1 files changed, 0 insertions, 82 deletions
diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt b/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
deleted file mode 100644
index 178fca08278f..000000000000
--- a/Documentation/devicetree/bindings/interrupt-controller/ti,sci-intr.txt
+++ /dev/null
@@ -1,82 +0,0 @@
-Texas Instruments K3 Interrupt Router
-=====================================
-
-The Interrupt Router (INTR) module provides a mechanism to mux M
-interrupt inputs to N interrupt outputs, where all M inputs are selectable
-to be driven per N output. An Interrupt Router can either handle edge triggered
-or level triggered interrupts and that is fixed in hardware.
-
-                                 Interrupt Router
-                             +----------------------+
-                             |  Inputs     Outputs  |
-        +-------+            | +------+    +-----+  |
-        | GPIO  |----------->| | irq0 |    |  0  |  |       Host IRQ
-        +-------+            | +------+    +-----+  |      controller
-                             |    .           .     |      +-------+
-        +-------+            |    .           .     |----->|  IRQ  |
-        | INTA  |----------->|    .           .     |      +-------+
-        +-------+            |    .        +-----+  |
-                             | +------+    |  N  |  |
-                             | | irqM |    +-----+  |
-                             | +------+             |
-                             |                      |
-                             +----------------------+
-
-There is one register per output (MUXCNTL_N) that controls the selection.
-Configuration of these MUXCNTL_N registers is done by a system controller
-(like the Device Memory and Security Controller on K3 AM654 SoC). System
-controller will keep track of the used and unused registers within the Router.
-Driver should request the system controller to get the range of GIC IRQs
-assigned to the requesting hosts. It is the drivers responsibility to keep
-track of Host IRQs.
-
-Communication between the host processor running an OS and the system
-controller happens through a protocol called TI System Control Interface
-(TISCI protocol). For more details refer:
-Documentation/devicetree/bindings/arm/keystone/ti,sci.txt
-
-TISCI Interrupt Router Node:
-----------------------------
-Required Properties:
-- compatible:		Must be "ti,sci-intr".
-- ti,intr-trigger-type:	Should be one of the following:
-			1: If intr supports edge triggered interrupts.
-			4: If intr supports level triggered interrupts.
-- interrupt-controller:	Identifies the node as an interrupt controller
-- #interrupt-cells:	Specifies the number of cells needed to encode an
-			interrupt source. The value should be 2.
-			First cell should contain the TISCI device ID of source
-			Second cell should contain the interrupt source offset
-			within the device.
-- ti,sci:		Phandle to TI-SCI compatible System controller node.
-- ti,sci-dst-id:	TISCI device ID of the destination IRQ controller.
-- ti,sci-rm-range-girq:	Array of TISCI subtype ids representing the host irqs
-			assigned to this interrupt router. Each subtype id
-			corresponds to a range of host irqs.
-
-For more details on TISCI IRQ resource management refer:
-https://downloads.ti.com/tisci/esd/latest/2_tisci_msgs/rm/rm_irq.html
-
-Example:
---------
-The following example demonstrates both interrupt router node and the consumer
-node(main gpio) on the AM654 SoC:
-
-main_intr: interrupt-controller0 {
-	compatible = "ti,sci-intr";
-	ti,intr-trigger-type = <1>;
-	interrupt-controller;
-	interrupt-parent = <&gic500>;
-	#interrupt-cells = <2>;
-	ti,sci = <&dmsc>;
-	ti,sci-dst-id = <56>;
-	ti,sci-rm-range-girq = <0x1>;
-};
-
-main_gpio0: gpio@600000 {
-	...
-	interrupt-parent = <&main_intr>;
-	interrupts = <57 256>, <57 257>, <57 258>,
-		     <57 259>, <57 260>, <57 261>;
-	...
-};