diff options
Diffstat (limited to 'drivers/i2c/busses')
42 files changed, 2438 insertions, 1918 deletions
diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig index 48438cc5d0ca..6ee997b2817c 100644 --- a/drivers/i2c/busses/Kconfig +++ b/drivers/i2c/busses/Kconfig @@ -4,6 +4,9 @@ menu "I2C Hardware Bus support" +comment "PC SMBus host controller drivers" + depends on PCI + config I2C_ALI1535 tristate "ALI 1535" depends on PCI @@ -73,6 +76,186 @@ config I2C_AMD8111 This driver can also be built as a module. If so, the module will be called i2c-amd8111. +config I2C_I801 + tristate "Intel 82801 (ICH)" + depends on PCI + help + If you say yes to this option, support will be included for the Intel + 801 family of mainboard I2C interfaces. Specifically, the following + versions of the chipset are supported: + 82801AA + 82801AB + 82801BA + 82801CA/CAM + 82801DB + 82801EB/ER (ICH5/ICH5R) + 6300ESB + ICH6 + ICH7 + ESB2 + ICH8 + ICH9 + Tolapai + ICH10 + + This driver can also be built as a module. If so, the module + will be called i2c-i801. + +config I2C_ISCH + tristate "Intel SCH SMBus 1.0" + depends on PCI + help + Say Y here if you want to use SMBus controller on the Intel SCH + based systems. + + This driver can also be built as a module. If so, the module + will be called i2c-isch. + +config I2C_PIIX4 + tristate "Intel PIIX4 and compatible (ATI/Serverworks/Broadcom/SMSC)" + depends on PCI + help + If you say yes to this option, support will be included for the Intel + PIIX4 family of mainboard I2C interfaces. Specifically, the following + versions of the chipset are supported (note that Serverworks is part + of Broadcom): + Intel PIIX4 + Intel 440MX + ATI IXP200 + ATI IXP300 + ATI IXP400 + ATI SB600 + ATI SB700 + ATI SB800 + Serverworks OSB4 + Serverworks CSB5 + Serverworks CSB6 + Serverworks HT-1000 + SMSC Victory66 + + This driver can also be built as a module. If so, the module + will be called i2c-piix4. + +config I2C_NFORCE2 + tristate "Nvidia nForce2, nForce3 and nForce4" + depends on PCI + help + If you say yes to this option, support will be included for the Nvidia + nForce2, nForce3 and nForce4 families of mainboard I2C interfaces. + + This driver can also be built as a module. If so, the module + will be called i2c-nforce2. + +config I2C_NFORCE2_S4985 + tristate "SMBus multiplexing on the Tyan S4985" + depends on I2C_NFORCE2 && EXPERIMENTAL + help + Enabling this option will add specific SMBus support for the Tyan + S4985 motherboard. On this 4-CPU board, the SMBus is multiplexed + over 4 different channels, where the various memory module EEPROMs + live. Saying yes here will give you access to these in addition + to the trunk. + + This driver can also be built as a module. If so, the module + will be called i2c-nforce2-s4985. + +config I2C_SIS5595 + tristate "SiS 5595" + depends on PCI + help + If you say yes to this option, support will be included for the + SiS5595 SMBus (a subset of I2C) interface. + + This driver can also be built as a module. If so, the module + will be called i2c-sis5595. + +config I2C_SIS630 + tristate "SiS 630/730" + depends on PCI + help + If you say yes to this option, support will be included for the + SiS630 and SiS730 SMBus (a subset of I2C) interface. + + This driver can also be built as a module. If so, the module + will be called i2c-sis630. + +config I2C_SIS96X + tristate "SiS 96x" + depends on PCI + help + If you say yes to this option, support will be included for the SiS + 96x SMBus (a subset of I2C) interfaces. Specifically, the following + chipsets are supported: + 645/961 + 645DX/961 + 645DX/962 + 648/961 + 650/961 + 735 + 745 + + This driver can also be built as a module. If so, the module + will be called i2c-sis96x. + +config I2C_VIA + tristate "VIA VT82C586B" + depends on PCI && EXPERIMENTAL + select I2C_ALGOBIT + help + If you say yes to this option, support will be included for the VIA + 82C586B I2C interface + + This driver can also be built as a module. If so, the module + will be called i2c-via. + +config I2C_VIAPRO + tristate "VIA VT82C596/82C686/82xx and CX700" + depends on PCI + help + If you say yes to this option, support will be included for the VIA + VT82C596 and later SMBus interface. Specifically, the following + chipsets are supported: + VT82C596A/B + VT82C686A/B + VT8231 + VT8233/A + VT8235 + VT8237R/A/S + VT8251 + CX700 + + This driver can also be built as a module. If so, the module + will be called i2c-viapro. + +comment "Mac SMBus host controller drivers" + depends on PPC_CHRP || PPC_PMAC + +config I2C_HYDRA + tristate "CHRP Apple Hydra Mac I/O I2C interface" + depends on PCI && PPC_CHRP && EXPERIMENTAL + select I2C_ALGOBIT + help + This supports the use of the I2C interface in the Apple Hydra Mac + I/O chip on some CHRP machines (e.g. the LongTrail). Say Y if you + have such a machine. + + This support is also available as a module. If so, the module + will be called i2c-hydra. + +config I2C_POWERMAC + tristate "Powermac I2C interface" + depends on PPC_PMAC + default y + help + This exposes the various PowerMac i2c interfaces to the linux i2c + layer and to userland. It is used by various drivers on the PowerMac + platform, and should generally be enabled. + + This support is also available as a module. If so, the module + will be called i2c-powermac. + +comment "I2C system bus drivers (mostly embedded / system-on-chip)" + config I2C_AT91 tristate "Atmel AT91 I2C Two-Wire interface (TWI)" depends on ARCH_AT91 && EXPERIMENTAL && BROKEN @@ -101,10 +284,9 @@ config I2C_AU1550 config I2C_BLACKFIN_TWI tristate "Blackfin TWI I2C support" depends on BLACKFIN + depends on !BF561 && !BF531 && !BF532 && !BF533 help - This is the TWI I2C device driver for Blackfin BF522, BF525, - BF527, BF534, BF536, BF537 and BF54x. For other Blackfin processors, - please don't use this driver. + This is the I2C bus driver for Blackfin on-chip TWI interface. This driver can also be built as a module. If so, the module will be called i2c-bfin-twi. @@ -117,6 +299,16 @@ config I2C_BLACKFIN_TWI_CLK_KHZ help The unit of the TWI clock is kHz. +config I2C_CPM + tristate "Freescale CPM1 or CPM2 (MPC8xx/826x)" + depends on (CPM1 || CPM2) && OF_I2C + help + This supports the use of the I2C interface on Freescale + processors with CPM1 or CPM2. + + This driver can also be built as a module. If so, the module + will be called i2c-cpm. + config I2C_DAVINCI tristate "DaVinci I2C driver" depends on ARCH_DAVINCI @@ -130,17 +322,6 @@ config I2C_DAVINCI devices such as DaVinci NIC. For details please see http://www.ti.com/davinci -config I2C_ELEKTOR - tristate "Elektor ISA card" - depends on ISA && BROKEN_ON_SMP - select I2C_ALGOPCF - help - This supports the PCF8584 ISA bus I2C adapter. Say Y if you own - such an adapter. - - This support is also available as a module. If so, the module - will be called i2c-elektor. - config I2C_GPIO tristate "GPIO-based bitbanging I2C" depends on GENERIC_GPIO @@ -149,104 +330,6 @@ config I2C_GPIO This is a very simple bitbanging I2C driver utilizing the arch-neutral GPIO API to control the SCL and SDA lines. -config I2C_HYDRA - tristate "CHRP Apple Hydra Mac I/O I2C interface" - depends on PCI && PPC_CHRP && EXPERIMENTAL - select I2C_ALGOBIT - help - This supports the use of the I2C interface in the Apple Hydra Mac - I/O chip on some CHRP machines (e.g. the LongTrail). Say Y if you - have such a machine. - - This support is also available as a module. If so, the module - will be called i2c-hydra. - -config I2C_I801 - tristate "Intel 82801 (ICH)" - depends on PCI - help - If you say yes to this option, support will be included for the Intel - 801 family of mainboard I2C interfaces. Specifically, the following - versions of the chipset are supported: - 82801AA - 82801AB - 82801BA - 82801CA/CAM - 82801DB - 82801EB/ER (ICH5/ICH5R) - 6300ESB - ICH6 - ICH7 - ESB2 - ICH8 - ICH9 - Tolapai - ICH10 - - This driver can also be built as a module. If so, the module - will be called i2c-i801. - -config I2C_I810 - tristate "Intel 810/815 (DEPRECATED)" - default n - depends on PCI - select I2C_ALGOBIT - help - If you say yes to this option, support will be included for the Intel - 810/815 family of mainboard I2C interfaces. Specifically, the - following versions of the chipset are supported: - i810AA - i810AB - i810E - i815 - i845G - - This driver is deprecated in favor of the i810fb and intelfb drivers. - - This driver can also be built as a module. If so, the module - will be called i2c-i810. - -config I2C_PXA - tristate "Intel PXA2XX I2C adapter (EXPERIMENTAL)" - depends on EXPERIMENTAL && ARCH_PXA - help - If you have devices in the PXA I2C bus, say yes to this option. - This driver can also be built as a module. If so, the module - will be called i2c-pxa. - -config I2C_PXA_SLAVE - bool "Intel PXA2XX I2C Slave comms support" - depends on I2C_PXA - help - Support I2C slave mode communications on the PXA I2C bus. This - is necessary for systems where the PXA may be a target on the - I2C bus. - -config I2C_PIIX4 - tristate "Intel PIIX4 and compatible (ATI/Serverworks/Broadcom/SMSC)" - depends on PCI - help - If you say yes to this option, support will be included for the Intel - PIIX4 family of mainboard I2C interfaces. Specifically, the following - versions of the chipset are supported (note that Serverworks is part - of Broadcom): - Intel PIIX4 - Intel 440MX - ATI IXP200 - ATI IXP300 - ATI IXP400 - ATI SB600 - ATI SB700 - ATI SB800 - Serverworks OSB4 - Serverworks CSB5 - Serverworks CSB6 - Serverworks HT-1000 - SMSC Victory66 - - This driver can also be built as a module. If so, the module - will be called i2c-piix4. - config I2C_IBM_IIC tristate "IBM PPC 4xx on-chip I2C interface" depends on 4xx @@ -281,18 +364,6 @@ config I2C_IXP2000 This driver is deprecated and will be dropped soon. Use i2c-gpio instead. -config I2C_POWERMAC - tristate "Powermac I2C interface" - depends on PPC_PMAC - default y - help - This exposes the various PowerMac i2c interfaces to the linux i2c - layer and to userland. It is used by various drivers on the PowerMac - platform, and should generally be enabled. - - This support is also available as a module. If so, the module - will be called i2c-powermac. - config I2C_MPC tristate "MPC107/824x/85xx/52xx/86xx" depends on PPC32 @@ -305,15 +376,15 @@ config I2C_MPC This driver can also be built as a module. If so, the module will be called i2c-mpc. -config I2C_NFORCE2 - tristate "Nvidia nForce2, nForce3 and nForce4" - depends on PCI +config I2C_MV64XXX + tristate "Marvell mv64xxx I2C Controller" + depends on (MV64X60 || PLAT_ORION) && EXPERIMENTAL help - If you say yes to this option, support will be included for the Nvidia - nForce2, nForce3 and nForce4 families of mainboard I2C interfaces. + If you say yes to this option, support will be included for the + built-in I2C interface on the Marvell 64xxx line of host bridges. This driver can also be built as a module. If so, the module - will be called i2c-nforce2. + will be called i2c-mv64xxx. config I2C_OCORES tristate "OpenCores I2C Controller" @@ -336,76 +407,37 @@ config I2C_OMAP Like OMAP1510/1610/1710/5912 and OMAP242x. For details see http://www.ti.com/omap. -config I2C_PARPORT - tristate "Parallel port adapter" - depends on PARPORT - select I2C_ALGOBIT - help - This supports parallel port I2C adapters such as the ones made by - Philips or Velleman, Analog Devices evaluation boards, and more. - Basically any adapter using the parallel port as an I2C bus with - no extra chipset is supported by this driver, or could be. - - This driver is a replacement for (and was inspired by) an older - driver named i2c-philips-par. The new driver supports more devices, - and makes it easier to add support for new devices. - - An adapter type parameter is now mandatory. Please read the file - Documentation/i2c/busses/i2c-parport for details. - - Another driver exists, named i2c-parport-light, which doesn't depend - on the parport driver. This is meant for embedded systems. Don't say - Y here if you intend to say Y or M there. - - This support is also available as a module. If so, the module - will be called i2c-parport. - -config I2C_PARPORT_LIGHT - tristate "Parallel port adapter (light)" - select I2C_ALGOBIT - help - This supports parallel port I2C adapters such as the ones made by - Philips or Velleman, Analog Devices evaluation boards, and more. - Basically any adapter using the parallel port as an I2C bus with - no extra chipset is supported by this driver, or could be. - - This driver is a light version of i2c-parport. It doesn't depend - on the parport driver, and uses direct I/O access instead. This - might be preferred on embedded systems where wasting memory for - the clean but heavy parport handling is not an option. The - drawback is a reduced portability and the impossibility to - daisy-chain other parallel port devices. - - Don't say Y here if you said Y or M to i2c-parport. Saying M to - both is possible but both modules should not be loaded at the same - time. - - This support is also available as a module. If so, the module - will be called i2c-parport-light. - config I2C_PASEMI tristate "PA Semi SMBus interface" depends on PPC_PASEMI && PCI help Supports the PA Semi PWRficient on-chip SMBus interfaces. -config I2C_PROSAVAGE - tristate "S3/VIA (Pro)Savage (DEPRECATED)" - default n - depends on PCI - select I2C_ALGOBIT +config I2C_PNX + tristate "I2C bus support for Philips PNX targets" + depends on ARCH_PNX4008 help - If you say yes to this option, support will be included for the - I2C bus and DDC bus of the S3VIA embedded Savage4 and ProSavage8 - graphics processors. - chipsets supported: - S3/VIA KM266/VT8375 aka ProSavage8 - S3/VIA KM133/VT8365 aka Savage4 + This driver supports the Philips IP3204 I2C IP block master and/or + slave controller - This driver is deprecated in favor of the savagefb driver. + This driver can also be built as a module. If so, the module + will be called i2c-pnx. - This support is also available as a module. If so, the module - will be called i2c-prosavage. +config I2C_PXA + tristate "Intel PXA2XX I2C adapter (EXPERIMENTAL)" + depends on EXPERIMENTAL && ARCH_PXA + help + If you have devices in the PXA I2C bus, say yes to this option. + This driver can also be built as a module. If so, the module + will be called i2c-pxa. + +config I2C_PXA_SLAVE + bool "Intel PXA2XX I2C Slave comms support" + depends on I2C_PXA + help + Support I2C slave mode communications on the PXA I2C bus. This + is necessary for systems where the PXA may be a target on the + I2C bus. config I2C_S3C2410 tristate "S3C2410 I2C Driver" @@ -414,25 +446,24 @@ config I2C_S3C2410 Say Y here to include support for I2C controller in the Samsung S3C2410 based System-on-Chip devices. -config I2C_SAVAGE4 - tristate "S3 Savage 4 (DEPRECATED)" - default n - depends on PCI - select I2C_ALGOBIT +config I2C_SH7760 + tristate "Renesas SH7760 I2C Controller" + depends on CPU_SUBTYPE_SH7760 help - If you say yes to this option, support will be included for the - S3 Savage 4 I2C interface. - - This driver is deprecated in favor of the savagefb driver. + This driver supports the 2 I2C interfaces on the Renesas SH7760. This driver can also be built as a module. If so, the module - will be called i2c-savage4. + will be called i2c-sh7760. -config I2C_SIBYTE - tristate "SiByte SMBus interface" - depends on SIBYTE_SB1xxx_SOC +config I2C_SH_MOBILE + tristate "SuperH Mobile I2C Controller" + depends on SUPERH help - Supports the SiByte SOC on-chip I2C interfaces (2 channels). + If you say yes to this option, support will be included for the + built-in I2C interface on the Renesas SH-Mobile processor. + + This driver can also be built as a module. If so, the module + will be called i2c-sh_mobile. config I2C_SIMTEC tristate "Simtec Generic I2C interface" @@ -446,86 +477,65 @@ config I2C_SIMTEC This driver can also be built as a module. If so, the module will be called i2c-simtec. -config SCx200_I2C - tristate "NatSemi SCx200 I2C using GPIO pins (DEPRECATED)" - depends on SCx200_GPIO +config I2C_VERSATILE + tristate "ARM Versatile/Realview I2C bus support" + depends on ARCH_VERSATILE || ARCH_REALVIEW select I2C_ALGOBIT help - Enable the use of two GPIO pins of a SCx200 processor as an I2C bus. - - If you don't know what to do here, say N. + Say yes if you want to support the I2C serial bus on ARMs Versatile + range of platforms. - This support is also available as a module. If so, the module - will be called scx200_i2c. + This driver can also be built as a module. If so, the module + will be called i2c-versatile. - This driver is deprecated and will be dropped soon. Use i2c-gpio - (or scx200_acb) instead. +comment "External I2C/SMBus adapter drivers" -config SCx200_I2C_SCL - int "GPIO pin used for SCL" - depends on SCx200_I2C - default "12" +config I2C_PARPORT + tristate "Parallel port adapter" + depends on PARPORT + select I2C_ALGOBIT help - Enter the GPIO pin number used for the SCL signal. This value can - also be specified with a module parameter. + This supports parallel port I2C adapters such as the ones made by + Philips or Velleman, Analog Devices evaluation boards, and more. + Basically any adapter using the parallel port as an I2C bus with + no extra chipset is supported by this driver, or could be. -config SCx200_I2C_SDA - int "GPIO pin used for SDA" - depends on SCx200_I2C - default "13" - help - Enter the GPIO pin number used for the SSA signal. This value can - also be specified with a module parameter. + This driver is a replacement for (and was inspired by) an older + driver named i2c-philips-par. The new driver supports more devices, + and makes it easier to add support for new devices. -config SCx200_ACB - tristate "Geode ACCESS.bus support" - depends on X86_32 && PCI - help - Enable the use of the ACCESS.bus controllers on the Geode SCx200 and - SC1100 processors and the CS5535 and CS5536 Geode companion devices. + An adapter type parameter is now mandatory. Please read the file + Documentation/i2c/busses/i2c-parport for details. - If you don't know what to do here, say N. + Another driver exists, named i2c-parport-light, which doesn't depend + on the parport driver. This is meant for embedded systems. Don't say + Y here if you intend to say Y or M there. This support is also available as a module. If so, the module - will be called scx200_acb. - -config I2C_SIS5595 - tristate "SiS 5595" - depends on PCI - help - If you say yes to this option, support will be included for the - SiS5595 SMBus (a subset of I2C) interface. - - This driver can also be built as a module. If so, the module - will be called i2c-sis5595. + will be called i2c-parport. -config I2C_SIS630 - tristate "SiS 630/730" - depends on PCI +config I2C_PARPORT_LIGHT + tristate "Parallel port adapter (light)" + select I2C_ALGOBIT help - If you say yes to this option, support will be included for the - SiS630 and SiS730 SMBus (a subset of I2C) interface. + This supports parallel port I2C adapters such as the ones made by + Philips or Velleman, Analog Devices evaluation boards, and more. + Basically any adapter using the parallel port as an I2C bus with + no extra chipset is supported by this driver, or could be. - This driver can also be built as a module. If so, the module - will be called i2c-sis630. + This driver is a light version of i2c-parport. It doesn't depend + on the parport driver, and uses direct I/O access instead. This + might be preferred on embedded systems where wasting memory for + the clean but heavy parport handling is not an option. The + drawback is a reduced portability and the impossibility to + daisy-chain other parallel port devices. -config I2C_SIS96X - tristate "SiS 96x" - depends on PCI - help - If you say yes to this option, support will be included for the SiS - 96x SMBus (a subset of I2C) interfaces. Specifically, the following - chipsets are supported: - 645/961 - 645DX/961 - 645DX/962 - 648/961 - 650/961 - 735 - 745 + Don't say Y here if you said Y or M to i2c-parport. Saying M to + both is possible but both modules should not be loaded at the same + time. - This driver can also be built as a module. If so, the module - will be called i2c-sis96x. + This support is also available as a module. If so, the module + will be called i2c-parport-light. config I2C_TAOS_EVM tristate "TAOS evaluation module" @@ -543,21 +553,8 @@ config I2C_TAOS_EVM This support is also available as a module. If so, the module will be called i2c-taos-evm. -config I2C_STUB - tristate "I2C/SMBus Test Stub" - depends on EXPERIMENTAL && m - default 'n' - help - This module may be useful to developers of SMBus client drivers, - especially for certain kinds of sensor chips. - - If you do build this module, be sure to read the notes and warnings - in <file:Documentation/i2c/i2c-stub>. - - If you don't know what to do here, definitely say N. - config I2C_TINY_USB - tristate "I2C-Tiny-USB" + tristate "Tiny-USB adapter" depends on USB help If you say yes to this option, support will be included for the @@ -567,16 +564,21 @@ config I2C_TINY_USB This driver can also be built as a module. If so, the module will be called i2c-tiny-usb. -config I2C_VERSATILE - tristate "ARM Versatile/Realview I2C bus support" - depends on ARCH_VERSATILE || ARCH_REALVIEW +comment "Graphics adapter I2C/DDC channel drivers" + depends on PCI + +config I2C_VOODOO3 + tristate "Voodoo 3" + depends on PCI select I2C_ALGOBIT help - Say yes if you want to support the I2C serial bus on ARMs Versatile - range of platforms. + If you say yes to this option, support will be included for the + Voodoo 3 I2C interface. This driver can also be built as a module. If so, the module - will be called i2c-versatile. + will be called i2c-voodoo3. + +comment "Other I2C/SMBus bus drivers" config I2C_ACORN tristate "Acorn IOC/IOMD I2C bus support" @@ -588,46 +590,16 @@ config I2C_ACORN If you don't know, say Y. -config I2C_VIA - tristate "VIA 82C586B" - depends on PCI && EXPERIMENTAL - select I2C_ALGOBIT - help - If you say yes to this option, support will be included for the VIA - 82C586B I2C interface - - This driver can also be built as a module. If so, the module - will be called i2c-via. - -config I2C_VIAPRO - tristate "VIA VT82C596/82C686/82xx and CX700" - depends on PCI - help - If you say yes to this option, support will be included for the VIA - VT82C596 and later SMBus interface. Specifically, the following - chipsets are supported: - VT82C596A/B - VT82C686A/B - VT8231 - VT8233/A - VT8235 - VT8237R/A/S - VT8251 - CX700 - - This driver can also be built as a module. If so, the module - will be called i2c-viapro. - -config I2C_VOODOO3 - tristate "Voodoo 3" - depends on PCI - select I2C_ALGOBIT +config I2C_ELEKTOR + tristate "Elektor ISA card" + depends on ISA && BROKEN_ON_SMP + select I2C_ALGOPCF help - If you say yes to this option, support will be included for the - Voodoo 3 I2C interface. + This supports the PCF8584 ISA bus I2C adapter. Say Y if you own + such an adapter. - This driver can also be built as a module. If so, the module - will be called i2c-voodoo3. + This support is also available as a module. If so, the module + will be called i2c-elektor. config I2C_PCA_ISA tristate "PCA9564 on an ISA bus" @@ -657,26 +629,6 @@ config I2C_PCA_PLATFORM This driver can also be built as a module. If so, the module will be called i2c-pca-platform. -config I2C_MV64XXX - tristate "Marvell mv64xxx I2C Controller" - depends on (MV64X60 || PLAT_ORION) && EXPERIMENTAL - help - If you say yes to this option, support will be included for the - built-in I2C interface on the Marvell 64xxx line of host bridges. - - This driver can also be built as a module. If so, the module - will be called i2c-mv64xxx. - -config I2C_PNX - tristate "I2C bus support for Philips PNX targets" - depends on ARCH_PNX4008 - help - This driver supports the Philips IP3204 I2C IP block master and/or - slave controller - - This driver can also be built as a module. If so, the module - will be called i2c-pnx. - config I2C_PMCMSP tristate "PMC MSP I2C TWI Controller" depends on PMC_MSP @@ -686,23 +638,66 @@ config I2C_PMCMSP This driver can also be built as module. If so, the module will be called i2c-pmcmsp. -config I2C_SH7760 - tristate "Renesas SH7760 I2C Controller" - depends on CPU_SUBTYPE_SH7760 +config I2C_SIBYTE + tristate "SiByte SMBus interface" + depends on SIBYTE_SB1xxx_SOC help - This driver supports the 2 I2C interfaces on the Renesas SH7760. + Supports the SiByte SOC on-chip I2C interfaces (2 channels). - This driver can also be built as a module. If so, the module - will be called i2c-sh7760. +config I2C_STUB + tristate "I2C/SMBus Test Stub" + depends on EXPERIMENTAL && m + default 'n' + help + This module may be useful to developers of SMBus client drivers, + especially for certain kinds of sensor chips. -config I2C_SH_MOBILE - tristate "SuperH Mobile I2C Controller" - depends on SUPERH + If you do build this module, be sure to read the notes and warnings + in <file:Documentation/i2c/i2c-stub>. + + If you don't know what to do here, definitely say N. + +config SCx200_I2C + tristate "NatSemi SCx200 I2C using GPIO pins (DEPRECATED)" + depends on SCx200_GPIO + select I2C_ALGOBIT help - If you say yes to this option, support will be included for the - built-in I2C interface on the Renesas SH-Mobile processor. + Enable the use of two GPIO pins of a SCx200 processor as an I2C bus. - This driver can also be built as a module. If so, the module - will be called i2c-sh_mobile. + If you don't know what to do here, say N. + + This support is also available as a module. If so, the module + will be called scx200_i2c. + + This driver is deprecated and will be dropped soon. Use i2c-gpio + (or scx200_acb) instead. + +config SCx200_I2C_SCL + int "GPIO pin used for SCL" + depends on SCx200_I2C + default "12" + help + Enter the GPIO pin number used for the SCL signal. This value can + also be specified with a module parameter. + +config SCx200_I2C_SDA + int "GPIO pin used for SDA" + depends on SCx200_I2C + default "13" + help + Enter the GPIO pin number used for the SSA signal. This value can + also be specified with a module parameter. + +config SCx200_ACB + tristate "Geode ACCESS.bus support" + depends on X86_32 && PCI + help + Enable the use of the ACCESS.bus controllers on the Geode SCx200 and + SC1100 processors and the CS5535 and CS5536 Geode companion devices. + + If you don't know what to do here, say N. + + This support is also available as a module. If so, the module + will be called scx200_acb. endmenu diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile index e8c882a5ea66..97dbfa2107fe 100644 --- a/drivers/i2c/busses/Makefile +++ b/drivers/i2c/busses/Makefile @@ -2,57 +2,68 @@ # Makefile for the i2c bus drivers. # +# PC SMBus host controller drivers obj-$(CONFIG_I2C_ALI1535) += i2c-ali1535.o obj-$(CONFIG_I2C_ALI1563) += i2c-ali1563.o obj-$(CONFIG_I2C_ALI15X3) += i2c-ali15x3.o obj-$(CONFIG_I2C_AMD756) += i2c-amd756.o obj-$(CONFIG_I2C_AMD756_S4882) += i2c-amd756-s4882.o obj-$(CONFIG_I2C_AMD8111) += i2c-amd8111.o +obj-$(CONFIG_I2C_I801) += i2c-i801.o +obj-$(CONFIG_I2C_ISCH) += i2c-isch.o +obj-$(CONFIG_I2C_NFORCE2) += i2c-nforce2.o +obj-$(CONFIG_I2C_NFORCE2_S4985) += i2c-nforce2-s4985.o +obj-$(CONFIG_I2C_PIIX4) += i2c-piix4.o +obj-$(CONFIG_I2C_SIS5595) += i2c-sis5595.o +obj-$(CONFIG_I2C_SIS630) += i2c-sis630.o +obj-$(CONFIG_I2C_SIS96X) += i2c-sis96x.o +obj-$(CONFIG_I2C_VIA) += i2c-via.o +obj-$(CONFIG_I2C_VIAPRO) += i2c-viapro.o + +# Mac SMBus host controller drivers +obj-$(CONFIG_I2C_HYDRA) += i2c-hydra.o +obj-$(CONFIG_I2C_POWERMAC) += i2c-powermac.o + +# Embebbed system I2C/SMBus host controller drivers obj-$(CONFIG_I2C_AT91) += i2c-at91.o obj-$(CONFIG_I2C_AU1550) += i2c-au1550.o obj-$(CONFIG_I2C_BLACKFIN_TWI) += i2c-bfin-twi.o +obj-$(CONFIG_I2C_CPM) += i2c-cpm.o obj-$(CONFIG_I2C_DAVINCI) += i2c-davinci.o -obj-$(CONFIG_I2C_ELEKTOR) += i2c-elektor.o obj-$(CONFIG_I2C_GPIO) += i2c-gpio.o -obj-$(CONFIG_I2C_HYDRA) += i2c-hydra.o -obj-$(CONFIG_I2C_I801) += i2c-i801.o -obj-$(CONFIG_I2C_I810) += i2c-i810.o obj-$(CONFIG_I2C_IBM_IIC) += i2c-ibm_iic.o obj-$(CONFIG_I2C_IOP3XX) += i2c-iop3xx.o obj-$(CONFIG_I2C_IXP2000) += i2c-ixp2000.o -obj-$(CONFIG_I2C_POWERMAC) += i2c-powermac.o obj-$(CONFIG_I2C_MPC) += i2c-mpc.o obj-$(CONFIG_I2C_MV64XXX) += i2c-mv64xxx.o -obj-$(CONFIG_I2C_NFORCE2) += i2c-nforce2.o obj-$(CONFIG_I2C_OCORES) += i2c-ocores.o obj-$(CONFIG_I2C_OMAP) += i2c-omap.o -obj-$(CONFIG_I2C_PARPORT) += i2c-parport.o -obj-$(CONFIG_I2C_PARPORT_LIGHT) += i2c-parport-light.o obj-$(CONFIG_I2C_PASEMI) += i2c-pasemi.o -obj-$(CONFIG_I2C_PCA_ISA) += i2c-pca-isa.o -obj-$(CONFIG_I2C_PCA_PLATFORM) += i2c-pca-platform.o -obj-$(CONFIG_I2C_PIIX4) += i2c-piix4.o -obj-$(CONFIG_I2C_PMCMSP) += i2c-pmcmsp.o obj-$(CONFIG_I2C_PNX) += i2c-pnx.o -obj-$(CONFIG_I2C_PROSAVAGE) += i2c-prosavage.o obj-$(CONFIG_I2C_PXA) += i2c-pxa.o obj-$(CONFIG_I2C_S3C2410) += i2c-s3c2410.o -obj-$(CONFIG_I2C_SAVAGE4) += i2c-savage4.o obj-$(CONFIG_I2C_SH7760) += i2c-sh7760.o obj-$(CONFIG_I2C_SH_MOBILE) += i2c-sh_mobile.o -obj-$(CONFIG_I2C_SIBYTE) += i2c-sibyte.o obj-$(CONFIG_I2C_SIMTEC) += i2c-simtec.o -obj-$(CONFIG_I2C_SIS5595) += i2c-sis5595.o -obj-$(CONFIG_I2C_SIS630) += i2c-sis630.o -obj-$(CONFIG_I2C_SIS96X) += i2c-sis96x.o -obj-$(CONFIG_I2C_STUB) += i2c-stub.o +obj-$(CONFIG_I2C_VERSATILE) += i2c-versatile.o + +# External I2C/SMBus adapter drivers +obj-$(CONFIG_I2C_PARPORT) += i2c-parport.o +obj-$(CONFIG_I2C_PARPORT_LIGHT) += i2c-parport-light.o obj-$(CONFIG_I2C_TAOS_EVM) += i2c-taos-evm.o obj-$(CONFIG_I2C_TINY_USB) += i2c-tiny-usb.o -obj-$(CONFIG_I2C_VERSATILE) += i2c-versatile.o -obj-$(CONFIG_I2C_ACORN) += i2c-acorn.o -obj-$(CONFIG_I2C_VIA) += i2c-via.o -obj-$(CONFIG_I2C_VIAPRO) += i2c-viapro.o + +# Graphics adapter I2C/DDC channel drivers obj-$(CONFIG_I2C_VOODOO3) += i2c-voodoo3.o + +# Other I2C/SMBus bus drivers +obj-$(CONFIG_I2C_ACORN) += i2c-acorn.o +obj-$(CONFIG_I2C_ELEKTOR) += i2c-elektor.o +obj-$(CONFIG_I2C_PCA_ISA) += i2c-pca-isa.o +obj-$(CONFIG_I2C_PCA_PLATFORM) += i2c-pca-platform.o +obj-$(CONFIG_I2C_PMCMSP) += i2c-pmcmsp.o +obj-$(CONFIG_I2C_SIBYTE) += i2c-sibyte.o +obj-$(CONFIG_I2C_STUB) += i2c-stub.o obj-$(CONFIG_SCx200_ACB) += scx200_acb.o obj-$(CONFIG_SCx200_I2C) += scx200_i2c.o diff --git a/drivers/i2c/busses/i2c-ali1535.c b/drivers/i2c/busses/i2c-ali1535.c index f14372ac2fc5..9cead9b9458e 100644 --- a/drivers/i2c/busses/i2c-ali1535.c +++ b/drivers/i2c/busses/i2c-ali1535.c @@ -1,6 +1,4 @@ /* - i2c-ali1535.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring Copyright (c) 2000 Frodo Looijaard <frodol@dds.nl>, Philip Edelbrock <phil@netroedge.com>, Mark D. Studebaker <mdsxyz123@yahoo.com>, @@ -61,6 +59,7 @@ #include <linux/ioport.h> #include <linux/i2c.h> #include <linux/init.h> +#include <linux/acpi.h> #include <asm/io.h> @@ -159,6 +158,11 @@ static int ali1535_setup(struct pci_dev *dev) goto exit; } + retval = acpi_check_region(ali1535_smba, ALI1535_SMB_IOSIZE, + ali1535_driver.name); + if (retval) + goto exit; + if (!request_region(ali1535_smba, ALI1535_SMB_IOSIZE, ali1535_driver.name)) { dev_err(&dev->dev, "ALI1535_smb region 0x%x already in use!\n", @@ -259,7 +263,7 @@ static int ali1535_transaction(struct i2c_adapter *adap) dev_err(&adap->dev, "SMBus reset failed! (0x%02x) - controller or " "device on bus is probably hung\n", temp); - return -1; + return -EBUSY; } } else { /* check and clear done bit */ @@ -281,12 +285,12 @@ static int ali1535_transaction(struct i2c_adapter *adap) /* If the SMBus is still busy, we give up */ if (timeout >= MAX_TIMEOUT) { - result = -1; + result = -ETIMEDOUT; dev_err(&adap->dev, "SMBus Timeout!\n"); } if (temp & ALI1535_STS_FAIL) { - result = -1; + result = -EIO; dev_dbg(&adap->dev, "Error: Failed bus transaction\n"); } @@ -295,7 +299,7 @@ static int ali1535_transaction(struct i2c_adapter *adap) * do a printk. This means that bus collisions go unreported. */ if (temp & ALI1535_STS_BUSERR) { - result = -1; + result = -ENXIO; dev_dbg(&adap->dev, "Error: no response or bus collision ADD=%02x\n", inb_p(SMBHSTADD)); @@ -303,13 +307,13 @@ static int ali1535_transaction(struct i2c_adapter *adap) /* haven't ever seen this */ if (temp & ALI1535_STS_DEV) { - result = -1; + result = -EIO; dev_err(&adap->dev, "Error: device error\n"); } /* check to see if the "command complete" indication is set */ if (!(temp & ALI1535_STS_DONE)) { - result = -1; + result = -ETIMEDOUT; dev_err(&adap->dev, "Error: command never completed\n"); } @@ -332,7 +336,7 @@ static int ali1535_transaction(struct i2c_adapter *adap) return result; } -/* Return -1 on error. */ +/* Return negative errno on error. */ static s32 ali1535_access(struct i2c_adapter *adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data *data) @@ -357,10 +361,6 @@ static s32 ali1535_access(struct i2c_adapter *adap, u16 addr, outb_p(0xFF, SMBHSTSTS); switch (size) { - case I2C_SMBUS_PROC_CALL: - dev_err(&adap->dev, "I2C_SMBUS_PROC_CALL not supported!\n"); - result = -1; - goto EXIT; case I2C_SMBUS_QUICK: outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), SMBHSTADD); @@ -418,13 +418,15 @@ static s32 ali1535_access(struct i2c_adapter *adap, u16 addr, outb_p(data->block[i], SMBBLKDAT); } break; + default: + dev_warn(&adap->dev, "Unsupported transaction %d\n", size); + result = -EOPNOTSUPP; + goto EXIT; } - if (ali1535_transaction(adap)) { - /* Error in transaction */ - result = -1; + result = ali1535_transaction(adap); + if (result) goto EXIT; - } if ((read_write == I2C_SMBUS_WRITE) || (size == ALI1535_QUICK)) { result = 0; @@ -475,7 +477,7 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter ali1535_adapter = { .owner = THIS_MODULE, .id = I2C_HW_SMBUS_ALI1535, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-ali1563.c b/drivers/i2c/busses/i2c-ali1563.c index 6b68074e518a..fc3e5b026423 100644 --- a/drivers/i2c/busses/i2c-ali1563.c +++ b/drivers/i2c/busses/i2c-ali1563.c @@ -21,6 +21,7 @@ #include <linux/i2c.h> #include <linux/pci.h> #include <linux/init.h> +#include <linux/acpi.h> #define ALI1563_MAX_TIMEOUT 500 #define ALI1563_SMBBA 0x80 @@ -67,6 +68,7 @@ static int ali1563_transaction(struct i2c_adapter * a, int size) { u32 data; int timeout; + int status = -EIO; dev_dbg(&a->dev, "Transaction (pre): STS=%02x, CNTL1=%02x, " "CNTL2=%02x, CMD=%02x, ADD=%02x, DAT0=%02x, DAT1=%02x\n", @@ -103,13 +105,15 @@ static int ali1563_transaction(struct i2c_adapter * a, int size) /* Issue 'kill' to host controller */ outb_p(HST_CNTL2_KILL,SMB_HST_CNTL2); data = inb_p(SMB_HST_STS); + status = -ETIMEDOUT; } /* device error - no response, ignore the autodetection case */ - if ((data & HST_STS_DEVERR) && (size != HST_CNTL2_QUICK)) { - dev_err(&a->dev, "Device error!\n"); + if (data & HST_STS_DEVERR) { + if (size != HST_CNTL2_QUICK) + dev_err(&a->dev, "Device error!\n"); + status = -ENXIO; } - /* bus collision */ if (data & HST_STS_BUSERR) { dev_err(&a->dev, "Bus collision!\n"); @@ -122,13 +126,14 @@ static int ali1563_transaction(struct i2c_adapter * a, int size) outb_p(0x0,SMB_HST_CNTL2); } - return -1; + return status; } static int ali1563_block_start(struct i2c_adapter * a) { u32 data; int timeout; + int status = -EIO; dev_dbg(&a->dev, "Block (pre): STS=%02x, CNTL1=%02x, " "CNTL2=%02x, CMD=%02x, ADD=%02x, DAT0=%02x, DAT1=%02x\n", @@ -164,13 +169,20 @@ static int ali1563_block_start(struct i2c_adapter * a) if (timeout && !(data & HST_STS_BAD)) return 0; + + if (timeout == 0) + status = -ETIMEDOUT; + + if (data & HST_STS_DEVERR) + status = -ENXIO; + dev_err(&a->dev, "SMBus Error: %s%s%s%s%s\n", - timeout ? "Timeout " : "", + timeout ? "" : "Timeout ", data & HST_STS_FAIL ? "Transaction Failed " : "", data & HST_STS_BUSERR ? "No response or Bus Collision " : "", data & HST_STS_DEVERR ? "Device Error " : "", !(data & HST_STS_DONE) ? "Transaction Never Finished " : ""); - return -1; + return status; } static int ali1563_block(struct i2c_adapter * a, union i2c_smbus_data * data, u8 rw) @@ -235,10 +247,6 @@ static s32 ali1563_access(struct i2c_adapter * a, u16 addr, /* Map the size to what the chip understands */ switch (size) { - case I2C_SMBUS_PROC_CALL: - dev_err(&a->dev, "I2C_SMBUS_PROC_CALL not supported!\n"); - error = -EINVAL; - break; case I2C_SMBUS_QUICK: size = HST_CNTL2_QUICK; break; @@ -254,6 +262,10 @@ static s32 ali1563_access(struct i2c_adapter * a, u16 addr, case I2C_SMBUS_BLOCK_DATA: size = HST_CNTL2_BLOCK; break; + default: + dev_warn(&a->dev, "Unsupported transaction %d\n", size); + error = -EOPNOTSUPP; + goto Done; } outb_p(((addr & 0x7f) << 1) | (rw & 0x01), SMB_HST_ADD); @@ -345,6 +357,10 @@ static int __devinit ali1563_setup(struct pci_dev * dev) } } + if (acpi_check_region(ali1563_smba, ALI1563_SMB_IOSIZE, + ali1563_pci_driver.name)) + goto Err; + if (!request_region(ali1563_smba, ALI1563_SMB_IOSIZE, ali1563_pci_driver.name)) { dev_err(&dev->dev, "Could not allocate I/O space at 0x%04x\n", @@ -371,7 +387,7 @@ static const struct i2c_algorithm ali1563_algorithm = { static struct i2c_adapter ali1563_adapter = { .owner = THIS_MODULE, .id = I2C_HW_SMBUS_ALI1563, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &ali1563_algorithm, }; diff --git a/drivers/i2c/busses/i2c-ali15x3.c b/drivers/i2c/busses/i2c-ali15x3.c index 93bf87d70961..234fdde7d40e 100644 --- a/drivers/i2c/busses/i2c-ali15x3.c +++ b/drivers/i2c/busses/i2c-ali15x3.c @@ -1,6 +1,4 @@ /* - ali15x3.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring Copyright (c) 1999 Frodo Looijaard <frodol@dds.nl> and Philip Edelbrock <phil@netroedge.com> and Mark D. Studebaker <mdsxyz123@yahoo.com> @@ -68,6 +66,7 @@ #include <linux/delay.h> #include <linux/i2c.h> #include <linux/init.h> +#include <linux/acpi.h> #include <asm/io.h> /* ALI15X3 SMBus address offsets */ @@ -166,6 +165,10 @@ static int ali15x3_setup(struct pci_dev *ALI15X3_dev) if(force_addr) ali15x3_smba = force_addr & ~(ALI15X3_SMB_IOSIZE - 1); + if (acpi_check_region(ali15x3_smba, ALI15X3_SMB_IOSIZE, + ali15x3_driver.name)) + return -EBUSY; + if (!request_region(ali15x3_smba, ALI15X3_SMB_IOSIZE, ali15x3_driver.name)) { dev_err(&ALI15X3_dev->dev, @@ -282,7 +285,7 @@ static int ali15x3_transaction(struct i2c_adapter *adap) dev_err(&adap->dev, "SMBus reset failed! (0x%02x) - " "controller or device on bus is probably hung\n", temp); - return -1; + return -EBUSY; } } else { /* check and clear done bit */ @@ -304,12 +307,12 @@ static int ali15x3_transaction(struct i2c_adapter *adap) /* If the SMBus is still busy, we give up */ if (timeout >= MAX_TIMEOUT) { - result = -1; + result = -ETIMEDOUT; dev_err(&adap->dev, "SMBus Timeout!\n"); } if (temp & ALI15X3_STS_TERM) { - result = -1; + result = -EIO; dev_dbg(&adap->dev, "Error: Failed bus transaction\n"); } @@ -320,7 +323,7 @@ static int ali15x3_transaction(struct i2c_adapter *adap) This means that bus collisions go unreported. */ if (temp & ALI15X3_STS_COLL) { - result = -1; + result = -ENXIO; dev_dbg(&adap->dev, "Error: no response or bus collision ADD=%02x\n", inb_p(SMBHSTADD)); @@ -328,7 +331,7 @@ static int ali15x3_transaction(struct i2c_adapter *adap) /* haven't ever seen this */ if (temp & ALI15X3_STS_DEV) { - result = -1; + result = -EIO; dev_err(&adap->dev, "Error: device error\n"); } dev_dbg(&adap->dev, "Transaction (post): STS=%02x, CNT=%02x, CMD=%02x, " @@ -338,7 +341,7 @@ static int ali15x3_transaction(struct i2c_adapter *adap) return result; } -/* Return -1 on error. */ +/* Return negative errno on error. */ static s32 ali15x3_access(struct i2c_adapter * adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data * data) @@ -362,9 +365,6 @@ static s32 ali15x3_access(struct i2c_adapter * adap, u16 addr, } switch (size) { - case I2C_SMBUS_PROC_CALL: - dev_err(&adap->dev, "I2C_SMBUS_PROC_CALL not supported!\n"); - return -1; case I2C_SMBUS_QUICK: outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), SMBHSTADD); @@ -417,12 +417,16 @@ static s32 ali15x3_access(struct i2c_adapter * adap, u16 addr, } size = ALI15X3_BLOCK_DATA; break; + default: + dev_warn(&adap->dev, "Unsupported transaction %d\n", size); + return -EOPNOTSUPP; } outb_p(size, SMBHSTCNT); /* output command */ - if (ali15x3_transaction(adap)) /* Error in transaction */ - return -1; + temp = ali15x3_transaction(adap); + if (temp) + return temp; if ((read_write == I2C_SMBUS_WRITE) || (size == ALI15X3_QUICK)) return 0; @@ -470,7 +474,7 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter ali15x3_adapter = { .owner = THIS_MODULE, .id = I2C_HW_SMBUS_ALI15X3, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-amd756-s4882.c b/drivers/i2c/busses/i2c-amd756-s4882.c index c38a0a112208..72872d1e63ef 100644 --- a/drivers/i2c/busses/i2c-amd756-s4882.c +++ b/drivers/i2c/busses/i2c-amd756-s4882.c @@ -58,7 +58,7 @@ static s32 amd756_access_virt0(struct i2c_adapter * adap, u16 addr, /* We exclude the multiplexed addresses */ if (addr == 0x4c || (addr & 0xfc) == 0x50 || (addr & 0xfc) == 0x30 || addr == 0x18) - return -1; + return -ENXIO; mutex_lock(&amd756_lock); @@ -86,7 +86,7 @@ static inline s32 amd756_access_channel(struct i2c_adapter * adap, u16 addr, /* We exclude the non-multiplexed addresses */ if (addr != 0x4c && (addr & 0xfc) != 0x50 && (addr & 0xfc) != 0x30) - return -1; + return -ENXIO; mutex_lock(&amd756_lock); @@ -155,6 +155,16 @@ static int __init amd756_s4882_init(void) int i, error; union i2c_smbus_data ioconfig; + /* Configure the PCA9556 multiplexer */ + ioconfig.byte = 0x00; /* All I/O to output mode */ + error = i2c_smbus_xfer(&amd756_smbus, 0x18, 0, I2C_SMBUS_WRITE, 0x03, + I2C_SMBUS_BYTE_DATA, &ioconfig); + if (error) { + dev_err(&amd756_smbus.dev, "PCA9556 configuration failed\n"); + error = -EIO; + goto ERROR0; + } + /* Unregister physical bus */ error = i2c_del_adapter(&amd756_smbus); if (error) { @@ -198,22 +208,11 @@ static int __init amd756_s4882_init(void) s4882_algo[3].smbus_xfer = amd756_access_virt3; s4882_algo[4].smbus_xfer = amd756_access_virt4; - /* Configure the PCA9556 multiplexer */ - ioconfig.byte = 0x00; /* All I/O to output mode */ - error = amd756_smbus.algo->smbus_xfer(&amd756_smbus, 0x18, 0, - I2C_SMBUS_WRITE, 0x03, - I2C_SMBUS_BYTE_DATA, &ioconfig); - if (error) { - dev_err(&amd756_smbus.dev, "PCA9556 configuration failed\n"); - error = -EIO; - goto ERROR3; - } - /* Register virtual adapters */ for (i = 0; i < 5; i++) { error = i2c_add_adapter(s4882_adapter+i); if (error) { - dev_err(&amd756_smbus.dev, + printk(KERN_ERR "i2c-amd756-s4882: " "Virtual adapter %d registration " "failed, module not inserted\n", i); for (i--; i >= 0; i--) @@ -252,8 +251,8 @@ static void __exit amd756_s4882_exit(void) /* Restore physical bus */ if (i2c_add_adapter(&amd756_smbus)) - dev_err(&amd756_smbus.dev, "Physical bus restoration " - "failed\n"); + printk(KERN_ERR "i2c-amd756-s4882: " + "Physical bus restoration failed\n"); } MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>"); diff --git a/drivers/i2c/busses/i2c-amd756.c b/drivers/i2c/busses/i2c-amd756.c index 43508d61eb7c..1ea39254dac6 100644 --- a/drivers/i2c/busses/i2c-amd756.c +++ b/drivers/i2c/busses/i2c-amd756.c @@ -1,7 +1,4 @@ /* - amd756.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring - Copyright (c) 1999-2002 Merlin Hughes <merlin@merlin.org> Shamelessly ripped from i2c-piix4.c: @@ -45,6 +42,7 @@ #include <linux/ioport.h> #include <linux/i2c.h> #include <linux/init.h> +#include <linux/acpi.h> #include <asm/io.h> /* AMD756 SMBus address offsets */ @@ -151,17 +149,17 @@ static int amd756_transaction(struct i2c_adapter *adap) } if (temp & GS_PRERR_STS) { - result = -1; + result = -ENXIO; dev_dbg(&adap->dev, "SMBus Protocol error (no response)!\n"); } if (temp & GS_COL_STS) { - result = -1; + result = -EIO; dev_warn(&adap->dev, "SMBus collision!\n"); } if (temp & GS_TO_STS) { - result = -1; + result = -ETIMEDOUT; dev_dbg(&adap->dev, "SMBus protocol timeout!\n"); } @@ -189,22 +187,18 @@ static int amd756_transaction(struct i2c_adapter *adap) outw_p(inw(SMB_GLOBAL_ENABLE) | GE_ABORT, SMB_GLOBAL_ENABLE); msleep(100); outw_p(GS_CLEAR_STS, SMB_GLOBAL_STATUS); - return -1; + return -EIO; } -/* Return -1 on error. */ +/* Return negative errno on error. */ static s32 amd756_access(struct i2c_adapter * adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data * data) { int i, len; + int status; - /** TODO: Should I supporte the 10-bit transfers? */ switch (size) { - case I2C_SMBUS_PROC_CALL: - dev_dbg(&adap->dev, "I2C_SMBUS_PROC_CALL not supported!\n"); - /* TODO: Well... It is supported, I'm just not sure what to do here... */ - return -1; case I2C_SMBUS_QUICK: outw_p(((addr & 0x7f) << 1) | (read_write & 0x01), SMB_HOST_ADDRESS); @@ -251,13 +245,17 @@ static s32 amd756_access(struct i2c_adapter * adap, u16 addr, } size = AMD756_BLOCK_DATA; break; + default: + dev_warn(&adap->dev, "Unsupported transaction %d\n", size); + return -EOPNOTSUPP; } /* How about enabling interrupts... */ outw_p(size & GE_CYC_TYPE_MASK, SMB_GLOBAL_ENABLE); - if (amd756_transaction(adap)) /* Error in transaction */ - return -1; + status = amd756_transaction(adap); + if (status) + return status; if ((read_write == I2C_SMBUS_WRITE) || (size == AMD756_QUICK)) return 0; @@ -301,7 +299,7 @@ static const struct i2c_algorithm smbus_algorithm = { struct i2c_adapter amd756_smbus = { .owner = THIS_MODULE, .id = I2C_HW_SMBUS_AMD756, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; @@ -368,6 +366,11 @@ static int __devinit amd756_probe(struct pci_dev *pdev, amd756_ioport += SMB_ADDR_OFFSET; } + error = acpi_check_region(amd756_ioport, SMB_IOSIZE, + amd756_driver.name); + if (error) + return error; + if (!request_region(amd756_ioport, SMB_IOSIZE, amd756_driver.name)) { dev_err(&pdev->dev, "SMB region 0x%x already in use!\n", amd756_ioport); diff --git a/drivers/i2c/busses/i2c-amd8111.c b/drivers/i2c/busses/i2c-amd8111.c index 5d1a27ef2504..3972208876b3 100644 --- a/drivers/i2c/busses/i2c-amd8111.c +++ b/drivers/i2c/busses/i2c-amd8111.c @@ -16,6 +16,7 @@ #include <linux/init.h> #include <linux/i2c.h> #include <linux/delay.h> +#include <linux/acpi.h> #include <asm/io.h> MODULE_LICENSE("GPL"); @@ -77,7 +78,7 @@ static unsigned int amd_ec_wait_write(struct amd_smbus *smbus) if (!timeout) { dev_warn(&smbus->dev->dev, "Timeout while waiting for IBF to clear\n"); - return -1; + return -ETIMEDOUT; } return 0; @@ -93,7 +94,7 @@ static unsigned int amd_ec_wait_read(struct amd_smbus *smbus) if (!timeout) { dev_warn(&smbus->dev->dev, "Timeout while waiting for OBF to set\n"); - return -1; + return -ETIMEDOUT; } return 0; @@ -102,16 +103,21 @@ static unsigned int amd_ec_wait_read(struct amd_smbus *smbus) static unsigned int amd_ec_read(struct amd_smbus *smbus, unsigned char address, unsigned char *data) { - if (amd_ec_wait_write(smbus)) - return -1; + int status; + + status = amd_ec_wait_write(smbus); + if (status) + return status; outb(AMD_EC_CMD_RD, smbus->base + AMD_EC_CMD); - if (amd_ec_wait_write(smbus)) - return -1; + status = amd_ec_wait_write(smbus); + if (status) + return status; outb(address, smbus->base + AMD_EC_DATA); - if (amd_ec_wait_read(smbus)) - return -1; + status = amd_ec_wait_read(smbus); + if (status) + return status; *data = inb(smbus->base + AMD_EC_DATA); return 0; @@ -120,16 +126,21 @@ static unsigned int amd_ec_read(struct amd_smbus *smbus, unsigned char address, static unsigned int amd_ec_write(struct amd_smbus *smbus, unsigned char address, unsigned char data) { - if (amd_ec_wait_write(smbus)) - return -1; + int status; + + status = amd_ec_wait_write(smbus); + if (status) + return status; outb(AMD_EC_CMD_WR, smbus->base + AMD_EC_CMD); - if (amd_ec_wait_write(smbus)) - return -1; + status = amd_ec_wait_write(smbus); + if (status) + return status; outb(address, smbus->base + AMD_EC_DATA); - if (amd_ec_wait_write(smbus)) - return -1; + status = amd_ec_wait_write(smbus); + if (status) + return status; outb(data, smbus->base + AMD_EC_DATA); return 0; @@ -267,12 +278,17 @@ static s32 amd8111_access(struct i2c_adapter * adap, u16 addr, default: dev_warn(&adap->dev, "Unsupported transaction %d\n", size); - return -1; + return -EOPNOTSUPP; } amd_ec_write(smbus, AMD_SMB_ADDR, addr << 1); amd_ec_write(smbus, AMD_SMB_PRTCL, protocol); + /* FIXME this discards status from ec_read(); so temp[0] will + * hold stack garbage ... the rest of this routine will act + * nonsensically. Ignored ec_write() status might explain + * some such failures... + */ amd_ec_read(smbus, AMD_SMB_STS, temp + 0); if (~temp[0] & AMD_SMB_STS_DONE) { @@ -286,7 +302,7 @@ static s32 amd8111_access(struct i2c_adapter * adap, u16 addr, } if ((~temp[0] & AMD_SMB_STS_DONE) || (temp[0] & AMD_SMB_STS_STATUS)) - return -1; + return -EIO; if (read_write == I2C_SMBUS_WRITE) return 0; @@ -359,6 +375,10 @@ static int __devinit amd8111_probe(struct pci_dev *dev, smbus->base = pci_resource_start(dev, 0); smbus->size = pci_resource_len(dev, 0); + error = acpi_check_resource_conflict(&dev->resource[0]); + if (error) + goto out_kfree; + if (!request_region(smbus->base, smbus->size, amd8111_driver.name)) { error = -EBUSY; goto out_kfree; @@ -368,7 +388,7 @@ static int __devinit amd8111_probe(struct pci_dev *dev, snprintf(smbus->adapter.name, sizeof(smbus->adapter.name), "SMBus2 AMD8111 adapter at %04x", smbus->base); smbus->adapter.id = I2C_HW_SMBUS_AMD8111; - smbus->adapter.class = I2C_CLASS_HWMON; + smbus->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD; smbus->adapter.algo = &smbus_algorithm; smbus->adapter.algo_data = smbus; diff --git a/drivers/i2c/busses/i2c-au1550.c b/drivers/i2c/busses/i2c-au1550.c index cae9dc89d88c..66a04c2c660f 100644 --- a/drivers/i2c/busses/i2c-au1550.c +++ b/drivers/i2c/busses/i2c-au1550.c @@ -269,9 +269,13 @@ static int au1550_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg *msgs, int num) { struct i2c_au1550_data *adap = i2c_adap->algo_data; + volatile psc_smb_t *sp = (volatile psc_smb_t *)adap->psc_base; struct i2c_msg *p; int i, err = 0; + sp->psc_ctrl = PSC_CTRL_ENABLE; + au_sync(); + for (i = 0; !err && i < num; i++) { p = &msgs[i]; err = do_address(adap, p->addr, p->flags & I2C_M_RD, @@ -288,6 +292,10 @@ au1550_xfer(struct i2c_adapter *i2c_adap, struct i2c_msg *msgs, int num) */ if (err == 0) err = num; + + sp->psc_ctrl = PSC_CTRL_SUSPEND; + au_sync(); + return err; } @@ -302,6 +310,61 @@ static const struct i2c_algorithm au1550_algo = { .functionality = au1550_func, }; +static void i2c_au1550_setup(struct i2c_au1550_data *priv) +{ + volatile psc_smb_t *sp = (volatile psc_smb_t *)priv->psc_base; + u32 stat; + + sp->psc_ctrl = PSC_CTRL_DISABLE; + au_sync(); + sp->psc_sel = PSC_SEL_PS_SMBUSMODE; + sp->psc_smbcfg = 0; + au_sync(); + sp->psc_ctrl = PSC_CTRL_ENABLE; + au_sync(); + do { + stat = sp->psc_smbstat; + au_sync(); + } while ((stat & PSC_SMBSTAT_SR) == 0); + + sp->psc_smbcfg = (PSC_SMBCFG_RT_FIFO8 | PSC_SMBCFG_TT_FIFO8 | + PSC_SMBCFG_DD_DISABLE); + + /* Divide by 8 to get a 6.25 MHz clock. The later protocol + * timings are based on this clock. + */ + sp->psc_smbcfg |= PSC_SMBCFG_SET_DIV(PSC_SMBCFG_DIV8); + sp->psc_smbmsk = PSC_SMBMSK_ALLMASK; + au_sync(); + + /* Set the protocol timer values. See Table 71 in the + * Au1550 Data Book for standard timing values. + */ + sp->psc_smbtmr = PSC_SMBTMR_SET_TH(0) | PSC_SMBTMR_SET_PS(15) | \ + PSC_SMBTMR_SET_PU(15) | PSC_SMBTMR_SET_SH(15) | \ + PSC_SMBTMR_SET_SU(15) | PSC_SMBTMR_SET_CL(15) | \ + PSC_SMBTMR_SET_CH(15); + au_sync(); + + sp->psc_smbcfg |= PSC_SMBCFG_DE_ENABLE; + do { + stat = sp->psc_smbstat; + au_sync(); + } while ((stat & PSC_SMBSTAT_SR) == 0); + + sp->psc_ctrl = PSC_CTRL_SUSPEND; + au_sync(); +} + +static void i2c_au1550_disable(struct i2c_au1550_data *priv) +{ + volatile psc_smb_t *sp = (volatile psc_smb_t *)priv->psc_base; + + sp->psc_smbcfg = 0; + sp->psc_ctrl = PSC_CTRL_DISABLE; + au_sync(); +} + /* * registering functions to load algorithms at runtime * Prior to calling us, the 50MHz clock frequency and routing @@ -311,9 +374,7 @@ static int __devinit i2c_au1550_probe(struct platform_device *pdev) { struct i2c_au1550_data *priv; - volatile psc_smb_t *sp; struct resource *r; - u32 stat; int ret; r = platform_get_resource(pdev, IORESOURCE_MEM, 0); @@ -348,43 +409,7 @@ i2c_au1550_probe(struct platform_device *pdev) /* Now, set up the PSC for SMBus PIO mode. */ - sp = (volatile psc_smb_t *)priv->psc_base; - sp->psc_ctrl = PSC_CTRL_DISABLE; - au_sync(); - sp->psc_sel = PSC_SEL_PS_SMBUSMODE; - sp->psc_smbcfg = 0; - au_sync(); - sp->psc_ctrl = PSC_CTRL_ENABLE; - au_sync(); - do { - stat = sp->psc_smbstat; - au_sync(); - } while ((stat & PSC_SMBSTAT_SR) == 0); - - sp->psc_smbcfg = (PSC_SMBCFG_RT_FIFO8 | PSC_SMBCFG_TT_FIFO8 | - PSC_SMBCFG_DD_DISABLE); - - /* Divide by 8 to get a 6.25 MHz clock. The later protocol - * timings are based on this clock. - */ - sp->psc_smbcfg |= PSC_SMBCFG_SET_DIV(PSC_SMBCFG_DIV8); - sp->psc_smbmsk = PSC_SMBMSK_ALLMASK; - au_sync(); - - /* Set the protocol timer values. See Table 71 in the - * Au1550 Data Book for standard timing values. - */ - sp->psc_smbtmr = PSC_SMBTMR_SET_TH(0) | PSC_SMBTMR_SET_PS(15) | \ - PSC_SMBTMR_SET_PU(15) | PSC_SMBTMR_SET_SH(15) | \ - PSC_SMBTMR_SET_SU(15) | PSC_SMBTMR_SET_CL(15) | \ - PSC_SMBTMR_SET_CH(15); - au_sync(); - - sp->psc_smbcfg |= PSC_SMBCFG_DE_ENABLE; - do { - stat = sp->psc_smbstat; - au_sync(); - } while ((stat & PSC_SMBSTAT_DR) == 0); + i2c_au1550_setup(priv); ret = i2c_add_numbered_adapter(&priv->adap); if (ret == 0) { @@ -392,10 +417,7 @@ i2c_au1550_probe(struct platform_device *pdev) return 0; } - /* disable the PSC */ - sp->psc_smbcfg = 0; - sp->psc_ctrl = PSC_CTRL_DISABLE; - au_sync(); + i2c_au1550_disable(priv); release_resource(priv->ioarea); kfree(priv->ioarea); @@ -409,27 +431,24 @@ static int __devexit i2c_au1550_remove(struct platform_device *pdev) { struct i2c_au1550_data *priv = platform_get_drvdata(pdev); - volatile psc_smb_t *sp = (volatile psc_smb_t *)priv->psc_base; platform_set_drvdata(pdev, NULL); i2c_del_adapter(&priv->adap); - sp->psc_smbcfg = 0; - sp->psc_ctrl = PSC_CTRL_DISABLE; - au_sync(); + i2c_au1550_disable(priv); release_resource(priv->ioarea); kfree(priv->ioarea); kfree(priv); return 0; } +#ifdef CONFIG_PM static int i2c_au1550_suspend(struct platform_device *pdev, pm_message_t state) { struct i2c_au1550_data *priv = platform_get_drvdata(pdev); - volatile psc_smb_t *sp = (volatile psc_smb_t *)priv->psc_base; - sp->psc_ctrl = PSC_CTRL_SUSPEND; - au_sync(); + i2c_au1550_disable(priv); + return 0; } @@ -437,14 +456,15 @@ static int i2c_au1550_resume(struct platform_device *pdev) { struct i2c_au1550_data *priv = platform_get_drvdata(pdev); - volatile psc_smb_t *sp = (volatile psc_smb_t *)priv->psc_base; - sp->psc_ctrl = PSC_CTRL_ENABLE; - au_sync(); - while (!(sp->psc_smbstat & PSC_SMBSTAT_SR)) - au_sync(); + i2c_au1550_setup(priv); + return 0; } +#else +#define i2c_au1550_suspend NULL +#define i2c_au1550_resume NULL +#endif static struct platform_driver au1xpsc_smbus_driver = { .driver = { diff --git a/drivers/i2c/busses/i2c-cpm.c b/drivers/i2c/busses/i2c-cpm.c new file mode 100644 index 000000000000..8164de1f4d72 --- /dev/null +++ b/drivers/i2c/busses/i2c-cpm.c @@ -0,0 +1,745 @@ +/* + * Freescale CPM1/CPM2 I2C interface. + * Copyright (c) 1999 Dan Malek (dmalek@jlc.net). + * + * moved into proper i2c interface; + * Brad Parker (brad@heeltoe.com) + * + * Parts from dbox2_i2c.c (cvs.tuxbox.org) + * (C) 2000-2001 Felix Domke (tmbinc@gmx.net), Gillem (htoa@gmx.net) + * + * (C) 2007 Montavista Software, Inc. + * Vitaly Bordug <vitb@kernel.crashing.org> + * + * Converted to of_platform_device. Renamed to i2c-cpm.c. + * (C) 2007,2008 Jochen Friedrich <jochen@scram.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/delay.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/errno.h> +#include <linux/stddef.h> +#include <linux/i2c.h> +#include <linux/io.h> +#include <linux/dma-mapping.h> +#include <linux/of_device.h> +#include <linux/of_platform.h> +#include <linux/of_i2c.h> +#include <sysdev/fsl_soc.h> +#include <asm/cpm.h> + +/* Try to define this if you have an older CPU (earlier than rev D4) */ +/* However, better use a GPIO based bitbang driver in this case :/ */ +#undef I2C_CHIP_ERRATA + +#define CPM_MAX_READ 513 +#define CPM_MAXBD 4 + +#define I2C_EB (0x10) /* Big endian mode */ +#define I2C_EB_CPM2 (0x30) /* Big endian mode, memory snoop */ + +#define DPRAM_BASE ((u8 __iomem __force *)cpm_muram_addr(0)) + +/* I2C parameter RAM. */ +struct i2c_ram { + ushort rbase; /* Rx Buffer descriptor base address */ + ushort tbase; /* Tx Buffer descriptor base address */ + u_char rfcr; /* Rx function code */ + u_char tfcr; /* Tx function code */ + ushort mrblr; /* Max receive buffer length */ + uint rstate; /* Internal */ + uint rdp; /* Internal */ + ushort rbptr; /* Rx Buffer descriptor pointer */ + ushort rbc; /* Internal */ + uint rxtmp; /* Internal */ + uint tstate; /* Internal */ + uint tdp; /* Internal */ + ushort tbptr; /* Tx Buffer descriptor pointer */ + ushort tbc; /* Internal */ + uint txtmp; /* Internal */ + char res1[4]; /* Reserved */ + ushort rpbase; /* Relocation pointer */ + char res2[2]; /* Reserved */ +}; + +#define I2COM_START 0x80 +#define I2COM_MASTER 0x01 +#define I2CER_TXE 0x10 +#define I2CER_BUSY 0x04 +#define I2CER_TXB 0x02 +#define I2CER_RXB 0x01 +#define I2MOD_EN 0x01 + +/* I2C Registers */ +struct i2c_reg { + u8 i2mod; + u8 res1[3]; + u8 i2add; + u8 res2[3]; + u8 i2brg; + u8 res3[3]; + u8 i2com; + u8 res4[3]; + u8 i2cer; + u8 res5[3]; + u8 i2cmr; +}; + +struct cpm_i2c { + char *base; + struct of_device *ofdev; + struct i2c_adapter adap; + uint dp_addr; + int version; /* CPM1=1, CPM2=2 */ + int irq; + int cp_command; + int freq; + struct i2c_reg __iomem *i2c_reg; + struct i2c_ram __iomem *i2c_ram; + u16 i2c_addr; + wait_queue_head_t i2c_wait; + cbd_t __iomem *tbase; + cbd_t __iomem *rbase; + u_char *txbuf[CPM_MAXBD]; + u_char *rxbuf[CPM_MAXBD]; + u32 txdma[CPM_MAXBD]; + u32 rxdma[CPM_MAXBD]; +}; + +static irqreturn_t cpm_i2c_interrupt(int irq, void *dev_id) +{ + struct cpm_i2c *cpm; + struct i2c_reg __iomem *i2c_reg; + struct i2c_adapter *adap = dev_id; + int i; + + cpm = i2c_get_adapdata(dev_id); + i2c_reg = cpm->i2c_reg; + + /* Clear interrupt. */ + i = in_8(&i2c_reg->i2cer); + out_8(&i2c_reg->i2cer, i); + + dev_dbg(&adap->dev, "Interrupt: %x\n", i); + + wake_up_interruptible(&cpm->i2c_wait); + + return i ? IRQ_HANDLED : IRQ_NONE; +} + +static void cpm_reset_i2c_params(struct cpm_i2c *cpm) +{ + struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram; + + /* Set up the I2C parameters in the parameter ram. */ + out_be16(&i2c_ram->tbase, (u8 __iomem *)cpm->tbase - DPRAM_BASE); + out_be16(&i2c_ram->rbase, (u8 __iomem *)cpm->rbase - DPRAM_BASE); + + if (cpm->version == 1) { + out_8(&i2c_ram->tfcr, I2C_EB); + out_8(&i2c_ram->rfcr, I2C_EB); + } else { + out_8(&i2c_ram->tfcr, I2C_EB_CPM2); + out_8(&i2c_ram->rfcr, I2C_EB_CPM2); + } + + out_be16(&i2c_ram->mrblr, CPM_MAX_READ); + + out_be32(&i2c_ram->rstate, 0); + out_be32(&i2c_ram->rdp, 0); + out_be16(&i2c_ram->rbptr, 0); + out_be16(&i2c_ram->rbc, 0); + out_be32(&i2c_ram->rxtmp, 0); + out_be32(&i2c_ram->tstate, 0); + out_be32(&i2c_ram->tdp, 0); + out_be16(&i2c_ram->tbptr, 0); + out_be16(&i2c_ram->tbc, 0); + out_be32(&i2c_ram->txtmp, 0); +} + +static void cpm_i2c_force_close(struct i2c_adapter *adap) +{ + struct cpm_i2c *cpm = i2c_get_adapdata(adap); + struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg; + + dev_dbg(&adap->dev, "cpm_i2c_force_close()\n"); + + cpm_command(cpm->cp_command, CPM_CR_CLOSE_RX_BD); + + out_8(&i2c_reg->i2cmr, 0x00); /* Disable all interrupts */ + out_8(&i2c_reg->i2cer, 0xff); +} + +static void cpm_i2c_parse_message(struct i2c_adapter *adap, + struct i2c_msg *pmsg, int num, int tx, int rx) +{ + cbd_t __iomem *tbdf; + cbd_t __iomem *rbdf; + u_char addr; + u_char *tb; + u_char *rb; + struct cpm_i2c *cpm = i2c_get_adapdata(adap); + + tbdf = cpm->tbase + tx; + rbdf = cpm->rbase + rx; + + addr = pmsg->addr << 1; + if (pmsg->flags & I2C_M_RD) + addr |= 1; + + tb = cpm->txbuf[tx]; + rb = cpm->rxbuf[rx]; + + /* Align read buffer */ + rb = (u_char *) (((ulong) rb + 1) & ~1); + + tb[0] = addr; /* Device address byte w/rw flag */ + + out_be16(&tbdf->cbd_datlen, pmsg->len + 1); + out_be16(&tbdf->cbd_sc, 0); + + if (!(pmsg->flags & I2C_M_NOSTART)) + setbits16(&tbdf->cbd_sc, BD_I2C_START); + + if (tx + 1 == num) + setbits16(&tbdf->cbd_sc, BD_SC_LAST | BD_SC_WRAP); + + if (pmsg->flags & I2C_M_RD) { + /* + * To read, we need an empty buffer of the proper length. + * All that is used is the first byte for address, the remainder + * is just used for timing (and doesn't really have to exist). + */ + + dev_dbg(&adap->dev, "cpm_i2c_read(abyte=0x%x)\n", addr); + + out_be16(&rbdf->cbd_datlen, 0); + out_be16(&rbdf->cbd_sc, BD_SC_EMPTY | BD_SC_INTRPT); + + if (rx + 1 == CPM_MAXBD) + setbits16(&rbdf->cbd_sc, BD_SC_WRAP); + + eieio(); + setbits16(&tbdf->cbd_sc, BD_SC_READY); + } else { + dev_dbg(&adap->dev, "cpm_i2c_write(abyte=0x%x)\n", addr); + + memcpy(tb+1, pmsg->buf, pmsg->len); + + eieio(); + setbits16(&tbdf->cbd_sc, BD_SC_READY | BD_SC_INTRPT); + } +} + +static int cpm_i2c_check_message(struct i2c_adapter *adap, + struct i2c_msg *pmsg, int tx, int rx) +{ + cbd_t __iomem *tbdf; + cbd_t __iomem *rbdf; + u_char *tb; + u_char *rb; + struct cpm_i2c *cpm = i2c_get_adapdata(adap); + + tbdf = cpm->tbase + tx; + rbdf = cpm->rbase + rx; + + tb = cpm->txbuf[tx]; + rb = cpm->rxbuf[rx]; + + /* Align read buffer */ + rb = (u_char *) (((uint) rb + 1) & ~1); + + eieio(); + if (pmsg->flags & I2C_M_RD) { + dev_dbg(&adap->dev, "tx sc 0x%04x, rx sc 0x%04x\n", + in_be16(&tbdf->cbd_sc), in_be16(&rbdf->cbd_sc)); + + if (in_be16(&tbdf->cbd_sc) & BD_SC_NAK) { + dev_dbg(&adap->dev, "I2C read; No ack\n"); + return -ENXIO; + } + if (in_be16(&rbdf->cbd_sc) & BD_SC_EMPTY) { + dev_err(&adap->dev, + "I2C read; complete but rbuf empty\n"); + return -EREMOTEIO; + } + if (in_be16(&rbdf->cbd_sc) & BD_SC_OV) { + dev_err(&adap->dev, "I2C read; Overrun\n"); + return -EREMOTEIO; + } + memcpy(pmsg->buf, rb, pmsg->len); + } else { + dev_dbg(&adap->dev, "tx sc %d 0x%04x\n", tx, + in_be16(&tbdf->cbd_sc)); + + if (in_be16(&tbdf->cbd_sc) & BD_SC_NAK) { + dev_dbg(&adap->dev, "I2C write; No ack\n"); + return -ENXIO; + } + if (in_be16(&tbdf->cbd_sc) & BD_SC_UN) { + dev_err(&adap->dev, "I2C write; Underrun\n"); + return -EIO; + } + if (in_be16(&tbdf->cbd_sc) & BD_SC_CL) { + dev_err(&adap->dev, "I2C write; Collision\n"); + return -EIO; + } + } + return 0; +} + +static int cpm_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) +{ + struct cpm_i2c *cpm = i2c_get_adapdata(adap); + struct i2c_reg __iomem *i2c_reg = cpm->i2c_reg; + struct i2c_ram __iomem *i2c_ram = cpm->i2c_ram; + struct i2c_msg *pmsg; + int ret, i; + int tptr; + int rptr; + cbd_t __iomem *tbdf; + cbd_t __iomem *rbdf; + + if (num > CPM_MAXBD) + return -EINVAL; + + /* Check if we have any oversized READ requests */ + for (i = 0; i < num; i++) { + pmsg = &msgs[i]; + if (pmsg->len >= CPM_MAX_READ) + return -EINVAL; + } + + /* Reset to use first buffer */ + out_be16(&i2c_ram->rbptr, in_be16(&i2c_ram->rbase)); + out_be16(&i2c_ram->tbptr, in_be16(&i2c_ram->tbase)); + + tbdf = cpm->tbase; + rbdf = cpm->rbase; + + tptr = 0; + rptr = 0; + + while (tptr < num) { + pmsg = &msgs[tptr]; + dev_dbg(&adap->dev, "R: %d T: %d\n", rptr, tptr); + + cpm_i2c_parse_message(adap, pmsg, num, tptr, rptr); + if (pmsg->flags & I2C_M_RD) + rptr++; + tptr++; + } + /* Start transfer now */ + /* Enable RX/TX/Error interupts */ + out_8(&i2c_reg->i2cmr, I2CER_TXE | I2CER_TXB | I2CER_RXB); + out_8(&i2c_reg->i2cer, 0xff); /* Clear interrupt status */ + /* Chip bug, set enable here */ + setbits8(&i2c_reg->i2mod, I2MOD_EN); /* Enable */ + /* Begin transmission */ + setbits8(&i2c_reg->i2com, I2COM_START); + + tptr = 0; + rptr = 0; + + while (tptr < num) { + /* Check for outstanding messages */ + dev_dbg(&adap->dev, "test ready.\n"); + pmsg = &msgs[tptr]; + if (pmsg->flags & I2C_M_RD) + ret = wait_event_interruptible_timeout(cpm->i2c_wait, + !(in_be16(&rbdf[rptr].cbd_sc) & BD_SC_EMPTY), + 1 * HZ); + else + ret = wait_event_interruptible_timeout(cpm->i2c_wait, + !(in_be16(&tbdf[tptr].cbd_sc) & BD_SC_READY), + 1 * HZ); + if (ret == 0) { + ret = -EREMOTEIO; + dev_err(&adap->dev, "I2C transfer: timeout\n"); + goto out_err; + } + if (ret > 0) { + dev_dbg(&adap->dev, "ready.\n"); + ret = cpm_i2c_check_message(adap, pmsg, tptr, rptr); + tptr++; + if (pmsg->flags & I2C_M_RD) + rptr++; + if (ret) + goto out_err; + } + } +#ifdef I2C_CHIP_ERRATA + /* + * Chip errata, clear enable. This is not needed on rev D4 CPUs. + * Disabling I2C too early may cause too short stop condition + */ + udelay(4); + clrbits8(&i2c_reg->i2mod, I2MOD_EN); +#endif + return (num); + +out_err: + cpm_i2c_force_close(adap); +#ifdef I2C_CHIP_ERRATA + /* + * Chip errata, clear enable. This is not needed on rev D4 CPUs. + */ + clrbits8(&i2c_reg->i2mod, I2MOD_EN); +#endif + return ret; +} + +static u32 cpm_i2c_func(struct i2c_adapter *adap) +{ + return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK); +} + +/* -----exported algorithm data: ------------------------------------- */ + +static const struct i2c_algorithm cpm_i2c_algo = { + .master_xfer = cpm_i2c_xfer, + .functionality = cpm_i2c_func, +}; + +static const struct i2c_adapter cpm_ops = { + .owner = THIS_MODULE, + .name = "i2c-cpm", + .algo = &cpm_i2c_algo, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, +}; + +static int __devinit cpm_i2c_setup(struct cpm_i2c *cpm) +{ + struct of_device *ofdev = cpm->ofdev; + const u32 *data; + int len, ret, i; + void __iomem *i2c_base; + cbd_t __iomem *tbdf; + cbd_t __iomem *rbdf; + unsigned char brg; + + dev_dbg(&cpm->ofdev->dev, "cpm_i2c_setup()\n"); + + init_waitqueue_head(&cpm->i2c_wait); + + cpm->irq = of_irq_to_resource(ofdev->node, 0, NULL); + if (cpm->irq == NO_IRQ) + return -EINVAL; + + /* Install interrupt handler. */ + ret = request_irq(cpm->irq, cpm_i2c_interrupt, 0, "cpm_i2c", + &cpm->adap); + if (ret) + return ret; + + /* I2C parameter RAM */ + i2c_base = of_iomap(ofdev->node, 1); + if (i2c_base == NULL) { + ret = -EINVAL; + goto out_irq; + } + + if (of_device_is_compatible(ofdev->node, "fsl,cpm1-i2c")) { + + /* Check for and use a microcode relocation patch. */ + cpm->i2c_ram = i2c_base; + cpm->i2c_addr = in_be16(&cpm->i2c_ram->rpbase); + + /* + * Maybe should use cpm_muram_alloc instead of hardcoding + * this in micropatch.c + */ + if (cpm->i2c_addr) { + cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr); + iounmap(i2c_base); + } + + cpm->version = 1; + + } else if (of_device_is_compatible(ofdev->node, "fsl,cpm2-i2c")) { + cpm->i2c_addr = cpm_muram_alloc(sizeof(struct i2c_ram), 64); + cpm->i2c_ram = cpm_muram_addr(cpm->i2c_addr); + out_be16(i2c_base, cpm->i2c_addr); + iounmap(i2c_base); + + cpm->version = 2; + + } else { + iounmap(i2c_base); + ret = -EINVAL; + goto out_irq; + } + + /* I2C control/status registers */ + cpm->i2c_reg = of_iomap(ofdev->node, 0); + if (cpm->i2c_reg == NULL) { + ret = -EINVAL; + goto out_ram; + } + + data = of_get_property(ofdev->node, "fsl,cpm-command", &len); + if (!data || len != 4) { + ret = -EINVAL; + goto out_reg; + } + cpm->cp_command = *data; + + data = of_get_property(ofdev->node, "linux,i2c-class", &len); + if (data && len == 4) + cpm->adap.class = *data; + + data = of_get_property(ofdev->node, "clock-frequency", &len); + if (data && len == 4) + cpm->freq = *data; + else + cpm->freq = 60000; /* use 60kHz i2c clock by default */ + + /* + * Allocate space for CPM_MAXBD transmit and receive buffer + * descriptors in the DP ram. + */ + cpm->dp_addr = cpm_muram_alloc(sizeof(cbd_t) * 2 * CPM_MAXBD, 8); + if (!cpm->dp_addr) { + ret = -ENOMEM; + goto out_reg; + } + + cpm->tbase = cpm_muram_addr(cpm->dp_addr); + cpm->rbase = cpm_muram_addr(cpm->dp_addr + sizeof(cbd_t) * CPM_MAXBD); + + /* Allocate TX and RX buffers */ + + tbdf = cpm->tbase; + rbdf = cpm->rbase; + + for (i = 0; i < CPM_MAXBD; i++) { + cpm->rxbuf[i] = dma_alloc_coherent( + NULL, CPM_MAX_READ + 1, &cpm->rxdma[i], GFP_KERNEL); + if (!cpm->rxbuf[i]) { + ret = -ENOMEM; + goto out_muram; + } + out_be32(&rbdf[i].cbd_bufaddr, ((cpm->rxdma[i] + 1) & ~1)); + + cpm->txbuf[i] = (unsigned char *)dma_alloc_coherent( + NULL, CPM_MAX_READ + 1, &cpm->txdma[i], GFP_KERNEL); + if (!cpm->txbuf[i]) { + ret = -ENOMEM; + goto out_muram; + } + out_be32(&tbdf[i].cbd_bufaddr, cpm->txdma[i]); + } + + /* Initialize Tx/Rx parameters. */ + + cpm_reset_i2c_params(cpm); + + dev_dbg(&cpm->ofdev->dev, "i2c_ram 0x%p, i2c_addr 0x%04x, freq %d\n", + cpm->i2c_ram, cpm->i2c_addr, cpm->freq); + dev_dbg(&cpm->ofdev->dev, "tbase 0x%04x, rbase 0x%04x\n", + (u8 __iomem *)cpm->tbase - DPRAM_BASE, + (u8 __iomem *)cpm->rbase - DPRAM_BASE); + + cpm_command(cpm->cp_command, CPM_CR_INIT_TRX); + + /* + * Select an invalid address. Just make sure we don't use loopback mode + */ + out_8(&cpm->i2c_reg->i2add, 0x7f << 1); + + /* + * PDIV is set to 00 in i2mod, so brgclk/32 is used as input to the + * i2c baud rate generator. This is divided by 2 x (DIV + 3) to get + * the actual i2c bus frequency. + */ + brg = get_brgfreq() / (32 * 2 * cpm->freq) - 3; + out_8(&cpm->i2c_reg->i2brg, brg); + + out_8(&cpm->i2c_reg->i2mod, 0x00); + out_8(&cpm->i2c_reg->i2com, I2COM_MASTER); /* Master mode */ + + /* Disable interrupts. */ + out_8(&cpm->i2c_reg->i2cmr, 0); + out_8(&cpm->i2c_reg->i2cer, 0xff); + + return 0; + +out_muram: + for (i = 0; i < CPM_MAXBD; i++) { + if (cpm->rxbuf[i]) + dma_free_coherent(NULL, CPM_MAX_READ + 1, + cpm->rxbuf[i], cpm->rxdma[i]); + if (cpm->txbuf[i]) + dma_free_coherent(NULL, CPM_MAX_READ + 1, + cpm->txbuf[i], cpm->txdma[i]); + } + cpm_muram_free(cpm->dp_addr); +out_reg: + iounmap(cpm->i2c_reg); +out_ram: + if ((cpm->version == 1) && (!cpm->i2c_addr)) + iounmap(cpm->i2c_ram); + if (cpm->version == 2) + cpm_muram_free(cpm->i2c_addr); +out_irq: + free_irq(cpm->irq, &cpm->adap); + return ret; +} + +static void cpm_i2c_shutdown(struct cpm_i2c *cpm) +{ + int i; + + /* Shut down I2C. */ + clrbits8(&cpm->i2c_reg->i2mod, I2MOD_EN); + + /* Disable interrupts */ + out_8(&cpm->i2c_reg->i2cmr, 0); + out_8(&cpm->i2c_reg->i2cer, 0xff); + + free_irq(cpm->irq, &cpm->adap); + + /* Free all memory */ + for (i = 0; i < CPM_MAXBD; i++) { + dma_free_coherent(NULL, CPM_MAX_READ + 1, + cpm->rxbuf[i], cpm->rxdma[i]); + dma_free_coherent(NULL, CPM_MAX_READ + 1, + cpm->txbuf[i], cpm->txdma[i]); + } + + cpm_muram_free(cpm->dp_addr); + iounmap(cpm->i2c_reg); + + if ((cpm->version == 1) && (!cpm->i2c_addr)) + iounmap(cpm->i2c_ram); + if (cpm->version == 2) + cpm_muram_free(cpm->i2c_addr); +} + +static int __devinit cpm_i2c_probe(struct of_device *ofdev, + const struct of_device_id *match) +{ + int result, len; + struct cpm_i2c *cpm; + const u32 *data; + + cpm = kzalloc(sizeof(struct cpm_i2c), GFP_KERNEL); + if (!cpm) + return -ENOMEM; + + cpm->ofdev = ofdev; + + dev_set_drvdata(&ofdev->dev, cpm); + + cpm->adap = cpm_ops; + i2c_set_adapdata(&cpm->adap, cpm); + cpm->adap.dev.parent = &ofdev->dev; + + result = cpm_i2c_setup(cpm); + if (result) { + dev_err(&ofdev->dev, "Unable to init hardware\n"); + goto out_free; + } + + /* register new adapter to i2c module... */ + + data = of_get_property(ofdev->node, "linux,i2c-index", &len); + if (data && len == 4) { + cpm->adap.nr = *data; + result = i2c_add_numbered_adapter(&cpm->adap); + } else + result = i2c_add_adapter(&cpm->adap); + + if (result < 0) { + dev_err(&ofdev->dev, "Unable to register with I2C\n"); + goto out_shut; + } + + dev_dbg(&ofdev->dev, "hw routines for %s registered.\n", + cpm->adap.name); + + /* + * register OF I2C devices + */ + of_register_i2c_devices(&cpm->adap, ofdev->node); + + return 0; +out_shut: + cpm_i2c_shutdown(cpm); +out_free: + dev_set_drvdata(&ofdev->dev, NULL); + kfree(cpm); + + return result; +} + +static int __devexit cpm_i2c_remove(struct of_device *ofdev) +{ + struct cpm_i2c *cpm = dev_get_drvdata(&ofdev->dev); + + i2c_del_adapter(&cpm->adap); + + cpm_i2c_shutdown(cpm); + + dev_set_drvdata(&ofdev->dev, NULL); + kfree(cpm); + + return 0; +} + +static const struct of_device_id cpm_i2c_match[] = { + { + .compatible = "fsl,cpm1-i2c", + }, + { + .compatible = "fsl,cpm2-i2c", + }, + {}, +}; + +MODULE_DEVICE_TABLE(of, cpm_i2c_match); + +static struct of_platform_driver cpm_i2c_driver = { + .match_table = cpm_i2c_match, + .probe = cpm_i2c_probe, + .remove = __devexit_p(cpm_i2c_remove), + .driver = { + .name = "fsl-i2c-cpm", + .owner = THIS_MODULE, + } +}; + +static int __init cpm_i2c_init(void) +{ + return of_register_platform_driver(&cpm_i2c_driver); +} + +static void __exit cpm_i2c_exit(void) +{ + of_unregister_platform_driver(&cpm_i2c_driver); +} + +module_init(cpm_i2c_init); +module_exit(cpm_i2c_exit); + +MODULE_AUTHOR("Jochen Friedrich <jochen@scram.de>"); +MODULE_DESCRIPTION("I2C-Bus adapter routines for CPM boards"); +MODULE_LICENSE("GPL"); diff --git a/drivers/i2c/busses/i2c-davinci.c b/drivers/i2c/busses/i2c-davinci.c index 7ecbfc429b19..af3846eda985 100644 --- a/drivers/i2c/busses/i2c-davinci.c +++ b/drivers/i2c/busses/i2c-davinci.c @@ -85,6 +85,7 @@ #define DAVINCI_I2C_MDR_MST (1 << 10) #define DAVINCI_I2C_MDR_TRX (1 << 9) #define DAVINCI_I2C_MDR_XA (1 << 8) +#define DAVINCI_I2C_MDR_RM (1 << 7) #define DAVINCI_I2C_MDR_IRS (1 << 5) #define DAVINCI_I2C_IMR_AAS (1 << 6) @@ -112,6 +113,7 @@ struct davinci_i2c_dev { u8 *buf; size_t buf_len; int irq; + u8 terminate; struct i2c_adapter adapter; }; @@ -142,6 +144,7 @@ static int i2c_davinci_init(struct davinci_i2c_dev *dev) struct davinci_i2c_platform_data *pdata = dev->dev->platform_data; u16 psc; u32 clk; + u32 d; u32 clkh; u32 clkl; u32 input_clock = clk_get_rate(dev->clk); @@ -171,23 +174,29 @@ static int i2c_davinci_init(struct davinci_i2c_dev *dev) * if PSC > 1 , d = 5 */ - psc = 26; /* To get 1MHz clock */ + /* get minimum of 7 MHz clock, but max of 12 MHz */ + psc = (input_clock / 7000000) - 1; + if ((input_clock / (psc + 1)) > 12000000) + psc++; /* better to run under spec than over */ + d = (psc >= 2) ? 5 : 7 - psc; - clk = ((input_clock / (psc + 1)) / (pdata->bus_freq * 1000)) - 10; - clkh = (50 * clk) / 100; + clk = ((input_clock / (psc + 1)) / (pdata->bus_freq * 1000)) - (d << 1); + clkh = clk >> 1; clkl = clk - clkh; davinci_i2c_write_reg(dev, DAVINCI_I2C_PSC_REG, psc); davinci_i2c_write_reg(dev, DAVINCI_I2C_CLKH_REG, clkh); davinci_i2c_write_reg(dev, DAVINCI_I2C_CLKL_REG, clkl); - dev_dbg(dev->dev, "CLK = %d\n", clk); + dev_dbg(dev->dev, "input_clock = %d, CLK = %d\n", input_clock, clk); dev_dbg(dev->dev, "PSC = %d\n", davinci_i2c_read_reg(dev, DAVINCI_I2C_PSC_REG)); dev_dbg(dev->dev, "CLKL = %d\n", davinci_i2c_read_reg(dev, DAVINCI_I2C_CLKL_REG)); dev_dbg(dev->dev, "CLKH = %d\n", davinci_i2c_read_reg(dev, DAVINCI_I2C_CLKH_REG)); + dev_dbg(dev->dev, "bus_freq = %dkHz, bus_delay = %d\n", + pdata->bus_freq, pdata->bus_delay); /* Take the I2C module out of reset: */ w = davinci_i2c_read_reg(dev, DAVINCI_I2C_MDR_REG); @@ -233,7 +242,6 @@ i2c_davinci_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg, int stop) struct davinci_i2c_dev *dev = i2c_get_adapdata(adap); struct davinci_i2c_platform_data *pdata = dev->dev->platform_data; u32 flag; - u32 stat; u16 w; int r; @@ -254,12 +262,9 @@ i2c_davinci_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg, int stop) davinci_i2c_write_reg(dev, DAVINCI_I2C_CNT_REG, dev->buf_len); - init_completion(&dev->cmd_complete); + INIT_COMPLETION(dev->cmd_complete); dev->cmd_err = 0; - /* Clear any pending interrupts by reading the IVR */ - stat = davinci_i2c_read_reg(dev, DAVINCI_I2C_IVR_REG); - /* Take I2C out of reset, configure it as master and set the * start bit */ flag = DAVINCI_I2C_MDR_IRS | DAVINCI_I2C_MDR_MST | DAVINCI_I2C_MDR_STT; @@ -280,20 +285,34 @@ i2c_davinci_xfer_msg(struct i2c_adapter *adap, struct i2c_msg *msg, int stop) MOD_REG_BIT(w, DAVINCI_I2C_IMR_XRDY, 1); davinci_i2c_write_reg(dev, DAVINCI_I2C_IMR_REG, w); + dev->terminate = 0; /* write the data into mode register */ davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, flag); r = wait_for_completion_interruptible_timeout(&dev->cmd_complete, DAVINCI_I2C_TIMEOUT); - dev->buf_len = 0; - if (r < 0) - return r; - if (r == 0) { dev_err(dev->dev, "controller timed out\n"); i2c_davinci_init(dev); + dev->buf_len = 0; return -ETIMEDOUT; } + if (dev->buf_len) { + /* This should be 0 if all bytes were transferred + * or dev->cmd_err denotes an error. + * A signal may have aborted the transfer. + */ + if (r >= 0) { + dev_err(dev->dev, "abnormal termination buf_len=%i\n", + dev->buf_len); + r = -EREMOTEIO; + } + dev->terminate = 1; + wmb(); + dev->buf_len = 0; + } + if (r < 0) + return r; /* no error */ if (likely(!dev->cmd_err)) @@ -338,12 +357,11 @@ i2c_davinci_xfer(struct i2c_adapter *adap, struct i2c_msg msgs[], int num) for (i = 0; i < num; i++) { ret = i2c_davinci_xfer_msg(adap, &msgs[i], (i == (num - 1))); + dev_dbg(dev->dev, "%s [%d/%d] ret: %d\n", __func__, i + 1, num, + ret); if (ret < 0) return ret; } - - dev_dbg(dev->dev, "%s:%d ret: %d\n", __func__, __LINE__, ret); - return num; } @@ -352,6 +370,27 @@ static u32 i2c_davinci_func(struct i2c_adapter *adap) return I2C_FUNC_I2C | (I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK); } +static void terminate_read(struct davinci_i2c_dev *dev) +{ + u16 w = davinci_i2c_read_reg(dev, DAVINCI_I2C_MDR_REG); + w |= DAVINCI_I2C_MDR_NACK; + davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, w); + + /* Throw away data */ + davinci_i2c_read_reg(dev, DAVINCI_I2C_DRR_REG); + if (!dev->terminate) + dev_err(dev->dev, "RDR IRQ while no data requested\n"); +} +static void terminate_write(struct davinci_i2c_dev *dev) +{ + u16 w = davinci_i2c_read_reg(dev, DAVINCI_I2C_MDR_REG); + w |= DAVINCI_I2C_MDR_RM | DAVINCI_I2C_MDR_STP; + davinci_i2c_write_reg(dev, DAVINCI_I2C_MDR_REG, w); + + if (!dev->terminate) + dev_err(dev->dev, "TDR IRQ while no data to send\n"); +} + /* * Interrupt service routine. This gets called whenever an I2C interrupt * occurs. @@ -372,12 +411,15 @@ static irqreturn_t i2c_davinci_isr(int this_irq, void *dev_id) switch (stat) { case DAVINCI_I2C_IVR_AL: + /* Arbitration lost, must retry */ dev->cmd_err |= DAVINCI_I2C_STR_AL; + dev->buf_len = 0; complete(&dev->cmd_complete); break; case DAVINCI_I2C_IVR_NACK: dev->cmd_err |= DAVINCI_I2C_STR_NACK; + dev->buf_len = 0; complete(&dev->cmd_complete); break; @@ -399,9 +441,10 @@ static irqreturn_t i2c_davinci_isr(int this_irq, void *dev_id) davinci_i2c_write_reg(dev, DAVINCI_I2C_STR_REG, DAVINCI_I2C_IMR_RRDY); - } else - dev_err(dev->dev, "RDR IRQ while no " - "data requested\n"); + } else { + /* signal can terminate transfer */ + terminate_read(dev); + } break; case DAVINCI_I2C_IVR_XRDY: @@ -418,9 +461,10 @@ static irqreturn_t i2c_davinci_isr(int this_irq, void *dev_id) davinci_i2c_write_reg(dev, DAVINCI_I2C_IMR_REG, w); - } else - dev_err(dev->dev, "TDR IRQ while no data to " - "send\n"); + } else { + /* signal can terminate transfer */ + terminate_write(dev); + } break; case DAVINCI_I2C_IVR_SCD: @@ -475,6 +519,7 @@ static int davinci_i2c_probe(struct platform_device *pdev) goto err_release_region; } + init_completion(&dev->cmd_complete); dev->dev = get_device(&pdev->dev); dev->irq = irq->start; platform_set_drvdata(pdev, dev); diff --git a/drivers/i2c/busses/i2c-elektor.c b/drivers/i2c/busses/i2c-elektor.c index b7a9977b025f..7f38c01fb3a0 100644 --- a/drivers/i2c/busses/i2c-elektor.c +++ b/drivers/i2c/busses/i2c-elektor.c @@ -196,13 +196,11 @@ static struct i2c_algo_pcf_data pcf_isa_data = { .getown = pcf_isa_getown, .getclock = pcf_isa_getclock, .waitforpin = pcf_isa_waitforpin, - .udelay = 10, - .timeout = 100, }; static struct i2c_adapter pcf_isa_ops = { .owner = THIS_MODULE, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .id = I2C_HW_P_ELEK, .algo_data = &pcf_isa_data, .name = "i2c-elektor", diff --git a/drivers/i2c/busses/i2c-gpio.c b/drivers/i2c/busses/i2c-gpio.c index 7c1b762aa681..79b455a1f090 100644 --- a/drivers/i2c/busses/i2c-gpio.c +++ b/drivers/i2c/busses/i2c-gpio.c @@ -140,7 +140,7 @@ static int __init i2c_gpio_probe(struct platform_device *pdev) adap->owner = THIS_MODULE; snprintf(adap->name, sizeof(adap->name), "i2c-gpio%d", pdev->id); adap->algo_data = bit_data; - adap->class = I2C_CLASS_HWMON; + adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; adap->dev.parent = &pdev->dev; /* diff --git a/drivers/i2c/busses/i2c-hydra.c b/drivers/i2c/busses/i2c-hydra.c index f9972f9651e4..1098f21ace13 100644 --- a/drivers/i2c/busses/i2c-hydra.c +++ b/drivers/i2c/busses/i2c-hydra.c @@ -1,7 +1,4 @@ /* - i2c-hydra.c - Part of lm_sensors, Linux kernel modules - for hardware monitoring - i2c Support for the Apple `Hydra' Mac I/O Copyright (c) 1999-2004 Geert Uytterhoeven <geert@linux-m68k.org> diff --git a/drivers/i2c/busses/i2c-i801.c b/drivers/i2c/busses/i2c-i801.c index b0f771fe4326..dc7ea32b69a8 100644 --- a/drivers/i2c/busses/i2c-i801.c +++ b/drivers/i2c/busses/i2c-i801.c @@ -1,10 +1,8 @@ /* - i2c-i801.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring Copyright (c) 1998 - 2002 Frodo Looijaard <frodol@dds.nl>, Philip Edelbrock <phil@netroedge.com>, and Mark D. Studebaker <mdsxyz123@yahoo.com> - Copyright (C) 2007 Jean Delvare <khali@linux-fr.org> + Copyright (C) 2007, 2008 Jean Delvare <khali@linux-fr.org> This program is free software; you can redistribute it and/or modify it under the terms of the GNU General Public License as published by @@ -64,6 +62,7 @@ #include <linux/ioport.h> #include <linux/init.h> #include <linux/i2c.h> +#include <linux/acpi.h> #include <asm/io.h> /* I801 SMBus address offsets */ @@ -121,6 +120,10 @@ #define SMBHSTSTS_INTR 0x02 #define SMBHSTSTS_HOST_BUSY 0x01 +#define STATUS_FLAGS (SMBHSTSTS_BYTE_DONE | SMBHSTSTS_FAILED | \ + SMBHSTSTS_BUS_ERR | SMBHSTSTS_DEV_ERR | \ + SMBHSTSTS_INTR) + static unsigned long i801_smba; static unsigned char i801_original_hstcfg; static struct pci_driver i801_driver; @@ -132,105 +135,137 @@ static struct pci_dev *I801_dev; #define FEATURE_I2C_BLOCK_READ (1 << 3) static unsigned int i801_features; -static int i801_transaction(int xact) +/* Make sure the SMBus host is ready to start transmitting. + Return 0 if it is, -EBUSY if it is not. */ +static int i801_check_pre(void) { - int temp; - int result = 0; - int timeout = 0; + int status; - dev_dbg(&I801_dev->dev, "Transaction (pre): CNT=%02x, CMD=%02x, " - "ADD=%02x, DAT0=%02x, DAT1=%02x\n", inb_p(SMBHSTCNT), - inb_p(SMBHSTCMD), inb_p(SMBHSTADD), inb_p(SMBHSTDAT0), - inb_p(SMBHSTDAT1)); - - /* Make sure the SMBus host is ready to start transmitting */ - /* 0x1f = Failed, Bus_Err, Dev_Err, Intr, Host_Busy */ - if ((temp = (0x1f & inb_p(SMBHSTSTS))) != 0x00) { - dev_dbg(&I801_dev->dev, "SMBus busy (%02x). Resetting...\n", - temp); - outb_p(temp, SMBHSTSTS); - if ((temp = (0x1f & inb_p(SMBHSTSTS))) != 0x00) { - dev_dbg(&I801_dev->dev, "Failed! (%02x)\n", temp); - return -1; - } else { - dev_dbg(&I801_dev->dev, "Successful!\n"); + status = inb_p(SMBHSTSTS); + if (status & SMBHSTSTS_HOST_BUSY) { + dev_err(&I801_dev->dev, "SMBus is busy, can't use it!\n"); + return -EBUSY; + } + + status &= STATUS_FLAGS; + if (status) { + dev_dbg(&I801_dev->dev, "Clearing status flags (%02x)\n", + status); + outb_p(status, SMBHSTSTS); + status = inb_p(SMBHSTSTS) & STATUS_FLAGS; + if (status) { + dev_err(&I801_dev->dev, + "Failed clearing status flags (%02x)\n", + status); + return -EBUSY; } } - /* the current contents of SMBHSTCNT can be overwritten, since PEC, - * INTREN, SMBSCMD are passed in xact */ - outb_p(xact | I801_START, SMBHSTCNT); + return 0; +} - /* We will always wait for a fraction of a second! */ - do { - msleep(1); - temp = inb_p(SMBHSTSTS); - } while ((temp & SMBHSTSTS_HOST_BUSY) && (timeout++ < MAX_TIMEOUT)); +/* Convert the status register to an error code, and clear it. */ +static int i801_check_post(int status, int timeout) +{ + int result = 0; /* If the SMBus is still busy, we give up */ - if (timeout >= MAX_TIMEOUT) { - dev_dbg(&I801_dev->dev, "SMBus Timeout!\n"); - result = -1; + if (timeout) { + dev_err(&I801_dev->dev, "Transaction timeout\n"); /* try to stop the current command */ dev_dbg(&I801_dev->dev, "Terminating the current operation\n"); outb_p(inb_p(SMBHSTCNT) | SMBHSTCNT_KILL, SMBHSTCNT); msleep(1); outb_p(inb_p(SMBHSTCNT) & (~SMBHSTCNT_KILL), SMBHSTCNT); - } - if (temp & SMBHSTSTS_FAILED) { - result = -1; - dev_dbg(&I801_dev->dev, "Error: Failed bus transaction\n"); + /* Check if it worked */ + status = inb_p(SMBHSTSTS); + if ((status & SMBHSTSTS_HOST_BUSY) || + !(status & SMBHSTSTS_FAILED)) + dev_err(&I801_dev->dev, + "Failed terminating the transaction\n"); + outb_p(STATUS_FLAGS, SMBHSTSTS); + return -ETIMEDOUT; } - if (temp & SMBHSTSTS_BUS_ERR) { - result = -1; - dev_err(&I801_dev->dev, "Bus collision! SMBus may be locked " - "until next hard reset. (sorry!)\n"); - /* Clock stops and slave is stuck in mid-transmission */ + if (status & SMBHSTSTS_FAILED) { + result = -EIO; + dev_err(&I801_dev->dev, "Transaction failed\n"); } - - if (temp & SMBHSTSTS_DEV_ERR) { - result = -1; - dev_dbg(&I801_dev->dev, "Error: no response!\n"); + if (status & SMBHSTSTS_DEV_ERR) { + result = -ENXIO; + dev_dbg(&I801_dev->dev, "No response\n"); + } + if (status & SMBHSTSTS_BUS_ERR) { + result = -EAGAIN; + dev_dbg(&I801_dev->dev, "Lost arbitration\n"); } - if ((inb_p(SMBHSTSTS) & 0x1f) != 0x00) - outb_p(inb(SMBHSTSTS), SMBHSTSTS); - - if ((temp = (0x1f & inb_p(SMBHSTSTS))) != 0x00) { - dev_dbg(&I801_dev->dev, "Failed reset at end of transaction " - "(%02x)\n", temp); + if (result) { + /* Clear error flags */ + outb_p(status & STATUS_FLAGS, SMBHSTSTS); + status = inb_p(SMBHSTSTS) & STATUS_FLAGS; + if (status) { + dev_warn(&I801_dev->dev, "Failed clearing status " + "flags at end of transaction (%02x)\n", + status); + } } - dev_dbg(&I801_dev->dev, "Transaction (post): CNT=%02x, CMD=%02x, " - "ADD=%02x, DAT0=%02x, DAT1=%02x\n", inb_p(SMBHSTCNT), - inb_p(SMBHSTCMD), inb_p(SMBHSTADD), inb_p(SMBHSTDAT0), - inb_p(SMBHSTDAT1)); + return result; } +static int i801_transaction(int xact) +{ + int status; + int result; + int timeout = 0; + + result = i801_check_pre(); + if (result < 0) + return result; + + /* the current contents of SMBHSTCNT can be overwritten, since PEC, + * INTREN, SMBSCMD are passed in xact */ + outb_p(xact | I801_START, SMBHSTCNT); + + /* We will always wait for a fraction of a second! */ + do { + msleep(1); + status = inb_p(SMBHSTSTS); + } while ((status & SMBHSTSTS_HOST_BUSY) && (timeout++ < MAX_TIMEOUT)); + + result = i801_check_post(status, timeout >= MAX_TIMEOUT); + if (result < 0) + return result; + + outb_p(SMBHSTSTS_INTR, SMBHSTSTS); + return 0; +} + /* wait for INTR bit as advised by Intel */ static void i801_wait_hwpec(void) { int timeout = 0; - int temp; + int status; do { msleep(1); - temp = inb_p(SMBHSTSTS); - } while ((!(temp & SMBHSTSTS_INTR)) + status = inb_p(SMBHSTSTS); + } while ((!(status & SMBHSTSTS_INTR)) && (timeout++ < MAX_TIMEOUT)); if (timeout >= MAX_TIMEOUT) { dev_dbg(&I801_dev->dev, "PEC Timeout!\n"); } - outb_p(temp, SMBHSTSTS); + outb_p(status, SMBHSTSTS); } static int i801_block_transaction_by_block(union i2c_smbus_data *data, char read_write, int hwpec) { int i, len; + int status; inb_p(SMBHSTCNT); /* reset the data buffer index */ @@ -242,14 +277,15 @@ static int i801_block_transaction_by_block(union i2c_smbus_data *data, outb_p(data->block[i+1], SMBBLKDAT); } - if (i801_transaction(I801_BLOCK_DATA | ENABLE_INT9 | - I801_PEC_EN * hwpec)) - return -1; + status = i801_transaction(I801_BLOCK_DATA | ENABLE_INT9 | + I801_PEC_EN * hwpec); + if (status) + return status; if (read_write == I2C_SMBUS_READ) { len = inb_p(SMBHSTDAT0); if (len < 1 || len > I2C_SMBUS_BLOCK_MAX) - return -1; + return -EPROTO; data->block[0] = len; for (i = 0; i < len; i++) @@ -264,10 +300,13 @@ static int i801_block_transaction_byte_by_byte(union i2c_smbus_data *data, { int i, len; int smbcmd; - int temp; - int result = 0; + int status; + int result; int timeout; - unsigned char errmask; + + result = i801_check_pre(); + if (result < 0) + return result; len = data->block[0]; @@ -291,36 +330,6 @@ static int i801_block_transaction_byte_by_byte(union i2c_smbus_data *data, } outb_p(smbcmd | ENABLE_INT9, SMBHSTCNT); - dev_dbg(&I801_dev->dev, "Block (pre %d): CNT=%02x, CMD=%02x, " - "ADD=%02x, DAT0=%02x, DAT1=%02x, BLKDAT=%02x\n", i, - inb_p(SMBHSTCNT), inb_p(SMBHSTCMD), inb_p(SMBHSTADD), - inb_p(SMBHSTDAT0), inb_p(SMBHSTDAT1), inb_p(SMBBLKDAT)); - - /* Make sure the SMBus host is ready to start transmitting */ - temp = inb_p(SMBHSTSTS); - if (i == 1) { - /* Erroneous conditions before transaction: - * Byte_Done, Failed, Bus_Err, Dev_Err, Intr, Host_Busy */ - errmask = 0x9f; - } else { - /* Erroneous conditions during transaction: - * Failed, Bus_Err, Dev_Err, Intr */ - errmask = 0x1e; - } - if (temp & errmask) { - dev_dbg(&I801_dev->dev, "SMBus busy (%02x). " - "Resetting...\n", temp); - outb_p(temp, SMBHSTSTS); - if (((temp = inb_p(SMBHSTSTS)) & errmask) != 0x00) { - dev_err(&I801_dev->dev, - "Reset failed! (%02x)\n", temp); - return -1; - } - if (i != 1) - /* if die in middle of block transaction, fail */ - return -1; - } - if (i == 1) outb_p(inb(SMBHSTCNT) | I801_START, SMBHSTCNT); @@ -328,41 +337,28 @@ static int i801_block_transaction_byte_by_byte(union i2c_smbus_data *data, timeout = 0; do { msleep(1); - temp = inb_p(SMBHSTSTS); + status = inb_p(SMBHSTSTS); } - while ((!(temp & SMBHSTSTS_BYTE_DONE)) + while ((!(status & SMBHSTSTS_BYTE_DONE)) && (timeout++ < MAX_TIMEOUT)); - /* If the SMBus is still busy, we give up */ - if (timeout >= MAX_TIMEOUT) { - /* try to stop the current command */ - dev_dbg(&I801_dev->dev, "Terminating the current " - "operation\n"); - outb_p(inb_p(SMBHSTCNT) | SMBHSTCNT_KILL, SMBHSTCNT); - msleep(1); - outb_p(inb_p(SMBHSTCNT) & (~SMBHSTCNT_KILL), - SMBHSTCNT); - result = -1; - dev_dbg(&I801_dev->dev, "SMBus Timeout!\n"); - } - - if (temp & SMBHSTSTS_FAILED) { - result = -1; - dev_dbg(&I801_dev->dev, - "Error: Failed bus transaction\n"); - } else if (temp & SMBHSTSTS_BUS_ERR) { - result = -1; - dev_err(&I801_dev->dev, "Bus collision!\n"); - } else if (temp & SMBHSTSTS_DEV_ERR) { - result = -1; - dev_dbg(&I801_dev->dev, "Error: no response!\n"); - } + result = i801_check_post(status, timeout >= MAX_TIMEOUT); + if (result < 0) + return result; if (i == 1 && read_write == I2C_SMBUS_READ && command != I2C_SMBUS_I2C_BLOCK_DATA) { len = inb_p(SMBHSTDAT0); - if (len < 1 || len > I2C_SMBUS_BLOCK_MAX) - return -1; + if (len < 1 || len > I2C_SMBUS_BLOCK_MAX) { + dev_err(&I801_dev->dev, + "Illegal SMBus block read size %d\n", + len); + /* Recover */ + while (inb_p(SMBHSTSTS) & SMBHSTSTS_HOST_BUSY) + outb_p(SMBHSTSTS_BYTE_DONE, SMBHSTSTS); + outb_p(SMBHSTSTS_INTR, SMBHSTSTS); + return -EPROTO; + } data->block[0] = len; } @@ -371,30 +367,19 @@ static int i801_block_transaction_byte_by_byte(union i2c_smbus_data *data, data->block[i] = inb_p(SMBBLKDAT); if (read_write == I2C_SMBUS_WRITE && i+1 <= len) outb_p(data->block[i+1], SMBBLKDAT); - if ((temp & 0x9e) != 0x00) - outb_p(temp, SMBHSTSTS); /* signals SMBBLKDAT ready */ - - if ((temp = (0x1e & inb_p(SMBHSTSTS))) != 0x00) { - dev_dbg(&I801_dev->dev, - "Bad status (%02x) at end of transaction\n", - temp); - } - dev_dbg(&I801_dev->dev, "Block (post %d): CNT=%02x, CMD=%02x, " - "ADD=%02x, DAT0=%02x, DAT1=%02x, BLKDAT=%02x\n", i, - inb_p(SMBHSTCNT), inb_p(SMBHSTCMD), inb_p(SMBHSTADD), - inb_p(SMBHSTDAT0), inb_p(SMBHSTDAT1), inb_p(SMBBLKDAT)); - if (result < 0) - return result; + /* signals SMBBLKDAT ready */ + outb_p(SMBHSTSTS_BYTE_DONE | SMBHSTSTS_INTR, SMBHSTSTS); } - return result; + + return 0; } static int i801_set_block_buffer_mode(void) { outb_p(inb_p(SMBAUXCTL) | SMBAUXCTL_E32B, SMBAUXCTL); if ((inb_p(SMBAUXCTL) & SMBAUXCTL_E32B) == 0) - return -1; + return -EIO; return 0; } @@ -414,7 +399,7 @@ static int i801_block_transaction(union i2c_smbus_data *data, char read_write, } else if (!(i801_features & FEATURE_I2C_BLOCK_READ)) { dev_err(&I801_dev->dev, "I2C block read is unsupported!\n"); - return -1; + return -EOPNOTSUPP; } } @@ -449,7 +434,7 @@ static int i801_block_transaction(union i2c_smbus_data *data, char read_write, return result; } -/* Return -1 on error. */ +/* Return negative errno on error. */ static s32 i801_access(struct i2c_adapter * adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data * data) @@ -511,10 +496,9 @@ static s32 i801_access(struct i2c_adapter * adap, u16 addr, outb_p(command, SMBHSTCMD); block = 1; break; - case I2C_SMBUS_PROC_CALL: default: dev_err(&I801_dev->dev, "Unsupported transaction %d\n", size); - return -1; + return -EOPNOTSUPP; } if (hwpec) /* enable/disable hardware PEC */ @@ -537,7 +521,7 @@ static s32 i801_access(struct i2c_adapter * adap, u16 addr, if(block) return ret; if(ret) - return -1; + return ret; if ((read_write == I2C_SMBUS_WRITE) || (xact == I801_QUICK)) return 0; @@ -572,7 +556,7 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter i801_adapter = { .owner = THIS_MODULE, .id = I2C_HW_SMBUS_I801, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; @@ -639,6 +623,10 @@ static int __devinit i801_probe(struct pci_dev *dev, const struct pci_device_id goto exit; } + err = acpi_check_resource_conflict(&dev->resource[SMBBAR]); + if (err) + goto exit; + err = pci_request_region(dev, SMBBAR, i801_driver.name); if (err) { dev_err(&dev->dev, "Failed to request SMBus region " diff --git a/drivers/i2c/busses/i2c-i810.c b/drivers/i2c/busses/i2c-i810.c deleted file mode 100644 index 42e8d94c276f..000000000000 --- a/drivers/i2c/busses/i2c-i810.c +++ /dev/null @@ -1,260 +0,0 @@ -/* - i2c-i810.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring - Copyright (c) 1998, 1999, 2000 Frodo Looijaard <frodol@dds.nl>, - Philip Edelbrock <phil@netroedge.com>, - Ralph Metzler <rjkm@thp.uni-koeln.de>, and - Mark D. Studebaker <mdsxyz123@yahoo.com> - - Based on code written by Ralph Metzler <rjkm@thp.uni-koeln.de> and - Simon Vogl - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -*/ -/* - This interfaces to the I810/I815 to provide access to - the DDC Bus and the I2C Bus. - - SUPPORTED DEVICES PCI ID - i810AA 7121 - i810AB 7123 - i810E 7125 - i815 1132 - i845G 2562 -*/ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/i2c.h> -#include <linux/i2c-algo-bit.h> -#include <asm/io.h> - -/* GPIO register locations */ -#define I810_IOCONTROL_OFFSET 0x5000 -#define I810_HVSYNC 0x00 /* not used */ -#define I810_GPIOA 0x10 -#define I810_GPIOB 0x14 - -/* bit locations in the registers */ -#define SCL_DIR_MASK 0x0001 -#define SCL_DIR 0x0002 -#define SCL_VAL_MASK 0x0004 -#define SCL_VAL_OUT 0x0008 -#define SCL_VAL_IN 0x0010 -#define SDA_DIR_MASK 0x0100 -#define SDA_DIR 0x0200 -#define SDA_VAL_MASK 0x0400 -#define SDA_VAL_OUT 0x0800 -#define SDA_VAL_IN 0x1000 - -/* initialization states */ -#define INIT1 0x1 -#define INIT2 0x2 -#define INIT3 0x4 - -/* delays */ -#define CYCLE_DELAY 10 -#define TIMEOUT (HZ / 2) - -static void __iomem *ioaddr; - -/* The i810 GPIO registers have individual masks for each bit - so we never have to read before writing. Nice. */ - -static void bit_i810i2c_setscl(void *data, int val) -{ - writel((val ? SCL_VAL_OUT : 0) | SCL_DIR | SCL_DIR_MASK | SCL_VAL_MASK, - ioaddr + I810_GPIOB); - readl(ioaddr + I810_GPIOB); /* flush posted write */ -} - -static void bit_i810i2c_setsda(void *data, int val) -{ - writel((val ? SDA_VAL_OUT : 0) | SDA_DIR | SDA_DIR_MASK | SDA_VAL_MASK, - ioaddr + I810_GPIOB); - readl(ioaddr + I810_GPIOB); /* flush posted write */ -} - -/* The GPIO pins are open drain, so the pins could always remain outputs. - However, some chip versions don't latch the inputs unless they - are set as inputs. - We rely on the i2c-algo-bit routines to set the pins high before - reading the input from other chips. Following guidance in the 815 - prog. ref. guide, we do a "dummy write" of 0 to the register before - reading which forces the input value to be latched. We presume this - applies to the 810 as well; shouldn't hurt anyway. This is necessary to get - i2c_algo_bit bit_test=1 to pass. */ - -static int bit_i810i2c_getscl(void *data) -{ - writel(SCL_DIR_MASK, ioaddr + I810_GPIOB); - writel(0, ioaddr + I810_GPIOB); - return (0 != (readl(ioaddr + I810_GPIOB) & SCL_VAL_IN)); -} - -static int bit_i810i2c_getsda(void *data) -{ - writel(SDA_DIR_MASK, ioaddr + I810_GPIOB); - writel(0, ioaddr + I810_GPIOB); - return (0 != (readl(ioaddr + I810_GPIOB) & SDA_VAL_IN)); -} - -static void bit_i810ddc_setscl(void *data, int val) -{ - writel((val ? SCL_VAL_OUT : 0) | SCL_DIR | SCL_DIR_MASK | SCL_VAL_MASK, - ioaddr + I810_GPIOA); - readl(ioaddr + I810_GPIOA); /* flush posted write */ -} - -static void bit_i810ddc_setsda(void *data, int val) -{ - writel((val ? SDA_VAL_OUT : 0) | SDA_DIR | SDA_DIR_MASK | SDA_VAL_MASK, - ioaddr + I810_GPIOA); - readl(ioaddr + I810_GPIOA); /* flush posted write */ -} - -static int bit_i810ddc_getscl(void *data) -{ - writel(SCL_DIR_MASK, ioaddr + I810_GPIOA); - writel(0, ioaddr + I810_GPIOA); - return (0 != (readl(ioaddr + I810_GPIOA) & SCL_VAL_IN)); -} - -static int bit_i810ddc_getsda(void *data) -{ - writel(SDA_DIR_MASK, ioaddr + I810_GPIOA); - writel(0, ioaddr + I810_GPIOA); - return (0 != (readl(ioaddr + I810_GPIOA) & SDA_VAL_IN)); -} - -static int config_i810(struct pci_dev *dev) -{ - unsigned long cadr; - - /* map I810 memory */ - cadr = dev->resource[1].start; - cadr += I810_IOCONTROL_OFFSET; - cadr &= PCI_BASE_ADDRESS_MEM_MASK; - ioaddr = ioremap_nocache(cadr, 0x1000); - if (ioaddr) { - bit_i810i2c_setscl(NULL, 1); - bit_i810i2c_setsda(NULL, 1); - bit_i810ddc_setscl(NULL, 1); - bit_i810ddc_setsda(NULL, 1); - return 0; - } - return -ENODEV; -} - -static struct i2c_algo_bit_data i810_i2c_bit_data = { - .setsda = bit_i810i2c_setsda, - .setscl = bit_i810i2c_setscl, - .getsda = bit_i810i2c_getsda, - .getscl = bit_i810i2c_getscl, - .udelay = CYCLE_DELAY, - .timeout = TIMEOUT, -}; - -static struct i2c_adapter i810_i2c_adapter = { - .owner = THIS_MODULE, - .id = I2C_HW_B_I810, - .name = "I810/I815 I2C Adapter", - .algo_data = &i810_i2c_bit_data, -}; - -static struct i2c_algo_bit_data i810_ddc_bit_data = { - .setsda = bit_i810ddc_setsda, - .setscl = bit_i810ddc_setscl, - .getsda = bit_i810ddc_getsda, - .getscl = bit_i810ddc_getscl, - .udelay = CYCLE_DELAY, - .timeout = TIMEOUT, -}; - -static struct i2c_adapter i810_ddc_adapter = { - .owner = THIS_MODULE, - .id = I2C_HW_B_I810, - .name = "I810/I815 DDC Adapter", - .algo_data = &i810_ddc_bit_data, -}; - -static struct pci_device_id i810_ids[] __devinitdata = { - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG1) }, - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810_IG3) }, - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82810E_IG) }, - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82815_CGC) }, - { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82845G_IG) }, - { 0, }, -}; - -MODULE_DEVICE_TABLE (pci, i810_ids); - -static int __devinit i810_probe(struct pci_dev *dev, const struct pci_device_id *id) -{ - int retval; - - retval = config_i810(dev); - if (retval) - return retval; - dev_info(&dev->dev, "i810/i815 i2c device found.\n"); - - /* set up the sysfs linkage to our parent device */ - i810_i2c_adapter.dev.parent = &dev->dev; - i810_ddc_adapter.dev.parent = &dev->dev; - - retval = i2c_bit_add_bus(&i810_i2c_adapter); - if (retval) - return retval; - retval = i2c_bit_add_bus(&i810_ddc_adapter); - if (retval) - i2c_del_adapter(&i810_i2c_adapter); - return retval; -} - -static void __devexit i810_remove(struct pci_dev *dev) -{ - i2c_del_adapter(&i810_ddc_adapter); - i2c_del_adapter(&i810_i2c_adapter); - iounmap(ioaddr); -} - -static struct pci_driver i810_driver = { - .name = "i810_smbus", - .id_table = i810_ids, - .probe = i810_probe, - .remove = __devexit_p(i810_remove), -}; - -static int __init i2c_i810_init(void) -{ - return pci_register_driver(&i810_driver); -} - -static void __exit i2c_i810_exit(void) -{ - pci_unregister_driver(&i810_driver); -} - -MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl>, " - "Philip Edelbrock <phil@netroedge.com>, " - "Ralph Metzler <rjkm@thp.uni-koeln.de>, " - "and Mark D. Studebaker <mdsxyz123@yahoo.com>"); -MODULE_DESCRIPTION("I810/I815 I2C/DDC driver"); -MODULE_LICENSE("GPL"); - -module_init(i2c_i810_init); -module_exit(i2c_i810_exit); diff --git a/drivers/i2c/busses/i2c-ibm_iic.c b/drivers/i2c/busses/i2c-ibm_iic.c index 85dbf34382e1..651f2f1ae5b7 100644 --- a/drivers/i2c/busses/i2c-ibm_iic.c +++ b/drivers/i2c/busses/i2c-ibm_iic.c @@ -42,13 +42,8 @@ #include <asm/io.h> #include <linux/i2c.h> #include <linux/i2c-id.h> - -#ifdef CONFIG_IBM_OCP -#include <asm/ocp.h> -#include <asm/ibm4xx.h> -#else #include <linux/of_platform.h> -#endif +#include <linux/of_i2c.h> #include "i2c-ibm_iic.h" @@ -665,180 +660,6 @@ static inline u8 iic_clckdiv(unsigned int opb) return (u8)((opb + 9) / 10 - 1); } -#ifdef CONFIG_IBM_OCP -/* - * Register single IIC interface - */ -static int __devinit iic_probe(struct ocp_device *ocp){ - - struct ibm_iic_private* dev; - struct i2c_adapter* adap; - struct ocp_func_iic_data* iic_data = ocp->def->additions; - int ret; - - if (!iic_data) - printk(KERN_WARNING"ibm-iic%d: missing additional data!\n", - ocp->def->index); - - if (!(dev = kzalloc(sizeof(*dev), GFP_KERNEL))) { - printk(KERN_ERR "ibm-iic%d: failed to allocate device data\n", - ocp->def->index); - return -ENOMEM; - } - - dev->idx = ocp->def->index; - ocp_set_drvdata(ocp, dev); - - if (!request_mem_region(ocp->def->paddr, sizeof(struct iic_regs), - "ibm_iic")) { - ret = -EBUSY; - goto fail1; - } - - if (!(dev->vaddr = ioremap(ocp->def->paddr, sizeof(struct iic_regs)))){ - printk(KERN_ERR "ibm-iic%d: failed to ioremap device registers\n", - dev->idx); - ret = -ENXIO; - goto fail2; - } - - init_waitqueue_head(&dev->wq); - - dev->irq = iic_force_poll ? -1 : ocp->def->irq; - if (dev->irq >= 0){ - /* Disable interrupts until we finish initialization, - assumes level-sensitive IRQ setup... - */ - iic_interrupt_mode(dev, 0); - if (request_irq(dev->irq, iic_handler, 0, "IBM IIC", dev)){ - printk(KERN_ERR "ibm-iic%d: request_irq %d failed\n", - dev->idx, dev->irq); - /* Fallback to the polling mode */ - dev->irq = -1; - } - } - - if (dev->irq < 0) - printk(KERN_WARNING "ibm-iic%d: using polling mode\n", - dev->idx); - - /* Board specific settings */ - dev->fast_mode = iic_force_fast ? 1 : (iic_data ? iic_data->fast_mode : 0); - - /* clckdiv is the same for *all* IIC interfaces, - * but I'd rather make a copy than introduce another global. --ebs - */ - dev->clckdiv = iic_clckdiv(ocp_sys_info.opb_bus_freq); - DBG("%d: clckdiv = %d\n", dev->idx, dev->clckdiv); - - /* Initialize IIC interface */ - iic_dev_init(dev); - - /* Register it with i2c layer */ - adap = &dev->adap; - adap->dev.parent = &ocp->dev; - strcpy(adap->name, "IBM IIC"); - i2c_set_adapdata(adap, dev); - adap->id = I2C_HW_OCP; - adap->class = I2C_CLASS_HWMON; - adap->algo = &iic_algo; - adap->client_register = NULL; - adap->client_unregister = NULL; - adap->timeout = 1; - - /* - * If "dev->idx" is negative we consider it as zero. - * The reason to do so is to avoid sysfs names that only make - * sense when there are multiple adapters. - */ - adap->nr = dev->idx >= 0 ? dev->idx : 0; - - if ((ret = i2c_add_numbered_adapter(adap)) < 0) { - printk(KERN_ERR "ibm-iic%d: failed to register i2c adapter\n", - dev->idx); - goto fail; - } - - printk(KERN_INFO "ibm-iic%d: using %s mode\n", dev->idx, - dev->fast_mode ? "fast (400 kHz)" : "standard (100 kHz)"); - - return 0; - -fail: - if (dev->irq >= 0){ - iic_interrupt_mode(dev, 0); - free_irq(dev->irq, dev); - } - - iounmap(dev->vaddr); -fail2: - release_mem_region(ocp->def->paddr, sizeof(struct iic_regs)); -fail1: - ocp_set_drvdata(ocp, NULL); - kfree(dev); - return ret; -} - -/* - * Cleanup initialized IIC interface - */ -static void __devexit iic_remove(struct ocp_device *ocp) -{ - struct ibm_iic_private* dev = (struct ibm_iic_private*)ocp_get_drvdata(ocp); - BUG_ON(dev == NULL); - if (i2c_del_adapter(&dev->adap)){ - printk(KERN_ERR "ibm-iic%d: failed to delete i2c adapter :(\n", - dev->idx); - /* That's *very* bad, just shutdown IRQ ... */ - if (dev->irq >= 0){ - iic_interrupt_mode(dev, 0); - free_irq(dev->irq, dev); - dev->irq = -1; - } - } else { - if (dev->irq >= 0){ - iic_interrupt_mode(dev, 0); - free_irq(dev->irq, dev); - } - iounmap(dev->vaddr); - release_mem_region(ocp->def->paddr, sizeof(struct iic_regs)); - kfree(dev); - } -} - -static struct ocp_device_id ibm_iic_ids[] __devinitdata = -{ - { .vendor = OCP_VENDOR_IBM, .function = OCP_FUNC_IIC }, - { .vendor = OCP_VENDOR_INVALID } -}; - -MODULE_DEVICE_TABLE(ocp, ibm_iic_ids); - -static struct ocp_driver ibm_iic_driver = -{ - .name = "iic", - .id_table = ibm_iic_ids, - .probe = iic_probe, - .remove = __devexit_p(iic_remove), -#if defined(CONFIG_PM) - .suspend = NULL, - .resume = NULL, -#endif -}; - -static int __init iic_init(void) -{ - printk(KERN_INFO "IBM IIC driver v" DRIVER_VERSION "\n"); - return ocp_register_driver(&ibm_iic_driver); -} - -static void __exit iic_exit(void) -{ - ocp_unregister_driver(&ibm_iic_driver); -} - -#else /* !CONFIG_IBM_OCP */ - static int __devinit iic_request_irq(struct of_device *ofdev, struct ibm_iic_private *dev) { @@ -876,7 +697,7 @@ static int __devinit iic_probe(struct of_device *ofdev, struct device_node *np = ofdev->node; struct ibm_iic_private *dev; struct i2c_adapter *adap; - const u32 *indexp, *freq; + const u32 *freq; int ret; dev = kzalloc(sizeof(*dev), GFP_KERNEL); @@ -887,14 +708,6 @@ static int __devinit iic_probe(struct of_device *ofdev, dev_set_drvdata(&ofdev->dev, dev); - indexp = of_get_property(np, "index", NULL); - if (!indexp) { - dev_err(&ofdev->dev, "no index specified\n"); - ret = -EINVAL; - goto error_cleanup; - } - dev->idx = *indexp; - dev->vaddr = of_iomap(np, 0); if (dev->vaddr == NULL) { dev_err(&ofdev->dev, "failed to iomap device\n"); @@ -934,17 +747,19 @@ static int __devinit iic_probe(struct of_device *ofdev, strlcpy(adap->name, "IBM IIC", sizeof(adap->name)); i2c_set_adapdata(adap, dev); adap->id = I2C_HW_OCP; - adap->class = I2C_CLASS_HWMON; + adap->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; adap->algo = &iic_algo; adap->timeout = 1; - adap->nr = dev->idx; - ret = i2c_add_numbered_adapter(adap); + ret = i2c_add_adapter(adap); if (ret < 0) { dev_err(&ofdev->dev, "failed to register i2c adapter\n"); goto error_cleanup; } + /* Now register all the child nodes */ + of_register_i2c_devices(adap, np); + dev_info(&ofdev->dev, "using %s mode\n", dev->fast_mode ? "fast (400 kHz)" : "standard (100 kHz)"); @@ -987,11 +802,7 @@ static int __devexit iic_remove(struct of_device *ofdev) } static const struct of_device_id ibm_iic_match[] = { - { .compatible = "ibm,iic-405ex", }, - { .compatible = "ibm,iic-405gp", }, - { .compatible = "ibm,iic-440gp", }, - { .compatible = "ibm,iic-440gpx", }, - { .compatible = "ibm,iic-440grx", }, + { .compatible = "ibm,iic", }, {} }; @@ -1011,7 +822,6 @@ static void __exit iic_exit(void) { of_unregister_platform_driver(&ibm_iic_driver); } -#endif /* CONFIG_IBM_OCP */ module_init(iic_init); module_exit(iic_exit); diff --git a/drivers/i2c/busses/i2c-iop3xx.c b/drivers/i2c/busses/i2c-iop3xx.c index 39884e797594..fc2714ac0c0f 100644 --- a/drivers/i2c/busses/i2c-iop3xx.c +++ b/drivers/i2c/busses/i2c-iop3xx.c @@ -482,7 +482,7 @@ iop3xx_i2c_probe(struct platform_device *pdev) memcpy(new_adapter->name, pdev->name, strlen(pdev->name)); new_adapter->id = I2C_HW_IOP3XX; new_adapter->owner = THIS_MODULE; - new_adapter->class = I2C_CLASS_HWMON; + new_adapter->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; new_adapter->dev.parent = &pdev->dev; new_adapter->nr = pdev->id; diff --git a/drivers/i2c/busses/i2c-isch.c b/drivers/i2c/busses/i2c-isch.c new file mode 100644 index 000000000000..b9c01aa90036 --- /dev/null +++ b/drivers/i2c/busses/i2c-isch.c @@ -0,0 +1,339 @@ +/* + i2c-isch.c - Linux kernel driver for Intel SCH chipset SMBus + - Based on i2c-piix4.c + Copyright (c) 1998 - 2002 Frodo Looijaard <frodol@dds.nl> and + Philip Edelbrock <phil@netroedge.com> + - Intel SCH support + Copyright (c) 2007 - 2008 Jacob Jun Pan <jacob.jun.pan@intel.com> + + This program is free software; you can redistribute it and/or modify + it under the terms of the GNU General Public License version 2 as + published by the Free Software Foundation. + + This program is distributed in the hope that it will be useful, + but WITHOUT ANY WARRANTY; without even the implied warranty of + MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + GNU General Public License for more details. + + You should have received a copy of the GNU General Public License + along with this program; if not, write to the Free Software + Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. +*/ + +/* + Supports: + Intel SCH chipsets (AF82US15W, AF82US15L, AF82UL11L) + Note: we assume there can only be one device, with one SMBus interface. +*/ + +#include <linux/module.h> +#include <linux/pci.h> +#include <linux/kernel.h> +#include <linux/delay.h> +#include <linux/stddef.h> +#include <linux/ioport.h> +#include <linux/i2c.h> +#include <linux/init.h> +#include <linux/io.h> +#include <linux/acpi.h> + +/* SCH SMBus address offsets */ +#define SMBHSTCNT (0 + sch_smba) +#define SMBHSTSTS (1 + sch_smba) +#define SMBHSTADD (4 + sch_smba) /* TSA */ +#define SMBHSTCMD (5 + sch_smba) +#define SMBHSTDAT0 (6 + sch_smba) +#define SMBHSTDAT1 (7 + sch_smba) +#define SMBBLKDAT (0x20 + sch_smba) + +/* count for request_region */ +#define SMBIOSIZE 64 + +/* PCI Address Constants */ +#define SMBBA_SCH 0x40 + +/* Other settings */ +#define MAX_TIMEOUT 500 + +/* I2C constants */ +#define SCH_QUICK 0x00 +#define SCH_BYTE 0x01 +#define SCH_BYTE_DATA 0x02 +#define SCH_WORD_DATA 0x03 +#define SCH_BLOCK_DATA 0x05 + +static unsigned short sch_smba; +static struct pci_driver sch_driver; +static struct i2c_adapter sch_adapter; + +/* + * Start the i2c transaction -- the i2c_access will prepare the transaction + * and this function will execute it. + * return 0 for success and others for failure. + */ +static int sch_transaction(void) +{ + int temp; + int result = 0; + int timeout = 0; + + dev_dbg(&sch_adapter.dev, "Transaction (pre): CNT=%02x, CMD=%02x, " + "ADD=%02x, DAT0=%02x, DAT1=%02x\n", inb(SMBHSTCNT), + inb(SMBHSTCMD), inb(SMBHSTADD), inb(SMBHSTDAT0), + inb(SMBHSTDAT1)); + + /* Make sure the SMBus host is ready to start transmitting */ + temp = inb(SMBHSTSTS) & 0x0f; + if (temp) { + /* Can not be busy since we checked it in sch_access */ + if (temp & 0x01) { + dev_dbg(&sch_adapter.dev, "Completion (%02x). " + "Clear...\n", temp); + } + if (temp & 0x06) { + dev_dbg(&sch_adapter.dev, "SMBus error (%02x). " + "Resetting...\n", temp); + } + outb(temp, SMBHSTSTS); + temp = inb(SMBHSTSTS) & 0x0f; + if (temp) { + dev_err(&sch_adapter.dev, + "SMBus is not ready: (%02x)\n", temp); + return -EAGAIN; + } + } + + /* start the transaction by setting bit 4 */ + outb(inb(SMBHSTCNT) | 0x10, SMBHSTCNT); + + do { + msleep(1); + temp = inb(SMBHSTSTS) & 0x0f; + } while ((temp & 0x08) && (timeout++ < MAX_TIMEOUT)); + + /* If the SMBus is still busy, we give up */ + if (timeout >= MAX_TIMEOUT) { + dev_err(&sch_adapter.dev, "SMBus Timeout!\n"); + result = -ETIMEDOUT; + } + if (temp & 0x04) { + result = -EIO; + dev_dbg(&sch_adapter.dev, "Bus collision! SMBus may be " + "locked until next hard reset. (sorry!)\n"); + /* Clock stops and slave is stuck in mid-transmission */ + } else if (temp & 0x02) { + result = -EIO; + dev_err(&sch_adapter.dev, "Error: no response!\n"); + } else if (temp & 0x01) { + dev_dbg(&sch_adapter.dev, "Post complete!\n"); + outb(temp, SMBHSTSTS); + temp = inb(SMBHSTSTS) & 0x07; + if (temp & 0x06) { + /* Completion clear failed */ + dev_dbg(&sch_adapter.dev, "Failed reset at end of " + "transaction (%02x), Bus error!\n", temp); + } + } else { + result = -ENXIO; + dev_dbg(&sch_adapter.dev, "No such address.\n"); + } + dev_dbg(&sch_adapter.dev, "Transaction (post): CNT=%02x, CMD=%02x, " + "ADD=%02x, DAT0=%02x, DAT1=%02x\n", inb(SMBHSTCNT), + inb(SMBHSTCMD), inb(SMBHSTADD), inb(SMBHSTDAT0), + inb(SMBHSTDAT1)); + return result; +} + +/* + * This is the main access entry for i2c-sch access + * adap is i2c_adapter pointer, addr is the i2c device bus address, read_write + * (0 for read and 1 for write), size is i2c transaction type and data is the + * union of transaction for data to be transfered or data read from bus. + * return 0 for success and others for failure. + */ +static s32 sch_access(struct i2c_adapter *adap, u16 addr, + unsigned short flags, char read_write, + u8 command, int size, union i2c_smbus_data *data) +{ + int i, len, temp, rc; + + /* Make sure the SMBus host is not busy */ + temp = inb(SMBHSTSTS) & 0x0f; + if (temp & 0x08) { + dev_dbg(&sch_adapter.dev, "SMBus busy (%02x)\n", temp); + return -EAGAIN; + } + dev_dbg(&sch_adapter.dev, "access size: %d %s\n", size, + (read_write)?"READ":"WRITE"); + switch (size) { + case I2C_SMBUS_QUICK: + outb((addr << 1) | read_write, SMBHSTADD); + size = SCH_QUICK; + break; + case I2C_SMBUS_BYTE: + outb((addr << 1) | read_write, SMBHSTADD); + if (read_write == I2C_SMBUS_WRITE) + outb(command, SMBHSTCMD); + size = SCH_BYTE; + break; + case I2C_SMBUS_BYTE_DATA: + outb((addr << 1) | read_write, SMBHSTADD); + outb(command, SMBHSTCMD); + if (read_write == I2C_SMBUS_WRITE) + outb(data->byte, SMBHSTDAT0); + size = SCH_BYTE_DATA; + break; + case I2C_SMBUS_WORD_DATA: + outb((addr << 1) | read_write, SMBHSTADD); + outb(command, SMBHSTCMD); + if (read_write == I2C_SMBUS_WRITE) { + outb(data->word & 0xff, SMBHSTDAT0); + outb((data->word & 0xff00) >> 8, SMBHSTDAT1); + } + size = SCH_WORD_DATA; + break; + case I2C_SMBUS_BLOCK_DATA: + outb((addr << 1) | read_write, SMBHSTADD); + outb(command, SMBHSTCMD); + if (read_write == I2C_SMBUS_WRITE) { + len = data->block[0]; + if (len == 0 || len > I2C_SMBUS_BLOCK_MAX) + return -EINVAL; + outb(len, SMBHSTDAT0); + for (i = 1; i <= len; i++) + outb(data->block[i], SMBBLKDAT+i-1); + } + size = SCH_BLOCK_DATA; + break; + default: + dev_warn(&adap->dev, "Unsupported transaction %d\n", size); + return -EOPNOTSUPP; + } + dev_dbg(&sch_adapter.dev, "write size %d to 0x%04x\n", size, SMBHSTCNT); + outb((inb(SMBHSTCNT) & 0xb0) | (size & 0x7), SMBHSTCNT); + + rc = sch_transaction(); + if (rc) /* Error in transaction */ + return rc; + + if ((read_write == I2C_SMBUS_WRITE) || (size == SCH_QUICK)) + return 0; + + switch (size) { + case SCH_BYTE: + case SCH_BYTE_DATA: + data->byte = inb(SMBHSTDAT0); + break; + case SCH_WORD_DATA: + data->word = inb(SMBHSTDAT0) + (inb(SMBHSTDAT1) << 8); + break; + case SCH_BLOCK_DATA: + data->block[0] = inb(SMBHSTDAT0); + if (data->block[0] == 0 || data->block[0] > I2C_SMBUS_BLOCK_MAX) + return -EPROTO; + for (i = 1; i <= data->block[0]; i++) + data->block[i] = inb(SMBBLKDAT+i-1); + break; + } + return 0; +} + +static u32 sch_func(struct i2c_adapter *adapter) +{ + return I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE | + I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA | + I2C_FUNC_SMBUS_BLOCK_DATA; +} + +static const struct i2c_algorithm smbus_algorithm = { + .smbus_xfer = sch_access, + .functionality = sch_func, +}; + +static struct i2c_adapter sch_adapter = { + .owner = THIS_MODULE, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, + .algo = &smbus_algorithm, +}; + +static struct pci_device_id sch_ids[] = { + { PCI_DEVICE(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_SCH_LPC) }, + { 0, } +}; + +MODULE_DEVICE_TABLE(pci, sch_ids); + +static int __devinit sch_probe(struct pci_dev *dev, + const struct pci_device_id *id) +{ + int retval; + unsigned int smba; + + pci_read_config_dword(dev, SMBBA_SCH, &smba); + if (!(smba & (1 << 31))) { + dev_err(&dev->dev, "SMBus I/O space disabled!\n"); + return -ENODEV; + } + + sch_smba = (unsigned short)smba; + if (sch_smba == 0) { + dev_err(&dev->dev, "SMBus base address uninitialized!\n"); + return -ENODEV; + } + if (acpi_check_region(sch_smba, SMBIOSIZE, sch_driver.name)) + return -EBUSY; + if (!request_region(sch_smba, SMBIOSIZE, sch_driver.name)) { + dev_err(&dev->dev, "SMBus region 0x%x already in use!\n", + sch_smba); + return -EBUSY; + } + dev_dbg(&dev->dev, "SMBA = 0x%X\n", sch_smba); + + /* set up the sysfs linkage to our parent device */ + sch_adapter.dev.parent = &dev->dev; + + snprintf(sch_adapter.name, sizeof(sch_adapter.name), + "SMBus SCH adapter at %04x", sch_smba); + + retval = i2c_add_adapter(&sch_adapter); + if (retval) { + dev_err(&dev->dev, "Couldn't register adapter!\n"); + release_region(sch_smba, SMBIOSIZE); + sch_smba = 0; + } + + return retval; +} + +static void __devexit sch_remove(struct pci_dev *dev) +{ + if (sch_smba) { + i2c_del_adapter(&sch_adapter); + release_region(sch_smba, SMBIOSIZE); + sch_smba = 0; + } +} + +static struct pci_driver sch_driver = { + .name = "isch_smbus", + .id_table = sch_ids, + .probe = sch_probe, + .remove = __devexit_p(sch_remove), +}; + +static int __init i2c_sch_init(void) +{ + return pci_register_driver(&sch_driver); +} + +static void __exit i2c_sch_exit(void) +{ + pci_unregister_driver(&sch_driver); +} + +MODULE_AUTHOR("Jacob Pan <jacob.jun.pan@intel.com>"); +MODULE_DESCRIPTION("Intel SCH SMBus driver"); +MODULE_LICENSE("GPL"); + +module_init(i2c_sch_init); +module_exit(i2c_sch_exit); diff --git a/drivers/i2c/busses/i2c-mpc.c b/drivers/i2c/busses/i2c-mpc.c index a076129de7e8..27443f073bc9 100644 --- a/drivers/i2c/busses/i2c-mpc.c +++ b/drivers/i2c/busses/i2c-mpc.c @@ -17,7 +17,8 @@ #include <linux/module.h> #include <linux/sched.h> #include <linux/init.h> -#include <linux/platform_device.h> +#include <linux/of_platform.h> +#include <linux/of_i2c.h> #include <asm/io.h> #include <linux/fsl_devices.h> @@ -25,13 +26,13 @@ #include <linux/interrupt.h> #include <linux/delay.h> -#define MPC_I2C_ADDR 0x00 +#define DRV_NAME "mpc-i2c" + #define MPC_I2C_FDR 0x04 #define MPC_I2C_CR 0x08 #define MPC_I2C_SR 0x0c #define MPC_I2C_DR 0x10 #define MPC_I2C_DFSRR 0x14 -#define MPC_I2C_REGION 0x20 #define CCR_MEN 0x80 #define CCR_MIEN 0x40 @@ -311,106 +312,121 @@ static struct i2c_adapter mpc_ops = { .name = "MPC adapter", .id = I2C_HW_MPC107, .algo = &mpc_algo, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .timeout = 1, }; -static int fsl_i2c_probe(struct platform_device *pdev) +static int __devinit fsl_i2c_probe(struct of_device *op, const struct of_device_id *match) { int result = 0; struct mpc_i2c *i2c; - struct fsl_i2c_platform_data *pdata; - struct resource *r = platform_get_resource(pdev, IORESOURCE_MEM, 0); - - pdata = (struct fsl_i2c_platform_data *) pdev->dev.platform_data; i2c = kzalloc(sizeof(*i2c), GFP_KERNEL); if (!i2c) return -ENOMEM; - i2c->irq = platform_get_irq(pdev, 0); - if (i2c->irq < 0) - i2c->irq = NO_IRQ; /* Use polling */ + if (of_get_property(op->node, "dfsrr", NULL)) + i2c->flags |= FSL_I2C_DEV_SEPARATE_DFSRR; - i2c->flags = pdata->device_flags; - init_waitqueue_head(&i2c->queue); + if (of_device_is_compatible(op->node, "fsl,mpc5200-i2c") || + of_device_is_compatible(op->node, "mpc5200-i2c")) + i2c->flags |= FSL_I2C_DEV_CLOCK_5200; - i2c->base = ioremap((phys_addr_t)r->start, MPC_I2C_REGION); + init_waitqueue_head(&i2c->queue); + i2c->base = of_iomap(op->node, 0); if (!i2c->base) { printk(KERN_ERR "i2c-mpc - failed to map controller\n"); result = -ENOMEM; goto fail_map; } - if (i2c->irq != NO_IRQ) - if ((result = request_irq(i2c->irq, mpc_i2c_isr, - IRQF_SHARED, "i2c-mpc", i2c)) < 0) { - printk(KERN_ERR - "i2c-mpc - failed to attach interrupt\n"); - goto fail_irq; + i2c->irq = irq_of_parse_and_map(op->node, 0); + if (i2c->irq != NO_IRQ) { /* i2c->irq = NO_IRQ implies polling */ + result = request_irq(i2c->irq, mpc_i2c_isr, + IRQF_SHARED, "i2c-mpc", i2c); + if (result < 0) { + printk(KERN_ERR "i2c-mpc - failed to attach interrupt\n"); + goto fail_request; } - + } + mpc_i2c_setclock(i2c); - platform_set_drvdata(pdev, i2c); + + dev_set_drvdata(&op->dev, i2c); i2c->adap = mpc_ops; - i2c->adap.nr = pdev->id; i2c_set_adapdata(&i2c->adap, i2c); - i2c->adap.dev.parent = &pdev->dev; - if ((result = i2c_add_numbered_adapter(&i2c->adap)) < 0) { + i2c->adap.dev.parent = &op->dev; + + result = i2c_add_adapter(&i2c->adap); + if (result < 0) { printk(KERN_ERR "i2c-mpc - failed to add adapter\n"); goto fail_add; } + of_register_i2c_devices(&i2c->adap, op->node); return result; - fail_add: - if (i2c->irq != NO_IRQ) - free_irq(i2c->irq, i2c); - fail_irq: - iounmap(i2c->base); - fail_map: + fail_add: + dev_set_drvdata(&op->dev, NULL); + free_irq(i2c->irq, i2c); + fail_request: + irq_dispose_mapping(i2c->irq); + iounmap(i2c->base); + fail_map: kfree(i2c); return result; }; -static int fsl_i2c_remove(struct platform_device *pdev) +static int __devexit fsl_i2c_remove(struct of_device *op) { - struct mpc_i2c *i2c = platform_get_drvdata(pdev); + struct mpc_i2c *i2c = dev_get_drvdata(&op->dev); i2c_del_adapter(&i2c->adap); - platform_set_drvdata(pdev, NULL); + dev_set_drvdata(&op->dev, NULL); if (i2c->irq != NO_IRQ) free_irq(i2c->irq, i2c); + irq_dispose_mapping(i2c->irq); iounmap(i2c->base); kfree(i2c); return 0; }; -/* work with hotplug and coldplug */ -MODULE_ALIAS("platform:fsl-i2c"); +static const struct of_device_id mpc_i2c_of_match[] = { + {.compatible = "fsl-i2c",}, + {}, +}; +MODULE_DEVICE_TABLE(of, mpc_i2c_of_match); + /* Structure for a device driver */ -static struct platform_driver fsl_i2c_driver = { - .probe = fsl_i2c_probe, - .remove = fsl_i2c_remove, - .driver = { - .owner = THIS_MODULE, - .name = "fsl-i2c", +static struct of_platform_driver mpc_i2c_driver = { + .match_table = mpc_i2c_of_match, + .probe = fsl_i2c_probe, + .remove = __devexit_p(fsl_i2c_remove), + .driver = { + .owner = THIS_MODULE, + .name = DRV_NAME, }, }; static int __init fsl_i2c_init(void) { - return platform_driver_register(&fsl_i2c_driver); + int rv; + + rv = of_register_platform_driver(&mpc_i2c_driver); + if (rv) + printk(KERN_ERR DRV_NAME + " of_register_platform_driver failed (%i)\n", rv); + return rv; } static void __exit fsl_i2c_exit(void) { - platform_driver_unregister(&fsl_i2c_driver); + of_unregister_platform_driver(&mpc_i2c_driver); } module_init(fsl_i2c_init); diff --git a/drivers/i2c/busses/i2c-mv64xxx.c b/drivers/i2c/busses/i2c-mv64xxx.c index 036e6a883e67..9e8118d2fe64 100644 --- a/drivers/i2c/busses/i2c-mv64xxx.c +++ b/drivers/i2c/busses/i2c-mv64xxx.c @@ -530,7 +530,7 @@ mv64xxx_i2c_probe(struct platform_device *pd) drv_data->adapter.id = I2C_HW_MV64XXX; drv_data->adapter.algo = &mv64xxx_i2c_algo; drv_data->adapter.owner = THIS_MODULE; - drv_data->adapter.class = I2C_CLASS_HWMON; + drv_data->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD; drv_data->adapter.timeout = pdata->timeout; drv_data->adapter.nr = pd->id; platform_set_drvdata(pd, drv_data); diff --git a/drivers/i2c/busses/i2c-nforce2-s4985.c b/drivers/i2c/busses/i2c-nforce2-s4985.c new file mode 100644 index 000000000000..d1a4cbcf2aa4 --- /dev/null +++ b/drivers/i2c/busses/i2c-nforce2-s4985.c @@ -0,0 +1,256 @@ +/* + * i2c-nforce2-s4985.c - i2c-nforce2 extras for the Tyan S4985 motherboard + * + * Copyright (C) 2008 Jean Delvare <khali@linux-fr.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ + +/* + * We select the channels by sending commands to the Philips + * PCA9556 chip at I2C address 0x18. The main adapter is used for + * the non-multiplexed part of the bus, and 4 virtual adapters + * are defined for the multiplexed addresses: 0x50-0x53 (memory + * module EEPROM) located on channels 1-4. We define one virtual + * adapter per CPU, which corresponds to one multiplexed channel: + * CPU0: virtual adapter 1, channel 1 + * CPU1: virtual adapter 2, channel 2 + * CPU2: virtual adapter 3, channel 3 + * CPU3: virtual adapter 4, channel 4 + */ + +#include <linux/module.h> +#include <linux/kernel.h> +#include <linux/slab.h> +#include <linux/init.h> +#include <linux/i2c.h> +#include <linux/mutex.h> + +extern struct i2c_adapter *nforce2_smbus; + +static struct i2c_adapter *s4985_adapter; +static struct i2c_algorithm *s4985_algo; + +/* Wrapper access functions for multiplexed SMBus */ +static DEFINE_MUTEX(nforce2_lock); + +static s32 nforce2_access_virt0(struct i2c_adapter *adap, u16 addr, + unsigned short flags, char read_write, + u8 command, int size, + union i2c_smbus_data *data) +{ + int error; + + /* We exclude the multiplexed addresses */ + if ((addr & 0xfc) == 0x50 || (addr & 0xfc) == 0x30 + || addr == 0x18) + return -ENXIO; + + mutex_lock(&nforce2_lock); + error = nforce2_smbus->algo->smbus_xfer(adap, addr, flags, read_write, + command, size, data); + mutex_unlock(&nforce2_lock); + + return error; +} + +/* We remember the last used channels combination so as to only switch + channels when it is really needed. This greatly reduces the SMBus + overhead, but also assumes that nobody will be writing to the PCA9556 + in our back. */ +static u8 last_channels; + +static inline s32 nforce2_access_channel(struct i2c_adapter *adap, u16 addr, + unsigned short flags, char read_write, + u8 command, int size, + union i2c_smbus_data *data, + u8 channels) +{ + int error; + + /* We exclude the non-multiplexed addresses */ + if ((addr & 0xfc) != 0x50 && (addr & 0xfc) != 0x30) + return -ENXIO; + + mutex_lock(&nforce2_lock); + if (last_channels != channels) { + union i2c_smbus_data mplxdata; + mplxdata.byte = channels; + + error = nforce2_smbus->algo->smbus_xfer(adap, 0x18, 0, + I2C_SMBUS_WRITE, 0x01, + I2C_SMBUS_BYTE_DATA, + &mplxdata); + if (error) + goto UNLOCK; + last_channels = channels; + } + error = nforce2_smbus->algo->smbus_xfer(adap, addr, flags, read_write, + command, size, data); + +UNLOCK: + mutex_unlock(&nforce2_lock); + return error; +} + +static s32 nforce2_access_virt1(struct i2c_adapter *adap, u16 addr, + unsigned short flags, char read_write, + u8 command, int size, + union i2c_smbus_data *data) +{ + /* CPU0: channel 1 enabled */ + return nforce2_access_channel(adap, addr, flags, read_write, command, + size, data, 0x02); +} + +static s32 nforce2_access_virt2(struct i2c_adapter *adap, u16 addr, + unsigned short flags, char read_write, + u8 command, int size, + union i2c_smbus_data *data) +{ + /* CPU1: channel 2 enabled */ + return nforce2_access_channel(adap, addr, flags, read_write, command, + size, data, 0x04); +} + +static s32 nforce2_access_virt3(struct i2c_adapter *adap, u16 addr, + unsigned short flags, char read_write, + u8 command, int size, + union i2c_smbus_data *data) +{ + /* CPU2: channel 3 enabled */ + return nforce2_access_channel(adap, addr, flags, read_write, command, + size, data, 0x08); +} + +static s32 nforce2_access_virt4(struct i2c_adapter *adap, u16 addr, + unsigned short flags, char read_write, + u8 command, int size, + union i2c_smbus_data *data) +{ + /* CPU3: channel 4 enabled */ + return nforce2_access_channel(adap, addr, flags, read_write, command, + size, data, 0x10); +} + +static int __init nforce2_s4985_init(void) +{ + int i, error; + union i2c_smbus_data ioconfig; + + /* Configure the PCA9556 multiplexer */ + ioconfig.byte = 0x00; /* All I/O to output mode */ + error = i2c_smbus_xfer(nforce2_smbus, 0x18, 0, I2C_SMBUS_WRITE, 0x03, + I2C_SMBUS_BYTE_DATA, &ioconfig); + if (error) { + dev_err(&nforce2_smbus->dev, "PCA9556 configuration failed\n"); + error = -EIO; + goto ERROR0; + } + + /* Unregister physical bus */ + if (!nforce2_smbus) + return -ENODEV; + error = i2c_del_adapter(nforce2_smbus); + if (error) { + dev_err(&nforce2_smbus->dev, "Physical bus removal failed\n"); + goto ERROR0; + } + + printk(KERN_INFO "Enabling SMBus multiplexing for Tyan S4985\n"); + /* Define the 5 virtual adapters and algorithms structures */ + s4985_adapter = kzalloc(5 * sizeof(struct i2c_adapter), GFP_KERNEL); + if (!s4985_adapter) { + error = -ENOMEM; + goto ERROR1; + } + s4985_algo = kzalloc(5 * sizeof(struct i2c_algorithm), GFP_KERNEL); + if (!s4985_algo) { + error = -ENOMEM; + goto ERROR2; + } + + /* Fill in the new structures */ + s4985_algo[0] = *(nforce2_smbus->algo); + s4985_algo[0].smbus_xfer = nforce2_access_virt0; + s4985_adapter[0] = *nforce2_smbus; + s4985_adapter[0].algo = s4985_algo; + s4985_adapter[0].dev.parent = nforce2_smbus->dev.parent; + for (i = 1; i < 5; i++) { + s4985_algo[i] = *(nforce2_smbus->algo); + s4985_adapter[i] = *nforce2_smbus; + snprintf(s4985_adapter[i].name, sizeof(s4985_adapter[i].name), + "SMBus nForce2 adapter (CPU%d)", i - 1); + s4985_adapter[i].algo = s4985_algo + i; + s4985_adapter[i].dev.parent = nforce2_smbus->dev.parent; + } + s4985_algo[1].smbus_xfer = nforce2_access_virt1; + s4985_algo[2].smbus_xfer = nforce2_access_virt2; + s4985_algo[3].smbus_xfer = nforce2_access_virt3; + s4985_algo[4].smbus_xfer = nforce2_access_virt4; + + /* Register virtual adapters */ + for (i = 0; i < 5; i++) { + error = i2c_add_adapter(s4985_adapter + i); + if (error) { + printk(KERN_ERR "i2c-nforce2-s4985: " + "Virtual adapter %d registration " + "failed, module not inserted\n", i); + for (i--; i >= 0; i--) + i2c_del_adapter(s4985_adapter + i); + goto ERROR3; + } + } + + return 0; + +ERROR3: + kfree(s4985_algo); + s4985_algo = NULL; +ERROR2: + kfree(s4985_adapter); + s4985_adapter = NULL; +ERROR1: + /* Restore physical bus */ + i2c_add_adapter(nforce2_smbus); +ERROR0: + return error; +} + +static void __exit nforce2_s4985_exit(void) +{ + if (s4985_adapter) { + int i; + + for (i = 0; i < 5; i++) + i2c_del_adapter(s4985_adapter+i); + kfree(s4985_adapter); + s4985_adapter = NULL; + } + kfree(s4985_algo); + s4985_algo = NULL; + + /* Restore physical bus */ + if (i2c_add_adapter(nforce2_smbus)) + printk(KERN_ERR "i2c-nforce2-s4985: " + "Physical bus restoration failed\n"); +} + +MODULE_AUTHOR("Jean Delvare <khali@linux-fr.org>"); +MODULE_DESCRIPTION("S4985 SMBus multiplexing"); +MODULE_LICENSE("GPL"); + +module_init(nforce2_s4985_init); +module_exit(nforce2_s4985_exit); diff --git a/drivers/i2c/busses/i2c-nforce2.c b/drivers/i2c/busses/i2c-nforce2.c index 43c9f8df9509..3b19bc41a60b 100644 --- a/drivers/i2c/busses/i2c-nforce2.c +++ b/drivers/i2c/busses/i2c-nforce2.c @@ -51,6 +51,7 @@ #include <linux/i2c.h> #include <linux/delay.h> #include <linux/dmi.h> +#include <linux/acpi.h> #include <asm/io.h> MODULE_LICENSE("GPL"); @@ -124,6 +125,20 @@ static struct dmi_system_id __devinitdata nforce2_dmi_blacklist2[] = { static struct pci_driver nforce2_driver; +/* For multiplexing support, we need a global reference to the 1st + SMBus channel */ +#if defined CONFIG_I2C_NFORCE2_S4985 || defined CONFIG_I2C_NFORCE2_S4985_MODULE +struct i2c_adapter *nforce2_smbus; +EXPORT_SYMBOL_GPL(nforce2_smbus); + +static void nforce2_set_reference(struct i2c_adapter *adap) +{ + nforce2_smbus = adap; +} +#else +static inline void nforce2_set_reference(struct i2c_adapter *adap) { } +#endif + static void nforce2_abort(struct i2c_adapter *adap) { struct nforce2_smbus *smbus = adap->algo_data; @@ -158,16 +173,16 @@ static int nforce2_check_status(struct i2c_adapter *adap) dev_dbg(&adap->dev, "SMBus Timeout!\n"); if (smbus->can_abort) nforce2_abort(adap); - return -1; + return -ETIMEDOUT; } if (!(temp & NVIDIA_SMB_STS_DONE) || (temp & NVIDIA_SMB_STS_STATUS)) { dev_dbg(&adap->dev, "Transaction failed (0x%02x)!\n", temp); - return -1; + return -EIO; } return 0; } -/* Return -1 on error */ +/* Return negative errno on error */ static s32 nforce2_access(struct i2c_adapter * adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data * data) @@ -175,7 +190,7 @@ static s32 nforce2_access(struct i2c_adapter * adap, u16 addr, struct nforce2_smbus *smbus = adap->algo_data; unsigned char protocol, pec; u8 len; - int i; + int i, status; protocol = (read_write == I2C_SMBUS_READ) ? NVIDIA_SMB_PRTCL_READ : NVIDIA_SMB_PRTCL_WRITE; @@ -219,7 +234,7 @@ static s32 nforce2_access(struct i2c_adapter * adap, u16 addr, "Transaction failed " "(requested block size: %d)\n", len); - return -1; + return -EINVAL; } outb_p(len, NVIDIA_SMB_BCNT); for (i = 0; i < I2C_SMBUS_BLOCK_MAX; i++) @@ -231,14 +246,15 @@ static s32 nforce2_access(struct i2c_adapter * adap, u16 addr, default: dev_err(&adap->dev, "Unsupported transaction %d\n", size); - return -1; + return -EOPNOTSUPP; } outb_p((addr & 0x7f) << 1, NVIDIA_SMB_ADDR); outb_p(protocol, NVIDIA_SMB_PRTCL); - if (nforce2_check_status(adap)) - return -1; + status = nforce2_check_status(adap); + if (status) + return status; if (read_write == I2C_SMBUS_WRITE) return 0; @@ -260,7 +276,7 @@ static s32 nforce2_access(struct i2c_adapter * adap, u16 addr, dev_err(&adap->dev, "Transaction failed " "(received block size: 0x%02x)\n", len); - return -1; + return -EPROTO; } for (i = 0; i < len; i++) data->block[i+1] = inb_p(NVIDIA_SMB_DATA + i); @@ -321,21 +337,26 @@ static int __devinit nforce2_probe_smb (struct pci_dev *dev, int bar, != PCIBIOS_SUCCESSFUL) { dev_err(&dev->dev, "Error reading PCI config for %s\n", name); - return -1; + return -EIO; } smbus->base = iobase & PCI_BASE_ADDRESS_IO_MASK; smbus->size = 64; } + error = acpi_check_region(smbus->base, smbus->size, + nforce2_driver.name); + if (error) + return -1; + if (!request_region(smbus->base, smbus->size, nforce2_driver.name)) { dev_err(&smbus->adapter.dev, "Error requesting region %02x .. %02X for %s\n", smbus->base, smbus->base+smbus->size-1, name); - return -1; + return -EBUSY; } smbus->adapter.owner = THIS_MODULE; smbus->adapter.id = I2C_HW_SMBUS_NFORCE2; - smbus->adapter.class = I2C_CLASS_HWMON; + smbus->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD; smbus->adapter.algo = &smbus_algorithm; smbus->adapter.algo_data = smbus; smbus->adapter.dev.parent = &dev->dev; @@ -346,7 +367,7 @@ static int __devinit nforce2_probe_smb (struct pci_dev *dev, int bar, if (error) { dev_err(&smbus->adapter.dev, "Failed to register adapter.\n"); release_region(smbus->base, smbus->size); - return -1; + return error; } dev_info(&smbus->adapter.dev, "nForce2 SMBus adapter at %#x\n", smbus->base); return 0; @@ -398,6 +419,7 @@ static int __devinit nforce2_probe(struct pci_dev *dev, const struct pci_device_ return -ENODEV; } + nforce2_set_reference(&smbuses[0].adapter); return 0; } @@ -406,6 +428,7 @@ static void __devexit nforce2_remove(struct pci_dev *dev) { struct nforce2_smbus *smbuses = (void*) pci_get_drvdata(dev); + nforce2_set_reference(NULL); if (smbuses[0].base) { i2c_del_adapter(&smbuses[0].adapter); release_region(smbuses[0].base, smbuses[0].size); diff --git a/drivers/i2c/busses/i2c-ocores.c b/drivers/i2c/busses/i2c-ocores.c index f145692cbb76..e5193bf75483 100644 --- a/drivers/i2c/busses/i2c-ocores.c +++ b/drivers/i2c/busses/i2c-ocores.c @@ -29,6 +29,7 @@ struct ocores_i2c { int pos; int nmsgs; int state; /* see STATE_ */ + int clock_khz; }; /* registers */ @@ -173,8 +174,7 @@ static int ocores_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num) return -ETIMEDOUT; } -static void ocores_init(struct ocores_i2c *i2c, - struct ocores_i2c_platform_data *pdata) +static void ocores_init(struct ocores_i2c *i2c) { int prescale; u8 ctrl = oc_getreg(i2c, OCI2C_CONTROL); @@ -182,7 +182,7 @@ static void ocores_init(struct ocores_i2c *i2c, /* make sure the device is disabled */ oc_setreg(i2c, OCI2C_CONTROL, ctrl & ~(OCI2C_CTRL_EN|OCI2C_CTRL_IEN)); - prescale = (pdata->clock_khz / (5*100)) - 1; + prescale = (i2c->clock_khz / (5*100)) - 1; oc_setreg(i2c, OCI2C_PRELOW, prescale & 0xff); oc_setreg(i2c, OCI2C_PREHIGH, prescale >> 8); @@ -205,7 +205,7 @@ static const struct i2c_algorithm ocores_algorithm = { static struct i2c_adapter ocores_adapter = { .owner = THIS_MODULE, .name = "i2c-ocores", - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &ocores_algorithm, }; @@ -248,7 +248,8 @@ static int __devinit ocores_i2c_probe(struct platform_device *pdev) } i2c->regstep = pdata->regstep; - ocores_init(i2c, pdata); + i2c->clock_khz = pdata->clock_khz; + ocores_init(i2c); init_waitqueue_head(&i2c->wait); ret = request_irq(res2->start, ocores_isr, 0, pdev->name, i2c); @@ -312,13 +313,40 @@ static int __devexit ocores_i2c_remove(struct platform_device* pdev) return 0; } +#ifdef CONFIG_PM +static int ocores_i2c_suspend(struct platform_device *pdev, pm_message_t state) +{ + struct ocores_i2c *i2c = platform_get_drvdata(pdev); + u8 ctrl = oc_getreg(i2c, OCI2C_CONTROL); + + /* make sure the device is disabled */ + oc_setreg(i2c, OCI2C_CONTROL, ctrl & ~(OCI2C_CTRL_EN|OCI2C_CTRL_IEN)); + + return 0; +} + +static int ocores_i2c_resume(struct platform_device *pdev) +{ + struct ocores_i2c *i2c = platform_get_drvdata(pdev); + + ocores_init(i2c); + + return 0; +} +#else +#define ocores_i2c_suspend NULL +#define ocores_i2c_resume NULL +#endif + /* work with hotplug and coldplug */ MODULE_ALIAS("platform:ocores-i2c"); static struct platform_driver ocores_i2c_driver = { - .probe = ocores_i2c_probe, - .remove = __devexit_p(ocores_i2c_remove), - .driver = { + .probe = ocores_i2c_probe, + .remove = __devexit_p(ocores_i2c_remove), + .suspend = ocores_i2c_suspend, + .resume = ocores_i2c_resume, + .driver = { .owner = THIS_MODULE, .name = "ocores-i2c", }, diff --git a/drivers/i2c/busses/i2c-pasemi.c b/drivers/i2c/busses/i2c-pasemi.c index 1603c81e39d4..adf0fbb902f0 100644 --- a/drivers/i2c/busses/i2c-pasemi.c +++ b/drivers/i2c/busses/i2c-pasemi.c @@ -365,7 +365,7 @@ static int __devinit pasemi_smb_probe(struct pci_dev *dev, smbus->adapter.owner = THIS_MODULE; snprintf(smbus->adapter.name, sizeof(smbus->adapter.name), "PA Semi SMBus adapter at 0x%lx", smbus->base); - smbus->adapter.class = I2C_CLASS_HWMON; + smbus->adapter.class = I2C_CLASS_HWMON | I2C_CLASS_SPD; smbus->adapter.algo = &smbus_algorithm; smbus->adapter.algo_data = smbus; smbus->adapter.nr = PCI_FUNC(dev->devfn); diff --git a/drivers/i2c/busses/i2c-pca-platform.c b/drivers/i2c/busses/i2c-pca-platform.c index 9d75f51e8f0e..6bb15ad0a6b6 100644 --- a/drivers/i2c/busses/i2c-pca-platform.c +++ b/drivers/i2c/busses/i2c-pca-platform.c @@ -163,7 +163,7 @@ static int __devinit i2c_pca_pf_probe(struct platform_device *pdev) i2c->reg_base = ioremap(res->start, res_len(res)); if (!i2c->reg_base) { - ret = -EIO; + ret = -ENOMEM; goto e_remap; } i2c->io_base = res->start; diff --git a/drivers/i2c/busses/i2c-piix4.c b/drivers/i2c/busses/i2c-piix4.c index ac9165968587..eaa9b387543e 100644 --- a/drivers/i2c/busses/i2c-piix4.c +++ b/drivers/i2c/busses/i2c-piix4.c @@ -1,6 +1,4 @@ /* - piix4.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring Copyright (c) 1998 - 2002 Frodo Looijaard <frodol@dds.nl> and Philip Edelbrock <phil@netroedge.com> @@ -39,16 +37,10 @@ #include <linux/i2c.h> #include <linux/init.h> #include <linux/dmi.h> +#include <linux/acpi.h> #include <asm/io.h> -struct sd { - const unsigned short mfr; - const unsigned short dev; - const unsigned char fn; - const char *name; -}; - /* PIIX4 SMBus address offsets */ #define SMBHSTSTS (0 + piix4_smba) #define SMBHSLVSTS (1 + piix4_smba) @@ -101,8 +93,6 @@ MODULE_PARM_DESC(force_addr, "Forcibly enable the PIIX4 at the given address. " "EXTREMELY DANGEROUS!"); -static int piix4_transaction(void); - static unsigned short piix4_smba; static int srvrworks_csb5_delay; static struct pci_driver piix4_driver; @@ -141,8 +131,6 @@ static int __devinit piix4_setup(struct pci_dev *PIIX4_dev, { unsigned char temp; - dev_info(&PIIX4_dev->dev, "Found %s device\n", pci_name(PIIX4_dev)); - if ((PIIX4_dev->vendor == PCI_VENDOR_ID_SERVERWORKS) && (PIIX4_dev->device == PCI_DEVICE_ID_SERVERWORKS_CSB5)) srvrworks_csb5_delay = 1; @@ -172,17 +160,20 @@ static int __devinit piix4_setup(struct pci_dev *PIIX4_dev, pci_read_config_word(PIIX4_dev, SMBBA, &piix4_smba); piix4_smba &= 0xfff0; if(piix4_smba == 0) { - dev_err(&PIIX4_dev->dev, "SMB base address " + dev_err(&PIIX4_dev->dev, "SMBus base address " "uninitialized - upgrade BIOS or use " "force_addr=0xaddr\n"); return -ENODEV; } } + if (acpi_check_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) + return -EBUSY; + if (!request_region(piix4_smba, SMBIOSIZE, piix4_driver.name)) { - dev_err(&PIIX4_dev->dev, "SMB region 0x%x already in use!\n", + dev_err(&PIIX4_dev->dev, "SMBus region 0x%x already in use!\n", piix4_smba); - return -ENODEV; + return -EBUSY; } pci_read_config_byte(PIIX4_dev, SMBHSTCFG, &temp); @@ -228,13 +219,13 @@ static int __devinit piix4_setup(struct pci_dev *PIIX4_dev, "(or code out of date)!\n"); pci_read_config_byte(PIIX4_dev, SMBREV, &temp); - dev_dbg(&PIIX4_dev->dev, "SMBREV = 0x%X\n", temp); - dev_dbg(&PIIX4_dev->dev, "SMBA = 0x%X\n", piix4_smba); + dev_info(&PIIX4_dev->dev, + "SMBus Host Controller at 0x%x, revision %d\n", + piix4_smba, temp); return 0; } -/* Another internally used function */ static int piix4_transaction(void) { int temp; @@ -253,7 +244,7 @@ static int piix4_transaction(void) outb_p(temp, SMBHSTSTS); if ((temp = inb_p(SMBHSTSTS)) != 0x00) { dev_err(&piix4_adapter.dev, "Failed! (%02x)\n", temp); - return -1; + return -EBUSY; } else { dev_dbg(&piix4_adapter.dev, "Successful!\n"); } @@ -275,23 +266,23 @@ static int piix4_transaction(void) /* If the SMBus is still busy, we give up */ if (timeout >= MAX_TIMEOUT) { dev_err(&piix4_adapter.dev, "SMBus Timeout!\n"); - result = -1; + result = -ETIMEDOUT; } if (temp & 0x10) { - result = -1; + result = -EIO; dev_err(&piix4_adapter.dev, "Error: Failed bus transaction\n"); } if (temp & 0x08) { - result = -1; + result = -EIO; dev_dbg(&piix4_adapter.dev, "Bus collision! SMBus may be " "locked until next hard reset. (sorry!)\n"); /* Clock stops and slave is stuck in mid-transmission */ } if (temp & 0x04) { - result = -1; + result = -ENXIO; dev_dbg(&piix4_adapter.dev, "Error: no response!\n"); } @@ -309,31 +300,29 @@ static int piix4_transaction(void) return result; } -/* Return -1 on error. */ +/* Return negative errno on error. */ static s32 piix4_access(struct i2c_adapter * adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data * data) { int i, len; + int status; switch (size) { - case I2C_SMBUS_PROC_CALL: - dev_err(&adap->dev, "I2C_SMBUS_PROC_CALL not supported!\n"); - return -1; case I2C_SMBUS_QUICK: - outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), + outb_p((addr << 1) | read_write, SMBHSTADD); size = PIIX4_QUICK; break; case I2C_SMBUS_BYTE: - outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), + outb_p((addr << 1) | read_write, SMBHSTADD); if (read_write == I2C_SMBUS_WRITE) outb_p(command, SMBHSTCMD); size = PIIX4_BYTE; break; case I2C_SMBUS_BYTE_DATA: - outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), + outb_p((addr << 1) | read_write, SMBHSTADD); outb_p(command, SMBHSTCMD); if (read_write == I2C_SMBUS_WRITE) @@ -341,7 +330,7 @@ static s32 piix4_access(struct i2c_adapter * adap, u16 addr, size = PIIX4_BYTE_DATA; break; case I2C_SMBUS_WORD_DATA: - outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), + outb_p((addr << 1) | read_write, SMBHSTADD); outb_p(command, SMBHSTCMD); if (read_write == I2C_SMBUS_WRITE) { @@ -351,15 +340,13 @@ static s32 piix4_access(struct i2c_adapter * adap, u16 addr, size = PIIX4_WORD_DATA; break; case I2C_SMBUS_BLOCK_DATA: - outb_p(((addr & 0x7f) << 1) | (read_write & 0x01), + outb_p((addr << 1) | read_write, SMBHSTADD); outb_p(command, SMBHSTCMD); if (read_write == I2C_SMBUS_WRITE) { len = data->block[0]; - if (len < 0) - len = 0; - if (len > 32) - len = 32; + if (len == 0 || len > I2C_SMBUS_BLOCK_MAX) + return -EINVAL; outb_p(len, SMBHSTDAT0); i = inb_p(SMBHSTCNT); /* Reset SMBBLKDAT */ for (i = 1; i <= len; i++) @@ -367,12 +354,16 @@ static s32 piix4_access(struct i2c_adapter * adap, u16 addr, } size = PIIX4_BLOCK_DATA; break; + default: + dev_warn(&adap->dev, "Unsupported transaction %d\n", size); + return -EOPNOTSUPP; } outb_p((size & 0x1C) + (ENABLE_INT9 & 1), SMBHSTCNT); - if (piix4_transaction()) /* Error in transaction */ - return -1; + status = piix4_transaction(); + if (status) + return status; if ((read_write == I2C_SMBUS_WRITE) || (size == PIIX4_QUICK)) return 0; @@ -388,6 +379,8 @@ static s32 piix4_access(struct i2c_adapter * adap, u16 addr, break; case PIIX4_BLOCK_DATA: data->block[0] = inb_p(SMBHSTDAT0); + if (data->block[0] == 0 || data->block[0] > I2C_SMBUS_BLOCK_MAX) + return -EPROTO; i = inb_p(SMBHSTCNT); /* Reset SMBBLKDAT */ for (i = 1; i <= data->block[0]; i++) data->block[i] = inb_p(SMBBLKDAT); @@ -411,7 +404,7 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter piix4_adapter = { .owner = THIS_MODULE, .id = I2C_HW_SMBUS_PIIX4, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-pmcmsp.c b/drivers/i2c/busses/i2c-pmcmsp.c index 63b3e2c11cff..dcf2045b5222 100644 --- a/drivers/i2c/busses/i2c-pmcmsp.c +++ b/drivers/i2c/busses/i2c-pmcmsp.c @@ -622,7 +622,7 @@ static struct i2c_algorithm pmcmsptwi_algo = { static struct i2c_adapter pmcmsptwi_adapter = { .owner = THIS_MODULE, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &pmcmsptwi_algo, .name = DRV_NAME, }; diff --git a/drivers/i2c/busses/i2c-prosavage.c b/drivers/i2c/busses/i2c-prosavage.c deleted file mode 100644 index 07c1f1e27df1..000000000000 --- a/drivers/i2c/busses/i2c-prosavage.c +++ /dev/null @@ -1,325 +0,0 @@ -/* - * kernel/busses/i2c-prosavage.c - * - * i2c bus driver for S3/VIA 8365/8375 graphics processor. - * Copyright (c) 2003 Henk Vergonet <henk@god.dyndns.org> - * Based on code written by: - * Frodo Looijaard <frodol@dds.nl>, - * Philip Edelbrock <phil@netroedge.com>, - * Ralph Metzler <rjkm@thp.uni-koeln.de>, and - * Mark D. Studebaker <mdsxyz123@yahoo.com> - * Simon Vogl - * and others - * - * Please read the lm_sensors documentation for details on use. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - * - */ -/* 18-05-2003 HVE - created - * 14-06-2003 HVE - adapted for lm_sensors2 - * 17-06-2003 HVE - linux 2.5.xx compatible - * 18-06-2003 HVE - codingstyle - * 21-06-2003 HVE - compatibility lm_sensors2 and linux 2.5.xx - * codingstyle, mmio enabled - * - * This driver interfaces to the I2C bus of the VIA north bridge embedded - * ProSavage4/8 devices. Usefull for gaining access to the TV Encoder chips. - * - * Graphics cores: - * S3/VIA KM266/VT8375 aka ProSavage8 - * S3/VIA KM133/VT8365 aka Savage4 - * - * Two serial busses are implemented: - * SERIAL1 - I2C serial communications interface - * SERIAL2 - DDC2 monitor communications interface - * - * Tested on a FX41 mainboard, see http://www.shuttle.com - * - * - * TODO: - * - integration with prosavage framebuffer device - * (Additional documentation needed :( - */ - -#include <linux/module.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/i2c.h> -#include <linux/i2c-algo-bit.h> -#include <asm/io.h> - -/* - * driver configuration - */ -#define MAX_BUSSES 2 - -struct s_i2c_bus { - void __iomem *mmvga; - int i2c_reg; - int adap_ok; - struct i2c_adapter adap; - struct i2c_algo_bit_data algo; -}; - -struct s_i2c_chip { - void __iomem *mmio; - struct s_i2c_bus i2c_bus[MAX_BUSSES]; -}; - - -/* - * i2c configuration - */ -#define CYCLE_DELAY 10 -#define TIMEOUT (HZ / 2) - - -/* - * S3/VIA 8365/8375 registers - */ -#define VGA_CR_IX 0x3d4 -#define VGA_CR_DATA 0x3d5 - -#define CR_SERIAL1 0xa0 /* I2C serial communications interface */ -#define MM_SERIAL1 0xff20 -#define CR_SERIAL2 0xb1 /* DDC2 monitor communications interface */ - -/* based on vt8365 documentation */ -#define I2C_ENAB 0x10 -#define I2C_SCL_OUT 0x01 -#define I2C_SDA_OUT 0x02 -#define I2C_SCL_IN 0x04 -#define I2C_SDA_IN 0x08 - -#define SET_CR_IX(p, val) writeb((val), (p)->mmvga + VGA_CR_IX) -#define SET_CR_DATA(p, val) writeb((val), (p)->mmvga + VGA_CR_DATA) -#define GET_CR_DATA(p) readb((p)->mmvga + VGA_CR_DATA) - - -/* - * Serial bus line handling - * - * serial communications register as parameter in private data - * - * TODO: locks with other code sections accessing video registers? - */ -static void bit_s3via_setscl(void *bus, int val) -{ - struct s_i2c_bus *p = (struct s_i2c_bus *)bus; - unsigned int r; - - SET_CR_IX(p, p->i2c_reg); - r = GET_CR_DATA(p); - r |= I2C_ENAB; - if (val) { - r |= I2C_SCL_OUT; - } else { - r &= ~I2C_SCL_OUT; - } - SET_CR_DATA(p, r); -} - -static void bit_s3via_setsda(void *bus, int val) -{ - struct s_i2c_bus *p = (struct s_i2c_bus *)bus; - unsigned int r; - - SET_CR_IX(p, p->i2c_reg); - r = GET_CR_DATA(p); - r |= I2C_ENAB; - if (val) { - r |= I2C_SDA_OUT; - } else { - r &= ~I2C_SDA_OUT; - } - SET_CR_DATA(p, r); -} - -static int bit_s3via_getscl(void *bus) -{ - struct s_i2c_bus *p = (struct s_i2c_bus *)bus; - - SET_CR_IX(p, p->i2c_reg); - return (0 != (GET_CR_DATA(p) & I2C_SCL_IN)); -} - -static int bit_s3via_getsda(void *bus) -{ - struct s_i2c_bus *p = (struct s_i2c_bus *)bus; - - SET_CR_IX(p, p->i2c_reg); - return (0 != (GET_CR_DATA(p) & I2C_SDA_IN)); -} - - -/* - * adapter initialisation - */ -static int i2c_register_bus(struct pci_dev *dev, struct s_i2c_bus *p, void __iomem *mmvga, u32 i2c_reg) -{ - int ret; - p->adap.owner = THIS_MODULE; - p->adap.id = I2C_HW_B_S3VIA; - p->adap.algo_data = &p->algo; - p->adap.dev.parent = &dev->dev; - p->algo.setsda = bit_s3via_setsda; - p->algo.setscl = bit_s3via_setscl; - p->algo.getsda = bit_s3via_getsda; - p->algo.getscl = bit_s3via_getscl; - p->algo.udelay = CYCLE_DELAY; - p->algo.timeout = TIMEOUT; - p->algo.data = p; - p->mmvga = mmvga; - p->i2c_reg = i2c_reg; - - ret = i2c_bit_add_bus(&p->adap); - if (ret) { - return ret; - } - - p->adap_ok = 1; - return 0; -} - - -/* - * Cleanup stuff - */ -static void prosavage_remove(struct pci_dev *dev) -{ - struct s_i2c_chip *chip; - int i, ret; - - chip = (struct s_i2c_chip *)pci_get_drvdata(dev); - - if (!chip) { - return; - } - for (i = MAX_BUSSES - 1; i >= 0; i--) { - if (chip->i2c_bus[i].adap_ok == 0) - continue; - - ret = i2c_del_adapter(&chip->i2c_bus[i].adap); - if (ret) { - dev_err(&dev->dev, "%s not removed\n", - chip->i2c_bus[i].adap.name); - } - } - if (chip->mmio) { - iounmap(chip->mmio); - } - kfree(chip); -} - - -/* - * Detect chip and initialize it - */ -static int __devinit prosavage_probe(struct pci_dev *dev, const struct pci_device_id *id) -{ - int ret; - unsigned long base, len; - struct s_i2c_chip *chip; - struct s_i2c_bus *bus; - - pci_set_drvdata(dev, kzalloc(sizeof(struct s_i2c_chip), GFP_KERNEL)); - chip = (struct s_i2c_chip *)pci_get_drvdata(dev); - if (chip == NULL) { - return -ENOMEM; - } - - base = dev->resource[0].start & PCI_BASE_ADDRESS_MEM_MASK; - len = dev->resource[0].end - base + 1; - chip->mmio = ioremap_nocache(base, len); - - if (chip->mmio == NULL) { - dev_err(&dev->dev, "ioremap failed\n"); - prosavage_remove(dev); - return -ENODEV; - } - - - /* - * Chip initialisation - */ - /* Unlock Extended IO Space ??? */ - - - /* - * i2c bus registration - */ - bus = &chip->i2c_bus[0]; - snprintf(bus->adap.name, sizeof(bus->adap.name), - "ProSavage I2C bus at %02x:%02x.%x", - dev->bus->number, PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn)); - ret = i2c_register_bus(dev, bus, chip->mmio + 0x8000, CR_SERIAL1); - if (ret) { - goto err_adap; - } - /* - * ddc bus registration - */ - bus = &chip->i2c_bus[1]; - snprintf(bus->adap.name, sizeof(bus->adap.name), - "ProSavage DDC bus at %02x:%02x.%x", - dev->bus->number, PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn)); - ret = i2c_register_bus(dev, bus, chip->mmio + 0x8000, CR_SERIAL2); - if (ret) { - goto err_adap; - } - return 0; -err_adap: - dev_err(&dev->dev, "%s failed\n", bus->adap.name); - prosavage_remove(dev); - return ret; -} - - -/* - * Data for PCI driver interface - */ -static struct pci_device_id prosavage_pci_tbl[] = { - { PCI_DEVICE(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_SAVAGE4) }, - { PCI_DEVICE(PCI_VENDOR_ID_S3, PCI_DEVICE_ID_S3_PROSAVAGE8) }, - { 0, }, -}; - -MODULE_DEVICE_TABLE (pci, prosavage_pci_tbl); - -static struct pci_driver prosavage_driver = { - .name = "prosavage_smbus", - .id_table = prosavage_pci_tbl, - .probe = prosavage_probe, - .remove = prosavage_remove, -}; - -static int __init i2c_prosavage_init(void) -{ - return pci_register_driver(&prosavage_driver); -} - -static void __exit i2c_prosavage_exit(void) -{ - pci_unregister_driver(&prosavage_driver); -} - -MODULE_DEVICE_TABLE(pci, prosavage_pci_tbl); -MODULE_AUTHOR("Henk Vergonet"); -MODULE_DESCRIPTION("ProSavage VIA 8365/8375 smbus driver"); -MODULE_LICENSE("GPL"); - -module_init (i2c_prosavage_init); -module_exit (i2c_prosavage_exit); diff --git a/drivers/i2c/busses/i2c-pxa.c b/drivers/i2c/busses/i2c-pxa.c index eb69fbadc9cb..af9e6034d7fb 100644 --- a/drivers/i2c/busses/i2c-pxa.c +++ b/drivers/i2c/busses/i2c-pxa.c @@ -39,7 +39,6 @@ #include <asm/io.h> #include <asm/arch/i2c.h> #include <asm/arch/pxa-regs.h> -#include <asm/arch/pxa2xx-gpio.h> struct pxa_i2c { spinlock_t lock; @@ -945,32 +944,6 @@ static const struct i2c_algorithm i2c_pxa_pio_algorithm = { .functionality = i2c_pxa_functionality, }; -static void i2c_pxa_enable(struct platform_device *dev) -{ - if (cpu_is_pxa27x()) { - switch (dev->id) { - case 0: - pxa_gpio_mode(GPIO117_I2CSCL_MD); - pxa_gpio_mode(GPIO118_I2CSDA_MD); - break; - case 1: - local_irq_disable(); - PCFR |= PCFR_PI2CEN; - local_irq_enable(); - break; - } - } -} - -static void i2c_pxa_disable(struct platform_device *dev) -{ - if (cpu_is_pxa27x() && dev->id == 1) { - local_irq_disable(); - PCFR &= ~PCFR_PI2CEN; - local_irq_enable(); - } -} - #define res_len(r) ((r)->end - (r)->start + 1) static int i2c_pxa_probe(struct platform_device *dev) { @@ -1036,7 +1009,6 @@ static int i2c_pxa_probe(struct platform_device *dev) #endif clk_enable(i2c->clk); - i2c_pxa_enable(dev); if (plat) { i2c->adap.class = plat->class; @@ -1080,7 +1052,6 @@ eadapt: free_irq(irq, i2c); ereqirq: clk_disable(i2c->clk); - i2c_pxa_disable(dev); iounmap(i2c->reg_base); eremap: clk_put(i2c->clk); @@ -1103,7 +1074,6 @@ static int __exit i2c_pxa_remove(struct platform_device *dev) clk_disable(i2c->clk); clk_put(i2c->clk); - i2c_pxa_disable(dev); iounmap(i2c->reg_base); release_mem_region(i2c->iobase, i2c->iosize); @@ -1134,5 +1104,5 @@ static void __exit i2c_adap_pxa_exit(void) MODULE_LICENSE("GPL"); MODULE_ALIAS("platform:pxa2xx-i2c"); -module_init(i2c_adap_pxa_init); +subsys_initcall(i2c_adap_pxa_init); module_exit(i2c_adap_pxa_exit); diff --git a/drivers/i2c/busses/i2c-s3c2410.c b/drivers/i2c/busses/i2c-s3c2410.c index 1305ef190fc1..007390ad9810 100644 --- a/drivers/i2c/busses/i2c-s3c2410.c +++ b/drivers/i2c/busses/i2c-s3c2410.c @@ -290,12 +290,12 @@ static int i2s_s3c_irq_nextbyte(struct s3c24xx_i2c *i2c, unsigned long iicstat) * bus, or started a new i2c message */ - if (iicstat & S3C2410_IICSTAT_LASTBIT && + if (iicstat & S3C2410_IICSTAT_LASTBIT && !(i2c->msg->flags & I2C_M_IGNORE_NAK)) { /* ack was not received... */ dev_dbg(i2c->dev, "ack was not received\n"); - s3c24xx_i2c_stop(i2c, -EREMOTEIO); + s3c24xx_i2c_stop(i2c, -ENXIO); goto out_ack; } @@ -305,7 +305,7 @@ static int i2s_s3c_irq_nextbyte(struct s3c24xx_i2c *i2c, unsigned long iicstat) i2c->state = STATE_WRITE; /* terminate the transfer if there is nothing to do - * (used by the i2c probe to find devices */ + * as this is used by the i2c probe to find devices. */ if (is_lastmsg(i2c) && i2c->msg->len == 0) { s3c24xx_i2c_stop(i2c, 0); @@ -323,7 +323,17 @@ static int i2s_s3c_irq_nextbyte(struct s3c24xx_i2c *i2c, unsigned long iicstat) * end of the message, and if so, work out what to do */ + if (!(i2c->msg->flags & I2C_M_IGNORE_NAK)) { + if (iicstat & S3C2410_IICSTAT_LASTBIT) { + dev_dbg(i2c->dev, "WRITE: No Ack\n"); + + s3c24xx_i2c_stop(i2c, -ECONNREFUSED); + goto out_ack; + } + } + retry_write: + if (!is_msgend(i2c)) { byte = i2c->msg->buf[i2c->msg_ptr++]; writeb(byte, i2c->regs + S3C2410_IICDS); @@ -377,17 +387,6 @@ static int i2s_s3c_irq_nextbyte(struct s3c24xx_i2c *i2c, unsigned long iicstat) * going to do any more read/write */ - if (!(i2c->msg->flags & I2C_M_IGNORE_NAK) && - !(is_msglast(i2c) && is_lastmsg(i2c))) { - - if (iicstat & S3C2410_IICSTAT_LASTBIT) { - dev_dbg(i2c->dev, "READ: No Ack\n"); - - s3c24xx_i2c_stop(i2c, -ECONNREFUSED); - goto out_ack; - } - } - byte = readb(i2c->regs + S3C2410_IICDS); i2c->msg->buf[i2c->msg_ptr++] = byte; @@ -591,7 +590,7 @@ static struct s3c24xx_i2c s3c24xx_i2c = { .owner = THIS_MODULE, .algo = &s3c24xx_i2c_algorithm, .retries = 2, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, }, }; @@ -949,3 +948,4 @@ MODULE_DESCRIPTION("S3C24XX I2C Bus driver"); MODULE_AUTHOR("Ben Dooks, <ben@simtec.co.uk>"); MODULE_LICENSE("GPL"); MODULE_ALIAS("platform:s3c2410-i2c"); +MODULE_ALIAS("platform:s3c2440-i2c"); diff --git a/drivers/i2c/busses/i2c-savage4.c b/drivers/i2c/busses/i2c-savage4.c deleted file mode 100644 index 8adf4abaa035..000000000000 --- a/drivers/i2c/busses/i2c-savage4.c +++ /dev/null @@ -1,185 +0,0 @@ -/* - i2c-savage4.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring - Copyright (C) 1998-2003 The LM Sensors Team - Alexander Wold <awold@bigfoot.com> - Mark D. Studebaker <mdsxyz123@yahoo.com> - - Based on i2c-voodoo3.c. - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. -*/ - -/* This interfaces to the I2C bus of the Savage4 to gain access to - the BT869 and possibly other I2C devices. The DDC bus is not - yet supported because its register is not memory-mapped. -*/ - -#include <linux/kernel.h> -#include <linux/module.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/i2c.h> -#include <linux/i2c-algo-bit.h> -#include <asm/io.h> - -/* device IDs */ -#define PCI_CHIP_SAVAGE4 0x8A22 -#define PCI_CHIP_SAVAGE2000 0x9102 - -#define REG 0xff20 /* Serial Port 1 Register */ - -/* bit locations in the register */ -#define I2C_ENAB 0x00000020 -#define I2C_SCL_OUT 0x00000001 -#define I2C_SDA_OUT 0x00000002 -#define I2C_SCL_IN 0x00000008 -#define I2C_SDA_IN 0x00000010 - -/* delays */ -#define CYCLE_DELAY 10 -#define TIMEOUT (HZ / 2) - - -static void __iomem *ioaddr; - -/* The sav GPIO registers don't have individual masks for each bit - so we always have to read before writing. */ - -static void bit_savi2c_setscl(void *data, int val) -{ - unsigned int r; - r = readl(ioaddr + REG); - if(val) - r |= I2C_SCL_OUT; - else - r &= ~I2C_SCL_OUT; - writel(r, ioaddr + REG); - readl(ioaddr + REG); /* flush posted write */ -} - -static void bit_savi2c_setsda(void *data, int val) -{ - unsigned int r; - r = readl(ioaddr + REG); - if(val) - r |= I2C_SDA_OUT; - else - r &= ~I2C_SDA_OUT; - writel(r, ioaddr + REG); - readl(ioaddr + REG); /* flush posted write */ -} - -/* The GPIO pins are open drain, so the pins always remain outputs. - We rely on the i2c-algo-bit routines to set the pins high before - reading the input from other chips. */ - -static int bit_savi2c_getscl(void *data) -{ - return (0 != (readl(ioaddr + REG) & I2C_SCL_IN)); -} - -static int bit_savi2c_getsda(void *data) -{ - return (0 != (readl(ioaddr + REG) & I2C_SDA_IN)); -} - -/* Configures the chip */ - -static int config_s4(struct pci_dev *dev) -{ - unsigned long cadr; - - /* map memory */ - cadr = dev->resource[0].start; - cadr &= PCI_BASE_ADDRESS_MEM_MASK; - ioaddr = ioremap_nocache(cadr, 0x0080000); - if (ioaddr) { - /* writel(0x8160, ioaddr + REG2); */ - writel(0x00000020, ioaddr + REG); - dev_info(&dev->dev, "Using Savage4 at %p\n", ioaddr); - return 0; - } - return -ENODEV; -} - -static struct i2c_algo_bit_data sav_i2c_bit_data = { - .setsda = bit_savi2c_setsda, - .setscl = bit_savi2c_setscl, - .getsda = bit_savi2c_getsda, - .getscl = bit_savi2c_getscl, - .udelay = CYCLE_DELAY, - .timeout = TIMEOUT -}; - -static struct i2c_adapter savage4_i2c_adapter = { - .owner = THIS_MODULE, - .id = I2C_HW_B_SAVAGE, - .name = "I2C Savage4 adapter", - .algo_data = &sav_i2c_bit_data, -}; - -static struct pci_device_id savage4_ids[] __devinitdata = { - { PCI_DEVICE(PCI_VENDOR_ID_S3, PCI_CHIP_SAVAGE4) }, - { PCI_DEVICE(PCI_VENDOR_ID_S3, PCI_CHIP_SAVAGE2000) }, - { 0, } -}; - -MODULE_DEVICE_TABLE (pci, savage4_ids); - -static int __devinit savage4_probe(struct pci_dev *dev, const struct pci_device_id *id) -{ - int retval; - - retval = config_s4(dev); - if (retval) - return retval; - - /* set up the sysfs linkage to our parent device */ - savage4_i2c_adapter.dev.parent = &dev->dev; - - return i2c_bit_add_bus(&savage4_i2c_adapter); -} - -static void __devexit savage4_remove(struct pci_dev *dev) -{ - i2c_del_adapter(&savage4_i2c_adapter); - iounmap(ioaddr); -} - -static struct pci_driver savage4_driver = { - .name = "savage4_smbus", - .id_table = savage4_ids, - .probe = savage4_probe, - .remove = __devexit_p(savage4_remove), -}; - -static int __init i2c_savage4_init(void) -{ - return pci_register_driver(&savage4_driver); -} - -static void __exit i2c_savage4_exit(void) -{ - pci_unregister_driver(&savage4_driver); -} - -MODULE_AUTHOR("Alexander Wold <awold@bigfoot.com> " - "and Mark D. Studebaker <mdsxyz123@yahoo.com>"); -MODULE_DESCRIPTION("Savage4 I2C/SMBus driver"); -MODULE_LICENSE("GPL"); - -module_init(i2c_savage4_init); -module_exit(i2c_savage4_exit); diff --git a/drivers/i2c/busses/i2c-sibyte.c b/drivers/i2c/busses/i2c-sibyte.c index 114634da6c6e..4ddefbf238e9 100644 --- a/drivers/i2c/busses/i2c-sibyte.c +++ b/drivers/i2c/busses/i2c-sibyte.c @@ -143,7 +143,7 @@ static int __init i2c_sibyte_add_bus(struct i2c_adapter *i2c_adap, int speed) csr_out32(speed, SMB_CSR(adap,R_SMB_FREQ)); csr_out32(0, SMB_CSR(adap,R_SMB_CONTROL)); - return i2c_add_adapter(i2c_adap); + return i2c_add_numbered_adapter(i2c_adap); } @@ -156,17 +156,19 @@ static struct i2c_adapter sibyte_board_adapter[2] = { { .owner = THIS_MODULE, .id = I2C_HW_SIBYTE, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = NULL, .algo_data = &sibyte_board_data[0], + .nr = 0, .name = "SiByte SMBus 0", }, { .owner = THIS_MODULE, .id = I2C_HW_SIBYTE, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = NULL, .algo_data = &sibyte_board_data[1], + .nr = 1, .name = "SiByte SMBus 1", }, }; diff --git a/drivers/i2c/busses/i2c-sis5595.c b/drivers/i2c/busses/i2c-sis5595.c index 9ca8f9155f95..dfc2d5eb6a68 100644 --- a/drivers/i2c/busses/i2c-sis5595.c +++ b/drivers/i2c/busses/i2c-sis5595.c @@ -1,6 +1,4 @@ /* - sis5595.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring Copyright (c) 1998, 1999 Frodo Looijaard <frodol@dds.nl> and Philip Edelbrock <phil@netroedge.com> @@ -62,6 +60,7 @@ #include <linux/ioport.h> #include <linux/init.h> #include <linux/i2c.h> +#include <linux/acpi.h> #include <asm/io.h> static int blacklist[] = { @@ -174,6 +173,11 @@ static int sis5595_setup(struct pci_dev *SIS5595_dev) /* NB: We grab just the two SMBus registers here, but this may still * interfere with ACPI :-( */ + retval = acpi_check_region(sis5595_base + SMB_INDEX, 2, + sis5595_driver.name); + if (retval) + return retval; + if (!request_region(sis5595_base + SMB_INDEX, 2, sis5595_driver.name)) { dev_err(&SIS5595_dev->dev, "SMBus registers 0x%04x-0x%04x already in use!\n", @@ -236,7 +240,7 @@ static int sis5595_transaction(struct i2c_adapter *adap) sis5595_write(SMB_STS_HI, temp >> 8); if ((temp = sis5595_read(SMB_STS_LO) + (sis5595_read(SMB_STS_HI) << 8)) != 0x00) { dev_dbg(&adap->dev, "Failed! (%02x)\n", temp); - return -1; + return -EBUSY; } else { dev_dbg(&adap->dev, "Successful!\n"); } @@ -254,19 +258,19 @@ static int sis5595_transaction(struct i2c_adapter *adap) /* If the SMBus is still busy, we give up */ if (timeout >= MAX_TIMEOUT) { dev_dbg(&adap->dev, "SMBus Timeout!\n"); - result = -1; + result = -ETIMEDOUT; } if (temp & 0x10) { dev_dbg(&adap->dev, "Error: Failed bus transaction\n"); - result = -1; + result = -ENXIO; } if (temp & 0x20) { dev_err(&adap->dev, "Bus collision! SMBus may be locked until " "next hard reset (or not...)\n"); /* Clock stops and slave is stuck in mid-transmission */ - result = -1; + result = -EIO; } temp = sis5595_read(SMB_STS_LO) + (sis5595_read(SMB_STS_HI) << 8); @@ -282,11 +286,13 @@ static int sis5595_transaction(struct i2c_adapter *adap) return result; } -/* Return -1 on error. */ +/* Return negative errno on error. */ static s32 sis5595_access(struct i2c_adapter *adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data *data) { + int status; + switch (size) { case I2C_SMBUS_QUICK: sis5595_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01)); @@ -318,13 +324,14 @@ static s32 sis5595_access(struct i2c_adapter *adap, u16 addr, break; default: dev_warn(&adap->dev, "Unsupported transaction %d\n", size); - return -1; + return -EOPNOTSUPP; } sis5595_write(SMB_CTL_LO, ((size & 0x0E))); - if (sis5595_transaction(adap)) - return -1; + status = sis5595_transaction(adap); + if (status) + return status; if ((size != SIS5595_PROC_CALL) && ((read_write == I2C_SMBUS_WRITE) || (size == SIS5595_QUICK))) @@ -359,7 +366,7 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter sis5595_adapter = { .owner = THIS_MODULE, .id = I2C_HW_SMBUS_SIS5595, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-sis630.c b/drivers/i2c/busses/i2c-sis630.c index 3765dd7f450f..e7c4b790da54 100644 --- a/drivers/i2c/busses/i2c-sis630.c +++ b/drivers/i2c/busses/i2c-sis630.c @@ -1,7 +1,4 @@ /* - i2c-sis630.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring - Copyright (c) 2002,2003 Alexander Malysh <amalysh@web.de> This program is free software; you can redistribute it and/or modify @@ -55,6 +52,7 @@ #include <linux/ioport.h> #include <linux/init.h> #include <linux/i2c.h> +#include <linux/acpi.h> #include <asm/io.h> /* SIS630 SMBus registers */ @@ -134,7 +132,7 @@ static int sis630_transaction_start(struct i2c_adapter *adap, int size, u8 *oldc if ((temp = sis630_read(SMB_CNT) & 0x03) != 0x00) { dev_dbg(&adap->dev, "Failed! (%02x)\n", temp); - return -1; + return -EBUSY; } else { dev_dbg(&adap->dev, "Successful!\n"); } @@ -177,17 +175,17 @@ static int sis630_transaction_wait(struct i2c_adapter *adap, int size) /* If the SMBus is still busy, we give up */ if (timeout >= MAX_TIMEOUT) { dev_dbg(&adap->dev, "SMBus Timeout!\n"); - result = -1; + result = -ETIMEDOUT; } if (temp & 0x02) { dev_dbg(&adap->dev, "Error: Failed bus transaction\n"); - result = -1; + result = -ENXIO; } if (temp & 0x04) { dev_err(&adap->dev, "Bus collision!\n"); - result = -1; + result = -EIO; /* TBD: Datasheet say: the software should clear this bit and restart SMBUS operation. @@ -250,8 +248,10 @@ static int sis630_block_data(struct i2c_adapter *adap, union i2c_smbus_data *dat if (i==8 || (len<8 && i==len)) { dev_dbg(&adap->dev, "start trans len=%d i=%d\n",len ,i); /* first transaction */ - if (sis630_transaction_start(adap, SIS630_BLOCK_DATA, &oldclock)) - return -1; + rc = sis630_transaction_start(adap, + SIS630_BLOCK_DATA, &oldclock); + if (rc) + return rc; } else if ((i-1)%8 == 7 || i==len) { dev_dbg(&adap->dev, "trans_wait len=%d i=%d\n",len,i); @@ -264,9 +264,10 @@ static int sis630_block_data(struct i2c_adapter *adap, union i2c_smbus_data *dat */ sis630_write(SMB_STS,0x10); } - if (sis630_transaction_wait(adap, SIS630_BLOCK_DATA)) { + rc = sis630_transaction_wait(adap, + SIS630_BLOCK_DATA); + if (rc) { dev_dbg(&adap->dev, "trans_wait failed\n"); - rc = -1; break; } } @@ -275,13 +276,14 @@ static int sis630_block_data(struct i2c_adapter *adap, union i2c_smbus_data *dat else { /* read request */ data->block[0] = len = 0; - if (sis630_transaction_start(adap, SIS630_BLOCK_DATA, &oldclock)) { - return -1; - } + rc = sis630_transaction_start(adap, + SIS630_BLOCK_DATA, &oldclock); + if (rc) + return rc; do { - if (sis630_transaction_wait(adap, SIS630_BLOCK_DATA)) { + rc = sis630_transaction_wait(adap, SIS630_BLOCK_DATA); + if (rc) { dev_dbg(&adap->dev, "trans_wait failed\n"); - rc = -1; break; } /* if this first transaction then read byte count */ @@ -311,11 +313,13 @@ static int sis630_block_data(struct i2c_adapter *adap, union i2c_smbus_data *dat return rc; } -/* Return -1 on error. */ +/* Return negative errno on error. */ static s32 sis630_access(struct i2c_adapter *adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data *data) { + int status; + switch (size) { case I2C_SMBUS_QUICK: sis630_write(SMB_ADDR, ((addr & 0x7f) << 1) | (read_write & 0x01)); @@ -350,13 +354,14 @@ static s32 sis630_access(struct i2c_adapter *adap, u16 addr, size = SIS630_BLOCK_DATA; return sis630_block_data(adap, data, read_write); default: - printk("Unsupported I2C size\n"); - return -1; - break; + dev_warn(&adap->dev, "Unsupported transaction %d\n", + size); + return -EOPNOTSUPP; } - if (sis630_transaction(adap, size)) - return -1; + status = sis630_transaction(adap, size); + if (status) + return status; if ((size != SIS630_PCALL) && ((read_write == I2C_SMBUS_WRITE) || (size == SIS630_QUICK))) { @@ -372,9 +377,6 @@ static s32 sis630_access(struct i2c_adapter *adap, u16 addr, case SIS630_WORD_DATA: data->word = sis630_read(SMB_BYTE) + (sis630_read(SMB_BYTE + 1) << 8); break; - default: - return -1; - break; } return 0; @@ -433,6 +435,11 @@ static int sis630_setup(struct pci_dev *sis630_dev) dev_dbg(&sis630_dev->dev, "ACPI base at 0x%04x\n", acpi_base); + retval = acpi_check_region(acpi_base + SMB_STS, SIS630_SMB_IOREGION, + sis630_driver.name); + if (retval) + goto exit; + /* Everything is happy, let's grab the memory and set things up. */ if (!request_region(acpi_base + SMB_STS, SIS630_SMB_IOREGION, sis630_driver.name)) { @@ -458,7 +465,7 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter sis630_adapter = { .owner = THIS_MODULE, .id = I2C_HW_SMBUS_SIS630, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; diff --git a/drivers/i2c/busses/i2c-sis96x.c b/drivers/i2c/busses/i2c-sis96x.c index dc235bb8e24d..f1bba6396641 100644 --- a/drivers/i2c/busses/i2c-sis96x.c +++ b/drivers/i2c/busses/i2c-sis96x.c @@ -1,7 +1,4 @@ /* - sis96x.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring - Copyright (c) 2003 Mark M. Hoffman <mhoffman@lightlink.com> This program is free software; you can redistribute it and/or modify @@ -40,6 +37,7 @@ #include <linux/ioport.h> #include <linux/i2c.h> #include <linux/init.h> +#include <linux/acpi.h> #include <asm/io.h> /* base address register in PCI config space */ @@ -111,7 +109,7 @@ static int sis96x_transaction(int size) /* check it again */ if (((temp = sis96x_read(SMB_CNT)) & 0x03) != 0x00) { dev_dbg(&sis96x_adapter.dev, "Failed (0x%02x)\n", temp); - return -1; + return -EBUSY; } else { dev_dbg(&sis96x_adapter.dev, "Successful\n"); } @@ -136,19 +134,19 @@ static int sis96x_transaction(int size) /* If the SMBus is still busy, we give up */ if (timeout >= MAX_TIMEOUT) { dev_dbg(&sis96x_adapter.dev, "SMBus Timeout! (0x%02x)\n", temp); - result = -1; + result = -ETIMEDOUT; } /* device error - probably missing ACK */ if (temp & 0x02) { dev_dbg(&sis96x_adapter.dev, "Failed bus transaction!\n"); - result = -1; + result = -ENXIO; } /* bus collision */ if (temp & 0x04) { dev_dbg(&sis96x_adapter.dev, "Bus collision!\n"); - result = -1; + result = -EIO; } /* Finish up by resetting the bus */ @@ -161,11 +159,12 @@ static int sis96x_transaction(int size) return result; } -/* Return -1 on error. */ +/* Return negative errno on error. */ static s32 sis96x_access(struct i2c_adapter * adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data * data) { + int status; switch (size) { case I2C_SMBUS_QUICK: @@ -200,20 +199,14 @@ static s32 sis96x_access(struct i2c_adapter * adap, u16 addr, SIS96x_PROC_CALL : SIS96x_WORD_DATA); break; - case I2C_SMBUS_BLOCK_DATA: - /* TO DO: */ - dev_info(&adap->dev, "SMBus block not implemented!\n"); - return -1; - break; - default: - dev_info(&adap->dev, "Unsupported I2C size\n"); - return -1; - break; + dev_warn(&adap->dev, "Unsupported transaction %d\n", size); + return -EOPNOTSUPP; } - if (sis96x_transaction(size)) - return -1; + status = sis96x_transaction(size); + if (status) + return status; if ((size != SIS96x_PROC_CALL) && ((read_write == I2C_SMBUS_WRITE) || (size == SIS96x_QUICK))) @@ -249,7 +242,7 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter sis96x_adapter = { .owner = THIS_MODULE, .id = I2C_HW_SMBUS_SIS96X, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; @@ -286,6 +279,10 @@ static int __devinit sis96x_probe(struct pci_dev *dev, dev_info(&dev->dev, "SiS96x SMBus base address: 0x%04x\n", sis96x_smbus_base); + retval = acpi_check_resource_conflict(&dev->resource[SIS96x_BAR]); + if (retval) + return retval; + /* Everything is happy, let's grab the memory and set things up. */ if (!request_region(sis96x_smbus_base, SMB_IOSIZE, sis96x_driver.name)) { diff --git a/drivers/i2c/busses/i2c-stub.c b/drivers/i2c/busses/i2c-stub.c index d08eeec53913..1b7b2af94036 100644 --- a/drivers/i2c/busses/i2c-stub.c +++ b/drivers/i2c/busses/i2c-stub.c @@ -43,7 +43,7 @@ struct stub_chip { static struct stub_chip *stub_chips; -/* Return -1 on error. */ +/* Return negative errno on error. */ static s32 stub_xfer(struct i2c_adapter * adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data * data) { @@ -120,7 +120,7 @@ static s32 stub_xfer(struct i2c_adapter * adap, u16 addr, unsigned short flags, default: dev_dbg(&adap->dev, "Unsupported I2C/SMBus command\n"); - ret = -1; + ret = -EOPNOTSUPP; break; } /* switch (size) */ @@ -140,7 +140,7 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter stub_adapter = { .owner = THIS_MODULE, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, .name = "SMBus stub driver", }; diff --git a/drivers/i2c/busses/i2c-taos-evm.c b/drivers/i2c/busses/i2c-taos-evm.c index de9db49e54d9..224aa12ee7c8 100644 --- a/drivers/i2c/busses/i2c-taos-evm.c +++ b/drivers/i2c/busses/i2c-taos-evm.c @@ -96,9 +96,8 @@ static int taos_smbus_xfer(struct i2c_adapter *adapter, u16 addr, sprintf(p, "$%02X", command); break; default: - dev_dbg(&adapter->dev, "Unsupported transaction size %d\n", - size); - return -EINVAL; + dev_warn(&adapter->dev, "Unsupported transaction %d\n", size); + return -EOPNOTSUPP; } /* Send the transaction to the TAOS EVM */ diff --git a/drivers/i2c/busses/i2c-via.c b/drivers/i2c/busses/i2c-via.c index 61716f6b14dc..29cef0433f34 100644 --- a/drivers/i2c/busses/i2c-via.c +++ b/drivers/i2c/busses/i2c-via.c @@ -1,7 +1,4 @@ /* - i2c-via.c - Part of lm_sensors, Linux kernel modules - for hardware monitoring - i2c Support for Via Technologies 82C586B South Bridge Copyright (c) 1998, 1999 Kyösti Mälkki <kmalkki@cc.hut.fi> @@ -87,7 +84,7 @@ static struct i2c_algo_bit_data bit_data = { static struct i2c_adapter vt586b_adapter = { .owner = THIS_MODULE, .id = I2C_HW_B_VIA, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .name = "VIA i2c", .algo_data = &bit_data, }; diff --git a/drivers/i2c/busses/i2c-viapro.c b/drivers/i2c/busses/i2c-viapro.c index 77b13d027f86..862eb352a2d9 100644 --- a/drivers/i2c/busses/i2c-viapro.c +++ b/drivers/i2c/busses/i2c-viapro.c @@ -1,6 +1,4 @@ /* - i2c-viapro.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring Copyright (c) 1998 - 2002 Frodo Looijaard <frodol@dds.nl>, Philip Edelbrock <phil@netroedge.com>, Kyösti Mälkki <kmalkki@cc.hut.fi>, Mark D. Studebaker <mdsxyz123@yahoo.com> @@ -50,6 +48,7 @@ #include <linux/ioport.h> #include <linux/i2c.h> #include <linux/init.h> +#include <linux/acpi.h> #include <asm/io.h> static struct pci_dev *vt596_pdev; @@ -152,7 +151,7 @@ static int vt596_transaction(u8 size) if ((temp = inb_p(SMBHSTSTS)) & 0x1F) { dev_err(&vt596_adapter.dev, "SMBus reset failed! " "(0x%02x)\n", temp); - return -1; + return -EBUSY; } } @@ -167,24 +166,24 @@ static int vt596_transaction(u8 size) /* If the SMBus is still busy, we give up */ if (timeout >= MAX_TIMEOUT) { - result = -1; + result = -ETIMEDOUT; dev_err(&vt596_adapter.dev, "SMBus timeout!\n"); } if (temp & 0x10) { - result = -1; + result = -EIO; dev_err(&vt596_adapter.dev, "Transaction failed (0x%02x)\n", size); } if (temp & 0x08) { - result = -1; + result = -EIO; dev_err(&vt596_adapter.dev, "SMBus collision!\n"); } if (temp & 0x04) { int read = inb_p(SMBHSTADD) & 0x01; - result = -1; + result = -ENXIO; /* The quick and receive byte commands are used to probe for chips, so errors are expected, and we don't want to frighten the user. */ @@ -202,12 +201,13 @@ static int vt596_transaction(u8 size) return result; } -/* Return -1 on error, 0 on success */ +/* Return negative errno on error, 0 on success */ static s32 vt596_access(struct i2c_adapter *adap, u16 addr, unsigned short flags, char read_write, u8 command, int size, union i2c_smbus_data *data) { int i; + int status; switch (size) { case I2C_SMBUS_QUICK: @@ -258,8 +258,9 @@ static s32 vt596_access(struct i2c_adapter *adap, u16 addr, outb_p(((addr & 0x7f) << 1) | read_write, SMBHSTADD); - if (vt596_transaction(size)) /* Error in transaction */ - return -1; + status = vt596_transaction(size); + if (status) + return status; if ((read_write == I2C_SMBUS_WRITE) || (size == VT596_QUICK)) return 0; @@ -285,9 +286,9 @@ static s32 vt596_access(struct i2c_adapter *adap, u16 addr, return 0; exit_unsupported: - dev_warn(&vt596_adapter.dev, "Unsupported command invoked! (0x%02x)\n", + dev_warn(&vt596_adapter.dev, "Unsupported transaction %d\n", size); - return -1; + return -EOPNOTSUPP; } static u32 vt596_func(struct i2c_adapter *adapter) @@ -309,7 +310,7 @@ static const struct i2c_algorithm smbus_algorithm = { static struct i2c_adapter vt596_adapter = { .owner = THIS_MODULE, .id = I2C_HW_SMBUS_VIA2, - .class = I2C_CLASS_HWMON, + .class = I2C_CLASS_HWMON | I2C_CLASS_SPD, .algo = &smbus_algorithm, }; @@ -354,6 +355,10 @@ static int __devinit vt596_probe(struct pci_dev *pdev, } found: + error = acpi_check_region(vt596_smba, 8, vt596_driver.name); + if (error) + return error; + if (!request_region(vt596_smba, 8, vt596_driver.name)) { dev_err(&pdev->dev, "SMBus region 0x%x already in use!\n", vt596_smba); diff --git a/drivers/i2c/busses/i2c-voodoo3.c b/drivers/i2c/busses/i2c-voodoo3.c index 88a3447e11e1..1d4ae26ba73d 100644 --- a/drivers/i2c/busses/i2c-voodoo3.c +++ b/drivers/i2c/busses/i2c-voodoo3.c @@ -1,6 +1,4 @@ /* - voodoo3.c - Part of lm_sensors, Linux kernel modules for hardware - monitoring Copyright (c) 1998, 1999 Frodo Looijaard <frodol@dds.nl>, Philip Edelbrock <phil@netroedge.com>, Ralph Metzler <rjkm@thp.uni-koeln.de>, and diff --git a/drivers/i2c/busses/scx200_acb.c b/drivers/i2c/busses/scx200_acb.c index 61abe0f33255..ed794b145a11 100644 --- a/drivers/i2c/busses/scx200_acb.c +++ b/drivers/i2c/busses/scx200_acb.c @@ -442,7 +442,7 @@ static __init struct scx200_acb_iface *scx200_create_iface(const char *text, adapter->owner = THIS_MODULE; adapter->id = I2C_HW_SMBUS_SCX200; adapter->algo = &scx200_acb_algorithm; - adapter->class = I2C_CLASS_HWMON; + adapter->class = I2C_CLASS_HWMON | I2C_CLASS_SPD; adapter->dev.parent = dev; mutex_init(&iface->mutex); |