Merge branch 'late/kirkwood' into late/soc

Merge in the late Kirkwood branch with the OMAP late branch for upstream
submission.

Final contents described in shared tag.

Fixup remove/change conflicts in arch/arm/mach-omap2/devices.c and
drivers/spi/spi-omap2-mcspi.c.

Signed-off-by: Olof Johansson <olof@lixom.net>

1 files changed, 110 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
new file mode 100644
index 000000000000..548892c08c59
--- /dev/null
+++ b/Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
@@ -0,0 +1,110 @@
+BCM2835 Top-Level ("ARMCTRL") Interrupt Controller
+
+The BCM2835 contains a custom top-level interrupt controller, which supports
+72 interrupt sources using a 2-level register scheme. The interrupt
+controller, or the HW block containing it, is referred to occasionally
+as "armctrl" in the SoC documentation, hence naming of this binding.
+
+Required properties:
+
+- compatible : should be "brcm,bcm2835-armctrl-ic.txt"
+- reg : Specifies base physical address and size of the registers.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 2.
+
+  The 1st cell is the interrupt bank; 0 for interrupts in the "IRQ basic
+  pending" register, or 1/2 respectively for interrupts in the "IRQ pending
+  1/2" register.
+
+  The 2nd cell contains the interrupt number within the bank. Valid values
+  are 0..7 for bank 0, and 0..31 for bank 1.
+
+The interrupt sources are as follows:
+
+Bank 0:
+0: ARM_TIMER
+1: ARM_MAILBOX
+2: ARM_DOORBELL_0
+3: ARM_DOORBELL_1
+4: VPU0_HALTED
+5: VPU1_HALTED
+6: ILLEGAL_TYPE0
+7: ILLEGAL_TYPE1
+
+Bank 1:
+0: TIMER0
+1: TIMER1
+2: TIMER2
+3: TIMER3
+4: CODEC0
+5: CODEC1
+6: CODEC2
+7: VC_JPEG
+8: ISP
+9: VC_USB
+10: VC_3D
+11: TRANSPOSER
+12: MULTICORESYNC0
+13: MULTICORESYNC1
+14: MULTICORESYNC2
+15: MULTICORESYNC3
+16: DMA0
+17: DMA1
+18: VC_DMA2
+19: VC_DMA3
+20: DMA4
+21: DMA5
+22: DMA6
+23: DMA7
+24: DMA8
+25: DMA9
+26: DMA10
+27: DMA11
+28: DMA12
+29: AUX
+30: ARM
+31: VPUDMA
+
+Bank 2:
+0: HOSTPORT
+1: VIDEOSCALER
+2: CCP2TX
+3: SDC
+4: DSI0
+5: AVE
+6: CAM0
+7: CAM1
+8: HDMI0
+9: HDMI1
+10: PIXELVALVE1
+11: I2CSPISLV
+12: DSI1
+13: PWA0
+14: PWA1
+15: CPR
+16: SMI
+17: GPIO0
+18: GPIO1
+19: GPIO2
+20: GPIO3
+21: VC_I2C
+22: VC_SPI
+23: VC_I2SPCM
+24: VC_SDIO
+25: VC_UART
+26: SLIMBUS
+27: VEC
+28: CPG
+29: RNG
+30: VC_ARASANSDIO
+31: AVSPMON
+
+Example:
+
+intc: interrupt-controller {
+	compatible = "brcm,bcm2835-armctrl-ic";
+	reg = <0x7e00b200 0x200>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+};