXS_DRIVE_12mA>;
-					fsl,pull-up = <MXS_PULL_DISABLE>;
-				};
-			};
-
-			lcdif@80030000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&lcdif_24bit_pins_a
-					     &lcdif_pins_apx4>;
-				display = <&display0>;
-				status = "okay";
-
-				display0: display0 {
-					bits-per-pixel = <32>;
-					bus-width = <24>;
-
-					display-timings {
-						native-mode = <&timing0>;
-						timing0: timing0 {
-							clock-frequency = <30000000>;
-							hactive = <800>;
-							vactive = <480>;
-							hback-porch = <88>;
-							hfront-porch = <40>;
-							vback-porch = <32>;
-							vfront-porch = <13>;
-							hsync-len = <48>;
-							vsync-len = <3>;
-							hsync-active = <1>;
-							vsync-active = <1>;
-							de-active = <1>;
-							pixelclk-active = <0>;
-						};
-					};
-				};
-			};
-		};
-
-		apbx@80040000 {
-			saif0: saif@80042000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif0_pins_a>;
-				status = "okay";
-			};
-
-			saif1: saif@80046000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&saif1_pins_a>;
-				fsl,saif-master = <&saif0>;
-				status = "okay";
-			};
-
-			i2c0: i2c@80058000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&i2c0_pins_a>;
-				status = "okay";
-
-				sgtl5000: codec@a {
-					compatible = "fsl,sgtl5000";
-					reg = <0x0a>;
-					#sound-dai-cells = <0>;
-					VDDA-supply = <&reg_3p3v>;
-					VDDIO-supply = <&reg_3p3v>;
-					clocks = <&saif0>;
-				};
-
-				pcf8563: rtc@51 {
-					compatible = "phg,pcf8563";
-					reg = <0x51>;
-				};
-			};
-
-			duart: serial@80074000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&duart_pins_a>;
-				status = "okay";
-			};
-
-			auart0: serial@8006a000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart0_pins_a>;
-				status = "okay";
-			};
-
-			auart1: serial@8006c000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart1_2pins_a>;
-				status = "okay";
-			};
-
-			auart2: serial@8006e000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&auart2_2pins_a>;
-				status = "okay";
-			};
-
-			usbphy1: usbphy@8007e000 {
-				pinctrl-names = "default";
-				pinctrl-0 = <&usb1_pins_a>;
-				status = "okay";
-			};
-		};
-	};
-
-	ahb@80080000 {
-		usb1: usb@80090000 {
-		      status = "okay";
-		};
-
-		mac0: ethernet@800f0000 {
-			phy-mode = "rmii";
-			pinctrl-names = "default";
-			pinctrl-0 = <&mac0_pins_a>;
-			status = "okay";
-		};
-	};
-
 	regulators {
 		compatible = "simple-bus";
 		#address-cells = <1>;
@@ -238,3 +44,189 @@
 		};
 	};
 };
+
+&auart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart0_pins_a>;
+	status = "okay";
+};
+
+&auart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart1_2pins_a>;
+	status = "okay";
+};
+
+&auart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&auart2_2pins_a>;
+	status = "okay";
+};
+
+&duart {
+	pinctrl-names = "default";
+	pinctrl-0 = <&duart_pins_a>;
+	status = "okay";
+};
+
+&gpmi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&gpmi_pins_a &gpmi_status_cfg>;
+	status = "okay";
+};
+
+&lcdif {
+	pinctrl-names = "default";
+	pinctrl-0 = <&lcdif_24bit_pins_a
+		     &lcdif_pins_apx4>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <32>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&timing0>;
+			timing0: timing0 {
+				clock-frequency = <30000000>;
+				hactive = <800>;
+				vactive = <480>;
+				hback-porch = <88>;
+				hfront-porch = <40>;
+				vback-porch = <32>;
+				vfront-porch = <13>;
+				hsync-len = <48>;
+				vsync-len = <3>;
+				hsync-active = <1>;
+				vsync-active = <1>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins_a>;
+	status = "okay";
+
+	sgtl5000: codec@a {
+		compatible = "fsl,sgtl5000";
+		reg = <0x0a>;
+		#sound-dai-cells = <0>;
+		VDDA-supply = <&reg_3p3v>;
+		VDDIO-supply = <&reg_3p3v>;
+		clocks = <&saif0>;
+	};
+
+	pcf8563: rtc@51 {
+		compatible = "phg,pcf8563";
+		reg = <0x51>;
+	};
+};
+
+&mac0 {
+	phy-mode = "rmii";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mac0_pins_a>;
+	status = "okay";
+};
+
+&pinctrl {
+	pinctrl-names = "default";
+	pinctrl-0 = <&hog_pins_a>;
+
+	hog_pins_a: hog@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_GPMI_CE1N__GPIO_0_17
+			MX28_PAD_GPMI_RDY1__GPIO_0_21
+			MX28_PAD_SSP2_MISO__GPIO_2_18
+			MX28_PAD_SSP2_SS0__AUART3_TX /* was: 0x2131 - MX28_PAD_SSP2_SS0__GPIO_2_19 */
+			MX28_PAD_PWM3__GPIO_3_28
+			MX28_PAD_LCD_RESET__GPIO_3_30
+			MX28_PAD_JTAG_RTCK__GPIO_4_20
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	lcdif_pins_apx4: lcdif-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_LCD_RD_E__LCD_VSYNC
+			MX28_PAD_LCD_WR_RWN__LCD_HSYNC
+			MX28_PAD_LCD_RS__LCD_DOTCLK
+			MX28_PAD_LCD_CS__LCD_ENABLE
+		>;
+		fsl,drive-strength = <MXS_DRIVE_4mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+
+	mmc2_4bit_pins_apx4: mmc2-4bit-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA4__SSP2_D0
+			MX28_PAD_SSP0_DATA5__SSP2_D3
+			MX28_PAD_SSP0_DATA6__SSP2_CMD
+			MX28_PAD_SSP0_DATA7__SSP2_SCK
+			MX28_PAD_SSP2_SS1__SSP2_D1
+			MX28_PAD_SSP2_SS2__SSP2_D2
+		>;
+		fsl,drive-strength = <MXS_DRIVE_8mA>;
+		fsl,voltage = <MXS_VOLTAGE_HIGH>;
+		fsl,pull-up = <MXS_PULL_ENABLE>;
+	};
+
+	mmc2_sck_cfg_apx4: mmc2-sck-cfg-apx4@0 {
+		reg = <0>;
+		fsl,pinmux-ids = <
+			MX28_PAD_SSP0_DATA7__SSP2_SCK
+		>;
+		fsl,drive-strength = <MXS_DRIVE_12mA>;
+		fsl,pull-up = <MXS_PULL_DISABLE>;
+	};
+};
+
+&saif0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif0_pins_a>;
+	status = "okay";
+};
+
+&saif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&saif1_pins_a>;
+	fsl,saif-master = <&saif0>;
+	status = "okay";
+};
+
+&ssp0 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_sck_cfg>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&ssp2 {
+	compatible = "fsl,imx28-mmc";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_4bit_pins_apx4 &mmc2_sck_cfg_apx4>;
+	bus-width = <4>;
+	status = "okay";
+};
+
+&usb1 {
+      status = "okay";
+};
+
+&usbphy1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&usb1_pins_a>;
+	status = "okay";
+};