blob: 2460ccc082371b08999c47f940cc71805568103d (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/wireless/microchip,wilc1000.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Microchip WILC wireless
maintainers:
- Adham Abozaeid <adham.abozaeid@microchip.com>
- Ajay Singh <ajay.kathat@microchip.com>
description:
The wilc1000 chips can be connected via SPI or SDIO. This document
describes the binding to connect wilc devices.
properties:
compatible:
const: microchip,wilc1000
reg: true
interrupts:
maxItems: 1
clocks:
description: phandle to the clock connected on rtc clock line.
maxItems: 1
clock-names:
const: rtc
enable-gpios:
maxItems: 1
description: Used by wilc1000-spi to determine the GPIO line
connected to the ENABLE line. If specified, reset-gpios
must be specified as well as otherwise the driver cannot
ensure the timing required between asserting ENABLE
and deasserting RESET. This should be declared as an
active-high signal.
reset-gpios:
maxItems: 1
description: Used by wilc1000-spi to determine the GPIO line
connected to the RESET line. This should be declared as an
active-low signal.
required:
- compatible
- interrupts
allOf:
- $ref: /schemas/spi/spi-peripheral-props.yaml#
unevaluatedProperties: false
examples:
- |
#include <dt-bindings/gpio/gpio.h>
spi {
#address-cells = <1>;
#size-cells = <0>;
wifi@0 {
compatible = "microchip,wilc1000";
spi-max-frequency = <48000000>;
reg = <0>;
interrupt-parent = <&pioC>;
interrupts = <27 0>;
clocks = <&pck1>;
clock-names = "rtc";
enable-gpios = <&pioA 5 GPIO_ACTIVE_HIGH>;
reset-gpios = <&pioA 6 GPIO_ACTIVE_LOW>;
};
};
- |
mmc {
#address-cells = <1>;
#size-cells = <0>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_mmc1_clk_cmd_dat0 &pinctrl_mmc1_dat1_3>;
non-removable;
vmmc-supply = <&vcc_mmc1_reg>;
vqmmc-supply = <&vcc_3v3_reg>;
bus-width = <4>;
wifi@0 {
compatible = "microchip,wilc1000";
reg = <0>;
interrupt-parent = <&pioC>;
interrupts = <27 0>;
clocks = <&pck1>;
clock-names = "rtc";
};
};
|
