powerpc/64s: Remove MSR_RI optimisation in system_call_exit()

Currently in system_call_exit() we have an optimisation where we
disable MSR_RI (recoverable interrupt) and MSR_EE (external interrupt
enable) in a single mtmsrd instruction.

Unfortunately this will no longer work with THREAD_INFO_IN_TASK,
because then the load of TI_FLAGS might fault and faulting with MSR_RI
clear is treated as an unrecoverable exception which leads to a
panic().

So change the code to only clear MSR_EE prior to loading TI_FLAGS,
leaving the clear of MSR_RI until later. We have some latitude in
where do the clear of MSR_RI. A bit of experimentation has shown that
this location gives the least slow down.

This still causes a noticeable slow down in our null_syscall
performance. On a Power9 DD2.2:

  Before        After         Delta     Delta %
  955 cycles    999 cycles    -44	-4.6%

On the plus side this does simplify the code somewhat, because we
don't have to reenable MSR_RI on the restore_math() or
syscall_exit_work() paths which was necessitated previously by the
optimisation.

Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>

1 files changed, 14 insertions, 20 deletions

diff --git a/arch/powerpc/kernel/entry_64.S b/arch/powerpc/kernel/entry_64.S
index a2c168b395d2..c17c1bed6148 100644
--- a/arch/powerpc/kernel/entry_64.S
+++ b/arch/powerpc/kernel/entry_64.S
@@ -236,18 +236,14 @@ system_call_exit:
 	/*
 	 * Disable interrupts so current_thread_info()->flags can't change,
 	 * and so that we don't get interrupted after loading SRR0/1.
+	 *
+	 * Leave MSR_RI enabled for now, because with THREAD_INFO_IN_TASK we
+	 * could fault on the load of the TI_FLAGS below.
 	 */
 #ifdef CONFIG_PPC_BOOK3E
 	wrteei	0
 #else
-	/*
-	 * For performance reasons we clear RI the same time that we
-	 * clear EE. We only need to clear RI just before we restore r13
-	 * below, but batching it with EE saves us one expensive mtmsrd call.
-	 * We have to be careful to restore RI if we branch anywhere from
-	 * here (eg syscall_exit_work).
-	 */
-	li	r11,0
+	li	r11,MSR_RI
 	mtmsrd	r11,1
 #endif /* CONFIG_PPC_BOOK3E */
 
@@ -263,15 +259,7 @@ system_call_exit:
 	bne	3f
 #endif
 2:	addi    r3,r1,STACK_FRAME_OVERHEAD
-#ifdef CONFIG_PPC_BOOK3S
-	li	r10,MSR_RI
-	mtmsrd	r10,1		/* Restore RI */
-#endif
 	bl	restore_math
-#ifdef CONFIG_PPC_BOOK3S
-	li	r11,0
-	mtmsrd	r11,1
-#endif
 	ld	r8,_MSR(r1)
 	ld	r3,RESULT(r1)
 	li	r11,-MAX_ERRNO
@@ -287,6 +275,16 @@ END_FTR_SECTION_IFCLR(CPU_FTR_STCX_CHECKS_ADDRESS)
 	andi.	r6,r8,MSR_PR
 	ld	r4,_LINK(r1)
 
+#ifdef CONFIG_PPC_BOOK3S
+	/*
+	 * Clear MSR_RI, MSR_EE is already and remains disabled. We could do
+	 * this later, but testing shows that doing it here causes less slow
+	 * down than doing it closer to the rfid.
+	 */
+	li	r11,0
+	mtmsrd	r11,1
+#endif
+
 	beq-	1f
 	ACCOUNT_CPU_USER_EXIT(r13, r11, r12)
 
@@ -363,10 +361,6 @@ END_FTR_SECTION_IFSET(CPU_FTR_HAS_PPR)
 	b	.Lsyscall_exit
 	
 .Lsyscall_exit_work:
-#ifdef CONFIG_PPC_BOOK3S
-	li	r10,MSR_RI
-	mtmsrd	r10,1		/* Restore RI */
-#endif
 	/* If TIF_RESTOREALL is set, don't scribble on either r3 or ccr.
 	 If TIF_NOERROR is set, just save r3 as it is. */