1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
|
Renesas R-Car sound
=============================================
* Modules
=============================================
Renesas R-Car and RZ/G sound is constructed from below modules
(for Gen2 or later)
SCU : Sampling Rate Converter Unit
- SRC : Sampling Rate Converter
- CMD
- CTU : Channel Transfer Unit
- MIX : Mixer
- DVC : Digital Volume and Mute Function
SSIU : Serial Sound Interface Unit
SSI : Serial Sound Interface
See detail of each module's channels, connection, limitation on datasheet
=============================================
* Multi channel
=============================================
Multi channel is supported by Multi-SSI, or TDM-SSI.
Multi-SSI : 6ch case, you can use stereo x 3 SSI
TDM-SSI : 6ch case, you can use TDM
=============================================
* Enable/Disable each modules
=============================================
See datasheet to check SRC/CTU/MIX/DVC connect-limitation.
DT controls enabling/disabling module.
${LINUX}/arch/arm/boot/dts/r8a7790-lager.dts can be good example.
This is example of
Playback: [MEM] -> [SRC2] -> [DVC0] -> [SSIU0/SSI0] -> [codec]
Capture: [MEM] <- [DVC1] <- [SRC3] <- [SSIU1/SSI1] <- [codec]
see "Example: simple sound card"
You can use below.
${LINUX}/arch/arm/boot/dts/r8a7790.dts can be good example.
&src0 &ctu00 &mix0 &dvc0 &ssi0
&src1 &ctu01 &mix1 &dvc1 &ssi1
&src2 &ctu02 &ssi2
&src3 &ctu03 &ssi3
&src4 &ssi4
&src5 &ctu10 &ssi5
&src6 &ctu11 &ssi6
&src7 &ctu12 &ssi7
&src8 &ctu13 &ssi8
&src9 &ssi9
=============================================
* SRC (Sampling Rate Converter)
=============================================
[xx]Hz [yy]Hz
------> [SRC] ------>
SRC can convert [xx]Hz to [yy]Hz. Then, it has below 2 modes
Asynchronous mode: input data / output data are based on different clocks.
you can use this mode on Playback / Capture
Synchronous mode: input data / output data are based on same clocks.
This mode will be used if system doesn't have its input clock,
for example digital TV case.
you can use this mode on Playback
------------------
** Asynchronous mode
------------------
You need to use "simple-scu-audio-card" or "audio-graph-scu-card" for it.
see "Example: simple sound card for Asynchronous mode"
------------------
** Synchronous mode
------------------
> amixer set "SRC Out Rate" on
> aplay xxxx.wav
> amixer set "SRC Out Rate" 48000
> amixer set "SRC Out Rate" 44100
=============================================
* CTU (Channel Transfer Unit)
=============================================
[xx]ch [yy]ch
------> [CTU] -------->
CTU can convert [xx]ch to [yy]ch, or exchange outputed channel.
CTU conversion needs matrix settings.
For more detail information, see below
Renesas R-Car datasheet
- Sampling Rate Converter Unit (SCU)
- SCU Operation
- CMD Block
- Functional Blocks in CMD
Renesas R-Car datasheet
- Sampling Rate Converter Unit (SCU)
- Register Description
- CTUn Scale Value exx Register (CTUn_SVxxR)
${LINUX}/sound/soc/sh/rcar/ctu.c
- comment of header
You need to use "simple-scu-audio-card" or "audio-graph-scu-card" for it.
see "Example: simple sound card for channel convert"
Ex) Exchange output channel
Input -> Output
1ch -> 0ch
0ch -> 1ch
example of using matrix
output 0ch = (input 0ch x 0) + (input 1ch x 1)
output 1ch = (input 0ch x 1) + (input 1ch x 0)
amixer set "CTU Reset" on
amixer set "CTU Pass" 9,10
amixer set "CTU SV0" 0,4194304
amixer set "CTU SV1" 4194304,0
example of changing connection
amixer set "CTU Reset" on
amixer set "CTU Pass" 2,1
=============================================
* MIX (Mixer)
=============================================
MIX merges 2 sounds path. You can see 2 sound interface on system,
and these sounds will be merged by MIX.
aplay -D plughw:0,0 xxxx.wav &
aplay -D plughw:0,1 yyyy.wav
You need to use "simple-scu-audio-card" or "audio-graph-scu-card" for it.
Ex)
[MEM] -> [SRC1] -> [CTU02] -+-> [MIX0] -> [DVC0] -> [SSI0]
|
[MEM] -> [SRC2] -> [CTU03] -+
see "Example: simple sound card for MIXer"
=============================================
* DVC (Digital Volume and Mute Function)
=============================================
DVC controls Playback/Capture volume.
Playback Volume
amixer set "DVC Out" 100%
Capture Volume
amixer set "DVC In" 100%
Playback Mute
amixer set "DVC Out Mute" on
Capture Mute
amixer set "DVC In Mute" on
Volume Ramp
amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
amixer set "DVC Out Ramp" on
aplay xxx.wav &
amixer set "DVC Out" 80% // Volume Down
amixer set "DVC Out" 100% // Volume Up
=============================================
* SSIU (Serial Sound Interface Unit)
=============================================
SSIU can avoid some under/over run error, because it has some buffer.
But you can't use it if SSI was PIO mode.
In DMA mode, you can select not to use SSIU by using "no-busif" via SSI.
SSIU handles BUSIF which will be used for TDM Split mode.
This driver is assuming that audio-graph card will be used.
TDM Split mode merges 4 sounds. You can see 4 sound interface on system,
and these sounds will be merged SSIU/SSI.
aplay -D plughw:0,0 xxxx.wav &
aplay -D plughw:0,1 xxxx.wav &
aplay -D plughw:0,2 xxxx.wav &
aplay -D plughw:0,3 xxxx.wav
2ch 8ch
[MEM] -> [SSIU 30] -+-> [SSIU 3] --> [Codec]
2ch |
[MEM] -> [SSIU 31] -+
2ch |
[MEM] -> [SSIU 32] -+
2ch |
[MEM] -> [SSIU 33] -+
see "Example: simple sound card for TDM Split"
=============================================
* SSI (Serial Sound Interface)
=============================================
** PIO mode
You can use PIO mode which is for connection check by using.
Note: The system will drop non-SSI modules in PIO mode
even though if DT is selecting other modules.
&ssi0 {
pio-transfer
};
** DMA mode without SSIU
You can use DMA without SSIU.
Note: under/over run, or noise are likely to occur
&ssi0 {
no-busif;
};
** PIN sharing
Each SSI can share WS pin. It is based on platform.
This is example if SSI1 want to share WS pin with SSI0
&ssi1 {
shared-pin;
};
** Multi-SSI
You can use Multi-SSI.
This is example of SSI0/SSI1/SSI2 (= for 6ch)
see "Example: simple sound card for Multi channel"
** TDM-SSI
You can use TDM with SSI.
This is example of TDM 6ch.
Driver can automatically switches TDM <-> stereo mode in this case.
see "Example: simple sound card for TDM"
|
