summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts')
-rw-r--r--arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts141
1 files changed, 122 insertions, 19 deletions
diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
index 5ed6c1376901..89ff404a528c 100644
--- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
+++ b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
@@ -6,8 +6,19 @@
* warranty of any kind, whether express or implied.
*/
+/*
+ * TODO: add Orion USB device port init when kernel.org support is added.
+ * TODO: add flash write support: see below.
+ * TODO: add power-off support.
+ * TODO: add I2C EEPROM support.
+ */
+
/dts-v1/;
-/include/ "orion5x.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+#include "orion5x-mv88f5182.dtsi"
/ {
model = "LaCie Ethernet Disk mini V2";
@@ -19,49 +30,84 @@
chosen {
bootargs = "console=ttyS0,115200n8 earlyprintk";
+ linux,stdout-path = &uart0;
};
- ocp@f1000000 {
- serial@12000 {
- clock-frequency = <166666667>;
- status = "okay";
- };
-
- sata@80000 {
- status = "okay";
- nr-ports = <2>;
- };
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000>,
+ <MBUS_ID(0x09, 0x00) 0 0xf2200000 0x800>,
+ <MBUS_ID(0x01, 0x0f) 0 0xfff80000 0x80000>;
};
- gpio_keys {
+ gpio-keys {
compatible = "gpio-keys";
+ pinctrl-0 = <&pmx_power_button>;
+ pinctrl-names = "default";
#address-cells = <1>;
#size-cells = <0>;
button@1 {
label = "Power-on Switch";
- linux,code = <116>; /* KEY_POWER */
- gpios = <&gpio0 18 0>;
+ linux,code = <KEY_POWER>;
+ gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>;
};
};
- gpio_leds {
+ gpio-leds {
compatible = "gpio-leds";
+ pinctrl-0 = <&pmx_power_led>;
+ pinctrl-names = "default";
led@1 {
label = "power:blue";
- gpios = <&gpio0 16 1>;
+ gpios = <&gpio0 16 GPIO_ACTIVE_LOW>;
};
};
};
-&mdio {
+&devbus_bootcs {
status = "okay";
- ethphy: ethernet-phy {
- reg = <8>;
+ /* Read parameters */
+ devbus,bus-width = <8>;
+ devbus,turn-off-ps = <90000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <186000>;
+ devbus,acc-next-ps = <186000>;
+
+ /* Write parameters */
+ devbus,wr-high-ps = <90000>;
+ devbus,wr-low-ps = <90000>;
+ devbus,ale-wr-ps = <90000>;
+
+ /*
+ * Currently the MTD code does not recognize the MX29LV400CBCT
+ * as a bottom-type device. This could cause risks of
+ * accidentally erasing critical flash sectors. We thus define
+ * a single, write-protected partition covering the whole
+ * flash. TODO: once the flash part TOP/BOTTOM detection
+ * issue is sorted out in the MTD code, break this into at
+ * least three partitions: 'u-boot code', 'u-boot environment'
+ * and 'whatever is left'.
+ */
+ flash@0 {
+ compatible = "cfi-flash";
+ reg = <0 0x80000>;
+ bank-width = <1>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "Full512Kb";
+ reg = <0 0x80000>;
+ read-only;
+ };
};
};
+&ehci0 {
+ status = "okay";
+};
+
&eth {
status = "okay";
@@ -69,3 +115,60 @@
phy-handle = <&ethphy>;
};
};
+
+&i2c {
+ status = "okay";
+ clock-frequency = <100000>;
+ #address-cells = <1>;
+
+ rtc@32 {
+ compatible = "ricoh,rs5c372a";
+ reg = <0x32>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+&mdio {
+ status = "okay";
+
+ ethphy: ethernet-phy {
+ reg = <8>;
+ };
+};
+
+&pinctrl {
+ pinctrl-0 = <&pmx_rtc &pmx_power_led_ctrl>;
+ pinctrl-names = "default";
+
+ pmx_power_button: pmx-power-button {
+ marvell,pins = "mpp18";
+ marvell,function = "gpio";
+ };
+
+ pmx_power_led: pmx-power-led {
+ marvell,pins = "mpp16";
+ marvell,function = "gpio";
+ };
+
+ pmx_power_led_ctrl: pmx-power-led-ctrl {
+ marvell,pins = "mpp17";
+ marvell,function = "gpio";
+ };
+
+ pmx_rtc: pmx-rtc {
+ marvell,pins = "mpp3";
+ marvell,function = "gpio";
+ };
+};
+
+&sata {
+ pinctrl-0 = <&pmx_sata0 &pmx_sata1>;
+ pinctrl-names = "default";
+ status = "okay";
+ nr-ports = <2>;
+};
+
+&uart0 {
+ status = "okay";
+};