ARM: dts: Add support for sbc-3xxx with cm-t3730

This adds support for CompuLab SBC-T3530, also known as cm-t3730:

http://compulab.co.il/products/sbcs/sbc-t3530/

It seems that with the sbc-3xxx mainboard is also used on
SBC-T3517 and SBC-T3730 with just a different CPU module:

http://compulab.co.il/products/sbcs/sbc-t3517/
http://compulab.co.il/products/sbcs/sbc-t3730/

So let's add a common omap3-sb-t35.dtsi and then separate SoC
specific omap3-sbc-t3730.dts, omap3-sbc-t3530.dts and
omap3-sbc-t3517.dts.

I've tested this with SBC-T3730 as that's the only one I have.
At least serial, both Ethernet controllers, MMC, and wl12xx WLAN
work.

Note that WLAN seems to be different for SBC-T3530. And SBC-T3517
may need some changes for the EMAC Ethernet if that's used
instead of the smsc911x.

Cc: devicetree@vger.kernel.org
Cc: Mike Rapoport <mike@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>

5 files changed, 271 insertions, 0 deletions

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index fc37bca0ccd3..b7af5023dc89 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -179,6 +179,8 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \
 	omap2420-n810-wimax.dtb \
 	omap3430-sdp.dtb \
 	omap3-beagle.dtb \
+	omap3-cm-t3730.dtb \
+	omap3-sbc-t3730.dtb \
 	omap3-devkit8000.dtb \
 	omap3-beagle-xm.dtb \
 	omap3-evm.dtb \
diff --git a/arch/arm/boot/dts/omap3-cm-t3730.dts b/arch/arm/boot/dts/omap3-cm-t3730.dts
new file mode 100644
index 000000000000..486f4d6c4219
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-cm-t3730.dts
@@ -0,0 +1,104 @@
+/*
+ * Support for CompuLab CM-T3730
+ */
+/dts-v1/;
+
+#include "omap36xx.dtsi"
+#include "omap3-cm-t3x30.dtsi"
+
+/ {
+	model = "CompuLab CM-T3730";
+	compatible = "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3";
+
+	wl12xx_vmmc2: wl12xx_vmmc2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vw1271";
+		pinctrl-names = "default";
+		pinctrl-0 = <&wl12xx_gpio>;
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		gpio = <&gpio3 9 GPIO_ACTIVE_HIGH>;   /* gpio73 */
+		startup-delay-us = <20000>;
+		enable-active-high;
+	};
+
+	wl12xx_vaux2: wl12xx_vaux2 {
+		compatible = "regulator-fixed";
+		regulator-name = "vwl1271_vaux2";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		vin-supply = <&vaux2>;
+	};
+};
+
+&omap3_pmx_core {
+	mmc1_pins: pinmux_mmc1_pins {
+		pinctrl-single,pins = <
+			0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0)	/* sdmmc1_clk.sdmmc1_clk */
+			0x116 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc1_cmd.sdmmc1_cmd */
+			0x118 (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat0.sdmmc1_dat0 */
+			0x11a (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat1.sdmmc1_dat1 */
+			0x11c (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat2.sdmmc1_dat2 */
+			0x11e (PIN_INPUT_PULLUP | MUX_MODE0) 	/* sdmmc1_dat3.sdmmc1_dat3 */
+		>;
+	};
+
+	mmc2_pins: pinmux_mmc2_pins {
+		pinctrl-single,pins = <
+			0x128 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_clk.sdmmc2_clk */
+			0x12a (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_cmd.sdmmc2_cmd */
+			0x12c (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat0.sdmmc2_dat0 */
+			0x12e (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat1.sdmmc2_dat1 */
+			0x130 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat2.sdmmc2_dat2 */
+			0x132 (PIN_INPUT_PULLUP | MUX_MODE0)	/* sdmmc2_dat3.sdmmc2_dat3 */
+		>;
+	};
+
+	smsc1_pins: pinmux_smsc1_pins {
+		pinctrl-single,pins = <
+			0x88 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs5.gpmc_ncs5 */
+			0x16a (PIN_INPUT_PULLUP | MUX_MODE4)	/* uart3_cts_rctx.gpio_163 */
+		>;
+	};
+
+	uart3_pins: pinmux_uart3_pins {
+		pinctrl-single,pins = <
+			0x16e (PIN_INPUT | MUX_MODE0)		/* uart3_rx_irrx.uart3_rx_irrx */
+			0x170 (PIN_OUTPUT | MUX_MODE0)		/* uart3_tx_irtx.uart3_tx_irtx */
+		>;
+	};
+
+	wl12xx_gpio: pinmux_wl12xx_gpio {
+		pinctrl-single,pins = <
+			0xb2 (PIN_OUTPUT | MUX_MODE4)		/* dss_data3.gpio_73 */
+			0x134 (PIN_INPUT | MUX_MODE4)		/* sdmmc2_dat4.gpio_136 */
+		>;
+	};
+};
+
+&mmc1 {
+	vmmc-supply = <&vmmc1>;
+	bus-width = <4>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc1_pins>;
+};
+
+&mmc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc2_pins>;
+	vmmc-supply = <&wl12xx_vmmc2>;
+	vmmc_aux-supply = <&wl12xx_vaux2>;
+	non-removable;
+	bus-width = <4>;
+	cap-power-off-card;
+};
+
+&smsc1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smsc1_pins>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+};
diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
new file mode 100644
index 000000000000..3a9f004d8924
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi
@@ -0,0 +1,95 @@
+/*
+ * Common support for CompuLab CM-T3530 and  CM-T3730
+ */
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x80000000 0x10000000>; /* 256 MB */
+	};
+
+	cpus {
+		cpu@0 {
+			cpu0-supply = <&vcc>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		ledb {
+			label = "cm-t35:green";
+			gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>;  /* gpio186 */
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
+	vddvario: regulator-vddvario {
+		compatible = "regulator-fixed";
+		regulator-name = "vddvario";
+		regulator-always-on;
+	};
+
+	vdd33a: regulator-vdd33a {
+		compatible = "regulator-fixed";
+		regulator-name = "vdd33a";
+		regulator-always-on;
+	};
+};
+
+&gpmc {
+	ranges = <5 0 0x2c000000 0x01000000>;
+
+	smsc1: ethernet@5,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		interrupt-parent = <&gpio6>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+		reg = <5 0 0xff>;
+		bank-width = <2>;
+		gpmc,mux-add-data;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		vddvario-supply = <&vddvario>;
+		vdd33a-supply = <&vdd33a>;
+		reg-io-width = <4>;
+		smsc,save-mac-address;
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+
+	twl: twl@48 {
+		reg = <0x48>;
+		interrupts = <7>; /* SYS_NIRQ cascaded to intc */
+		interrupt-parent = <&intc>;
+	};
+};
+
+#include "twl4030.dtsi"
+#include "twl4030_omap3.dtsi"
+
+&i2c3 {
+	clock-frequency = <400000>;
+};
+
+&twl_gpio {
+	ti,use-leds;
+};
diff --git a/arch/arm/boot/dts/omap3-sb-t35.dtsi b/arch/arm/boot/dts/omap3-sb-t35.dtsi
new file mode 100644
index 000000000000..b9a2fedce7ee
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-sb-t35.dtsi
@@ -0,0 +1,40 @@
+/*
+ * Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730
+ */
+
+&gpmc {
+	ranges = <4 0 0x2d000000 0x01000000>;
+
+	smsc2: ethernet@4,0 {
+		compatible = "smsc,lan9221", "smsc,lan9115";
+		interrupt-parent = <&gpio3>;
+		interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+		reg = <4 0 0xff>;
+		bank-width = <2>;
+		gpmc,mux-add-data;
+		gpmc,cs-on-ns = <0>;
+		gpmc,cs-rd-off-ns = <186>;
+		gpmc,cs-wr-off-ns = <186>;
+		gpmc,adv-on-ns = <12>;
+		gpmc,adv-rd-off-ns = <48>;
+		gpmc,adv-wr-off-ns = <48>;
+		gpmc,oe-on-ns = <54>;
+		gpmc,oe-off-ns = <168>;
+		gpmc,we-on-ns = <54>;
+		gpmc,we-off-ns = <168>;
+		gpmc,rd-cycle-ns = <186>;
+		gpmc,wr-cycle-ns = <186>;
+		gpmc,access-ns = <114>;
+		gpmc,page-burst-access-ns = <6>;
+		gpmc,bus-turnaround-ns = <12>;
+		gpmc,cycle2cycle-delay-ns = <18>;
+		gpmc,wr-data-mux-bus-ns = <90>;
+		gpmc,wr-access-ns = <186>;
+		gpmc,cycle2cycle-samecsen;
+		gpmc,cycle2cycle-diffcsen;
+		vddvario-supply = <&vddvario>;
+		vdd33a-supply = <&vdd33a>;
+		reg-io-width = <4>;
+		smsc,save-mac-address;
+	};
+};
diff --git a/arch/arm/boot/dts/omap3-sbc-t3730.dts b/arch/arm/boot/dts/omap3-sbc-t3730.dts
new file mode 100644
index 000000000000..c119bd545053
--- /dev/null
+++ b/arch/arm/boot/dts/omap3-sbc-t3730.dts
@@ -0,0 +1,30 @@
+/*
+ * Suppport for CompuLab SBC-T3730 with CM-T3730
+ */
+
+#include "omap3-cm-t3730.dts"
+#include "omap3-sb-t35.dtsi"
+
+/ {
+	model = "CompuLab SBC-T3730 with CM-T3730";
+	compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3";
+};
+
+&gpmc {
+	ranges = <5 0 0x2c000000 0x01000000>,
+		 <4 0 0x2d000000 0x01000000>;
+};
+
+&smsc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&smsc2_pins>;
+};
+
+&omap3_pmx_core {
+	smsc2_pins: pinmux_smsc2_pins {
+		pinctrl-single,pins = <
+			0x86 (PIN_OUTPUT | MUX_MODE0)		/* gpmc_ncs4.gpmc_ncs4 */
+			0xa2 (PIN_INPUT_PULLUP | MUX_MODE4)	/* gpmc_wait3.gpio_65 */
+		>;
+	};
+};
\ No newline at end of file