1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
|
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/remoteproc/st,stm32-rproc.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: STMicroelectronics STM32 remote processor controller
description:
This document defines the binding for the remoteproc component that loads and
boots firmwares on the ST32MP family chipset.
maintainers:
- Fabien Dessenne <fabien.dessenne@foss.st.com>
- Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
properties:
compatible:
const: st,stm32mp1-m4
reg:
description:
Address ranges of the RETRAM and MCU SRAM memories used by the remote
processor.
maxItems: 3
resets:
maxItems: 1
st,syscfg-holdboot:
description: remote processor reset hold boot
$ref: /schemas/types.yaml#/definitions/phandle-array
items:
- items:
- description: Phandle of syscon block
- description: The offset of the hold boot setting register
- description: The field mask of the hold boot
st,syscfg-tz:
description:
Reference to the system configuration which holds the RCC trust zone mode
$ref: /schemas/types.yaml#/definitions/phandle-array
items:
- items:
- description: Phandle of syscon block
- description: The offset of the trust zone setting register
- description: The field mask of the trust zone state
interrupts:
description: Should contain the WWDG1 watchdog reset interrupt
maxItems: 1
wakeup-source: true
mboxes:
description:
This property is required only if the rpmsg/virtio functionality is used.
items:
- description: |
A channel (a) used to communicate through virtqueues with the
remote proc.
Bi-directional channel:
- from local to remote = send message
- from remote to local = send message ack
- description: |
A channel (b) working the opposite direction of channel (a)
- description: |
A channel (c) used by the local proc to notify the remote proc that it
is about to be shut down.
Unidirectional channel:
- from local to remote, where ACK from the remote means that it is
ready for shutdown
- description: |
A channel (d) used by the local proc to notify the remote proc that it
has to stop interprocessor communication.
Unidirectional channel:
- from local to remote, where ACK from the remote means that communication
as been stopped on the remote side.
minItems: 1
mbox-names:
items:
- const: vq0
- const: vq1
- const: shutdown
- const: detach
minItems: 1
memory-region:
description:
List of phandles to the reserved memory regions associated with the
remoteproc device. This is variable and describes the memories shared with
the remote processor (e.g. remoteproc firmware and carveouts, rpmsg
vrings, ...).
(see ../reserved-memory/reserved-memory.txt)
st,syscfg-pdds:
$ref: /schemas/types.yaml#/definitions/phandle-array
description: |
Reference to the system configuration which holds the remote
items:
- items:
- description: Phandle of syscon block
- description: The offset of the power setting register
- description: The field mask of the PDDS selection
st,syscfg-m4-state:
$ref: /schemas/types.yaml#/definitions/phandle-array
description: |
Reference to the tamp register which exposes the Cortex-M4 state.
items:
- items:
- description: Phandle of syscon block with the tamp register
- description: The offset of the tamp register
- description: The field mask of the Cortex-M4 state
st,syscfg-rsc-tbl:
$ref: /schemas/types.yaml#/definitions/phandle-array
description: |
Reference to the tamp register which references the Cortex-M4
resource table address.
items:
- items:
- description: Phandle of syscon block with the tamp register
- description: The offset of the tamp register
- description: The field mask of the Cortex-M4 resource table address
st,auto-boot:
$ref: /schemas/types.yaml#/definitions/flag
description:
If defined, when remoteproc is probed, it loads the default firmware and
starts the remote processor.
required:
- compatible
- reg
- resets
- st,syscfg-holdboot
- st,syscfg-tz
additionalProperties: false
examples:
- |
#include <dt-bindings/reset/stm32mp1-resets.h>
m4_rproc: m4@10000000 {
compatible = "st,stm32mp1-m4";
reg = <0x10000000 0x40000>,
<0x30000000 0x40000>,
<0x38000000 0x10000>;
resets = <&rcc MCU_R>;
st,syscfg-holdboot = <&rcc 0x10C 0x1>;
st,syscfg-tz = <&rcc 0x000 0x1>;
st,syscfg-rsc-tbl = <&tamp 0x144 0xFFFFFFFF>;
st,syscfg-m4-state = <&tamp 0x148 0xFFFFFFFF>;
};
...
|
