1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
.. SPDX-License-Identifier: GPL-2.0
======================
Generic vcpu interface
======================
The virtual cpu "device" also accepts the ioctls KVM_SET_DEVICE_ATTR,
KVM_GET_DEVICE_ATTR, and KVM_HAS_DEVICE_ATTR. The interface uses the same struct
kvm_device_attr as other devices, but targets VCPU-wide settings and controls.
The groups and attributes per virtual cpu, if any, are architecture specific.
1. GROUP: KVM_ARM_VCPU_PMU_V3_CTRL
==================================
:Architectures: ARM64
1.1. ATTRIBUTE: KVM_ARM_VCPU_PMU_V3_IRQ
---------------------------------------
:Parameters: in kvm_device_attr.addr the address for PMU overflow interrupt is a
pointer to an int
Returns:
======= ========================================================
-EBUSY The PMU overflow interrupt is already set
-EFAULT Error reading interrupt number
-ENXIO The overflow interrupt not set when attempting to get it
-ENODEV PMUv3 not supported
-EINVAL Invalid PMU overflow interrupt number supplied or
trying to set the IRQ number without using an in-kernel
irqchip.
======= ========================================================
A value describing the PMUv3 (Performance Monitor Unit v3) overflow interrupt
number for this vcpu. This interrupt could be a PPI or SPI, but the interrupt
type must be same for each vcpu. As a PPI, the interrupt number is the same for
all vcpus, while as an SPI it must be a separate number per vcpu.
1.2 ATTRIBUTE: KVM_ARM_VCPU_PMU_V3_INIT
---------------------------------------
:Parameters: no additional parameter in kvm_device_attr.addr
Returns:
======= ======================================================
-EEXIST Interrupt number already used
-ENODEV PMUv3 not supported or GIC not initialized
-ENXIO PMUv3 not properly configured or in-kernel irqchip not
configured as required prior to calling this attribute
-EBUSY PMUv3 already initialized
======= ======================================================
Request the initialization of the PMUv3. If using the PMUv3 with an in-kernel
virtual GIC implementation, this must be done after initializing the in-kernel
irqchip.
1.3 ATTRIBUTE: KVM_ARM_VCPU_PMU_V3_FILTER
-----------------------------------------
:Parameters: in kvm_device_attr.addr the address for a PMU event filter is a
pointer to a struct kvm_pmu_event_filter
:Returns:
======= ======================================================
-ENODEV: PMUv3 not supported or GIC not initialized
-ENXIO: PMUv3 not properly configured or in-kernel irqchip not
configured as required prior to calling this attribute
-EBUSY: PMUv3 already initialized
-EINVAL: Invalid filter range
======= ======================================================
Request the installation of a PMU event filter described as follows:
struct kvm_pmu_event_filter {
__u16 base_event;
__u16 nevents;
#define KVM_PMU_EVENT_ALLOW 0
#define KVM_PMU_EVENT_DENY 1
__u8 action;
__u8 pad[3];
};
A filter range is defined as the range [@base_event, @base_event + @nevents),
together with an @action (KVM_PMU_EVENT_ALLOW or KVM_PMU_EVENT_DENY). The
first registered range defines the global policy (global ALLOW if the first
@action is DENY, global DENY if the first @action is ALLOW). Multiple ranges
can be programmed, and must fit within the event space defined by the PMU
architecture (10 bits on ARMv8.0, 16 bits from ARMv8.1 onwards).
Note: "Cancelling" a filter by registering the opposite action for the same
range doesn't change the default action. For example, installing an ALLOW
filter for event range [0:10) as the first filter and then applying a DENY
action for the same range will leave the whole range as disabled.
Restrictions: Event 0 (SW_INCR) is never filtered, as it doesn't count a
hardware event. Filtering event 0x1E (CHAIN) has no effect either, as it
isn't strictly speaking an event. Filtering the cycle counter is possible
using event 0x11 (CPU_CYCLES).
2. GROUP: KVM_ARM_VCPU_TIMER_CTRL
=================================
:Architectures: ARM, ARM64
2.1. ATTRIBUTES: KVM_ARM_VCPU_TIMER_IRQ_VTIMER, KVM_ARM_VCPU_TIMER_IRQ_PTIMER
-----------------------------------------------------------------------------
:Parameters: in kvm_device_attr.addr the address for the timer interrupt is a
pointer to an int
Returns:
======= =================================
-EINVAL Invalid timer interrupt number
-EBUSY One or more VCPUs has already run
======= =================================
A value describing the architected timer interrupt number when connected to an
in-kernel virtual GIC. These must be a PPI (16 <= intid < 32). Setting the
attribute overrides the default values (see below).
============================= ==========================================
KVM_ARM_VCPU_TIMER_IRQ_VTIMER The EL1 virtual timer intid (default: 27)
KVM_ARM_VCPU_TIMER_IRQ_PTIMER The EL1 physical timer intid (default: 30)
============================= ==========================================
Setting the same PPI for different timers will prevent the VCPUs from running.
Setting the interrupt number on a VCPU configures all VCPUs created at that
time to use the number provided for a given timer, overwriting any previously
configured values on other VCPUs. Userspace should configure the interrupt
numbers on at least one VCPU after creating all VCPUs and before running any
VCPUs.
3. GROUP: KVM_ARM_VCPU_PVTIME_CTRL
==================================
:Architectures: ARM64
3.1 ATTRIBUTE: KVM_ARM_VCPU_PVTIME_IPA
--------------------------------------
:Parameters: 64-bit base address
Returns:
======= ======================================
-ENXIO Stolen time not implemented
-EEXIST Base address already set for this VCPU
-EINVAL Base address not 64 byte aligned
======= ======================================
Specifies the base address of the stolen time structure for this VCPU. The
base address must be 64 byte aligned and exist within a valid guest memory
region. See Documentation/virt/kvm/arm/pvtime.rst for more information
including the layout of the stolen time structure.
|
