Merge tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull ARM SoC devicetree updates from Arnd Bergmann:
 "The biggest change this time is for the 32-bit devicetree files, which
  are all moved to a new location, using separate subdirectories for
  each SoC vendor, following the same scheme that is used on arm64, mips
  and riscv. This has been discussed for many years, but so far we never
  did this as there was a plan to move the files out of the kernel
  entirely, which has never happened.

  The impact of this will be that all external patches no longer apply,
  and anything depending on the location of the dtb files in the build
  directory will have to change. The installed files after 'make
  dtbs_install' keep the current location.

  There are six added SoCs here that are largely variants of previously
  added chips. Two other chips are added in a separate branch along with
  their device drivers.

   - The Samsung Exynos 4212 makes its return after the Samsung Galaxy
     Express phone is addded at last. The SoC support was originally
     added in 2012 but removed again in 2017 as it was unused at the
     time.

   - Amlogic C3 is a Cortex-A35 based smart IP camera chip

   - Qualcomm MSM8939 (Snapdragon 615) is a more featureful variant of
     the still common MSM8916 (Snapdragon 410) phone chip that has been
     supported for a long time.

   - Qualcomm SC8180x (Snapdragon 8cx) is one of their earlier high-end
     laptop chips, used in the Lenovo Flex 5G, which is added along with
     the reference board.

   - Qualcomm SDX75 is the latest generation modem chip that is used as
     a peripherial in phones but can also run a standalone Linux. Unlike
     the prior 32-bit SDX65 and SDX55, this now has a 64-bit Cortex-A55.

   - Alibaba T-Head TH1520 is a quad-core RISC-V chip based on the
     Xuantie C910 core, a step up from all previously added rv64 chips.

  All of the above come with reference board implementations, those
  included there are 39 new board files, but only five more 32-bit this
  time, probably a new low:

   - Marantec Maveo board based on dhcor imx6ull module

   - Endian 4i Edge 200, based on the armv5 Marvell Kirkwood chip

   - Epson Moverio BT-200 AR glasses based on TI OMAP4

   - PHYTEC STM32MP1-3 Dev board based on STM32MP15 PHYTEC SOM

   - ICnova ADB4006 board based on Allwinner A20

  On the 64-bit side, there are also fewer addded machines than we had
  in the recent releases:

   - Three boards based on NXP i.MX8: Emtop SoM & Baseboard, NXP i.MX8MM
     EVKB board and i.MX8MP based Gateworks Venice gw7905-2x device.

   - NVIDIA IGX Orin and Jetson Orin Nano boards, both based on tegra234

   - Qualcomm gains support for 6 reference boards on various members of
     their IPQ networking SoC series, as well as the Sony Xperia M4 Aqua
     phone, the Acer Aspire 1 laptop, and the Fxtec Pro1X board on top
     of the various reference platforms for their new chips.

   - Rockchips support for several newer boards: Indiedroid Nova
     (rk3588), Edgeble Neural Compute Module 6B (rk3588), FriendlyARM
     NanoPi R2C Plus (rk3328), Anbernic RG353PS (rk3566), Lunzn
     Fastrhino R66S/R68S (rk3568)

   - TI K3/AM625 based PHYTEC phyBOARD-Lyra-AM625 board and Toradex
     Verdin family with AM62 COM, carrier and dev boards

  Other changes to existing boards contain the usual minor improvements
  along with

   - continued updates to clean up dts files based on dtc warnings and
     binding checks, in particular cache properties and node names

   - support for devicetree overlays on at91, bcm283x

   - significant additions to existing SoC support on mediatek,
     qualcomm, ti k3 family, starfive jh71xx, NXP i.MX6 and i.MX8, ST
     STM32MP1

  As usual, a lot more detail is available in the individual merge
  commits"

* tag 'soc-dt-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (926 commits)
  ARM: mvebu: fix unit address on armada-390-db flash
  ARM: dts: Move .dts files to vendor sub-directories
  kbuild: Support flat DTBs install
  ARM: dts: Add .dts files missing from the build
  ARM: dts: allwinner: Use quoted #include
  ARM: dts: lan966x: kontron-d10: add PHY interrupts
  ARM: dts: lan966x: kontron-d10: fix SPI CS
  ARM: dts: lan966x: kontron-d10: fix board reset
  ARM: dts: at91: Enable device-tree overlay support for AT91 boards
  arm: dts: Enable device-tree overlay support for AT91 boards
  arm64: dts: exynos: Remove clock from Exynos850 pmu_system_controller
  ARM: dts: at91: use generic name for shutdown controller
  ARM: dts: BCM5301X: Add cells sizes to PCIe nodes
  dt-bindings: firmware: brcm,kona-smc: convert to YAML
  riscv: dts: sort makefile entries by directory
  riscv: defconfig: enable T-HEAD SoC
  MAINTAINERS: add entry for T-HEAD RISC-V SoC
  riscv: dts: thead: add sipeed Lichee Pi 4A board device tree
  riscv: dts: add initial T-HEAD TH1520 SoC device tree
  riscv: Add the T-HEAD SoC family Kconfig option
  ...

1 files changed, 855 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/allwinner/sun8i-a23-a33.dtsi b/arch/arm/boot/dts/allwinner/sun8i-a23-a33.dtsi
new file mode 100644
index 000000000000..cd4bf60dbb3c
--- /dev/null
+++ b/arch/arm/boot/dts/allwinner/sun8i-a23-a33.dtsi
@@ -0,0 +1,855 @@
+/*
+ * Copyright 2014 Chen-Yu Tsai
+ *
+ * Chen-Yu Tsai <wens@csie.org>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+
+#include <dt-bindings/clock/sun6i-rtc.h>
+#include <dt-bindings/clock/sun8i-a23-a33-ccu.h>
+#include <dt-bindings/reset/sun8i-a23-a33-ccu.h>
+
+/ {
+	interrupt-parent = <&gic>;
+	#address-cells = <1>;
+	#size-cells = <1>;
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		simplefb_lcd: framebuffer-lcd0 {
+			compatible = "allwinner,simple-framebuffer",
+				     "simple-framebuffer";
+			allwinner,pipeline = "de_be0-lcd0";
+			clocks = <&ccu CLK_BUS_LCD>, <&ccu CLK_BUS_DE_BE>,
+				 <&ccu CLK_LCD_CH0>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_DRAM_DE_BE>, <&ccu CLK_DRC>;
+			status = "disabled";
+		};
+	};
+
+	de: display-engine {
+		/* compatible gets set in SoC specific dtsi file */
+		allwinner,pipelines = <&fe0>;
+		status = "disabled";
+	};
+
+	timer {
+		compatible = "arm,armv7-timer";
+		interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+			     <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+		clock-frequency = <24000000>;
+		arm,cpu-registers-not-fw-configured;
+	};
+
+	cpus {
+		enable-method = "allwinner,sun8i-a23";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu0: cpu@0 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <0>;
+		};
+
+		cpu@1 {
+			compatible = "arm,cortex-a7";
+			device_type = "cpu";
+			reg = <1>;
+		};
+	};
+
+	clocks {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		osc24M: osc24M_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <24000000>;
+			clock-accuracy = <50000>;
+			clock-output-names = "osc24M";
+		};
+
+		ext_osc32k: ext_osc32k_clk {
+			#clock-cells = <0>;
+			compatible = "fixed-clock";
+			clock-frequency = <32768>;
+			clock-accuracy = <50000>;
+			clock-output-names = "ext-osc32k";
+		};
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		system-control@1c00000 {
+			compatible = "allwinner,sun8i-a23-system-control";
+			reg = <0x01c00000 0x30>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+			ranges;
+
+			sram_c: sram@1d00000 {
+				compatible = "mmio-sram";
+				reg = <0x01d00000 0x80000>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0 0x01d00000 0x80000>;
+
+				ve_sram: sram-section@0 {
+					compatible = "allwinner,sun8i-a23-sram-c1",
+						     "allwinner,sun4i-a10-sram-c1";
+					reg = <0x000000 0x80000>;
+				};
+			};
+		};
+
+		dma: dma-controller@1c02000 {
+			compatible = "allwinner,sun8i-a23-dma";
+			reg = <0x01c02000 0x1000>;
+			interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DMA>;
+			resets = <&ccu RST_BUS_DMA>;
+			#dma-cells = <1>;
+		};
+
+		nfc: nand-controller@1c03000 {
+			compatible = "allwinner,sun8i-a23-nand-controller";
+			reg = <0x01c03000 0x1000>;
+			interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_NAND>, <&ccu CLK_NAND>;
+			clock-names = "ahb", "mod";
+			resets = <&ccu RST_BUS_NAND>;
+			reset-names = "ahb";
+			dmas = <&dma 5>;
+			dma-names = "rxtx";
+			pinctrl-names = "default";
+			pinctrl-0 = <&nand_pins &nand_cs0_pin &nand_rb0_pin>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		tcon0: lcd-controller@1c0c000 {
+			/* compatible gets set in SoC specific dtsi file */
+			reg = <0x01c0c000 0x1000>;
+			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
+			dmas = <&dma 12>;
+			clocks = <&ccu CLK_BUS_LCD>,
+				 <&ccu CLK_LCD_CH0>,
+				 <&ccu 13>;
+			clock-names = "ahb",
+				      "tcon-ch0",
+				      "lvds-alt";
+			clock-output-names = "tcon-data-clock";
+			#clock-cells = <0>;
+			resets = <&ccu RST_BUS_LCD>,
+				 <&ccu RST_BUS_LVDS>;
+			reset-names = "lcd",
+				      "lvds";
+			status = "disabled";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				tcon0_in: port@0 {
+					reg = <0>;
+
+					tcon0_in_drc0: endpoint {
+						remote-endpoint = <&drc0_out_tcon0>;
+					};
+				};
+
+				tcon0_out: port@1 {
+					reg = <1>;
+				};
+			};
+		};
+
+		mmc0: mmc@1c0f000 {
+			compatible = "allwinner,sun7i-a20-mmc";
+			reg = <0x01c0f000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC0>,
+				 <&ccu CLK_MMC0>,
+				 <&ccu CLK_MMC0_OUTPUT>,
+				 <&ccu CLK_MMC0_SAMPLE>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ccu RST_BUS_MMC0>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&mmc0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc1: mmc@1c10000 {
+			compatible = "allwinner,sun7i-a20-mmc";
+			reg = <0x01c10000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC1>,
+				 <&ccu CLK_MMC1>,
+				 <&ccu CLK_MMC1_OUTPUT>,
+				 <&ccu CLK_MMC1_SAMPLE>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ccu RST_BUS_MMC1>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mmc2: mmc@1c11000 {
+			compatible = "allwinner,sun7i-a20-mmc";
+			reg = <0x01c11000 0x1000>;
+			clocks = <&ccu CLK_BUS_MMC2>,
+				 <&ccu CLK_MMC2>,
+				 <&ccu CLK_MMC2_OUTPUT>,
+				 <&ccu CLK_MMC2_SAMPLE>;
+			clock-names = "ahb",
+				      "mmc",
+				      "output",
+				      "sample";
+			resets = <&ccu RST_BUS_MMC2>;
+			reset-names = "ahb";
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		usb_otg: usb@1c19000 {
+			/* compatible gets set in SoC specific dtsi file */
+			reg = <0x01c19000 0x0400>;
+			clocks = <&ccu CLK_BUS_OTG>;
+			resets = <&ccu RST_BUS_OTG>;
+			interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "mc";
+			phys = <&usbphy 0>;
+			phy-names = "usb";
+			extcon = <&usbphy 0>;
+			dr_mode = "otg";
+			status = "disabled";
+		};
+
+		usbphy: phy@1c19400 {
+			/*
+			 * compatible and address regions get set in
+			 * SoC specific dtsi file
+			 */
+			clocks = <&ccu CLK_USB_PHY0>,
+				 <&ccu CLK_USB_PHY1>;
+			clock-names = "usb0_phy",
+				      "usb1_phy";
+			resets = <&ccu RST_USB_PHY0>,
+				 <&ccu RST_USB_PHY1>;
+			reset-names = "usb0_reset",
+				      "usb1_reset";
+			status = "disabled";
+			#phy-cells = <1>;
+		};
+
+		ehci0: usb@1c1a000 {
+			compatible = "allwinner,sun8i-a23-ehci", "generic-ehci";
+			reg = <0x01c1a000 0x100>;
+			interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_EHCI>;
+			resets = <&ccu RST_BUS_EHCI>;
+			phys = <&usbphy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci0: usb@1c1a400 {
+			compatible = "allwinner,sun8i-a23-ohci", "generic-ohci";
+			reg = <0x01c1a400 0x100>;
+			interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_OHCI>, <&ccu CLK_USB_OHCI>;
+			resets = <&ccu RST_BUS_OHCI>;
+			phys = <&usbphy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ccu: clock@1c20000 {
+			reg = <0x01c20000 0x400>;
+			clocks = <&osc24M>, <&rtc CLK_OSC32K>;
+			clock-names = "hosc", "losc";
+			#clock-cells = <1>;
+			#reset-cells = <1>;
+		};
+
+		pio: pinctrl@1c20800 {
+			/* compatible gets set in SoC specific dtsi file */
+			reg = <0x01c20800 0x400>;
+			interrupt-parent = <&r_intc>;
+			/* interrupts get set in SoC specific dtsi file */
+			clocks = <&ccu CLK_BUS_PIO>, <&osc24M>,
+				 <&rtc CLK_OSC32K>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#gpio-cells = <3>;
+
+			i2c0_pins: i2c0-pins {
+				pins = "PH2", "PH3";
+				function = "i2c0";
+			};
+
+			i2c1_pins: i2c1-pins {
+				pins = "PH4", "PH5";
+				function = "i2c1";
+			};
+
+			i2c2_pins: i2c2-pins {
+				pins = "PE12", "PE13";
+				function = "i2c2";
+			};
+
+			lcd_rgb666_pins: lcd-rgb666-pins {
+				pins = "PD2", "PD3", "PD4", "PD5", "PD6", "PD7",
+				       "PD10", "PD11", "PD12", "PD13", "PD14", "PD15",
+				       "PD18", "PD19", "PD20", "PD21", "PD22", "PD23",
+				       "PD24", "PD25", "PD26", "PD27";
+				function = "lcd0";
+			};
+
+			mmc0_pins: mmc0-pins {
+				pins = "PF0", "PF1", "PF2",
+				       "PF3", "PF4", "PF5";
+				function = "mmc0";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc1_pg_pins: mmc1-pg-pins {
+				pins = "PG0", "PG1", "PG2",
+				       "PG3", "PG4", "PG5";
+				function = "mmc1";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			mmc2_8bit_pins: mmc2-8bit-pins {
+				pins = "PC5", "PC6", "PC8",
+				       "PC9", "PC10", "PC11",
+				       "PC12", "PC13", "PC14",
+				       "PC15", "PC16";
+				function = "mmc2";
+				drive-strength = <30>;
+				bias-pull-up;
+			};
+
+			nand_pins: nand-pins {
+				pins = "PC0", "PC1", "PC2", "PC5",
+				       "PC8", "PC9", "PC10", "PC11",
+				       "PC12", "PC13", "PC14", "PC15";
+				function = "nand0";
+			};
+
+			nand_cs0_pin: nand-cs0-pin {
+				pins = "PC4";
+				function = "nand0";
+				bias-pull-up;
+			};
+
+			nand_cs1_pin: nand-cs1-pin {
+				pins = "PC3";
+				function = "nand0";
+				bias-pull-up;
+			};
+
+			nand_rb0_pin: nand-rb0-pin {
+				pins = "PC6";
+				function = "nand0";
+				bias-pull-up;
+			};
+
+			nand_rb1_pin: nand-rb1-pin {
+				pins = "PC7";
+				function = "nand0";
+				bias-pull-up;
+			};
+
+			pwm0_pin: pwm0-pin {
+				pins = "PH0";
+				function = "pwm0";
+			};
+
+			uart0_pf_pins: uart0-pf-pins {
+				pins = "PF2", "PF4";
+				function = "uart0";
+			};
+
+			uart1_pg_pins: uart1-pg-pins {
+				pins = "PG6", "PG7";
+				function = "uart1";
+			};
+
+			uart1_cts_rts_pg_pins: uart1-cts-rts-pg-pins {
+				pins = "PG8", "PG9";
+				function = "uart1";
+			};
+		};
+
+		timer@1c20c00 {
+			compatible = "allwinner,sun8i-a23-timer";
+			reg = <0x01c20c00 0xa0>;
+			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
+		wdt0: watchdog@1c20ca0 {
+			compatible = "allwinner,sun6i-a31-wdt";
+			reg = <0x01c20ca0 0x20>;
+			interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&osc24M>;
+		};
+
+		pwm: pwm@1c21400 {
+			compatible = "allwinner,sun7i-a20-pwm";
+			reg = <0x01c21400 0xc>;
+			clocks = <&osc24M>;
+			#pwm-cells = <3>;
+			status = "disabled";
+		};
+
+		lradc: lradc@1c22800 {
+			compatible = "allwinner,sun4i-a10-lradc-keys";
+			reg = <0x01c22800 0x100>;
+			interrupt-parent = <&r_intc>;
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			status = "disabled";
+		};
+
+		uart0: serial@1c28000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28000 0x400>;
+			interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART0>;
+			resets = <&ccu RST_BUS_UART0>;
+			dmas = <&dma 6>, <&dma 6>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart1: serial@1c28400 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28400 0x400>;
+			interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART1>;
+			resets = <&ccu RST_BUS_UART1>;
+			dmas = <&dma 7>, <&dma 7>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart2: serial@1c28800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28800 0x400>;
+			interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART2>;
+			resets = <&ccu RST_BUS_UART2>;
+			dmas = <&dma 8>, <&dma 8>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart3: serial@1c28c00 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c28c00 0x400>;
+			interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART3>;
+			resets = <&ccu RST_BUS_UART3>;
+			dmas = <&dma 9>, <&dma 9>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		uart4: serial@1c29000 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01c29000 0x400>;
+			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&ccu CLK_BUS_UART4>;
+			resets = <&ccu RST_BUS_UART4>;
+			dmas = <&dma 10>, <&dma 10>;
+			dma-names = "tx", "rx";
+			status = "disabled";
+		};
+
+		i2c0: i2c@1c2ac00 {
+			compatible = "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2ac00 0x400>;
+			interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C0>;
+			resets = <&ccu RST_BUS_I2C0>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c0_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c1: i2c@1c2b000 {
+			compatible = "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2b000 0x400>;
+			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C1>;
+			resets = <&ccu RST_BUS_I2C1>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c1_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		i2c2: i2c@1c2b400 {
+			compatible = "allwinner,sun6i-a31-i2c";
+			reg = <0x01c2b400 0x400>;
+			interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_I2C2>;
+			resets = <&ccu RST_BUS_I2C2>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&i2c2_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		mali: gpu@1c40000 {
+			compatible = "allwinner,sun8i-a23-mali",
+				     "allwinner,sun7i-a20-mali", "arm,mali-400";
+			reg = <0x01c40000 0x10000>;
+			interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "gp",
+					  "gpmmu",
+					  "pp0",
+					  "ppmmu0",
+					  "pp1",
+					  "ppmmu1",
+					  "pmu";
+			clocks = <&ccu CLK_BUS_GPU>, <&ccu CLK_GPU>;
+			clock-names = "bus", "core";
+			resets = <&ccu RST_BUS_GPU>;
+			#cooling-cells = <2>;
+
+			assigned-clocks = <&ccu CLK_GPU>;
+			assigned-clock-rates = <384000000>;
+		};
+
+		gic: interrupt-controller@1c81000 {
+			compatible = "arm,gic-400";
+			reg = <0x01c81000 0x1000>,
+			      <0x01c82000 0x2000>,
+			      <0x01c84000 0x2000>,
+			      <0x01c86000 0x2000>;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+		};
+
+		fe0: display-frontend@1e00000 {
+			/* compatible gets set in SoC specific dtsi file */
+			reg = <0x01e00000 0x20000>;
+			interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DE_FE>, <&ccu CLK_DE_FE>,
+				 <&ccu CLK_DRAM_DE_FE>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&ccu RST_BUS_DE_FE>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				fe0_out: port@1 {
+					reg = <1>;
+
+					fe0_out_be0: endpoint {
+						remote-endpoint = <&be0_in_fe0>;
+					};
+				};
+			};
+		};
+
+		be0: display-backend@1e60000 {
+			/* compatible gets set in SoC specific dtsi file */
+			reg = <0x01e60000 0x10000>;
+			interrupts = <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DE_BE>, <&ccu CLK_DE_BE>,
+				 <&ccu CLK_DRAM_DE_BE>;
+			clock-names = "ahb", "mod",
+				      "ram";
+			resets = <&ccu RST_BUS_DE_BE>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				be0_in: port@0 {
+					reg = <0>;
+
+					be0_in_fe0: endpoint {
+						remote-endpoint = <&fe0_out_be0>;
+					};
+				};
+
+				be0_out: port@1 {
+					reg = <1>;
+
+					be0_out_drc0: endpoint {
+						remote-endpoint = <&drc0_in_be0>;
+					};
+				};
+			};
+		};
+
+		drc0: drc@1e70000 {
+			/* compatible gets set in SoC specific dtsi file */
+			reg = <0x01e70000 0x10000>;
+			interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_DRC>, <&ccu CLK_DRC>,
+				 <&ccu CLK_DRAM_DRC>;
+			clock-names = "ahb", "mod", "ram";
+			resets = <&ccu RST_BUS_DRC>;
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				drc0_in: port@0 {
+					reg = <0>;
+
+					drc0_in_be0: endpoint {
+						remote-endpoint = <&be0_out_drc0>;
+					};
+				};
+
+				drc0_out: port@1 {
+					reg = <1>;
+
+					drc0_out_tcon0: endpoint {
+						remote-endpoint = <&tcon0_in_drc0>;
+					};
+				};
+			};
+		};
+
+		rtc: rtc@1f00000 {
+			compatible = "allwinner,sun8i-a23-rtc";
+			reg = <0x01f00000 0x400>;
+			interrupt-parent = <&r_intc>;
+			interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+				     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+			clock-output-names = "osc32k", "osc32k-out";
+			clocks = <&ext_osc32k>;
+			#clock-cells = <1>;
+		};
+
+		r_intc: interrupt-controller@1f00c00 {
+			compatible = "allwinner,sun6i-a31-r-intc";
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			reg = <0x01f00c00 0x400>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		};
+
+		prcm@1f01400 {
+			compatible = "allwinner,sun8i-a23-prcm";
+			reg = <0x01f01400 0x200>;
+
+			ar100: ar100_clk {
+				compatible = "fixed-factor-clock";
+				#clock-cells = <0>;
+				clock-div = <1>;
+				clock-mult = <1>;
+				clocks = <&osc24M>;
+				clock-output-names = "ar100";
+			};
+
+			ahb0: ahb0_clk {
+				compatible = "fixed-factor-clock";
+				#clock-cells = <0>;
+				clock-div = <1>;
+				clock-mult = <1>;
+				clocks = <&ar100>;
+				clock-output-names = "ahb0";
+			};
+
+			apb0: apb0_clk {
+				compatible = "allwinner,sun8i-a23-apb0-clk";
+				#clock-cells = <0>;
+				clocks = <&ahb0>;
+				clock-output-names = "apb0";
+			};
+
+			apb0_gates: apb0_gates_clk {
+				compatible = "allwinner,sun8i-a23-apb0-gates-clk";
+				#clock-cells = <1>;
+				clocks = <&apb0>;
+				clock-output-names = "apb0_pio", "apb0_timer",
+						"apb0_rsb", "apb0_uart",
+						"apb0_i2c";
+			};
+
+			apb0_rst: apb0_rst {
+				compatible = "allwinner,sun6i-a31-clock-reset";
+				#reset-cells = <1>;
+			};
+
+			codec_analog: codec-analog {
+				compatible = "allwinner,sun8i-a23-codec-analog";
+			};
+		};
+
+		cpucfg@1f01c00 {
+			compatible = "allwinner,sun8i-a23-cpuconfig";
+			reg = <0x01f01c00 0x300>;
+		};
+
+		r_uart: serial@1f02800 {
+			compatible = "snps,dw-apb-uart";
+			reg = <0x01f02800 0x400>;
+			interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
+			reg-shift = <2>;
+			reg-io-width = <4>;
+			clocks = <&apb0_gates 4>;
+			resets = <&apb0_rst 4>;
+			status = "disabled";
+		};
+
+		r_i2c: i2c@1f02400 {
+			compatible = "allwinner,sun8i-a23-i2c",
+				     "allwinner,sun6i-a31-i2c";
+			reg = <0x01f02400 0x400>;
+			interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_i2c_pins>;
+			clocks = <&apb0_gates 6>;
+			resets = <&apb0_rst 6>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		r_pio: pinctrl@1f02c00 {
+			compatible = "allwinner,sun8i-a23-r-pinctrl";
+			reg = <0x01f02c00 0x400>;
+			interrupt-parent = <&r_intc>;
+			interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&apb0_gates 0>, <&osc24M>, <&rtc CLK_OSC32K>;
+			clock-names = "apb", "hosc", "losc";
+			gpio-controller;
+			interrupt-controller;
+			#interrupt-cells = <3>;
+			#gpio-cells = <3>;
+
+			r_i2c_pins: r-i2c-pins {
+				pins = "PL0", "PL1";
+				function = "s_i2c";
+				bias-pull-up;
+			};
+
+			r_rsb_pins: r-rsb-pins {
+				pins = "PL0", "PL1";
+				function = "s_rsb";
+				drive-strength = <20>;
+				bias-pull-up;
+			};
+
+			r_uart_pins_a: r-uart-pins {
+				pins = "PL2", "PL3";
+				function = "s_uart";
+			};
+		};
+
+		r_rsb: rsb@1f03400 {
+			compatible = "allwinner,sun8i-a23-rsb";
+			reg = <0x01f03400 0x400>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&apb0_gates 3>;
+			clock-frequency = <3000000>;
+			resets = <&apb0_rst 3>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&r_rsb_pins>;
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+	};
+};