| Commit message (Expand) | Author | Age | Files | Lines |
* | powerpc/86xx: Move dts files to fsl directory | Alessio Igor Bogani | 2016-03-12 | 1 | -423/+0 |
* | dt/bindings: Remove all references to device_type "ethernet-phy" | Grant Likely | 2014-01-16 | 1 | -2/+0 |
* | powerpc/fsl: update compatiable on fsl 16550 uart nodes | Kumar Gala | 2012-01-04 | 1 | -2/+2 |
* | powerpc/86xx: Correct Gianfar support for GE boards | Martyn Welch | 2011-11-03 | 1 | -4/+29 |
* | powerpc/86xx: Renaming following split of GE Fanuc joint venture | Martyn Welch | 2010-03-04 | 1 | -2/+2 |
* | powerpc/86xx: Basic flash support for GE SBC610 | Martyn Welch | 2010-02-18 | 1 | -8/+42 |
* | powerpc/86xx: Add MSI section to GE SBC610 DTS | Malcolm Crossley | 2010-02-18 | 1 | -0/+16 |
* | powerpc/86xx: Enable NVRAM on GE Fanuc's SBC610 | Martyn Welch | 2009-11-20 | 1 | -0/+6 |
* | powerpc/86xx: Add I2C device mappings in DTS for SBC610 | Martyn Welch | 2009-06-16 | 1 | -0/+10 |
* | powerpc/fsl: Removed reg property from 85xx/86xx soc node | Kumar Gala | 2009-05-19 | 1 | -1/+0 |
* | powerpc/86xx: Add new LAW & MCM device tree nodes for all 86xx systems | Kumar Gala | 2009-05-19 | 1 | -0/+13 |
* | powerpc/86xx: Move gianfar mdio nodes under the ethernet nodes | Anton Vorontsov | 2009-03-24 | 1 | -18/+21 |
* | powerpc/86xx: Correct local bus registers in GE Fanuc SBC610 dts file | Martyn Welch | 2009-03-09 | 1 | -1/+1 |
* | [WATCHDOG] Enable watchdog timer on GE Fanuc's SBC610 | Martyn Welch | 2009-01-12 | 1 | -0/+15 |
* | powerpc/86xx: Basic GPIO support for GE Fanuc SBC610 | Martyn Welch | 2008-12-03 | 1 | -0/+6 |
* | powerpc/86xx: Add use of Epson RTX-8581 RTC to GE Fanuc SBC610 dts | Martyn Welch | 2008-12-03 | 1 | -0/+5 |
* | powerpc/86xx: Correct SOC bus-frequency in GE Fanuc SBC610 DTS | Martyn Welch | 2008-11-08 | 1 | -1/+1 |
* | powerpc: FPGA support for GE Fanuc SBC610 | Martyn Welch | 2008-10-13 | 1 | -0/+4 |
* | powerpc: GE Fanuc's FPGA based PIC controller on the SBC610 | Martyn Welch | 2008-10-13 | 1 | -4/+33 |
* | powerpc: Board support for GE Fanuc SBC610 | Martyn Welch | 2008-09-16 | 1 | -0/+260 |