diff options
Diffstat (limited to 'Documentation/devicetree')
22 files changed, 882 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/c6x/clocks.txt b/Documentation/devicetree/bindings/c6x/clocks.txt new file mode 100644 index 000000000000..a04f5fd30122 --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/clocks.txt @@ -0,0 +1,40 @@ +C6X PLL Clock Controllers +------------------------- + +This is a first-cut support for the SoC clock controllers. This is still +under development and will probably change as the common device tree +clock support is added to the kernel. + +Required properties: + +- compatible: "ti,c64x+pll" + May also have SoC-specific value to support SoC-specific initialization + in the driver. One of: + "ti,c6455-pll" + "ti,c6457-pll" + "ti,c6472-pll" + "ti,c6474-pll" + +- reg: base address and size of register area +- clock-frequency: input clock frequency in hz + + +Optional properties: + +- ti,c64x+pll-bypass-delay: CPU cycles to delay when entering bypass mode + +- ti,c64x+pll-reset-delay: CPU cycles to delay after PLL reset + +- ti,c64x+pll-lock-delay: CPU cycles to delay after PLL frequency change + +Example: + + clock-controller@29a0000 { + compatible = "ti,c6472-pll", "ti,c64x+pll"; + reg = <0x029a0000 0x200>; + clock-frequency = <25000000>; + + ti,c64x+pll-bypass-delay = <200>; + ti,c64x+pll-reset-delay = <12000>; + ti,c64x+pll-lock-delay = <80000>; + }; diff --git a/Documentation/devicetree/bindings/c6x/dscr.txt b/Documentation/devicetree/bindings/c6x/dscr.txt new file mode 100644 index 000000000000..d847758f2b20 --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/dscr.txt @@ -0,0 +1,127 @@ +Device State Configuration Registers +------------------------------------ + +TI C6X SoCs contain a region of miscellaneous registers which provide various +function for SoC control or status. Details vary considerably among from SoC +to SoC with no two being alike. + +In general, the Device State Configuraion Registers (DSCR) will provide one or +more configuration registers often protected by a lock register where one or +more key values must be written to a lock register in order to unlock the +configuration register for writes. These configuration register may be used to +enable (and disable in some cases) SoC pin drivers, select peripheral clock +sources (internal or pin), etc. In some cases, a configuration register is +write once or the individual bits are write once. In addition to device config, +the DSCR block may provide registers which which are used to reset peripherals, +provide device ID information, provide ethernet MAC addresses, as well as other +miscellaneous functions. + +For device state control (enable/disable), each device control is assigned an +id which is used by individual device drivers to control the state as needed. + +Required properties: + +- compatible: must be "ti,c64x+dscr" +- reg: register area base and size + +Optional properties: + + NOTE: These are optional in that not all SoCs will have all properties. For + SoCs which do support a given property, leaving the property out of the + device tree will result in reduced functionality or possibly driver + failure. + +- ti,dscr-devstat + offset of the devstat register + +- ti,dscr-silicon-rev + offset, start bit, and bitsize of silicon revision field + +- ti,dscr-rmii-resets + offset and bitmask of RMII reset field. May have multiple tuples if more + than one ethernet port is available. + +- ti,dscr-locked-regs + possibly multiple tuples describing registers which are write protected by + a lock register. Each tuple consists of the register offset, lock register + offsset, and the key value used to unlock the register. + +- ti,dscr-kick-regs + offset and key values of two "kick" registers used to write protect other + registers in DSCR. On SoCs using kick registers, the first key must be + written to the first kick register and the second key must be written to + the second register before other registers in the area are write-enabled. + +- ti,dscr-mac-fuse-regs + MAC addresses are contained in two registers. Each element of a MAC address + is contained in a single byte. This property has two tuples. Each tuple has + a register offset and four cells representing bytes in the register from + most significant to least. The value of these four cells is the MAC byte + index (1-6) of the byte within the register. A value of 0 means the byte + is unused in the MAC address. + +- ti,dscr-devstate-ctl-regs + This property describes the bitfields used to control the state of devices. + Each tuple describes a range of identical bitfields used to control one or + more devices (one bitfield per device). The layout of each tuple is: + + start_id num_ids reg enable disable start_bit nbits + + Where: + start_id is device id for the first device control in the range + num_ids is the number of device controls in the range + reg is the offset of the register holding the control bits + enable is the value to enable a device + disable is the value to disable a device (0xffffffff if cannot disable) + start_bit is the bit number of the first bit in the range + nbits is the number of bits per device control + +- ti,dscr-devstate-stat-regs + This property describes the bitfields used to provide device state status + for device states controlled by the DSCR. Each tuple describes a range of + identical bitfields used to provide status for one or more devices (one + bitfield per device). The layout of each tuple is: + + start_id num_ids reg enable disable start_bit nbits + + Where: + start_id is device id for the first device status in the range + num_ids is the number of devices covered by the range + reg is the offset of the register holding the status bits + enable is the value indicating device is enabled + disable is the value indicating device is disabled + start_bit is the bit number of the first bit in the range + nbits is the number of bits per device status + +- ti,dscr-privperm + Offset and default value for register used to set access privilege for + some SoC devices. + + +Example: + + device-state-config-regs@2a80000 { + compatible = "ti,c64x+dscr"; + reg = <0x02a80000 0x41000>; + + ti,dscr-devstat = <0>; + ti,dscr-silicon-rev = <8 28 0xf>; + ti,dscr-rmii-resets = <0x40020 0x00040000>; + + ti,dscr-locked-regs = <0x40008 0x40004 0x0f0a0b00>; + ti,dscr-devstate-ctl-regs = + <0 12 0x40008 1 0 0 2 + 12 1 0x40008 3 0 30 2 + 13 2 0x4002c 1 0xffffffff 0 1>; + ti,dscr-devstate-stat-regs = + <0 10 0x40014 1 0 0 3 + 10 2 0x40018 1 0 0 3>; + + ti,dscr-mac-fuse-regs = <0x700 1 2 3 4 + 0x704 5 6 0 0>; + + ti,dscr-privperm = <0x41c 0xaaaaaaaa>; + + ti,dscr-kick-regs = <0x38 0x83E70B13 + 0x3c 0x95A4F1E0>; + }; diff --git a/Documentation/devicetree/bindings/c6x/emifa.txt b/Documentation/devicetree/bindings/c6x/emifa.txt new file mode 100644 index 000000000000..0ff6e9b9a13f --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/emifa.txt @@ -0,0 +1,62 @@ +External Memory Interface +------------------------- + +The emifa node describes a simple external bus controller found on some C6X +SoCs. This interface provides external busses with a number of chip selects. + +Required properties: + +- compatible: must be "ti,c64x+emifa", "simple-bus" +- reg: register area base and size +- #address-cells: must be 2 (chip-select + offset) +- #size-cells: must be 1 +- ranges: mapping from EMIFA space to parent space + + +Optional properties: + +- ti,dscr-dev-enable: Device ID if EMIF is enabled/disabled from DSCR + +- ti,emifa-burst-priority: + Number of memory transfers after which the EMIF will elevate the priority + of the oldest command in the command FIFO. Setting this field to 255 + disables this feature, thereby allowing old commands to stay in the FIFO + indefinitely. + +- ti,emifa-ce-config: + Configuration values for each of the supported chip selects. + +Example: + + emifa@70000000 { + compatible = "ti,c64x+emifa", "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + reg = <0x70000000 0x100>; + ranges = <0x2 0x0 0xa0000000 0x00000008 + 0x3 0x0 0xb0000000 0x00400000 + 0x4 0x0 0xc0000000 0x10000000 + 0x5 0x0 0xD0000000 0x10000000>; + + ti,dscr-dev-enable = <13>; + ti,emifa-burst-priority = <255>; + ti,emifa-ce-config = <0x00240120 + 0x00240120 + 0x00240122 + 0x00240122>; + + flash@3,0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "cfi-flash"; + reg = <0x3 0x0 0x400000>; + bank-width = <1>; + device-width = <1>; + partition@0 { + reg = <0x0 0x400000>; + label = "NOR"; + }; + }; + }; + +This shows a flash chip attached to chip select 3. diff --git a/Documentation/devicetree/bindings/c6x/interrupt.txt b/Documentation/devicetree/bindings/c6x/interrupt.txt new file mode 100644 index 000000000000..42bb796cc4ad --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/interrupt.txt @@ -0,0 +1,104 @@ +C6X Interrupt Chips +------------------- + +* C64X+ Core Interrupt Controller + + The core interrupt controller provides 16 prioritized interrupts to the + C64X+ core. Priority 0 and 1 are used for reset and NMI respectively. + Priority 2 and 3 are reserved. Priority 4-15 are used for interrupt + sources coming from outside the core. + + Required properties: + -------------------- + - compatible: Should be "ti,c64x+core-pic"; + - #interrupt-cells: <1> + + Interrupt Specifier Definition + ------------------------------ + Single cell specifying the core interrupt priority level (4-15) where + 4 is highest priority and 15 is lowest priority. + + Example + ------- + core_pic: interrupt-controller@0 { + interrupt-controller; + #interrupt-cells = <1>; + compatible = "ti,c64x+core-pic"; + }; + + + +* C64x+ Megamodule Interrupt Controller + + The megamodule PIC consists of four interrupt mupliplexers each of which + combine up to 32 interrupt inputs into a single interrupt output which + may be cascaded into the core interrupt controller. The megamodule PIC + has a total of 12 outputs cascading into the core interrupt controller. + One for each core interrupt priority level. In addition to the combined + interrupt sources, individual megamodule interrupts may be cascaded to + the core interrupt controller. When an individual interrupt is cascaded, + it is no longer handled through a megamodule interrupt combiner and is + considered to have the core interrupt controller as the parent. + + Required properties: + -------------------- + - compatible: "ti,c64x+megamod-pic" + - interrupt-controller + - #interrupt-cells: <1> + - reg: base address and size of register area + - interrupt-parent: must be core interrupt controller + - interrupts: This should have four cells; one for each interrupt combiner. + The cells contain the core priority interrupt to which the + corresponding combiner output is wired. + + Optional properties: + -------------------- + - ti,c64x+megamod-pic-mux: Array of 12 cells correspnding to the 12 core + priority interrupts. The first cell corresponds to + core priority 4 and the last cell corresponds to + core priority 15. The value of each cell is the + megamodule interrupt source which is MUXed to + the core interrupt corresponding to the cell + position. Allowed values are 4 - 127. Mapping for + interrupts 0 - 3 (combined interrupt sources) are + ignored. + + Interrupt Specifier Definition + ------------------------------ + Single cell specifying the megamodule interrupt source (4-127). Note that + interrupts mapped directly to the core with "ti,c64x+megamod-pic-mux" will + use the core interrupt controller as their parent and the specifier will + be the core priority level, not the megamodule interrupt number. + + Examples + -------- + megamod_pic: interrupt-controller@1800000 { + compatible = "ti,c64x+megamod-pic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x1800000 0x1000>; + interrupt-parent = <&core_pic>; + interrupts = < 12 13 14 15 >; + }; + + This is a minimal example where all individual interrupts go through a + combiner. Combiner-0 is mapped to core interrupt 12, combiner-1 is mapped + to interrupt 13, etc. + + + megamod_pic: interrupt-controller@1800000 { + compatible = "ti,c64x+megamod-pic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x1800000 0x1000>; + interrupt-parent = <&core_pic>; + interrupts = < 12 13 14 15 >; + ti,c64x+megamod-pic-mux = < 0 0 0 0 + 32 0 0 0 + 0 0 0 0 >; + }; + + This the same as the first example except that megamodule interrupt 32 is + mapped directly to core priority interrupt 8. The node using this interrupt + must set the core controller as its interrupt parent and use 8 in the + interrupt specifier value. diff --git a/Documentation/devicetree/bindings/c6x/soc.txt b/Documentation/devicetree/bindings/c6x/soc.txt new file mode 100644 index 000000000000..b1e4973b5769 --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/soc.txt @@ -0,0 +1,28 @@ +C6X System-on-Chip +------------------ + +Required properties: + +- compatible: "simple-bus" +- #address-cells: must be 1 +- #size-cells: must be 1 +- ranges + +Optional properties: + +- model: specific SoC model + +- nodes for IP blocks within SoC + + +Example: + + soc { + compatible = "simple-bus"; + model = "tms320c6455"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + ... + }; diff --git a/Documentation/devicetree/bindings/c6x/timer64.txt b/Documentation/devicetree/bindings/c6x/timer64.txt new file mode 100644 index 000000000000..95911fe70224 --- /dev/null +++ b/Documentation/devicetree/bindings/c6x/timer64.txt @@ -0,0 +1,26 @@ +Timer64 +------- + +The timer64 node describes C6X event timers. + +Required properties: + +- compatible: must be "ti,c64x+timer64" +- reg: base address and size of register region +- interrupt-parent: interrupt controller +- interrupts: interrupt id + +Optional properties: + +- ti,dscr-dev-enable: Device ID used to enable timer IP through DSCR interface. + +- ti,core-mask: on multi-core SoCs, bitmask of cores allowed to use this timer. + +Example: + timer0: timer@25e0000 { + compatible = "ti,c64x+timer64"; + ti,core-mask = < 0x01 >; + reg = <0x25e0000 0x40>; + interrupt-parent = <&megamod_pic>; + interrupts = < 16 >; + }; diff --git a/Documentation/devicetree/bindings/dma/atmel-dma.txt b/Documentation/devicetree/bindings/dma/atmel-dma.txt new file mode 100644 index 000000000000..3c046ee6e8b5 --- /dev/null +++ b/Documentation/devicetree/bindings/dma/atmel-dma.txt @@ -0,0 +1,14 @@ +* Atmel Direct Memory Access Controller (DMA) + +Required properties: +- compatible: Should be "atmel,<chip>-dma" +- reg: Should contain DMA registers location and length +- interrupts: Should contain DMA interrupt + +Examples: + +dma@ffffec00 { + compatible = "atmel,at91sam9g45-dma"; + reg = <0xffffec00 0x200>; + interrupts = <21>; +}; diff --git a/Documentation/devicetree/bindings/i2c/omap-i2c.txt b/Documentation/devicetree/bindings/i2c/omap-i2c.txt new file mode 100644 index 000000000000..56564aa4b444 --- /dev/null +++ b/Documentation/devicetree/bindings/i2c/omap-i2c.txt @@ -0,0 +1,30 @@ +I2C for OMAP platforms + +Required properties : +- compatible : Must be "ti,omap3-i2c" or "ti,omap4-i2c" +- ti,hwmods : Must be "i2c<n>", n being the instance number (1-based) +- #address-cells = <1>; +- #size-cells = <0>; + +Recommended properties : +- clock-frequency : Desired I2C bus clock frequency in Hz. Otherwise + the default 100 kHz frequency will be used. + +Optional properties: +- Child nodes conforming to i2c bus binding + +Note: Current implementation will fetch base address, irq and dma +from omap hwmod data base during device registration. +Future plan is to migrate hwmod data base contents into device tree +blob so that, all the required data will be used from device tree dts +file. + +Examples : + +i2c1: i2c@0 { + compatible = "ti,omap3-i2c"; + #address-cells = <1>; + #size-cells = <0>; + ti,hwmods = "i2c1"; + clock-frequency = <400000>; +}; diff --git a/Documentation/devicetree/bindings/input/tegra-kbc.txt b/Documentation/devicetree/bindings/input/tegra-kbc.txt new file mode 100644 index 000000000000..5ecfa99089b4 --- /dev/null +++ b/Documentation/devicetree/bindings/input/tegra-kbc.txt @@ -0,0 +1,18 @@ +* Tegra keyboard controller + +Required properties: +- compatible: "nvidia,tegra20-kbc" + +Optional properties: +- debounce-delay: delay in milliseconds per row scan for debouncing +- repeat-delay: delay in milliseconds before repeat starts +- ghost-filter: enable ghost filtering for this device +- wakeup-source: configure keyboard as a wakeup source for suspend/resume + +Example: + +keyboard: keyboard { + compatible = "nvidia,tegra20-kbc"; + reg = <0x7000e200 0x100>; + ghost-filter; +}; diff --git a/Documentation/devicetree/bindings/mfd/mc13xxx.txt b/Documentation/devicetree/bindings/mfd/mc13xxx.txt new file mode 100644 index 000000000000..19f6af47a792 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/mc13xxx.txt @@ -0,0 +1,78 @@ +* Freescale MC13783/MC13892 Power Management Integrated Circuit (PMIC) + +Required properties: +- compatible : Should be "fsl,mc13783" or "fsl,mc13892" + +Optional properties: +- fsl,mc13xxx-uses-adc : Indicate the ADC is being used +- fsl,mc13xxx-uses-codec : Indicate the Audio Codec is being used +- fsl,mc13xxx-uses-rtc : Indicate the RTC is being used +- fsl,mc13xxx-uses-touch : Indicate the touchscreen controller is being used + +Sub-nodes: +- regulators : Contain the regulator nodes. The MC13892 regulators are + bound using their names as listed below with their registers and bits + for enabling. + + vcoincell : regulator VCOINCELL (register 13, bit 23) + sw1 : regulator SW1 (register 24, bit 0) + sw2 : regulator SW2 (register 25, bit 0) + sw3 : regulator SW3 (register 26, bit 0) + sw4 : regulator SW4 (register 27, bit 0) + swbst : regulator SWBST (register 29, bit 20) + vgen1 : regulator VGEN1 (register 32, bit 0) + viohi : regulator VIOHI (register 32, bit 3) + vdig : regulator VDIG (register 32, bit 9) + vgen2 : regulator VGEN2 (register 32, bit 12) + vpll : regulator VPLL (register 32, bit 15) + vusb2 : regulator VUSB2 (register 32, bit 18) + vgen3 : regulator VGEN3 (register 33, bit 0) + vcam : regulator VCAM (register 33, bit 6) + vvideo : regulator VVIDEO (register 33, bit 12) + vaudio : regulator VAUDIO (register 33, bit 15) + vsd : regulator VSD (register 33, bit 18) + gpo1 : regulator GPO1 (register 34, bit 6) + gpo2 : regulator GPO2 (register 34, bit 8) + gpo3 : regulator GPO3 (register 34, bit 10) + gpo4 : regulator GPO4 (register 34, bit 12) + pwgt1spi : regulator PWGT1SPI (register 34, bit 15) + pwgt2spi : regulator PWGT2SPI (register 34, bit 16) + vusb : regulator VUSB (register 50, bit 3) + + The bindings details of individual regulator device can be found in: + Documentation/devicetree/bindings/regulator/regulator.txt + +Examples: + +ecspi@70010000 { /* ECSPI1 */ + fsl,spi-num-chipselects = <2>; + cs-gpios = <&gpio3 24 0>, /* GPIO4_24 */ + <&gpio3 25 0>; /* GPIO4_25 */ + status = "okay"; + + pmic: mc13892@0 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mc13892"; + spi-max-frequency = <6000000>; + reg = <0>; + interrupt-parent = <&gpio0>; + interrupts = <8>; + + regulators { + sw1_reg: mc13892__sw1 { + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <1375000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: mc13892__sw2 { + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1850000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/mfd/twl-familly.txt b/Documentation/devicetree/bindings/mfd/twl-familly.txt new file mode 100644 index 000000000000..a66fcf946759 --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/twl-familly.txt @@ -0,0 +1,47 @@ +Texas Instruments TWL family + +The TWLs are Integrated Power Management Chips. +Some version might contain much more analog function like +USB transceiver or Audio amplifier. +These chips are connected to an i2c bus. + + +Required properties: +- compatible : Must be "ti,twl4030"; + For Integrated power-management/audio CODEC device used in OMAP3 + based boards +- compatible : Must be "ti,twl6030"; + For Integrated power-management used in OMAP4 based boards +- interrupts : This i2c device has an IRQ line connected to the main SoC +- interrupt-controller : Since the twl support several interrupts internally, + it is considered as an interrupt controller cascaded to the SoC one. +- #interrupt-cells = <1>; +- interrupt-parent : The parent interrupt controller. + +Optional node: +- Child nodes contain in the twl. The twl family is made of several variants + that support a different number of features. + The children nodes will thus depend of the capability of the variant. + + +Example: +/* + * Integrated Power Management Chip + * http://www.ti.com/lit/ds/symlink/twl6030.pdf + */ +twl@48 { + compatible = "ti,twl6030"; + reg = <0x48>; + interrupts = <39>; /* IRQ_SYS_1N cascaded to gic */ + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + #address-cells = <1>; + #size-cells = <0>; + + twl_rtc { + compatible = "ti,twl_rtc"; + interrupts = <11>; + reg = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt new file mode 100644 index 000000000000..719f4dc58df7 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpio-control-nand.txt @@ -0,0 +1,44 @@ +GPIO assisted NAND flash + +The GPIO assisted NAND flash uses a memory mapped interface to +read/write the NAND commands and data and GPIO pins for the control +signals. + +Required properties: +- compatible : "gpio-control-nand" +- reg : should specify localbus chip select and size used for the chip. The + resource describes the data bus connected to the NAND flash and all accesses + are made in native endianness. +- #address-cells, #size-cells : Must be present if the device has sub-nodes + representing partitions. +- gpios : specifies the gpio pins to control the NAND device. nwp is an + optional gpio and may be set to 0 if not present. + +Optional properties: +- bank-width : Width (in bytes) of the device. If not present, the width + defaults to 1 byte. +- chip-delay : chip dependent delay for transferring data from array to + read registers (tR). If not present then a default of 20us is used. +- gpio-control-nand,io-sync-reg : A 64-bit physical address for a read + location used to guard against bus reordering with regards to accesses to + the GPIO's and the NAND flash data bus. If present, then after changing + GPIO state and before and after command byte writes, this register will be + read to ensure that the GPIO accesses have completed. + +Examples: + +gpio-nand@1,0 { + compatible = "gpio-control-nand"; + reg = <1 0x0000 0x2>; + #address-cells = <1>; + #size-cells = <1>; + gpios = <&banka 1 0 /* rdy */ + &banka 2 0 /* nce */ + &banka 3 0 /* ale */ + &banka 4 0 /* cle */ + 0 /* nwp */>; + + partition@0 { + ... + }; +}; diff --git a/Documentation/devicetree/bindings/power_supply/olpc_battery.txt b/Documentation/devicetree/bindings/power_supply/olpc_battery.txt new file mode 100644 index 000000000000..c8901b3992d9 --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/olpc_battery.txt @@ -0,0 +1,5 @@ +OLPC battery +~~~~~~~~~~~~ + +Required properties: + - compatible : "olpc,xo1-battery" diff --git a/Documentation/devicetree/bindings/power_supply/sbs_sbs-battery.txt b/Documentation/devicetree/bindings/power_supply/sbs_sbs-battery.txt new file mode 100644 index 000000000000..c40e8926facf --- /dev/null +++ b/Documentation/devicetree/bindings/power_supply/sbs_sbs-battery.txt @@ -0,0 +1,23 @@ +SBS sbs-battery +~~~~~~~~~~ + +Required properties : + - compatible : "sbs,sbs-battery" + +Optional properties : + - sbs,i2c-retry-count : The number of times to retry i2c transactions on i2c + IO failure. + - sbs,poll-retry-count : The number of times to try looking for new status + after an external change notification. + - sbs,battery-detect-gpios : The gpio which signals battery detection and + a flag specifying its polarity. + +Example: + + bq20z75@b { + compatible = "sbs,sbs-battery"; + reg = < 0xb >; + sbs,i2c-retry-count = <2>; + sbs,poll-retry-count = <10>; + sbs,battery-detect-gpios = <&gpio-controller 122 1>; + } diff --git a/Documentation/devicetree/bindings/resource-names.txt b/Documentation/devicetree/bindings/resource-names.txt new file mode 100644 index 000000000000..e280fef6f265 --- /dev/null +++ b/Documentation/devicetree/bindings/resource-names.txt @@ -0,0 +1,54 @@ +Some properties contain an ordered list of 1 or more datum which are +normally accessed by index. However, some devices will have multiple +values which are more naturally accessed by name. Device nodes can +include a supplemental property for assigning names to each of the list +items. The names property consists of a list of strings in the same +order as the data in the resource property. + +The following supplemental names properties are defined. + +Resource Property Supplemental Names Property +----------------- --------------------------- +reg reg-names +clocks clock-names +interrupts interrupt-names + +Usage: + +The -names property must be used in conjunction with the normal resource +property. If not it will be ignored. + +Examples: + +l4-abe { + compatible = "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + ranges = <0 0 0x48000000 0x00001000>, /* MPU path */ + <1 0 0x49000000 0x00001000>; /* L3 path */ + mcasp { + compatible = "ti,mcasp"; + reg = <0 0x10 0x10>, <0 0x20 0x10>, + <1 0x10 0x10>, <1 0x20 0x10>; + reg-names = "mpu", "dat", + "dma", "dma_dat"; + interrupts = <11>, <12>; + interrupt-names = "rx", "tx"; + }; + + timer { + compatible = "ti,timer"; + reg = <0 0x40 0x10>, <1 0x40 0x10>; + reg-names = "mpu", "dma"; + }; +}; + + +usb { + compatible = "ti,usb-host"; + reg = <0x4a064000 0x800>, <0x4a064800 0x200>, + <0x4a064c00 0x200>; + reg-names = "config", "ohci", "ehci"; + interrupts = <14>, <15>; + interrupt-names = "ohci", "ehci"; +}; diff --git a/Documentation/devicetree/bindings/rtc/twl-rtc.txt b/Documentation/devicetree/bindings/rtc/twl-rtc.txt new file mode 100644 index 000000000000..596e0c97be7a --- /dev/null +++ b/Documentation/devicetree/bindings/rtc/twl-rtc.txt @@ -0,0 +1,12 @@ +* TI twl RTC + +The TWL family (twl4030/6030) contains a RTC. + +Required properties: +- compatible : Should be twl4030-rtc + +Examples: + +rtc@0 { + compatible = "ti,twl4030-rtc"; +}; diff --git a/Documentation/devicetree/bindings/sound/tegra-audio-wm8903.txt b/Documentation/devicetree/bindings/sound/tegra-audio-wm8903.txt new file mode 100644 index 000000000000..d5b0da8bf1d8 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tegra-audio-wm8903.txt @@ -0,0 +1,71 @@ +NVIDIA Tegra audio complex + +Required properties: +- compatible : "nvidia,tegra-audio-wm8903" +- nvidia,model : The user-visible name of this sound complex. +- nvidia,audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources and + sinks are the WM8903's pins, and the jacks on the board: + + WM8903 pins: + + * IN1L + * IN1R + * IN2L + * IN2R + * IN3L + * IN3R + * DMICDAT + * HPOUTL + * HPOUTR + * LINEOUTL + * LINEOUTR + * LOP + * LON + * ROP + * RON + * MICBIAS + + Board connectors: + + * Headphone Jack + * Int Spk + * Mic Jack + +- nvidia,i2s-controller : The phandle of the Tegra I2S1 controller +- nvidia,audio-codec : The phandle of the WM8903 audio codec + +Optional properties: +- nvidia,spkr-en-gpios : The GPIO that enables the speakers +- nvidia,hp-mute-gpios : The GPIO that mutes the headphones +- nvidia,hp-det-gpios : The GPIO that detect headphones are plugged in +- nvidia,int-mic-en-gpios : The GPIO that enables the internal microphone +- nvidia,ext-mic-en-gpios : The GPIO that enables the external microphone + +Example: + +sound { + compatible = "nvidia,tegra-audio-wm8903-harmony", + "nvidia,tegra-audio-wm8903" + nvidia,model = "tegra-wm8903-harmony"; + + nvidia,audio-routing = + "Headphone Jack", "HPOUTR", + "Headphone Jack", "HPOUTL", + "Int Spk", "ROP", + "Int Spk", "RON", + "Int Spk", "LOP", + "Int Spk", "LON", + "Mic Jack", "MICBIAS", + "IN1L", "Mic Jack"; + + nvidia,i2s-controller = <&i2s1>; + nvidia,audio-codec = <&wm8903>; + + nvidia,spkr-en-gpios = <&codec 2 0>; + nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */ + nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */ + nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */ +}; + diff --git a/Documentation/devicetree/bindings/sound/tegra20-das.txt b/Documentation/devicetree/bindings/sound/tegra20-das.txt new file mode 100644 index 000000000000..6de3a7ee4efb --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tegra20-das.txt @@ -0,0 +1,12 @@ +NVIDIA Tegra 20 DAS (Digital Audio Switch) controller + +Required properties: +- compatible : "nvidia,tegra20-das" +- reg : Should contain DAS registers location and length + +Example: + +das@70000c00 { + compatible = "nvidia,tegra20-das"; + reg = <0x70000c00 0x80>; +}; diff --git a/Documentation/devicetree/bindings/sound/tegra20-i2s.txt b/Documentation/devicetree/bindings/sound/tegra20-i2s.txt new file mode 100644 index 000000000000..0df2b5c816e3 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/tegra20-i2s.txt @@ -0,0 +1,17 @@ +NVIDIA Tegra 20 I2S controller + +Required properties: +- compatible : "nvidia,tegra20-i2s" +- reg : Should contain I2S registers location and length +- interrupts : Should contain I2S interrupt +- nvidia,dma-request-selector : The Tegra DMA controller's phandle and + request selector for this I2S controller + +Example: + +i2s@70002800 { + compatible = "nvidia,tegra20-i2s"; + reg = <0x70002800 0x200>; + interrupts = < 45 >; + nvidia,dma-request-selector = < &apbdma 2 >; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8903.txt b/Documentation/devicetree/bindings/sound/wm8903.txt new file mode 100644 index 000000000000..f102cbc42694 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8903.txt @@ -0,0 +1,50 @@ +WM8903 audio CODEC + +This device supports I2C only. + +Required properties: + + - compatible : "wlf,wm8903" + + - reg : the I2C address of the device. + + - gpio-controller : Indicates this device is a GPIO controller. + + - #gpio-cells : Should be two. The first cell is the pin number and the + second cell is used to specify optional parameters (currently unused). + +Optional properties: + + - interrupts : The interrupt line the codec is connected to. + + - micdet-cfg : Default register value for R6 (Mic Bias). If absent, the + default is 0. + + - micdet-delay : The debounce delay for microphone detection in mS. If + absent, the default is 100. + + - gpio-cfg : A list of GPIO configuration register values. The list must + be 5 entries long. If absent, no configuration of these registers is + performed. If any entry has the value 0xffffffff, that GPIO's + configuration will not be modified. + +Example: + +codec: wm8903@1a { + compatible = "wlf,wm8903"; + reg = <0x1a>; + interrupts = < 347 >; + + gpio-controller; + #gpio-cells = <2>; + + micdet-cfg = <0>; + micdet-delay = <100>; + gpio-cfg = < + 0x0600 /* DMIC_LR, output */ + 0x0680 /* DMIC_DAT, input */ + 0x0000 /* GPIO, output, low */ + 0x0200 /* Interrupt, output */ + 0x01a0 /* BCLK, input, active high */ + >; +}; diff --git a/Documentation/devicetree/bindings/sound/wm8994.txt b/Documentation/devicetree/bindings/sound/wm8994.txt new file mode 100644 index 000000000000..7a7eb1e7bda6 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/wm8994.txt @@ -0,0 +1,18 @@ +WM1811/WM8994/WM8958 audio CODEC + +These devices support both I2C and SPI (configured with pin strapping +on the board). + +Required properties: + + - compatible : "wlf,wm1811", "wlf,wm8994", "wlf,wm8958" + + - reg : the I2C address of the device for I2C, the chip select + number for SPI. + +Example: + +codec: wm8994@1a { + compatible = "wlf,wm8994"; + reg = <0x1a>; +}; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 18626965159e..ecc6a6cd26c1 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -34,6 +34,7 @@ powervr Imagination Technologies qcom Qualcomm, Inc. ramtron Ramtron International samsung Samsung Semiconductor +sbs Smart Battery System schindler Schindler sil Silicon Image simtek @@ -41,4 +42,5 @@ sirf SiRF Technology, Inc. st STMicroelectronics stericsson ST-Ericsson ti Texas Instruments +wlf Wolfson Microelectronics xlnx Xilinx |