1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
|
QCOM GSBI (General Serial Bus Interface) Driver
The GSBI controller is modeled as a node with zero or more child nodes, each
representing a serial sub-node device that is mux'd as part of the GSBI
configuration settings. The mode setting will govern the input/output mode of
the 4 GSBI IOs.
Required properties:
- compatible: must contain "qcom,gsbi-v1.0.0" for APQ8064/IPQ8064
- reg: Address range for GSBI registers
- clocks: required clock
- clock-names: must contain "iface" entry
- qcom,mode : indicates MUX value for configuration of the serial interface.
Please reference dt-bindings/soc/qcom,gsbi.h for valid mux values.
Optional properties:
- qcom,crci : indicates CRCI MUX value for QUP CRCI ports. Please reference
dt-bindings/soc/qcom,gsbi.h for valid CRCI mux values.
Required properties if child node exists:
- #address-cells: Must be 1
- #size-cells: Must be 1
- ranges: Must be present
Properties for children:
A GSBI controller node can contain 0 or more child nodes representing serial
devices. These serial devices can be a QCOM UART, I2C controller, spi
controller, or some combination of aforementioned devices.
See the following for child node definitions:
Documentation/devicetree/bindings/i2c/qcom,i2c-qup.txt
Documentation/devicetree/bindings/spi/qcom,spi-qup.txt
Documentation/devicetree/bindings/serial/qcom,msm-uartdm.txt
Example for APQ8064:
#include <dt-bindings/soc/qcom,gsbi.h>
gsbi4@16300000 {
compatible = "qcom,gsbi-v1.0.0";
reg = <0x16300000 0x100>;
clocks = <&gcc GSBI4_H_CLK>;
clock-names = "iface";
#address-cells = <1>;
#size-cells = <1>;
ranges;
qcom,mode = <GSBI_PROT_I2C_UART>;
qcom,crci = <GSBI_CRCI_QUP>;
/* child nodes go under here */
i2c_qup4: i2c@16380000 {
compatible = "qcom,i2c-qup-v1.1.1";
reg = <0x16380000 0x1000>;
interrupts = <0 153 0>;
clocks = <&gcc GSBI4_QUP_CLK>, <&gcc GSBI4_H_CLK>;
clock-names = "core", "iface";
clock-frequency = <200000>;
#address-cells = <1>;
#size-cells = <0>;
};
uart4: serial@16340000 {
compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
reg = <0x16340000 0x1000>,
<0x16300000 0x1000>;
interrupts = <0 152 0x0>;
clocks = <&gcc GSBI4_UART_CLK>, <&gcc GSBI4_H_CLK>;
clock-names = "core", "iface";
status = "ok";
};
};
|