diff options
Diffstat (limited to 'Documentation')
58 files changed, 2488 insertions, 195 deletions
diff --git a/Documentation/ABI/stable/sysfs-bus-nvmem b/Documentation/ABI/stable/sysfs-bus-nvmem index aa89adf18bc5..0ae8cb074acf 100644 --- a/Documentation/ABI/stable/sysfs-bus-nvmem +++ b/Documentation/ABI/stable/sysfs-bus-nvmem @@ -11,7 +11,7 @@ Description: Read returns '0' or '1' for read-write or read-only modes respectively. Write parses one of 'YyTt1NnFf0', or [oO][NnFf] for "on" - and "off", i.e. what kstrbool() supports. + and "off", i.e. what kstrtobool() supports. Note: This file is only present if CONFIG_NVMEM_SYSFS is enabled. diff --git a/Documentation/ABI/testing/debugfs-iio-ad9467 b/Documentation/ABI/testing/debugfs-iio-ad9467 new file mode 100644 index 000000000000..0352fca1f7f2 --- /dev/null +++ b/Documentation/ABI/testing/debugfs-iio-ad9467 @@ -0,0 +1,39 @@ +What: /sys/kernel/debug/iio/iio:deviceX/calibration_table_dump +KernelVersion: 6.11 +Contact: linux-iio@vger.kernel.org +Description: + This dumps the calibration table that was filled during the + digital interface tuning process. + +What: /sys/kernel/debug/iio/iio:deviceX/in_voltage_test_mode_available +KernelVersion: 6.11 +Contact: linux-iio@vger.kernel.org +Description: + List all the available test tones: + - off + - midscale_short + - pos_fullscale + - neg_fullscale + - checkerboard + - prbs23 + - prbs9 + - one_zero_toggle + - user + - bit_toggle + - sync + - one_bit_high + - mixed_bit_frequency + - ramp + + Note that depending on the actual device being used, some of the + above might not be available (and they won't be listed when + reading the file). + +What: /sys/kernel/debug/iio/iio:deviceX/in_voltageY_test_mode +KernelVersion: 6.11 +Contact: linux-iio@vger.kernel.org +Description: + Writing to this file will initiate one of available test tone on + channel Y. Reading it, shows which test is running. In cases + where an IIO backend is available and supports the test tone, + additional information about the data correctness is given. diff --git a/Documentation/ABI/testing/debugfs-iio-backend b/Documentation/ABI/testing/debugfs-iio-backend new file mode 100644 index 000000000000..01ab94469432 --- /dev/null +++ b/Documentation/ABI/testing/debugfs-iio-backend @@ -0,0 +1,20 @@ +What: /sys/kernel/debug/iio/iio:deviceX/backendY/name +KernelVersion: 6.11 +Contact: linux-iio@vger.kernel.org +Description: + Name of Backend Y connected to device X. + +What: /sys/kernel/debug/iio/iio:deviceX/backendY/direct_reg_access +KernelVersion: 6.11 +Contact: linux-iio@vger.kernel.org +Description: + Directly access the registers of backend Y. Typical usage is: + + Reading address 0x50 + echo 0x50 > direct_reg_access + cat direct_reg_access + + Writing address 0x50 + echo 0x50 0x3 > direct_reg_access + //readback address 0x50 + cat direct_reg_access diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index 7cee78ad4108..89943c2d54e8 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -523,13 +523,27 @@ Description: What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_altvoltageY_i_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_altvoltageY_q_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_capacitance_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_illuminance_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_illuminance0_calibbias -What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibbias -What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_intensityY_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_magn_z_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_pressure_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_proximity_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_resistance_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_temp_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibbias +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_calibbias +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_calibbias KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: @@ -541,6 +555,10 @@ Description: What: /sys/bus/iio/devices/iio:deviceX/in_accel_calibbias_available What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_calibbias_available +What: /sys/bus/iio/devices/iio:deviceX/in_temp_calibbias_available +What: /sys/bus/iio/devices/iio:deviceX/in_proximity_calibbias_available +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibbias_available +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_calibbias_available KernelVersion: 5.8 Contact: linux-iio@vger.kernel.org Description: @@ -549,25 +567,34 @@ Description: - a small discrete set of values like "0 2 4 6 8" - a range specified as "[min step max]" -What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_i_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_q_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltage_i_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltage_q_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_altvoltage_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltage_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_altvoltage_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_capacitance_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_illuminance_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_illuminance0_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_intensity_both_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_intensity_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_intensity_ir_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_magn_z_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_pressure_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_illuminance_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltage_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltage_i_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltage_q_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_i_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_q_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_calibscale +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_calibscale +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_calibscale KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: @@ -575,6 +602,20 @@ Description: production inaccuracies). If shared across all channels, <type>_calibscale is used. +What: /sys/bus/iio/devices/iio:deviceX/in_illuminanceY_calibscale_available +What: /sys/bus/iio/devices/iio:deviceX/in_intensityY_calibscale_available +What: /sys/bus/iio/devices/iio:deviceX/in_proximityY_calibscale_available +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale_available +KernelVersion: 4.8 +Contact: linux-iio@vger.kernel.org +Description: + Available values of calibscale. Maybe expressed as either of: + + - a small discrete set of values like "1 8 16" + - a range specified as "[min step max]" + + If shared across all channels, <type>_calibscale_available is used. + What: /sys/bus/iio/devices/iio:deviceX/in_activity_calibgender What: /sys/bus/iio/devices/iio:deviceX/in_energy_calibgender What: /sys/bus/iio/devices/iio:deviceX/in_distance_calibgender @@ -708,6 +749,7 @@ Description: 2.5kohm_to_gnd: connected to ground via a 2.5kOhm resistor, 6kohm_to_gnd: connected to ground via a 6kOhm resistor, 20kohm_to_gnd: connected to ground via a 20kOhm resistor, + 42kohm_to_gnd: connected to ground via a 42kOhm resistor, 90kohm_to_gnd: connected to ground via a 90kOhm resistor, 100kohm_to_gnd: connected to ground via an 100kOhm resistor, 125kohm_to_gnd: connected to ground via an 125kOhm resistor, @@ -2289,3 +2331,11 @@ KernelVersion: 6.7 Contact: linux-iio@vger.kernel.org Description: List of available timeout value for tap gesture confirmation. + +What: /sys/.../iio:deviceX/in_shunt_resistor +What: /sys/.../iio:deviceX/in_current_shunt_resistor +What: /sys/.../iio:deviceX/in_power_shunt_resistor +KernelVersion: 6.10 +Contact: linux-iio@vger.kernel.org +Description: + The value of current sense resistor in Ohms. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-adc-max9611 b/Documentation/ABI/testing/sysfs-bus-iio-adc-max9611 deleted file mode 100644 index 6d2d2b094941..000000000000 --- a/Documentation/ABI/testing/sysfs-bus-iio-adc-max9611 +++ /dev/null @@ -1,17 +0,0 @@ -What: /sys/bus/iio/devices/iio:deviceX/in_power_shunt_resistor -Date: March 2017 -KernelVersion: 4.12 -Contact: linux-iio@vger.kernel.org -Description: The value of the shunt resistor used to compute power drain on - common input voltage pin (RS+). In Ohms. - -What: /sys/bus/iio/devices/iio:deviceX/in_current_shunt_resistor -Date: March 2017 -KernelVersion: 4.12 -Contact: linux-iio@vger.kernel.org -Description: The value of the shunt resistor used to compute current flowing - between RS+ and RS- voltage sense inputs. In Ohms. - -These attributes describe a single physical component, exposed as two distinct -attributes as it is used to calculate two different values: power load and -current flowing between RS+ and RS- inputs. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-chemical-sgp40 b/Documentation/ABI/testing/sysfs-bus-iio-chemical-sgp40 index 469a7c00fad4..a95547e874f1 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-chemical-sgp40 +++ b/Documentation/ABI/testing/sysfs-bus-iio-chemical-sgp40 @@ -15,17 +15,3 @@ Description: Set the relative humidity. This value is sent to the sensor for humidity compensation. Default value: 50000 (50 % relative humidity) - -What: /sys/bus/iio/devices/iio:deviceX/in_resistance_calibbias -Date: August 2021 -KernelVersion: 5.15 -Contact: Andreas Klinger <ak@it-klinger.de> -Description: - Set the bias value for the resistance which is used for - calculation of in_concentration_input as follows: - - x = (in_resistance_raw - in_resistance_calibbias) * 0.65 - - in_concentration_input = 500 / (1 + e^x) - - Default value: 30000 diff --git a/Documentation/ABI/testing/sysfs-bus-iio-dac b/Documentation/ABI/testing/sysfs-bus-iio-dac new file mode 100644 index 000000000000..810eaac5533c --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-dac @@ -0,0 +1,61 @@ +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_toggle_en +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + Toggle enable. Write 1 to enable toggle or 0 to disable it. This + is useful when one wants to change the DAC output codes. For + autonomous toggling, the way it should be done is: + + - disable toggle operation; + - change out_currentY_rawN, where N is the integer value of the symbol; + - enable toggle operation. + +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_rawN +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + This attribute has the same meaning as out_currentY_raw. It is + specific to toggle enabled channels and refers to the DAC output + code in INPUT_N (_rawN), where N is the integer value of the symbol. + The same scale and offset as in out_currentY_raw applies. + +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_symbol +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + Performs a SW switch to a predefined output symbol. This attribute + is specific to toggle enabled channels and allows switching between + multiple predefined symbols. Each symbol corresponds to a different + output, denoted as out_currentY_rawN, where N is the integer value + of the symbol. Writing an integer value N will select out_currentY_rawN. + +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_toggle_en +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + Toggle enable. Write 1 to enable toggle or 0 to disable it. This + is useful when one wants to change the DAC output codes. For + autonomous toggling, the way it should be done is: + + - disable toggle operation; + - change out_voltageY_rawN, where N is the integer value of the symbol; + - enable toggle operation. + +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_rawN +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + This attribute has the same meaning as out_currentY_raw. It is + specific to toggle enabled channels and refers to the DAC output + code in INPUT_N (_rawN), where N is the integer value of the symbol. + The same scale and offset as in out_currentY_raw applies. + +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_symbol +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + Performs a SW switch to a predefined output symbol. This attribute + is specific to toggle enabled channels and allows switching between + multiple predefined symbols. Each symbol corresponds to a different + output, denoted as out_voltageY_rawN, where N is the integer value + of the symbol. Writing an integer value N will select out_voltageY_rawN. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-dac-ltc2688 b/Documentation/ABI/testing/sysfs-bus-iio-dac-ltc2688 index 1c35971277ba..ae95a5477382 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-dac-ltc2688 +++ b/Documentation/ABI/testing/sysfs-bus-iio-dac-ltc2688 @@ -53,34 +53,3 @@ KernelVersion: 5.18 Contact: linux-iio@vger.kernel.org Description: Returns the available values for the dither phase. - -What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_toggle_en -KernelVersion: 5.18 -Contact: linux-iio@vger.kernel.org -Description: - Toggle enable. Write 1 to enable toggle or 0 to disable it. This is - useful when one wants to change the DAC output codes. The way it should - be done is: - - - disable toggle operation; - - change out_voltageY_raw0 and out_voltageY_raw1; - - enable toggle operation. - -What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_raw0 -What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_raw1 -KernelVersion: 5.18 -Contact: linux-iio@vger.kernel.org -Description: - It has the same meaning as out_voltageY_raw. This attribute is - specific to toggle enabled channels and refers to the DAC output - code in INPUT_A (_raw0) and INPUT_B (_raw1). The same scale and offset - as in out_voltageY_raw applies. - -What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_symbol -KernelVersion: 5.18 -Contact: linux-iio@vger.kernel.org -Description: - Performs a SW toggle. This attribute is specific to toggle - enabled channels and allows to toggle between out_voltageY_raw0 - and out_voltageY_raw1 through software. Writing 0 will select - out_voltageY_raw0 while 1 selects out_voltageY_raw1. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-filter-admv8818 b/Documentation/ABI/testing/sysfs-bus-iio-filter-admv8818 index 31dbb390573f..c431f0a13cf5 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-filter-admv8818 +++ b/Documentation/ABI/testing/sysfs-bus-iio-filter-admv8818 @@ -3,7 +3,7 @@ KernelVersion: Contact: linux-iio@vger.kernel.org Description: Reading this returns the valid values that can be written to the - on_altvoltage0_mode attribute: + filter_mode attribute: - auto -> Adjust bandpass filter to track changes in input clock rate. - manual -> disable/unregister the clock rate notifier / input clock tracking. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc b/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc index 8916f7ec6507..8dbca113112d 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc +++ b/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc @@ -13,12 +13,3 @@ Description: available for reading data. However, samples can be occasionally skipped or repeated, depending on the beat between the capture and conversion rates. - -What: /sys/bus/iio/devices/iio:deviceX/in_shunt_resistor -Date: December 2015 -KernelVersion: 4.4 -Contact: linux-iio@vger.kernel.org -Description: - The value of the shunt resistor may be known only at runtime fom an - eeprom content read by a client application. This attribute allows to - set its value in ohms. diff --git a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml index d5cfa32ea52d..072b3c0c5fd0 100644 --- a/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml +++ b/Documentation/devicetree/bindings/extcon/extcon-ptn5150.yaml @@ -37,6 +37,11 @@ properties: GPIO pin (output) used to control VBUS. If skipped, no such control takes place. + port: + $ref: /schemas/graph.yaml#/properties/port + description: + A port node to link the usb controller for the dual role switch. + required: - compatible - interrupts @@ -58,5 +63,11 @@ examples: interrupt-parent = <&msmgpio>; interrupts = <78 IRQ_TYPE_LEVEL_HIGH>; vbus-gpios = <&msmgpio 148 GPIO_ACTIVE_HIGH>; + + port { + endpoint { + remote-endpoint = <&usb1_drd_sw>; + }; + }; }; }; diff --git a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt b/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt deleted file mode 100644 index dfc14f71e81f..000000000000 --- a/Documentation/devicetree/bindings/extcon/extcon-usb-gpio.txt +++ /dev/null @@ -1,21 +0,0 @@ -USB GPIO Extcon device - -This is a virtual device used to generate USB cable states from the USB ID pin -connected to a GPIO pin. - -Required properties: -- compatible: Should be "linux,extcon-usb-gpio" - -Either one of id-gpio or vbus-gpio must be present. Both can be present as well. -- id-gpio: gpio for USB ID pin. See gpio binding. -- vbus-gpio: gpio for USB VBUS pin. - -Example: Examples of extcon-usb-gpio node in dra7-evm.dts as listed below: - extcon_usb1 { - compatible = "linux,extcon-usb-gpio"; - id-gpio = <&gpio6 1 GPIO_ACTIVE_HIGH>; - } - - &omap_dwc3_1 { - extcon = <&extcon_usb1>; - }; diff --git a/Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yaml b/Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yaml new file mode 100644 index 000000000000..8856107bdd33 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/linux,extcon-usb-gpio.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/extcon/linux,extcon-usb-gpio.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: USB GPIO Extcon device + +maintainers: + - Frank Li <Frank.Li@nxp.com> + +description: + This is a virtual device used to generate USB cable states from the USB ID pin + connected to a GPIO pin. + +properties: + compatible: + const: linux,extcon-usb-gpio + + id-gpios: + description: gpio for USB ID pin. See gpio binding. + vbus-gpios: + description: gpio for USB VBUS pin. + +required: + - compatible + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + extcon_usb1 { + compatible = "linux,extcon-usb-gpio"; + id-gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/iio/accel/adi,adxl380.yaml b/Documentation/devicetree/bindings/iio/accel/adi,adxl380.yaml new file mode 100644 index 000000000000..f1ff5ff4f478 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/accel/adi,adxl380.yaml @@ -0,0 +1,92 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/accel/adi,adxl380.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices ADXL380/382 3-Axis Digital Accelerometer + +maintainers: + - Ramona Gradinariu <ramona.gradinariu@analog.com> + - Antoniu Miclaus <antoniu.miclaus@analog.com> + +description: | + The ADXL380/ADXL382 is a low noise density, low power, 3-axis + accelerometer with selectable measurement ranges. The ADXL380 + supports the ±4 g, ±8 g, and ±16 g ranges, and the ADXL382 supports + ±15 g, ±30 g, and ±60 g ranges. + + https://www.analog.com/en/products/adxl380.html + +properties: + compatible: + enum: + - adi,adxl380 + - adi,adxl382 + + reg: + maxItems: 1 + + interrupts: + minItems: 1 + maxItems: 2 + + interrupt-names: + minItems: 1 + items: + - enum: [INT0, INT1] + - const: INT1 + + vddio-supply: true + + vsupply-supply: true + +required: + - compatible + - reg + - interrupts + - interrupt-names + - vddio-supply + - vsupply-supply + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + + i2c { + #address-cells = <1>; + #size-cells = <0>; + + accelerometer@54 { + compatible = "adi,adxl380"; + reg = <0x54>; + vddio-supply = <&vddio>; + vsupply-supply = <&vsupply>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "INT0"; + }; + }; + - | + #include <dt-bindings/interrupt-controller/irq.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + accelerometer@0 { + compatible = "adi,adxl380"; + reg = <0>; + spi-max-frequency = <8000000>; + vddio-supply = <&vddio>; + vsupply-supply = <&vsupply>; + interrupt-parent = <&gpio>; + interrupts = <25 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "INT0"; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml index 6ddb03f61bd9..951a3a2ba8fc 100644 --- a/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml +++ b/Documentation/devicetree/bindings/iio/accel/kionix,kxcjk1013.yaml @@ -16,6 +16,7 @@ properties: - kionix,kxcj91008 - kionix,kxtj21009 - kionix,kxtf9 + - kionix,kx022-1020 - kionix,kx023-1025 reg: diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad4695.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad4695.yaml new file mode 100644 index 000000000000..310f046e139f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad4695.yaml @@ -0,0 +1,254 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/adi,ad4695.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices Easy Drive Multiplexed SAR Analog to Digital Converters + +maintainers: + - Michael Hennerich <Michael.Hennerich@analog.com> + - Nuno Sá <nuno.sa@analog.com> + +description: | + A family of similar multi-channel analog to digital converters with SPI bus. + + * https://www.analog.com/en/products/ad4695.html + * https://www.analog.com/en/products/ad4696.html + * https://www.analog.com/en/products/ad4697.html + * https://www.analog.com/en/products/ad4698.html + +$ref: /schemas/spi/spi-peripheral-props.yaml# + +properties: + compatible: + enum: + - adi,ad4695 + - adi,ad4696 + - adi,ad4697 + - adi,ad4698 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 80000000 + + spi-cpol: true + spi-cpha: true + + spi-rx-bus-width: + minimum: 1 + maximum: 4 + + avdd-supply: + description: Analog power supply. + + vio-supply: + description: I/O pin power supply. + + ldo-in-supply: + description: Internal LDO Input. Mutually exclusive with vdd-supply. + + vdd-supply: + description: Core power supply. Mutually exclusive with ldo-in-supply. + + ref-supply: + description: + External reference voltage. Mutually exclusive with refin-supply. + + refin-supply: + description: + Internal reference buffer input. Mutually exclusive with ref-supply. + + com-supply: + description: Common voltage supply for pseudo-differential analog inputs. + + adi,no-ref-current-limit: + $ref: /schemas/types.yaml#/definitions/flag + description: + When this flag is present, the REF Overvoltage Reduced Current protection + is disabled. + + adi,no-ref-high-z: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enable this flag if the ref-supply requires Reference Input High-Z Mode + to be disabled for proper operation. + + cnv-gpios: + description: The Convert Input (CNV). If omitted, CNV is tied to SPI CS. + maxItems: 1 + + reset-gpios: + description: The Reset Input (RESET). Should be configured GPIO_ACTIVE_LOW. + maxItems: 1 + + interrupts: + minItems: 1 + items: + - description: Signal coming from the BSY_ALT_GP0 pin (ALERT or BUSY). + - description: Signal coming from the GP2 pin (ALERT). + - description: Signal coming from the GP3 pin (BUSY). + + interrupt-names: + minItems: 1 + items: + - const: gp0 + - const: gp2 + - const: gp3 + + gpio-controller: true + + "#gpio-cells": + const: 2 + description: | + The first cell is the GPn number: 0 to 3. + The second cell takes standard GPIO flags. + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^in(?:[13579]|1[135])-supply$": + description: + Optional voltage supply for odd numbered channels when they are used as + the negative input for a pseudo-differential channel. + + "^channel@[0-9a-f]$": + type: object + $ref: adc.yaml + unevaluatedProperties: false + description: + Describes each individual channel. In addition the properties defined + below, bipolar from adc.yaml is also supported. + + properties: + reg: + maximum: 15 + + common-mode-channel: + description: + Describes the common mode channel for single channels. 0xFF is REFGND + and OxFE is COM. Macros are available for these values in + dt-bindings/iio/adi,ad4695.h. Values 1 to 15 correspond to INx inputs. + Only odd numbered INx inputs can be used as common mode channels. + enum: [1, 3, 5, 7, 9, 11, 13, 15, 0xFE, 0xFF] + default: 0xFF + + adi,no-high-z: + $ref: /schemas/types.yaml#/definitions/flag + description: + Enable this flag if the input pin requires the Analog Input High-Z + Mode to be disabled for proper operation. + + required: + - reg + + allOf: + # bipolar mode can't be used with REFGND + - if: + properties: + common-mode-channel: + const: 0xFF + then: + properties: + bipolar: false + +required: + - compatible + - reg + - avdd-supply + - vio-supply + +allOf: + - oneOf: + - required: + - ldo-in-supply + - required: + - vdd-supply + + - oneOf: + - required: + - ref-supply + - required: + - refin-supply + + # the internal reference buffer always requires high-z mode + - if: + required: + - refin-supply + then: + properties: + adi,no-ref-high-z: false + + # limit channels for 8-channel chips + - if: + properties: + compatible: + contains: + enum: + - adi,ad4697 + - adi,ad4698 + then: + patternProperties: + "^in(?:9|1[135])-supply$": false + "^channel@[0-7]$": + properties: + reg: + maximum: 7 + common-mode-channel: + enum: [1, 3, 5, 7, 0xFE, 0xFF] + "^channel@[8-9a-f]$": false + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/iio/adi,ad4695.h> + + spi { + #address-cells = <1>; + #size-cells = <0>; + + adc@0 { + compatible = "adi,ad4695"; + reg = <0>; + spi-cpol; + spi-cpha; + spi-max-frequency = <80000000>; + avdd-supply = <&power_supply>; + ldo-in-supply = <&power_supply>; + vio-supply = <&io_supply>; + refin-supply = <&supply_5V>; + com-supply = <&supply_2V5>; + in3-supply = <&supply_2V5>; + reset-gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + + #address-cells = <1>; + #size-cells = <0>; + + /* Pseudo-differential channel between IN0 and REFGND. */ + channel@0 { + reg = <0>; + }; + + /* Pseudo-differential channel between IN1 and COM. */ + channel@1 { + reg = <1>; + common-mode-channel = <AD4695_COMMON_MODE_COM>; + bipolar; + }; + + /* Pseudo-differential channel between IN2 and IN3. */ + channel@2 { + reg = <2>; + common-mode-channel = <3>; + bipolar; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml index 190889c7b62a..66dd1c549bd3 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7192.yaml @@ -39,11 +39,21 @@ properties: clocks: maxItems: 1 - description: phandle to the master clock (mclk) + description: + Optionally, either a crystal can be attached externally between MCLK1 and + MCLK2 pins, or an external CMOS-compatible clock can drive the MCLK2 + pin. If absent, internal 4.92MHz clock is used, which can be made + available on MCLK2 pin. clock-names: - items: - - const: mclk + enum: + - xtal + - mclk + + "#clock-cells": + const: 0 + description: + If present when internal clock is used, configured as clock provider. interrupts: maxItems: 1 @@ -134,8 +144,6 @@ patternProperties: required: - compatible - reg - - clocks - - clock-names - interrupts - dvdd-supply - avdd-supply @@ -156,6 +164,18 @@ allOf: then: patternProperties: "^channel@[0-9a-f]+$": false + - if: + anyOf: + - required: + - clocks + - required: + - clock-names + then: + properties: + "#clock-cells": false + required: + - clocks + - clock-names unevaluatedProperties: false @@ -201,8 +221,7 @@ examples: spi-max-frequency = <1000000>; spi-cpol; spi-cpha; - clocks = <&ad7192_mclk>; - clock-names = "mclk"; + #clock-cells = <0>; interrupts = <25 0x2>; interrupt-parent = <&gpio>; aincom-supply = <&aincom>; diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7380.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7380.yaml index 899b777017ce..bd19abb867d9 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7380.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7380.yaml @@ -15,10 +15,17 @@ description: | * https://www.analog.com/en/products/ad7381.html * https://www.analog.com/en/products/ad7383.html * https://www.analog.com/en/products/ad7384.html + * https://www.analog.com/en/products/ad7386.html + * https://www.analog.com/en/products/ad7387.html + * https://www.analog.com/en/products/ad7388.html * https://www.analog.com/en/products/ad7380-4.html * https://www.analog.com/en/products/ad7381-4.html * https://www.analog.com/en/products/ad7383-4.html * https://www.analog.com/en/products/ad7384-4.html + * https://www.analog.com/en/products/ad7386-4.html + * https://www.analog.com/en/products/ad7387-4.html + * https://www.analog.com/en/products/ad7388-4.html + $ref: /schemas/spi/spi-peripheral-props.yaml# @@ -29,10 +36,16 @@ properties: - adi,ad7381 - adi,ad7383 - adi,ad7384 + - adi,ad7386 + - adi,ad7387 + - adi,ad7388 - adi,ad7380-4 - adi,ad7381-4 - adi,ad7383-4 - adi,ad7384-4 + - adi,ad7386-4 + - adi,ad7387-4 + - adi,ad7388-4 reg: maxItems: 1 diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml index 00fdaed11cbd..69408cae3db9 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad7606.yaml @@ -35,65 +35,83 @@ properties: avcc-supply: true + vdrive-supply: + description: + Determines the voltage level at which the interface logic pins will + operate. + + refin-supply: + description: + The voltage supply for optional external reference voltage. + interrupts: + description: + The BUSY pin falling edge indicates that the conversion is over, and thus + new data is available. maxItems: 1 adi,conversion-start-gpios: description: - Must be the device tree identifier of the CONVST pin. - This logic input is used to initiate conversions on the analog - input channels. As the line is active high, it should be marked - GPIO_ACTIVE_HIGH. - maxItems: 1 + Must be the device tree identifier of the CONVST pin(s). This logic input + is used to initiate conversions on the analog input channels. As the line + is active high, it should be marked GPIO_ACTIVE_HIGH. + minItems: 1 + maxItems: 2 reset-gpios: description: - Must be the device tree identifier of the RESET pin. If specified, - it will be asserted during driver probe. As the line is active high, - it should be marked GPIO_ACTIVE_HIGH. + Must be the device tree identifier of the RESET pin. If specified, it will + be asserted during driver probe. On the AD7606x, as the line is active + high, it should be marked GPIO_ACTIVE_HIGH. On the AD7616, as the line is + active low, it should be marked GPIO_ACTIVE_LOW. maxItems: 1 standby-gpios: description: - Must be the device tree identifier of the STBY pin. This pin is used - to place the AD7606 into one of two power-down modes, Standby mode or + Must be the device tree identifier of the STBY pin. This pin is used to + place the AD7606 into one of two power-down modes, Standby mode or Shutdown mode. As the line is active low, it should be marked GPIO_ACTIVE_LOW. maxItems: 1 adi,first-data-gpios: description: - Must be the device tree identifier of the FRSTDATA pin. - The FRSTDATA output indicates when the first channel, V1, is - being read back on either the parallel, byte or serial interface. - As the line is active high, it should be marked GPIO_ACTIVE_HIGH. + Must be the device tree identifier of the FRSTDATA pin. The FRSTDATA + output indicates when the first channel, V1, is being read back on either + the parallel, byte or serial interface. As the line is active high, it + should be marked GPIO_ACTIVE_HIGH. maxItems: 1 adi,range-gpios: description: - Must be the device tree identifier of the RANGE pin. The polarity on - this pin determines the input range of the analog input channels. If - this pin is tied to a logic high, the analog input range is ±10V for - all channels. If this pin is tied to a logic low, the analog input range + Must be the device tree identifier of the RANGE pin. The state on this + pin determines the input range of the analog input channels. If this pin + is tied to a logic high, the analog input range is ±10V for all channels. + On the AD760X, if this pin is tied to a logic low, the analog input range is ±5V for all channels. As the line is active high, it should be marked - GPIO_ACTIVE_HIGH. - maxItems: 1 + GPIO_ACTIVE_HIGH. On the AD7616, there are 2 pins, and if the 2 pins are + tied to a logic high, software mode is enabled, otherwise one of the 3 + possible range values is selected. + minItems: 1 + maxItems: 2 adi,oversampling-ratio-gpios: description: - Must be the device tree identifier of the over-sampling - mode pins. As the line is active high, it should be marked - GPIO_ACTIVE_HIGH. + Must be the device tree identifier of the over-sampling mode pins. As the + line is active high, it should be marked GPIO_ACTIVE_HIGH. On the AD7606X + parts that support it, if all 3 pins are tied to a logic high, software + mode is enabled. maxItems: 3 adi,sw-mode: description: - Software mode of operation, so far available only for ad7616 and ad7606b. - It is enabled when all three oversampling mode pins are connected to - high level. The device is configured by the corresponding registers. If the - adi,oversampling-ratio-gpios property is defined, then the driver will set the - oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired - to VDD. + Software mode of operation, so far available only for AD7616 and AD7606B. + It is enabled when all three oversampling mode pins are connected to high + level for the AD7606B, or both the range selection are connected to high + level for the AD7616. The device is configured by the corresponding + registers. If the adi,oversampling-ratio-gpios property is defined, then + the driver will set the oversampling gpios to high. Otherwise, it is + assumed that the pins are hardwired to VDD. type: boolean required: @@ -101,12 +119,57 @@ required: - reg - spi-cpha - avcc-supply + - vdrive-supply - interrupts - adi,conversion-start-gpios allOf: - $ref: /schemas/spi/spi-peripheral-props.yaml# + - if: + properties: + compatible: + contains: + const: adi,ad7616 + then: + properties: + adi,first-data-gpios: false + standby-gpios: false + adi,range-gpios: + maxItems: 2 + else: + properties: + adi,range-gpios: + maxItems: 1 + + - if: + properties: + compatible: + contains: + enum: + - adi,ad7605-4 + - adi,ad7616 + then: + properties: + adi,oversampling-ratio-gpios: false + + - if: + properties: + compatible: + contains: + enum: + - adi,ad7605-4 + - adi,ad7606-4 + - adi,ad7606-6 + - adi,ad7606-8 + then: + properties: + adi,sw-mode: false + else: + properties: + adi,conversion-start-gpios: + maxItems: 1 + unevaluatedProperties: false examples: @@ -125,6 +188,7 @@ examples: spi-cpha; avcc-supply = <&adc_vref>; + vdrive-supply = <&vdd_supply>; interrupts = <25 IRQ_TYPE_EDGE_FALLING>; interrupt-parent = <&gpio>; @@ -136,7 +200,6 @@ examples: <&gpio 23 GPIO_ACTIVE_HIGH>, <&gpio 26 GPIO_ACTIVE_HIGH>; standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>; - adi,sw-mode; }; }; ... diff --git a/Documentation/devicetree/bindings/iio/adc/adi,ad9467.yaml b/Documentation/devicetree/bindings/iio/adc/adi,ad9467.yaml index eecd5fbab695..2606c0c5dfc6 100644 --- a/Documentation/devicetree/bindings/iio/adc/adi,ad9467.yaml +++ b/Documentation/devicetree/bindings/iio/adc/adi,ad9467.yaml @@ -28,6 +28,9 @@ properties: - adi,ad9265 - adi,ad9434 - adi,ad9467 + - adi,ad9643 + - adi,ad9649 + - adi,ad9652 reg: maxItems: 1 diff --git a/Documentation/devicetree/bindings/iio/adc/microchip,pac1921.yaml b/Documentation/devicetree/bindings/iio/adc/microchip,pac1921.yaml new file mode 100644 index 000000000000..12e56b1b3d3f --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/microchip,pac1921.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/microchip,pac1921.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip PAC1921 High-Side Power/Current Monitor with Anaog Output + +maintainers: + - Matteo Martelli <matteomartelli3@gmail.com> + +description: | + The PAC1921 is a power/current monitoring device with an analog output + and I2C/SMBus interface. + + Datasheet can be found here: + https://ww1.microchip.com/downloads/en/DeviceDoc/PAC1921-Data-Sheet-DS20005293E.pdf + +properties: + compatible: + const: microchip,pac1921 + + reg: + maxItems: 1 + + vdd-supply: true + + "#io-channel-cells": + const: 1 + + shunt-resistor-micro-ohms: + description: + Value in micro Ohms of the shunt resistor connected between + the SENSE+ and SENSE- inputs, across which the current is measured. + Value is needed to compute the scaling of the measured current. + + label: + description: Unique name to identify which device this is. + + read-integrate-gpios: + description: + READ/INT input pin to control the current state of the device, either in + the INTEGRATE state when driven high, or in the READ state when driven low. + When not connected the pin is floating and it can be overridden by the + INT_EN register bit after asserting the READ/INT_OVR register bit. + maxItems: 1 + +required: + - compatible + - reg + - vdd-supply + - shunt-resistor-micro-ohms + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + adc@4c { + compatible = "microchip,pac1921"; + reg = <0x4c>; + vdd-supply = <&vdd>; + #io-channel-cells = <1>; + label = "vbat"; + shunt-resistor-micro-ohms = <10000>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.yaml b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.yaml index aa24b841393c..fd93ed3991e0 100644 --- a/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/rockchip-saradc.yaml @@ -17,6 +17,9 @@ properties: - const: rockchip,rk3399-saradc - const: rockchip,rk3588-saradc - items: + - const: rockchip,rk3576-saradc + - const: rockchip,rk3588-saradc + - items: - enum: - rockchip,px30-saradc - rockchip,rk3308-saradc diff --git a/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.yaml b/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.yaml index cab0d425eaa4..c3a116427dc3 100644 --- a/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.yaml +++ b/Documentation/devicetree/bindings/iio/adc/sigma-delta-modulator.yaml @@ -18,18 +18,39 @@ properties: - sd-modulator - ads1201 + '#io-backend-cells': + const: 0 + '#io-channel-cells': const: 0 + vref-supply: + description: Phandle to the vref input analog reference voltage. + +dependencies: + vref-supply: [ '#io-backend-cells' ] + required: - compatible - - '#io-channel-cells' + +anyOf: + - required: ['#io-backend-cells'] + - required: ['#io-channel-cells'] additionalProperties: false examples: - | - ads1202: adc { + // Backend binding example. SD modulator configured as an IIO backend device + ads1201_0: adc { + compatible = "sd-modulator"; + vref-supply = <&vdd_adc>; + #io-backend-cells = <0>; + }; + + - | + // Legacy binding example. SD modulator configured as an IIO channel provider + ads1201_1: adc { compatible = "sd-modulator"; #io-channel-cells = <0>; }; diff --git a/Documentation/devicetree/bindings/iio/adc/sophgo,cv1800b-saradc.yaml b/Documentation/devicetree/bindings/iio/adc/sophgo,cv1800b-saradc.yaml new file mode 100644 index 000000000000..f652b98615f7 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/adc/sophgo,cv1800b-saradc.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/adc/sophgo,cv1800b-saradc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: + Sophgo CV1800B SoC 3 channels Successive Approximation Analog to + Digital Converters + +maintainers: + - Thomas Bonnefille <thomas.bonnefille@bootlin.com> + +description: + Datasheet at https://github.com/sophgo/sophgo-doc/releases + +properties: + compatible: + const: sophgo,cv1800b-saradc + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + "^channel@[0-2]$": + $ref: adc.yaml + + properties: + reg: + items: + - minimum: 0 + maximum: 2 + + required: + - reg + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - '#address-cells' + - '#size-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sophgo,cv1800.h> + #include <dt-bindings/interrupt-controller/irq.h> + adc@30f0000 { + compatible = "sophgo,cv1800b-saradc"; + reg = <0x030f0000 0x1000>; + clocks = <&clk CLK_SARADC>; + interrupts = <100 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { + reg = <0>; + }; + + channel@1 { + reg = <1>; + }; + + channel@2 { + reg = <2>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml index ec34c48d4878..ef9dcc365eab 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-adc.yaml @@ -54,7 +54,9 @@ properties: It's not present on stm32f4. It's required on stm32h7 and stm32mp1. - clock-names: true + clock-names: + minItems: 1 + maxItems: 2 st,max-clk-rate-hz: description: diff --git a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml index 2722edab1d9a..c24ac98bbb3d 100644 --- a/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/st,stm32-dfsdm-adc.yaml @@ -102,9 +102,11 @@ patternProperties: items: minimum: 0 maximum: 7 + deprecated: true st,adc-channel-names: description: List of single-ended channel names. + deprecated: true st,filter-order: description: | @@ -118,6 +120,12 @@ patternProperties: "#io-channel-cells": const: 1 + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + st,adc-channel-types: description: | Single-ended channel input type. @@ -128,6 +136,7 @@ patternProperties: items: enum: [ SPI_R, SPI_F, MANCH_R, MANCH_F ] $ref: /schemas/types.yaml#/definitions/non-unique-string-array + deprecated: true st,adc-channel-clk-src: description: | @@ -139,6 +148,7 @@ patternProperties: items: enum: [ CLKIN, CLKOUT, CLKOUT_F, CLKOUT_R ] $ref: /schemas/types.yaml#/definitions/non-unique-string-array + deprecated: true st,adc-alt-channel: description: @@ -147,6 +157,7 @@ patternProperties: If not set, channel n is connected to SPI input n. If set, channel n is connected to SPI input n + 1. type: boolean + deprecated: true st,filter0-sync: description: @@ -165,11 +176,60 @@ patternProperties: - compatible - reg - interrupts - - st,adc-channels - - st,adc-channel-names - st,filter-order - "#io-channel-cells" + patternProperties: + "^channel@[0-7]$": + type: object + $ref: adc.yaml + unevaluatedProperties: false + description: Represents the external channels which are connected to the DFSDM. + + properties: + reg: + maximum: 7 + + label: + description: + Unique name to identify which channel this is. + + st,adc-channel-type: + description: | + Single-ended channel input type. + - "SPI_R": SPI with data on rising edge (default) + - "SPI_F": SPI with data on falling edge + - "MANCH_R": manchester codec, rising edge = logic 0, falling edge = logic 1 + - "MANCH_F": manchester codec, rising edge = logic 1, falling edge = logic 0 + $ref: /schemas/types.yaml#/definitions/string + enum: [ SPI_R, SPI_F, MANCH_R, MANCH_F ] + + st,adc-channel-clk-src: + description: | + Conversion clock source. + - "CLKIN": external SPI clock (CLKIN x) + - "CLKOUT": internal SPI clock (CLKOUT) (default) + - "CLKOUT_F": internal SPI clock divided by 2 (falling edge). + - "CLKOUT_R": internal SPI clock divided by 2 (rising edge). + $ref: /schemas/types.yaml#/definitions/string + enum: [ CLKIN, CLKOUT, CLKOUT_F, CLKOUT_R ] + + st,adc-alt-channel: + description: + Must be defined if two sigma delta modulators are + connected on same SPI input. + If not set, channel n is connected to SPI input n. + If set, channel n is connected to SPI input n + 1. + type: boolean + + io-backends: + description: + Used to pipe external sigma delta modulator or internal ADC backend to DFSDM channel. + maxItems: 1 + + required: + - reg + allOf: - if: properties: @@ -199,9 +259,19 @@ patternProperties: description: From common IIO binding. Used to pipe external sigma delta modulator or internal ADC output to DFSDM channel. + deprecated: true - required: - - io-channels + if: + required: + - st,adc-channels + then: + required: + - io-channels + + patternProperties: + "^channel@[0-7]$": + required: + - io-backends - if: properties: @@ -298,6 +368,7 @@ examples: #address-cells = <1>; #size-cells = <0>; + // Example 1: Audio use case with generic binding dfsdm0: filter@0 { compatible = "st,stm32-dfsdm-dmic"; reg = <0>; @@ -305,12 +376,18 @@ examples: dmas = <&dmamux1 101 0x400 0x01>; dma-names = "rx"; #io-channel-cells = <1>; - st,adc-channels = <1>; - st,adc-channel-names = "dmic0"; - st,adc-channel-types = "SPI_R"; - st,adc-channel-clk-src = "CLKOUT"; + #address-cells = <1>; + #size-cells = <0>; st,filter-order = <5>; + channel@1 { + reg = <1>; + label = "dmic0"; + st,adc-channel-type = "SPI_R"; + st,adc-channel-clk-src = "CLKOUT"; + st,adc-alt-channel; + }; + asoc_pdm0: dfsdm-dai { compatible = "st,stm32h7-dfsdm-dai"; #sound-dai-cells = <0>; @@ -318,19 +395,34 @@ examples: }; }; - dfsdm_pdm1: filter@1 { + // Example 2: Analog use case with generic binding + dfsdm1: filter@1 { compatible = "st,stm32-dfsdm-adc"; reg = <1>; interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; dmas = <&dmamux1 102 0x400 0x01>; dma-names = "rx"; - #io-channel-cells = <1>; - st,adc-channels = <2 3>; - st,adc-channel-names = "in2", "in3"; - st,adc-channel-types = "SPI_R", "SPI_R"; - st,adc-channel-clk-src = "CLKOUT_F", "CLKOUT_F"; - io-channels = <&sd_adc2 &sd_adc3>; st,filter-order = <1>; + #io-channel-cells = <1>; + #address-cells = <1>; + #size-cells = <0>; + + channel@2 { + reg = <2>; + label = "in2"; + st,adc-channel-type = "SPI_F"; + st,adc-channel-clk-src = "CLKOUT"; + st,adc-alt-channel; + io-backends = <&sd_adc2>; + }; + + channel@3 { + reg = <3>; + label = "in3"; + st,adc-channel-type = "SPI_R"; + st,adc-channel-clk-src = "CLKOUT"; + io-backends = <&sd_adc3>; + }; }; }; diff --git a/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml index d40689f233f2..1caa896fce82 100644 --- a/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml +++ b/Documentation/devicetree/bindings/iio/adc/x-powers,axp209-adc.yaml @@ -37,6 +37,17 @@ description: | 3 | batt_dischrg_i 4 | ts_v + AXP717 + ------ + 0 | batt_v + 1 | ts_v + 2 | vbus_v + 3 | vsys_v + 4 | pmic_temp + 5 | batt_chrg_i + 6 | vmid_v + 7 | bkup_batt_v + AXP813 ------ 0 | pmic_temp @@ -52,6 +63,7 @@ properties: oneOf: - const: x-powers,axp209-adc - const: x-powers,axp221-adc + - const: x-powers,axp717-adc - const: x-powers,axp813-adc - items: diff --git a/Documentation/devicetree/bindings/iio/dac/adi,ltc2664.yaml b/Documentation/devicetree/bindings/iio/dac/adi,ltc2664.yaml new file mode 100644 index 000000000000..33490853497b --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/adi,ltc2664.yaml @@ -0,0 +1,181 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/adi,ltc2664.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices LTC2664 DAC + +maintainers: + - Michael Hennerich <michael.hennerich@analog.com> + - Kim Seer Paller <kimseer.paller@analog.com> + +description: | + Analog Devices LTC2664 4 channel, 12-/16-Bit, +-10V DAC + https://www.analog.com/media/en/technical-documentation/data-sheets/2664fa.pdf + +properties: + compatible: + enum: + - adi,ltc2664 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 50000000 + + vcc-supply: + description: Analog Supply Voltage Input. + + v-pos-supply: + description: Positive Supply Voltage Input. + + v-neg-supply: + description: Negative Supply Voltage Input. + + iovcc-supply: + description: Digital Input/Output Supply Voltage. + + ref-supply: + description: + Reference Input/Output. The voltage at the REF pin sets the full-scale + range of all channels. If not provided the internal reference is used and + also provided on the VREF pin. + + reset-gpios: + description: + Active-low Asynchronous Clear Input. A logic low at this level-triggered + input clears the part to the reset code and range determined by the + hardwired option chosen using the MSPAN pins. The control registers are + cleared to zero. + maxItems: 1 + + adi,manual-span-operation-config: + description: + This property must mimic the MSPAN pin configurations. By tying the MSPAN + pins (MSP2, MSP1 and MSP0) to GND and/or VCC, any output range can be + hardware-configured with different mid-scale or zero-scale reset options. + The hardware configuration is latched during power on reset for proper + operation. + 0 - MPS2=GND, MPS1=GND, MSP0=GND (+-10V, reset to 0V) + 1 - MPS2=GND, MPS1=GND, MSP0=VCC (+-5V, reset to 0V) + 2 - MPS2=GND, MPS1=VCC, MSP0=GND (+-2.5V, reset to 0V) + 3 - MPS2=GND, MPS1=VCC, MSP0=VCC (0V to 10, reset to 0V) + 4 - MPS2=VCC, MPS1=GND, MSP0=GND (0V to 10V, reset to 5V) + 5 - MPS2=VCC, MPS1=GND, MSP0=VCC (0V to 5V, reset to 0V) + 6 - MPS2=VCC, MPS1=VCC, MSP0=GND (0V to 5V, reset to 2.5V) + 7 - MPS2=VCC, MPS1=VCC, MSP0=VCC (0V to 5V, reset to 0V, enables SoftSpan) + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6, 7] + default: 7 + + io-channels: + description: + ADC channel to monitor voltages and temperature at the MUXOUT pin. + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + "^channel@[0-3]$": + $ref: dac.yaml + type: object + additionalProperties: false + + properties: + reg: + description: The channel number representing the DAC output channel. + maximum: 3 + + adi,toggle-mode: + description: + Set the channel as a toggle enabled channel. Toggle operation enables + fast switching of a DAC output between two different DAC codes without + any SPI transaction. + type: boolean + + output-range-microvolt: + description: + This property is only allowed when SoftSpan is enabled. If not present, + [0, 5000000] is the default output range. + oneOf: + - items: + - const: 0 + - enum: [5000000, 10000000] + - items: + - const: -5000000 + - const: 5000000 + - items: + - const: -10000000 + - const: 10000000 + - items: + - const: -2500000 + - const: 2500000 + + required: + - reg + + allOf: + - if: + not: + properties: + adi,manual-span-operation-config: + const: 7 + then: + patternProperties: + "^channel@[0-3]$": + properties: + output-range-microvolt: false + +required: + - compatible + - reg + - spi-max-frequency + - vcc-supply + - iovcc-supply + - v-pos-supply + - v-neg-supply + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +additionalProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + dac@0 { + compatible = "adi,ltc2664"; + reg = <0>; + spi-max-frequency = <10000000>; + + vcc-supply = <&vcc>; + iovcc-supply = <&vcc>; + ref-supply = <&vref>; + v-pos-supply = <&vpos>; + v-neg-supply = <&vneg>; + + io-channels = <&adc 0>; + + #address-cells = <1>; + #size-cells = <0>; + channel@0 { + reg = <0>; + adi,toggle-mode; + output-range-microvolt = <(-10000000) 10000000>; + }; + + channel@1 { + reg = <1>; + output-range-microvolt= <0 10000000>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/adi,ltc2672.yaml b/Documentation/devicetree/bindings/iio/dac/adi,ltc2672.yaml new file mode 100644 index 000000000000..c8c434c10643 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/adi,ltc2672.yaml @@ -0,0 +1,160 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/adi,ltc2672.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices LTC2672 DAC + +maintainers: + - Michael Hennerich <michael.hennerich@analog.com> + - Kim Seer Paller <kimseer.paller@analog.com> + +description: | + Analog Devices LTC2672 5 channel, 12-/16-Bit, 300mA DAC + https://www.analog.com/media/en/technical-documentation/data-sheets/ltc2672.pdf + +properties: + compatible: + enum: + - adi,ltc2672 + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 50000000 + + vcc-supply: + description: Analog Supply Voltage Input. + + v-neg-supply: + description: Negative Supply Voltage Input. + + vdd0-supply: + description: Positive Supply Voltage Input for DAC OUT0. + + vdd1-supply: + description: Positive Supply Voltage Input for DAC OUT1. + + vdd2-supply: + description: Positive Supply Voltage Input for DAC OUT2. + + vdd3-supply: + description: Positive Supply Voltage Input for DAC OUT3. + + vdd4-supply: + description: Positive Supply Voltage Input for DAC OUT4. + + iovcc-supply: + description: Digital Input/Output Supply Voltage. + + ref-supply: + description: + Reference Input/Output. The voltage at the REF pin sets the full-scale + range of all channels. If not provided the internal reference is used and + also provided on the VREF pin. + + reset-gpios: + description: + Active Low Asynchronous Clear Input. A logic low at this level triggered + input clears the device to the default reset code and output range, which + is zero-scale with the outputs off. The control registers are cleared to + zero. + maxItems: 1 + + adi,rfsadj-ohms: + description: + If FSADJ is tied to VCC, an internal RFSADJ (20 kΩ) is selected, which + results in nominal output ranges. When an external resistor of 19 kΩ to + 41 kΩ can be used instead by connecting the resistor between FSADJ and GND + it controls the scaling of the ranges, and the internal resistor is + automatically disconnected. + minimum: 19000 + maximum: 41000 + default: 20000 + + io-channels: + description: + ADC channel to monitor voltages and currents at the MUX pin. + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + +patternProperties: + "^channel@[0-4]$": + $ref: dac.yaml + type: object + additionalProperties: false + + properties: + reg: + description: The channel number representing the DAC output channel. + maximum: 4 + + adi,toggle-mode: + description: + Set the channel as a toggle enabled channel. Toggle operation enables + fast switching of a DAC output between two different DAC codes without + any SPI transaction. + type: boolean + + output-range-microamp: + items: + - const: 0 + - enum: [3125000, 6250000, 12500000, 25000000, 50000000, 100000000, + 200000000, 300000000] + + required: + - reg + - output-range-microamp + +required: + - compatible + - reg + - spi-max-frequency + - vcc-supply + - iovcc-supply + - v-neg-supply + +allOf: + - $ref: /schemas/spi/spi-peripheral-props.yaml# + +additionalProperties: false + +examples: + - | + spi { + #address-cells = <1>; + #size-cells = <0>; + dac@0 { + compatible = "adi,ltc2672"; + reg = <0>; + spi-max-frequency = <10000000>; + + vcc-supply = <&vcc>; + iovcc-supply = <&vcc>; + ref-supply = <&vref>; + v-neg-supply = <&vneg>; + + io-channels = <&adc 0>; + + #address-cells = <1>; + #size-cells = <0>; + channel@0 { + reg = <0>; + adi,toggle-mode; + output-range-microamp = <0 3125000>; + }; + + channel@1 { + reg = <1>; + output-range-microamp = <0 6250000>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/iio/dac/dac.yaml b/Documentation/devicetree/bindings/iio/dac/dac.yaml new file mode 100644 index 000000000000..daa40724e1cf --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/dac.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/dac.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: IIO Common Properties for DAC Channels + +maintainers: + - Jonathan Cameron <jic23@kernel.org> + +description: + A few properties are defined in a common way for DAC channels. + +properties: + $nodename: + pattern: "^channel(@[0-9a-f]+)?$" + description: + A channel index should match reg. + + reg: + maxItems: 1 + + label: + description: Unique name to identify which channel this is. + + output-range-microamp: + maxItems: 2 + minItems: 2 + description: + Specify the channel output full scale range in microamperes. + + output-range-microvolt: + maxItems: 2 + minItems: 2 + description: + Specify the channel output full scale range in microvolts. + +anyOf: + - oneOf: + - required: + - reg + - output-range-microamp + - required: + - reg + - output-range-microvolt + - required: + - reg + +additionalProperties: true diff --git a/Documentation/devicetree/bindings/iio/frequency/adi,adf4377.yaml b/Documentation/devicetree/bindings/iio/frequency/adi,adf4377.yaml index aa6a3193b4e0..5f950ee9aec7 100644 --- a/Documentation/devicetree/bindings/iio/frequency/adi,adf4377.yaml +++ b/Documentation/devicetree/bindings/iio/frequency/adi,adf4377.yaml @@ -17,6 +17,7 @@ description: | applications. https://www.analog.com/en/products/adf4377.html + https://www.analog.com/en/products/adf4378.html properties: compatible: @@ -73,6 +74,15 @@ required: allOf: - $ref: /schemas/spi/spi-peripheral-props.yaml# + - if: + properties: + compatible: + contains: + enum: + - adi,adf4378 + then: + properties: + clk2-enable-gpios: false unevaluatedProperties: false diff --git a/Documentation/devicetree/bindings/iio/humidity/sciosense,ens210.yaml b/Documentation/devicetree/bindings/iio/humidity/sciosense,ens210.yaml new file mode 100644 index 000000000000..ed0ea938f7f8 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/humidity/sciosense,ens210.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/humidity/sciosense,ens210.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ScioSense ENS210 temperature and humidity sensor + +maintainers: + - Joshua Felmeden <jfelmeden@thegoodpenguin.co.uk> + +description: | + Temperature and Humidity sensor. + + Datasheet: + https://www.sciosense.com/wp-content/uploads/2024/04/ENS21x-Datasheet.pdf + https://www.sciosense.com/wp-content/uploads/2023/12/ENS210-Datasheet.pdf + +properties: + compatible: + oneOf: + - items: + - enum: + - sciosense,ens210a + - sciosense,ens211 + - sciosense,ens212 + - sciosense,ens213a + - sciosense,ens215 + - const: sciosense,ens210 + - const: sciosense,ens210 + + reg: + maxItems: 1 + + vdd-supply: true + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + temperature-sensor@43 { + compatible = "sciosense,ens210"; + reg = <0x43>; + }; + }; +... + diff --git a/Documentation/devicetree/bindings/iio/light/liteon,ltrf216a.yaml b/Documentation/devicetree/bindings/iio/light/liteon,ltrf216a.yaml index 7de1b0e721ca..877e955d4ebd 100644 --- a/Documentation/devicetree/bindings/iio/light/liteon,ltrf216a.yaml +++ b/Documentation/devicetree/bindings/iio/light/liteon,ltrf216a.yaml @@ -14,7 +14,9 @@ description: properties: compatible: - const: liteon,ltrf216a + enum: + - liteon,ltr308 + - liteon,ltrf216a reg: maxItems: 1 diff --git a/Documentation/devicetree/bindings/iio/light/rohm,bh1745.yaml b/Documentation/devicetree/bindings/iio/light/rohm,bh1745.yaml new file mode 100644 index 000000000000..44896795c67e --- /dev/null +++ b/Documentation/devicetree/bindings/iio/light/rohm,bh1745.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/light/rohm,bh1745.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ROHM BH1745 colour sensor + +maintainers: + - Mudit Sharma <muditsharma.info@gmail.com> + +description: + BH1745 is an I2C colour sensor with red, green, blue and clear + channels. It has a programmable active low interrupt pin. + Interrupt occurs when the signal from the selected interrupt + source channel crosses set interrupt threshold high/low level. + +properties: + compatible: + const: rohm,bh1745 + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + vdd-supply: true + +required: + - compatible + - reg + - vdd-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + + colour-sensor@38 { + compatible = "rohm,bh1745"; + reg = <0x38>; + interrupt-parent = <&gpio>; + interrupts = <19 IRQ_TYPE_LEVEL_LOW>; + vdd-supply = <&vdd>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/iio/light/rohm,bu27034.yaml b/Documentation/devicetree/bindings/iio/light/rohm,bu27034anuc.yaml index 30a109a1bf3b..29c90ca5b258 100644 --- a/Documentation/devicetree/bindings/iio/light/rohm,bu27034.yaml +++ b/Documentation/devicetree/bindings/iio/light/rohm,bu27034anuc.yaml @@ -1,23 +1,22 @@ # SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) %YAML 1.2 --- -$id: http://devicetree.org/schemas/iio/light/rohm,bu27034.yaml# +$id: http://devicetree.org/schemas/iio/light/rohm,bu27034anuc.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: ROHM BU27034 ambient light sensor +title: ROHM BU27034ANUC ambient light sensor maintainers: - Matti Vaittinen <mazziesaccount@gmail.com> description: | - ROHM BU27034 is an ambient light sesnor with 3 channels and 3 photo diodes + ROHM BU27034ANUC is an ambient light sensor with 2 channels and 2 photo diodes capable of detecting a very wide range of illuminance. Typical application is adjusting LCD and backlight power of TVs and mobile phones. - https://fscdn.rohm.com/en/products/databook/datasheet/ic/sensor/light/bu27034nuc-e.pdf properties: compatible: - const: rohm,bu27034 + const: rohm,bu27034anuc reg: maxItems: 1 @@ -37,7 +36,7 @@ examples: #size-cells = <0>; light-sensor@38 { - compatible = "rohm,bu27034"; + compatible = "rohm,bu27034anuc"; reg = <0x38>; vdd-supply = <&vdd>; }; diff --git a/Documentation/devicetree/bindings/iio/light/stk33xx.yaml b/Documentation/devicetree/bindings/iio/light/stk33xx.yaml index f6e22dc9814a..e4341fdced98 100644 --- a/Documentation/devicetree/bindings/iio/light/stk33xx.yaml +++ b/Documentation/devicetree/bindings/iio/light/stk33xx.yaml @@ -18,10 +18,15 @@ allOf: properties: compatible: - enum: - - sensortek,stk3310 - - sensortek,stk3311 - - sensortek,stk3335 + oneOf: + - enum: + - sensortek,stk3310 + - sensortek,stk3311 + - sensortek,stk3335 + - items: + - enum: + - sensortek,stk3013 + - const: sensortek,stk3310 reg: maxItems: 1 diff --git a/Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml b/Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml index 9790f75fc669..e8ca9a234027 100644 --- a/Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml +++ b/Documentation/devicetree/bindings/iio/magnetometer/asahi-kasei,ak8975.yaml @@ -18,12 +18,15 @@ properties: - asahi-kasei,ak09911 - asahi-kasei,ak09912 - asahi-kasei,ak09916 + - items: + # ak09918 is register compatible with ak09912. + - const: asahi-kasei,ak09918 + - const: asahi-kasei,ak09912 - enum: - ak8975 - ak8963 - ak09911 - ak09912 - - ak09916 deprecated: true reg: diff --git a/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml b/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml index 2867ab6bf9b0..a3838ab0c524 100644 --- a/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml +++ b/Documentation/devicetree/bindings/iio/magnetometer/bosch,bmc150_magn.yaml @@ -36,6 +36,9 @@ properties: interrupts: maxItems: 1 + mount-matrix: + description: an optional 3x3 mounting rotation matrix. + additionalProperties: false required: diff --git a/Documentation/devicetree/bindings/iio/pressure/sensirion,sdp500.yaml b/Documentation/devicetree/bindings/iio/pressure/sensirion,sdp500.yaml new file mode 100644 index 000000000000..813239f6879a --- /dev/null +++ b/Documentation/devicetree/bindings/iio/pressure/sensirion,sdp500.yaml @@ -0,0 +1,46 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/pressure/sensirion,sdp500.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: sdp500/sdp510 pressure sensor with I2C bus interface + +maintainers: + - Petar Stoykov <petar.stoykov@prodrive-technologies.com> + +description: | + Pressure sensor from Sensirion with I2C bus interface. + There is no software difference between sdp500 and sdp510. + +properties: + compatible: + oneOf: + - items: + - const: sensirion,sdp510 + - const: sensirion,sdp500 + - const: sensirion,sdp500 + + reg: + maxItems: 1 + + vdd-supply: true + +required: + - compatible + - reg + - vdd-supply + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + pressure@40 { + compatible = "sensirion,sdp500"; + reg = <0x40>; + vdd-supply = <&foo>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/proximity/awinic,aw96103.yaml b/Documentation/devicetree/bindings/iio/proximity/awinic,aw96103.yaml new file mode 100644 index 000000000000..7a83ceced11c --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/awinic,aw96103.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/proximity/awinic,aw96103.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Awinic's AW96103 capacitive proximity sensor and similar + +maintainers: + - Wang Shuaijie <wangshuaijie@awinic.com> + +description: | + Awinic's AW96103/AW96105 proximity sensor. + The specific absorption rate (SAR) is a metric that measures + the degree of absorption of electromagnetic radiation emitted by + wireless devices, such as mobile phones and tablets, by human tissue. + In mobile phone applications, the proximity sensor is primarily + used to detect the proximity of the human body to the phone. When the + phone approaches the human body, it will actively reduce the transmit + power of the antenna to keep the SAR within a safe range. Therefore, + we also refer to the proximity sensor as a SAR sensor. + +properties: + compatible: + enum: + - awinic,aw96103 + - awinic,aw96105 + + reg: + maxItems: 1 + + interrupts: + description: + Generated by the device to announce that a close/far + proximity event has happened. + maxItems: 1 + + vcc-supply: true + +required: + - compatible + - reg + - interrupts + - vcc-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + proximity@12 { + compatible = "awinic,aw96103"; + reg = <0x12>; + interrupt-parent = <&gpio>; + interrupts = <23 IRQ_TYPE_EDGE_FALLING>; + vcc-supply = <&pp1800_prox>; + }; + }; diff --git a/Documentation/devicetree/bindings/iio/proximity/tyhx,hx9023s.yaml b/Documentation/devicetree/bindings/iio/proximity/tyhx,hx9023s.yaml new file mode 100644 index 000000000000..64ce8bc8bd36 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/proximity/tyhx,hx9023s.yaml @@ -0,0 +1,93 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/proximity/tyhx,hx9023s.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TYHX HX9023S capacitive proximity sensor + +maintainers: + - Yasin Lee <yasin.lee.x@gmail.com> + +description: | + TYHX HX9023S proximity sensor. Datasheet can be found here: + http://www.tianyihexin.com/ueditor/php/upload/file/20240614/1718336303992081.pdf + +properties: + compatible: + const: tyhx,hx9023s + + reg: + maxItems: 1 + + interrupts: + description: + Generated by device to announce preceding read request has finished + and data is available or that a close/far proximity event has happened. + maxItems: 1 + + vdd-supply: true + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^channel@[0-4]$": + $ref: /schemas/iio/adc/adc.yaml + type: object + unevaluatedProperties: false + + properties: + reg: + minimum: 0 + maximum: 4 + description: The channel number. + +required: + - compatible + - reg + - vdd-supply + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + proximity@2a { + compatible = "tyhx,hx9023s"; + reg = <0x2a>; + interrupt-parent = <&pio>; + interrupts = <16 IRQ_TYPE_EDGE_FALLING>; + vdd-supply = <&pp1800_prox>; + + #address-cells = <1>; + #size-cells = <0>; + + channel@0 { + reg = <0>; + single-channel = <0>; + }; + channel@1 { + reg = <1>; + single-channel = <1>; + }; + channel@2 { + reg = <2>; + single-channel = <2>; + }; + channel@3 { + reg = <3>; + diff-channels = <1 0>; + }; + channel@4 { + reg = <4>; + diff-channels = <2 0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/interconnect/qcom,msm8939.yaml b/Documentation/devicetree/bindings/interconnect/qcom,msm8939.yaml index fd15ab5014fb..4b08be72bbd7 100644 --- a/Documentation/devicetree/bindings/interconnect/qcom,msm8939.yaml +++ b/Documentation/devicetree/bindings/interconnect/qcom,msm8939.yaml @@ -4,14 +4,14 @@ $id: http://devicetree.org/schemas/interconnect/qcom,msm8939.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: Qualcomm MSM8939 Network-On-Chip interconnect +title: Qualcomm MSM8937/MSM8939/MSM8976 Network-On-Chip interconnect maintainers: - Konrad Dybcio <konradybcio@kernel.org> -description: | - The Qualcomm MSM8939 interconnect providers support adjusting the - bandwidth requirements between the various NoC fabrics. +description: + The Qualcomm MSM8937/MSM8939/MSM8976 interconnect providers support + adjusting the bandwidth requirements between the various NoC fabrics. allOf: - $ref: qcom,rpm-common.yaml# @@ -19,9 +19,15 @@ allOf: properties: compatible: enum: + - qcom,msm8937-bimc + - qcom,msm8937-pcnoc + - qcom,msm8937-snoc - qcom,msm8939-bimc - qcom,msm8939-pcnoc - qcom,msm8939-snoc + - qcom,msm8976-bimc + - qcom,msm8976-pcnoc + - qcom,msm8976-snoc reg: maxItems: 1 @@ -39,7 +45,10 @@ patternProperties: properties: compatible: - const: qcom,msm8939-snoc-mm + enum: + - qcom,msm8937-snoc-mm + - qcom,msm8939-snoc-mm + - qcom,msm8976-snoc-mm required: - compatible @@ -60,12 +69,6 @@ examples: compatible = "qcom,msm8939-snoc"; reg = <0x00580000 0x14000>; #interconnect-cells = <1>; - }; - - bimc: interconnect@400000 { - compatible = "qcom,msm8939-bimc"; - reg = <0x00400000 0x62000>; - #interconnect-cells = <1>; snoc_mm: interconnect-snoc { compatible = "qcom,msm8939-snoc-mm"; diff --git a/Documentation/devicetree/bindings/interconnect/qcom,msm8953.yaml b/Documentation/devicetree/bindings/interconnect/qcom,msm8953.yaml index 732e9fa001a4..343ff62d7b65 100644 --- a/Documentation/devicetree/bindings/interconnect/qcom,msm8953.yaml +++ b/Documentation/devicetree/bindings/interconnect/qcom,msm8953.yaml @@ -13,8 +13,7 @@ description: | The Qualcomm MSM8953 interconnect providers support adjusting the bandwidth requirements between the various NoC fabrics. - See also: - - dt-bindings/interconnect/qcom,msm8953.h + See also: include/dt-bindings/interconnect/qcom,msm8953.h properties: compatible: diff --git a/Documentation/devicetree/bindings/interconnect/qcom,msm8998-bwmon.yaml b/Documentation/devicetree/bindings/interconnect/qcom,msm8998-bwmon.yaml index 2cd1f5590fd9..189f5900ee50 100644 --- a/Documentation/devicetree/bindings/interconnect/qcom,msm8998-bwmon.yaml +++ b/Documentation/devicetree/bindings/interconnect/qcom,msm8998-bwmon.yaml @@ -26,6 +26,7 @@ properties: - items: - enum: - qcom,qcm2290-cpu-bwmon + - qcom,sa8775p-cpu-bwmon - qcom,sc7180-cpu-bwmon - qcom,sc7280-cpu-bwmon - qcom,sc8280xp-cpu-bwmon @@ -39,6 +40,7 @@ properties: - const: qcom,sdm845-bwmon # BWMON v4, unified register space - items: - enum: + - qcom,sa8775p-llcc-bwmon - qcom,sc7180-llcc-bwmon - qcom,sc8280xp-llcc-bwmon - qcom,sm6350-cpu-bwmon diff --git a/Documentation/devicetree/bindings/interconnect/qcom,rpmh.yaml b/Documentation/devicetree/bindings/interconnect/qcom,rpmh.yaml index 9318b845ec35..1b9164dc162f 100644 --- a/Documentation/devicetree/bindings/interconnect/qcom,rpmh.yaml +++ b/Documentation/devicetree/bindings/interconnect/qcom,rpmh.yaml @@ -71,7 +71,7 @@ properties: - qcom,sdx65-system-noc - qcom,sm8150-aggre1-noc - qcom,sm8150-aggre2-noc - - qcom,sm8150-camnoc-noc + - qcom,sm8150-camnoc-virt - qcom,sm8150-compute-noc - qcom,sm8150-config-noc - qcom,sm8150-dc-noc @@ -113,6 +113,9 @@ allOf: properties: compatible: enum: + - qcom,sc8180x-camnoc-virt + - qcom,sc8180x-mc-virt + - qcom,sc8180x-qup-virt - qcom,sdx65-mc-virt - qcom,sm8250-qup-virt then: diff --git a/Documentation/devicetree/bindings/misc/qcom,fastrpc.yaml b/Documentation/devicetree/bindings/misc/qcom,fastrpc.yaml index c27a8f33d8d7..0840a3d92513 100644 --- a/Documentation/devicetree/bindings/misc/qcom,fastrpc.yaml +++ b/Documentation/devicetree/bindings/misc/qcom,fastrpc.yaml @@ -26,6 +26,7 @@ properties: - mdsp - sdsp - cdsp + - cdsp1 memory-region: maxItems: 1 @@ -81,7 +82,7 @@ patternProperties: iommus: minItems: 1 - maxItems: 3 + maxItems: 10 qcom,nsessions: $ref: /schemas/types.yaml#/definitions/uint32 diff --git a/Documentation/devicetree/bindings/net/ti,cc1352p7.yaml b/Documentation/devicetree/bindings/net/ti,cc1352p7.yaml index 3dde10de4630..4f4253441547 100644 --- a/Documentation/devicetree/bindings/net/ti,cc1352p7.yaml +++ b/Documentation/devicetree/bindings/net/ti,cc1352p7.yaml @@ -29,6 +29,12 @@ properties: reset-gpios: maxItems: 1 + bootloader-backdoor-gpios: + maxItems: 1 + description: | + gpios to enable bootloader backdoor in cc1352p7 bootloader to allow + flashing new firmware. + vdds-supply: true required: @@ -46,6 +52,7 @@ examples: clocks = <&sclk_hf 0>, <&sclk_lf 25>; clock-names = "sclk_hf", "sclk_lf"; reset-gpios = <&pio 35 GPIO_ACTIVE_LOW>; + bootloader-backdoor-gpios = <&pio 36 GPIO_ACTIVE_LOW>; vdds-supply = <&vdds>; }; }; diff --git a/Documentation/devicetree/bindings/nvmem/fsl,layerscape-sfp.yaml b/Documentation/devicetree/bindings/nvmem/fsl,layerscape-sfp.yaml index 70fb2ad25103..1b20b49eee79 100644 --- a/Documentation/devicetree/bindings/nvmem/fsl,layerscape-sfp.yaml +++ b/Documentation/devicetree/bindings/nvmem/fsl,layerscape-sfp.yaml @@ -15,6 +15,7 @@ description: | allOf: - $ref: nvmem.yaml# + - $ref: nvmem-deprecated-cells.yaml properties: compatible: diff --git a/Documentation/devicetree/bindings/nvmem/imx-ocotp.yaml b/Documentation/devicetree/bindings/nvmem/imx-ocotp.yaml index e21c06e9a741..b2cb76cf9053 100644 --- a/Documentation/devicetree/bindings/nvmem/imx-ocotp.yaml +++ b/Documentation/devicetree/bindings/nvmem/imx-ocotp.yaml @@ -14,7 +14,7 @@ maintainers: description: | This binding represents the on-chip eFuse OTP controller found on i.MX6Q/D, i.MX6DL/S, i.MX6SL, i.MX6SX, i.MX6UL, i.MX6ULL/ULZ, i.MX6SLL, - i.MX7D/S, i.MX7ULP, i.MX8MQ, i.MX8MM, i.MX8MN i.MX8MP and i.MX93 SoCs. + i.MX7D/S, i.MX7ULP, i.MX8MQ, i.MX8MM, i.MX8MN i.MX8MP and i.MX93/5 SoCs. allOf: - $ref: nvmem.yaml# @@ -36,6 +36,7 @@ properties: - fsl,imx8mq-ocotp - fsl,imx8mm-ocotp - fsl,imx93-ocotp + - fsl,imx95-ocotp - const: syscon - items: - enum: diff --git a/Documentation/devicetree/bindings/nvmem/layouts/nvmem-layout.yaml b/Documentation/devicetree/bindings/nvmem/layouts/nvmem-layout.yaml index 3b40f7880774..382507060651 100644 --- a/Documentation/devicetree/bindings/nvmem/layouts/nvmem-layout.yaml +++ b/Documentation/devicetree/bindings/nvmem/layouts/nvmem-layout.yaml @@ -21,6 +21,7 @@ oneOf: - $ref: fixed-layout.yaml - $ref: kontron,sl28-vpd.yaml - $ref: onie,tlv-layout.yaml + - $ref: u-boot,env.yaml properties: compatible: true diff --git a/Documentation/devicetree/bindings/nvmem/u-boot,env.yaml b/Documentation/devicetree/bindings/nvmem/layouts/u-boot,env.yaml index 9c36afc7084b..56a8f55d4a09 100644 --- a/Documentation/devicetree/bindings/nvmem/u-boot,env.yaml +++ b/Documentation/devicetree/bindings/nvmem/layouts/u-boot,env.yaml @@ -1,10 +1,10 @@ # SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause %YAML 1.2 --- -$id: http://devicetree.org/schemas/nvmem/u-boot,env.yaml# +$id: http://devicetree.org/schemas/nvmem/layouts/u-boot,env.yaml# $schema: http://devicetree.org/meta-schemas/core.yaml# -title: U-Boot environment variables +title: U-Boot environment variables layout description: | U-Boot uses environment variables to store device parameters and @@ -21,9 +21,6 @@ description: | This binding allows marking storage device (as containing env data) and specifying used format. - Right now only flash partition case is covered but it may be extended to e.g. - UBI volumes in the future. - Variables can be defined as NVMEM device subnodes. maintainers: @@ -42,6 +39,7 @@ properties: const: brcm,env reg: + description: Partition offset and size for env on top of MTD maxItems: 1 bootcmd: @@ -58,6 +56,17 @@ properties: description: The first argument is a MAC address offset. const: 1 +allOf: + - if: + properties: + $nodename: + not: + contains: + pattern: "^partition@[0-9a-f]+$" + then: + properties: + reg: false + additionalProperties: false examples: @@ -101,3 +110,23 @@ examples: }; }; }; + - | + partition@0 { + reg = <0x0 0x100000>; + label = "ubi"; + compatible = "linux,ubi"; + + volumes { + ubi-volume-u-boot-env { + volname = "env"; + + nvmem-layout { + compatible = "u-boot,env"; + + ethaddr { + #nvmem-cell-cells = <1>; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/nvmem/st,stm32-romem.yaml b/Documentation/devicetree/bindings/nvmem/st,stm32-romem.yaml index 92bfe25f0571..3b2aa605a551 100644 --- a/Documentation/devicetree/bindings/nvmem/st,stm32-romem.yaml +++ b/Documentation/devicetree/bindings/nvmem/st,stm32-romem.yaml @@ -17,6 +17,7 @@ maintainers: allOf: - $ref: nvmem.yaml# + - $ref: nvmem-deprecated-cells.yaml# properties: compatible: @@ -32,6 +33,8 @@ properties: patternProperties: "^.*@[0-9a-f]+$": type: object + $ref: layouts/fixed-cell.yaml + unevaluatedProperties: false properties: st,non-secure-otp: diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml index adb15f4c8f6c..b320a39de7fe 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml @@ -1541,6 +1541,8 @@ patternProperties: description: Turing Machines, Inc. "^tyan,.*": description: Tyan Computer Corporation + "^tyhx,.*": + description: NanjingTianyihexin Electronics Ltd. "^u-blox,.*": description: u-blox "^u-boot,.*": diff --git a/Documentation/iio/ad4000.rst b/Documentation/iio/ad4000.rst new file mode 100644 index 000000000000..de8fd3ae6e62 --- /dev/null +++ b/Documentation/iio/ad4000.rst @@ -0,0 +1,131 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +============= +AD4000 driver +============= + +Device driver for Analog Devices Inc. AD4000 series of ADCs. + +Supported devices +================= + +* `AD4000 <https://www.analog.com/AD4000>`_ +* `AD4001 <https://www.analog.com/AD4001>`_ +* `AD4002 <https://www.analog.com/AD4002>`_ +* `AD4003 <https://www.analog.com/AD4003>`_ +* `AD4004 <https://www.analog.com/AD4004>`_ +* `AD4005 <https://www.analog.com/AD4005>`_ +* `AD4006 <https://www.analog.com/AD4006>`_ +* `AD4007 <https://www.analog.com/AD4007>`_ +* `AD4008 <https://www.analog.com/AD4008>`_ +* `AD4010 <https://www.analog.com/AD4010>`_ +* `AD4011 <https://www.analog.com/AD4011>`_ +* `AD4020 <https://www.analog.com/AD4020>`_ +* `AD4021 <https://www.analog.com/AD4021>`_ +* `AD4022 <https://www.analog.com/AD4022>`_ +* `ADAQ4001 <https://www.analog.com/ADAQ4001>`_ +* `ADAQ4003 <https://www.analog.com/ADAQ4003>`_ + +Wiring connections +------------------ + +Devices of the AD4000 series can be connected to the SPI host controller in a +few different modes. + +CS mode, 3-wire turbo mode +^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Datasheet "3-wire" mode is what most resembles standard SPI connection which, +for these devices, comprises of connecting the controller CS line to device CNV +pin and other SPI lines as usual. This configuration is (misleadingly) called +"CS Mode, 3-Wire Turbo Mode" connection in datasheets. +NOTE: The datasheet definition of 3-wire mode for the AD4000 series is NOT the +same of standard spi-3wire mode. +This is the only connection mode that allows configuration register access but +it requires the SPI controller to support the ``SPI_MOSI_IDLE_HIGH`` feature. + +Omit the ``adi,sdi-pin`` property in device tree to select this mode. + +:: + + +-------------+ + + ----------------------------------| SDO | + | | | + | +-------------------| CS | + | v | | + | +--------------------+ | HOST | + | | CNV | | | + +--->| SDI AD4000 SDO |-------->| SDI | + | SCK | | | + +--------------------+ | | + ^ | | + +--------------------| SCLK | + +-------------+ + +CS mode, 3-wire, without busy indicator +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Another wiring configuration supported as "3-wire" mode has the SDI pin +hard-wired to digital input/output interface supply (VIO). In this setup, the +controller is not required to support ``SPI_MOSI_IDLE_HIGH`` but register access +is not possible. This connection mode saves one wire and works with any SPI +controller. + +Set the ``adi,sdi-pin`` device tree property to ``"high"`` to select this mode. + +:: + + +-------------+ + +--------------------| CS | + v | | + VIO +--------------------+ | HOST | + | | CNV | | | + +--->| SDI AD4000 SDO |-------->| SDI | + | SCK | | | + +--------------------+ | | + ^ | | + +--------------------| SCLK | + +-------------+ + +Alternatively, a GPIO may be connected to the device CNV pin. This is similar to +the previous wiring configuration but saves the use of a CS line. + +:: + + +-------------+ + +--------------------| GPIO | + v | | + VIO +--------------------+ | HOST | + | | CNV | | | + +--->| SDI AD4000 SDO |-------->| SDI | + | SCK | | | + +--------------------+ | | + ^ | | + +--------------------| SCLK | + +-------------+ + +CS mode, 4-wire without busy indicator +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +In datasheet "4-wire" mode, the controller CS line is connected to the ADC SDI +pin and a GPIO is connected to the ADC CNV pin. This connection mode may better +suit scenarios where multiple ADCs can share one CNV trigger. + +Set ``adi,sdi-pin`` to ``"cs"`` to select this mode. + + +:: + + +-------------+ + + ----------------------------------| CS | + | | | + | +-------------------| GPIO | + | v | | + | +--------------------+ | HOST | + | | CNV | | | + +--->| SDI AD4000 SDO |-------->| SDI | + | SCK | | | + +--------------------+ | | + ^ | | + +--------------------| SCLK | + +-------------+ diff --git a/Documentation/iio/ad4695.rst b/Documentation/iio/ad4695.rst new file mode 100644 index 000000000000..33ed29b7c98a --- /dev/null +++ b/Documentation/iio/ad4695.rst @@ -0,0 +1,167 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +============= +AD4695 driver +============= + +ADC driver for Analog Devices Inc. AD4695 and similar devices. The module name +is ``ad4695``. + + +Supported devices +================= + +The following chips are supported by this driver: + +* `AD4695 <https://www.analog.com/AD4695>`_ +* `AD4696 <https://www.analog.com/AD4696>`_ +* `AD4697 <https://www.analog.com/AD4697>`_ +* `AD4698 <https://www.analog.com/AD4698>`_ + + +Supported features +================== + +SPI wiring modes +---------------- + +The driver currently supports the following SPI wiring configuration: + +4-wire mode +^^^^^^^^^^^ + +In this mode, CNV and CS are tied together and there is a single SDO line. + +.. code-block:: + + +-------------+ +-------------+ + | CS |<-+------| CS | + | CNV |<-+ | | + | ADC | | HOST | + | | | | + | SDI |<--------| SDO | + | SDO |-------->| SDI | + | SCLK |<--------| SCLK | + +-------------+ +-------------+ + +To use this mode, in the device tree, omit the ``cnv-gpios`` and +``spi-rx-bus-width`` properties. + +Channel configuration +--------------------- + +Since the chip supports multiple ways to configure each channel, this must be +described in the device tree based on what is actually wired up to the inputs. + +There are three typical configurations: + +An ``INx`` pin is used as the positive input with the ``REFGND``, ``COM`` or +the next ``INx`` pin as the negative input. + +Pairing with REFGND +^^^^^^^^^^^^^^^^^^^ + +Each ``INx`` pin can be used as a pseudo-differential input in conjunction with +the ``REFGND`` pin. The device tree will look like this: + +.. code-block:: + + channel@0 { + reg = <0>; /* IN0 */ + }; + +If no other channel properties are needed (e.g. ``adi,no-high-z``), the channel +node can be omitted entirely. + +This will appear on the IIO bus as the ``voltage0`` channel. The processed value +(*raw × scale*) will be the voltage present on the ``IN0`` pin relative to +``REFGND``. (Offset is always 0 when pairing with ``REFGND``.) + +Pairing with COM +^^^^^^^^^^^^^^^^ + +Each ``INx`` pin can be used as a pseudo-differential input in conjunction with +the ``COM`` pin. The device tree will look like this: + +.. code-block:: + + com-supply = <&vref_div_2>; + + channel@1 { + reg = <1>; /* IN1 */ + common-mode-channel = <AD4695_COMMON_MODE_COM>; + bipolar; + }; + +This will appear on the IIO bus as the ``voltage1`` channel. The processed value +(*(raw + offset) × scale*) will be the voltage measured on the ``IN1`` pin +relative to ``REFGND``. (The offset is determined by the ``com-supply`` voltage.) + +The macro comes from: + +.. code-block:: + + #include <dt-bindings/iio/adi,ad4695.h> + +Pairing two INx pins +^^^^^^^^^^^^^^^^^^^^ + +An even-numbered ``INx`` pin and the following odd-numbered ``INx`` pin can be +used as a pseudo-differential input. The device tree for using ``IN2`` as the +positive input and ``IN3`` as the negative input will look like this: + +.. code-block:: + + in3-supply = <&vref_div_2>; + + channel@2 { + reg = <2>; /* IN2 */ + common-mode-channel = <3>; /* IN3 */ + bipolar; + }; + +This will appear on the IIO bus as the ``voltage2`` channel. The processed value +(*(raw + offset) × scale*) will be the voltage measured on the ``IN1`` pin +relative to ``REFGND``. (Offset is determined by the ``in3-supply`` voltage.) + +VCC supply +---------- + +The chip supports being powered by an external LDO via the ``VCC`` input or an +internal LDO via the ``LDO_IN`` input. The driver looks at the device tree to +determine which is being used. If ``ldo-supply`` is present, then the internal +LDO is used. If ``vcc-supply`` is present, then the external LDO is used and +the internal LDO is disabled. + +Reference voltage +----------------- + +The chip supports an external reference voltage via the ``REF`` input or an +internal buffered reference voltage via the ``REFIN`` input. The driver looks +at the device tree to determine which is being used. If ``ref-supply`` is +present, then the external reference voltage is used and the internal buffer is +disabled. If ``refin-supply`` is present, then the internal buffered reference +voltage is used. + +Gain/offset calibration +----------------------- + +System calibration is supported using the channel gain and offset registers via +the ``calibscale`` and ``calibbias`` attributes respectively. + +Unimplemented features +---------------------- + +- Additional wiring modes +- Threshold events +- Oversampling +- GPIO support +- CRC support + +Device buffers +============== + +This driver supports hardware triggered buffers. This uses the "advanced +sequencer" feature of the chip to trigger a burst of conversions. + +Also see :doc:`iio_devbuf` for more general information. diff --git a/Documentation/iio/ad7380.rst b/Documentation/iio/ad7380.rst new file mode 100644 index 000000000000..9c784c1e652e --- /dev/null +++ b/Documentation/iio/ad7380.rst @@ -0,0 +1,130 @@ +.. SPDX-License-Identifier: GPL-2.0-only + +============= +AD7380 driver +============= + +ADC driver for Analog Devices Inc. AD7380 and similar devices. The module name +is ``ad7380``. + + +Supported devices +================= + +The following chips are supported by this driver: + +* `AD7380 <https://www.analog.com/en/products/ad7380.html>`_ +* `AD7381 <https://www.analog.com/en/products/ad7381.html>`_ +* `AD7383 <https://www.analog.com/en/products/ad7383.html>`_ +* `AD7384 <https://www.analog.com/en/products/ad7384.html>`_ +* `AD7386 <https://www.analog.com/en/products/ad7386.html>`_ +* `AD7387 <https://www.analog.com/en/products/ad7387.html>`_ +* `AD7388 <https://www.analog.com/en/products/ad7388.html>`_ +* `AD7380-4 <https://www.analog.com/en/products/ad7380-4.html>`_ +* `AD7381-4 <https://www.analog.com/en/products/ad7381-4.html>`_ +* `AD7383-4 <https://www.analog.com/en/products/ad7383-4.html>`_ +* `AD7384-4 <https://www.analog.com/en/products/ad7384-4.html>`_ +* `AD7386-4 <https://www.analog.com/en/products/ad7386-4.html>`_ +* `AD7387-4 <https://www.analog.com/en/products/ad7387-4.html>`_ +* `AD7388-4 <https://www.analog.com/en/products/ad7388-4.html>`_ + + +Supported features +================== + +SPI wiring modes +---------------- + +ad738x ADCs can output data on several SDO lines (1/2/4). The driver currently +supports only 1 SDO line. + +Reference voltage +----------------- + +2 possible reference voltage sources are supported: + +- Internal reference (2.5V) +- External reference (2.5V to 3.3V) + +The source is determined by the device tree. If ``refio-supply`` is present, +then the external reference is used, else the internal reference is used. + +Oversampling and resolution boost +--------------------------------- + +This family supports 2 types of oversampling: normal average and rolling +average. Only normal average is supported by the driver, as rolling average can +be achieved by processing a captured data buffer. The following ratios are +available: 1 (oversampling disabled)/2/4/8/16/32. + +When the on-chip oversampling function is enabled the performance of the ADC can +exceed the default resolution. To accommodate the performance boost achievable, +it is possible to enable an additional two bits of resolution. Because the +resolution boost feature can only be enabled when oversampling is enabled and +oversampling is not as useful without the resolution boost, the driver +automatically enables the resolution boost if and only if oversampling is +enabled. + +Since the resolution boost feature causes 16-bit chips to now have 18-bit data +which means the storagebits has to change from 16 to 32 bits, we use the new +ext_scan_type feature to allow changing the scan_type at runtime. Unfortunately +libiio does not support it. So when enabling or disabling oversampling, user +must restart iiod using the following command: + +.. code-block:: bash + + root:~# systemctl restart iiod + +Channel selection and sequencer (single-end chips only) +------------------------------------------------------- + +Single-ended chips of this family (ad7386/7/8(-4)) have a 2:1 multiplexer in +front of each ADC. They also include additional configuration registers that +allow for either manual selection or automatic switching (sequencer mode), of +the multiplexer inputs. + +From an IIO point of view, all inputs are exported, i.e ad7386/7/8 +export 4 channels and ad7386-4/7-4/8-4 export 8 channels. + +Inputs ``AinX0`` of multiplexers correspond to the first half of IIO channels (i.e +0-1 or 0-3) and inputs ``AinX1`` correspond to second half (i.e 2-3 or 4-7). +Example for AD7386/7/8 (2 channels parts): + +.. code-block:: + + IIO | AD7386/7/8 + | +---------------------------- + | | _____ ______ + | | | | | | + voltage0 | AinA0 --|--->| | | | + | | | mux |----->| ADCA |--- + voltage2 | AinA1 --|--->| | | | + | | |_____| |_____ | + | | _____ ______ + | | | | | | + voltage1 | AinB0 --|--->| | | | + | | | mux |----->| ADCB |--- + voltage3 | AinB1 --|--->| | | | + | | |_____| |______| + | | + | +---------------------------- + + +When enabling sequencer mode, the effective sampling rate is divided by two. + +Unimplemented features +---------------------- + +- 2/4 SDO lines +- Rolling average oversampling +- Power down mode +- CRC indication +- Alert + + +Device buffers +============== + +This driver supports IIO triggered buffers. + +See :doc:`iio_devbuf` for more information. diff --git a/Documentation/iio/adxl380.rst b/Documentation/iio/adxl380.rst new file mode 100644 index 000000000000..376dee5fe1dd --- /dev/null +++ b/Documentation/iio/adxl380.rst @@ -0,0 +1,233 @@ +.. SPDX-License-Identifier: GPL-2.0 + +=============== +ADXL380 driver +=============== + +This driver supports Analog Device's ADXL380/382 on SPI/I2C bus. + +1. Supported devices +==================== + +* `ADXL380 <https://www.analog.com/ADXL380>`_ +* `ADXL382 <https://www.analog.com/ADXL382>`_ + +The ADXL380/ADXL382 is a low noise density, low power, 3-axis accelerometer with +selectable measurement ranges. The ADXL380 supports the ±4 g, ±8 g, and ±16 g +ranges, and the ADXL382 supports ±15 g, ±30 g, and ±60 g ranges. + +2. Device attributes +==================== + +Accelerometer measurements are always provided. + +Temperature data are also provided. This data can be used to monitor the +internal system temperature or to improve the temperature stability of the +device via calibration. + +Each IIO device, has a device folder under ``/sys/bus/iio/devices/iio:deviceX``, +where X is the IIO index of the device. Under these folders reside a set of +device files, depending on the characteristics and features of the hardware +device in questions. These files are consistently generalized and documented in +the IIO ABI documentation. + +The following tables show the adxl380 related device files, found in the +specific device folder path ``/sys/bus/iio/devices/iio:deviceX``. + ++---------------------------------------------------+----------------------------------------------------------+ +| 3-Axis Accelerometer related device files | Description | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_scale | Scale for the accelerometer channels. | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_filter_high_pass_3db_frequency | Low pass filter bandwidth. | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_filter_high_pass_3db_frequency_available | Available low pass filter bandwidth configurations. | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_filter_low_pass_3db_frequency | High pass filter bandwidth. | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_filter_low_pass_3db_frequency_available | Available high pass filter bandwidth configurations. | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_x_calibbias | Calibration offset for the X-axis accelerometer channel. | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_x_raw | Raw X-axis accelerometer channel value. | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_y_calibbias | y-axis acceleration offset correction | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_y_raw | Raw Y-axis accelerometer channel value. | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_z_calibbias | Calibration offset for the Z-axis accelerometer channel. | ++---------------------------------------------------+----------------------------------------------------------+ +| in_accel_z_raw | Raw Z-axis accelerometer channel value. | ++---------------------------------------------------+----------------------------------------------------------+ + ++----------------------------------+--------------------------------------------+ +| Temperature sensor related files | Description | ++----------------------------------+--------------------------------------------+ +| in_temp_raw | Raw temperature channel value. | ++----------------------------------+--------------------------------------------+ +| in_temp_offset | Offset for the temperature sensor channel. | ++----------------------------------+--------------------------------------------+ +| in_temp_scale | Scale for the temperature sensor channel. | ++----------------------------------+--------------------------------------------+ + ++------------------------------+----------------------------------------------+ +| Miscellaneous device files | Description | ++------------------------------+----------------------------------------------+ +| name | Name of the IIO device. | ++------------------------------+----------------------------------------------+ +| sampling_frequency | Currently selected sample rate. | ++------------------------------+----------------------------------------------+ +| sampling_frequency_available | Available sampling frequency configurations. | ++------------------------------+----------------------------------------------+ + +Channels processed values +------------------------- + +A channel value can be read from its _raw attribute. The value returned is the +raw value as reported by the devices. To get the processed value of the channel, +apply the following formula: + +.. code-block:: bash + + processed value = (_raw + _offset) * _scale + +Where _offset and _scale are device attributes. If no _offset attribute is +present, simply assume its value is 0. + +The adis16475 driver offers data for 2 types of channels, the table below shows +the measurement units for the processed value, which are defined by the IIO +framework: + ++-------------------------------------+---------------------------+ +| Channel type | Measurement unit | ++-------------------------------------+---------------------------+ +| Acceleration on X, Y, and Z axis | Meters per Second squared | ++-------------------------------------+---------------------------+ +| Temperature | Millidegrees Celsius | ++-------------------------------------+---------------------------+ + +Usage examples +-------------- + +Show device name: + +.. code-block:: bash + + root:/sys/bus/iio/devices/iio:device0> cat name + adxl382 + +Show accelerometer channels value: + +.. code-block:: bash + + root:/sys/bus/iio/devices/iio:device0> cat in_accel_x_raw + -1771 + root:/sys/bus/iio/devices/iio:device0> cat in_accel_y_raw + 282 + root:/sys/bus/iio/devices/iio:device0> cat in_accel_z_raw + -1523 + root:/sys/bus/iio/devices/iio:device0> cat in_accel_scale + 0.004903325 + +- X-axis acceleration = in_accel_x_raw * in_accel_scale = −8.683788575 m/s^2 +- Y-axis acceleration = in_accel_y_raw * in_accel_scale = 1.38273765 m/s^2 +- Z-axis acceleration = in_accel_z_raw * in_accel_scale = -7.467763975 m/s^2 + +Set calibration offset for accelerometer channels: + +.. code-block:: bash + + root:/sys/bus/iio/devices/iio:device0> cat in_accel_x_calibbias + 0 + + root:/sys/bus/iio/devices/iio:device0> echo 50 > in_accel_x_calibbias + root:/sys/bus/iio/devices/iio:device0> cat in_accel_x_calibbias + 50 + +Set sampling frequency: + +.. code-block:: bash + + root:/sys/bus/iio/devices/iio:device0> cat sampling_frequency + 16000 + root:/sys/bus/iio/devices/iio:device0> cat sampling_frequency_available + 16000 32000 64000 + + root:/sys/bus/iio/devices/iio:device0> echo 32000 > sampling_frequency + root:/sys/bus/iio/devices/iio:device0> cat sampling_frequency + 32000 + +Set low pass filter bandwidth for accelerometer channels: + +.. code-block:: bash + + root:/sys/bus/iio/devices/iio:device0> cat in_accel_filter_low_pass_3db_frequency + 32000 + root:/sys/bus/iio/devices/iio:device0> cat in_accel_filter_low_pass_3db_frequency_available + 32000 8000 4000 2000 + + root:/sys/bus/iio/devices/iio:device0> echo 2000 > in_accel_filter_low_pass_3db_frequency + root:/sys/bus/iio/devices/iio:device0> cat in_accel_filter_low_pass_3db_frequency + 2000 + +3. Device buffers +================= + +This driver supports IIO buffers. + +All devices support retrieving the raw acceleration and temperature measurements +using buffers. + +Usage examples +-------------- + +Select channels for buffer read: + +.. code-block:: bash + + root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_accel_x_en + root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_accel_y_en + root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_accel_z_en + root:/sys/bus/iio/devices/iio:device0> echo 1 > scan_elements/in_temp_en + +Set the number of samples to be stored in the buffer: + +.. code-block:: bash + + root:/sys/bus/iio/devices/iio:device0> echo 10 > buffer/length + +Enable buffer readings: + +.. code-block:: bash + + root:/sys/bus/iio/devices/iio:device0> echo 1 > buffer/enable + +Obtain buffered data: + +.. code-block:: bash + + root:/sys/bus/iio/devices/iio:device0> hexdump -C /dev/iio\:device0 + ... + 002bc300 f7 e7 00 a8 fb c5 24 80 f7 e7 01 04 fb d6 24 80 |......$.......$.| + 002bc310 f7 f9 00 ab fb dc 24 80 f7 c3 00 b8 fb e2 24 80 |......$.......$.| + 002bc320 f7 fb 00 bb fb d1 24 80 f7 b1 00 5f fb d1 24 80 |......$...._..$.| + 002bc330 f7 c4 00 c6 fb a6 24 80 f7 a6 00 68 fb f1 24 80 |......$....h..$.| + 002bc340 f7 b8 00 a3 fb e7 24 80 f7 9a 00 b1 fb af 24 80 |......$.......$.| + 002bc350 f7 b1 00 67 fb ee 24 80 f7 96 00 be fb 92 24 80 |...g..$.......$.| + 002bc360 f7 ab 00 7a fc 1b 24 80 f7 b6 00 ae fb 76 24 80 |...z..$......v$.| + 002bc370 f7 ce 00 a3 fc 02 24 80 f7 c0 00 be fb 8b 24 80 |......$.......$.| + 002bc380 f7 c3 00 93 fb d0 24 80 f7 ce 00 d8 fb c8 24 80 |......$.......$.| + 002bc390 f7 bd 00 c0 fb 82 24 80 f8 00 00 e8 fb db 24 80 |......$.......$.| + 002bc3a0 f7 d8 00 d3 fb b4 24 80 f8 0b 00 e5 fb c3 24 80 |......$.......$.| + 002bc3b0 f7 eb 00 c8 fb 92 24 80 f7 e7 00 ea fb cb 24 80 |......$.......$.| + 002bc3c0 f7 fd 00 cb fb 94 24 80 f7 e3 00 f2 fb b8 24 80 |......$.......$.| + ... + +See ``Documentation/iio/iio_devbuf.rst`` for more information about how buffered +data is structured. + +4. IIO Interfacing Tools +======================== + +See ``Documentation/iio/iio_tools.rst`` for the description of the available IIO +interfacing tools. diff --git a/Documentation/iio/index.rst b/Documentation/iio/index.rst index 9cb4c50cb20d..dfcf9618568a 100644 --- a/Documentation/iio/index.rst +++ b/Documentation/iio/index.rst @@ -18,8 +18,12 @@ Industrial I/O Kernel Drivers .. toctree:: :maxdepth: 1 + ad4000 + ad4695 + ad7380 ad7944 adis16475 adis16480 + adxl380 bno055 ep93xx_adc |