summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/sound/st,sta350.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/sound/st,sta350.txt')
-rw-r--r--Documentation/devicetree/bindings/sound/st,sta350.txt131
1 files changed, 131 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/sound/st,sta350.txt b/Documentation/devicetree/bindings/sound/st,sta350.txt
new file mode 100644
index 000000000000..b7e71bf5caf4
--- /dev/null
+++ b/Documentation/devicetree/bindings/sound/st,sta350.txt
@@ -0,0 +1,131 @@
+STA350 audio CODEC
+
+The driver for this device only supports I2C.
+
+Required properties:
+
+ - compatible: "st,sta350"
+ - reg: the I2C address of the device for I2C
+ - reset-gpios: a GPIO spec for the reset pin. If specified, it will be
+ deasserted before communication to the codec starts.
+
+ - power-down-gpios: a GPIO spec for the power down pin. If specified,
+ it will be deasserted before communication to the codec
+ starts.
+
+ - vdd-dig-supply: regulator spec, providing 3.3V
+ - vdd-pll-supply: regulator spec, providing 3.3V
+ - vcc-supply: regulator spec, providing 5V - 26V
+
+Optional properties:
+
+ - st,output-conf: number, Selects the output configuration:
+ 0: 2-channel (full-bridge) power, 2-channel data-out
+ 1: 2 (half-bridge). 1 (full-bridge) on-board power
+ 2: 2 Channel (Full-Bridge) Power, 1 Channel FFX
+ 3: 1 Channel Mono-Parallel
+ If parameter is missing, mode 0 will be enabled.
+ This property has to be specified as '/bits/ 8' value.
+
+ - st,ch1-output-mapping: Channel 1 output mapping
+ - st,ch2-output-mapping: Channel 2 output mapping
+ - st,ch3-output-mapping: Channel 3 output mapping
+ 0: Channel 1
+ 1: Channel 2
+ 2: Channel 3
+ If parameter is missing, channel 1 is choosen.
+ This properties have to be specified as '/bits/ 8' values.
+
+ - st,thermal-warning-recover:
+ If present, thermal warning recovery is enabled.
+
+ - st,thermal-warning-adjustment:
+ If present, thermal warning adjustment is enabled.
+
+ - st,fault-detect-recovery:
+ If present, then fault recovery will be enabled.
+
+ - st,ffx-power-output-mode: string
+ The FFX power output mode selects how the FFX output timing is
+ configured. Must be one of these values:
+ - "drop-compensation"
+ - "tapered-compensation"
+ - "full-power-mode"
+ - "variable-drop-compensation" (default)
+
+ - st,drop-compensation-ns: number
+ Only required for "st,ffx-power-output-mode" ==
+ "variable-drop-compensation".
+ Specifies the drop compensation in nanoseconds.
+ The value must be in the range of 0..300, and only
+ multiples of 20 are allowed. Default is 140ns.
+
+ - st,overcurrent-warning-adjustment:
+ If present, overcurrent warning adjustment is enabled.
+
+ - st,max-power-use-mpcc:
+ If present, then MPCC bits are used for MPC coefficients,
+ otherwise standard MPC coefficients are used.
+
+ - st,max-power-corr:
+ If present, power bridge correction for THD reduction near maximum
+ power output is enabled.
+
+ - st,am-reduction-mode:
+ If present, FFX mode runs in AM reduction mode, otherwise normal
+ FFX mode is used.
+
+ - st,odd-pwm-speed-mode:
+ If present, PWM speed mode run on odd speed mode (341.3 kHz) on all
+ channels. If not present, normal PWM spped mode (384 kHz) will be used.
+
+ - st,distortion-compensation:
+ If present, distortion compensation variable uses DCC coefficient.
+ If not present, preset DC coefficient is used.
+
+ - st,invalid-input-detect-mute:
+ If present, automatic invalid input detect mute is enabled.
+
+ - st,activate-mute-output:
+ If present, a mute output will be activated in ase the volume will
+ reach a value lower than -76 dBFS.
+
+ - st,bridge-immediate-off:
+ If present, the bridge will be switched off immediately after the
+ power-down-gpio goes low. Otherwise, the bridge will wait for 13
+ million clock cycles to pass before shutting down.
+
+ - st,noise-shape-dc-cut:
+ If present, the noise-shaping technique on the DC cutoff filter are
+ enabled.
+
+ - st,powerdown-master-volume:
+ If present, the power-down pin and I2C power-down functions will
+ act on the master volume. Otherwise, the functions will act on the
+ mute commands.
+
+ - st,powerdown-delay-divider:
+ If present, the bridge power-down time will be divided by the provided
+ value. If not specified, a divider of 1 will be used. Allowed values
+ are 1, 2, 4, 8, 16, 32, 64 and 128.
+ This property has to be specified as '/bits/ 8' value.
+
+Example:
+
+codec: sta350@38 {
+ compatible = "st,sta350";
+ reg = <0x1c>;
+ reset-gpios = <&gpio1 19 0>;
+ power-down-gpios = <&gpio1 16 0>;
+ st,output-conf = /bits/ 8 <0x3>; // set output to 2-channel
+ // (full-bridge) power,
+ // 2-channel data-out
+ st,ch1-output-mapping = /bits/ 8 <0>; // set channel 1 output ch 1
+ st,ch2-output-mapping = /bits/ 8 <0>; // set channel 2 output ch 1
+ st,ch3-output-mapping = /bits/ 8 <0>; // set channel 3 output ch 1
+ st,max-power-correction; // enables power bridge
+ // correction for THD reduction
+ // near maximum power output
+ st,invalid-input-detect-mute; // mute if no valid digital
+ // audio signal is provided.
+};