diff options
Diffstat (limited to 'Documentation/ABI')
| -rw-r--r-- | Documentation/ABI/stable/sysfs-bus-nvmem | 2 | ||||
| -rw-r--r-- | Documentation/ABI/testing/debugfs-iio-ad9467 | 39 | ||||
| -rw-r--r-- | Documentation/ABI/testing/debugfs-iio-backend | 20 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio | 76 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-adc-max9611 | 17 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-chemical-sgp40 | 14 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-dac | 61 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-dac-ltc2688 | 31 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-filter-admv8818 | 2 | ||||
| -rw-r--r-- | Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc | 9 |
10 files changed, 185 insertions, 86 deletions
diff --git a/Documentation/ABI/stable/sysfs-bus-nvmem b/Documentation/ABI/stable/sysfs-bus-nvmem index aa89adf18bc5..0ae8cb074acf 100644 --- a/Documentation/ABI/stable/sysfs-bus-nvmem +++ b/Documentation/ABI/stable/sysfs-bus-nvmem @@ -11,7 +11,7 @@ Description: Read returns '0' or '1' for read-write or read-only modes respectively. Write parses one of 'YyTt1NnFf0', or [oO][NnFf] for "on" - and "off", i.e. what kstrbool() supports. + and "off", i.e. what kstrtobool() supports. Note: This file is only present if CONFIG_NVMEM_SYSFS is enabled. diff --git a/Documentation/ABI/testing/debugfs-iio-ad9467 b/Documentation/ABI/testing/debugfs-iio-ad9467 new file mode 100644 index 000000000000..0352fca1f7f2 --- /dev/null +++ b/Documentation/ABI/testing/debugfs-iio-ad9467 @@ -0,0 +1,39 @@ +What: /sys/kernel/debug/iio/iio:deviceX/calibration_table_dump +KernelVersion: 6.11 +Contact: linux-iio@vger.kernel.org +Description: + This dumps the calibration table that was filled during the + digital interface tuning process. + +What: /sys/kernel/debug/iio/iio:deviceX/in_voltage_test_mode_available +KernelVersion: 6.11 +Contact: linux-iio@vger.kernel.org +Description: + List all the available test tones: + - off + - midscale_short + - pos_fullscale + - neg_fullscale + - checkerboard + - prbs23 + - prbs9 + - one_zero_toggle + - user + - bit_toggle + - sync + - one_bit_high + - mixed_bit_frequency + - ramp + + Note that depending on the actual device being used, some of the + above might not be available (and they won't be listed when + reading the file). + +What: /sys/kernel/debug/iio/iio:deviceX/in_voltageY_test_mode +KernelVersion: 6.11 +Contact: linux-iio@vger.kernel.org +Description: + Writing to this file will initiate one of available test tone on + channel Y. Reading it, shows which test is running. In cases + where an IIO backend is available and supports the test tone, + additional information about the data correctness is given. diff --git a/Documentation/ABI/testing/debugfs-iio-backend b/Documentation/ABI/testing/debugfs-iio-backend new file mode 100644 index 000000000000..01ab94469432 --- /dev/null +++ b/Documentation/ABI/testing/debugfs-iio-backend @@ -0,0 +1,20 @@ +What: /sys/kernel/debug/iio/iio:deviceX/backendY/name +KernelVersion: 6.11 +Contact: linux-iio@vger.kernel.org +Description: + Name of Backend Y connected to device X. + +What: /sys/kernel/debug/iio/iio:deviceX/backendY/direct_reg_access +KernelVersion: 6.11 +Contact: linux-iio@vger.kernel.org +Description: + Directly access the registers of backend Y. Typical usage is: + + Reading address 0x50 + echo 0x50 > direct_reg_access + cat direct_reg_access + + Writing address 0x50 + echo 0x50 0x3 > direct_reg_access + //readback address 0x50 + cat direct_reg_access diff --git a/Documentation/ABI/testing/sysfs-bus-iio b/Documentation/ABI/testing/sysfs-bus-iio index 7cee78ad4108..89943c2d54e8 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio +++ b/Documentation/ABI/testing/sysfs-bus-iio @@ -523,13 +523,27 @@ Description: What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_altvoltageY_i_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_altvoltageY_q_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_capacitance_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_illuminance_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_illuminance0_calibbias -What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibbias -What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_intensityY_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_magn_z_calibbias What: /sys/bus/iio/devices/iio:deviceX/in_pressure_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_proximity_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_resistance_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_temp_calibbias +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibbias +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_calibbias +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_calibbias KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: @@ -541,6 +555,10 @@ Description: What: /sys/bus/iio/devices/iio:deviceX/in_accel_calibbias_available What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_calibbias_available +What: /sys/bus/iio/devices/iio:deviceX/in_temp_calibbias_available +What: /sys/bus/iio/devices/iio:deviceX/in_proximity_calibbias_available +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibbias_available +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_calibbias_available KernelVersion: 5.8 Contact: linux-iio@vger.kernel.org Description: @@ -549,25 +567,34 @@ Description: - a small discrete set of values like "0 2 4 6 8" - a range specified as "[min step max]" -What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_i_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_q_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltage_i_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltage_q_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_altvoltage_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_voltage_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_accel_x_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_accel_y_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_accel_z_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_altvoltage_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_x_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_y_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_anglvel_z_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_capacitance_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_illuminance_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_illuminance0_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_intensity_both_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_intensity_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_intensity_ir_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_magn_x_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_magn_y_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_magn_z_calibscale What: /sys/bus/iio/devices/iio:deviceX/in_pressure_calibscale -What: /sys/bus/iio/devices/iio:deviceX/in_illuminance_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_pressureY_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_proximity0_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltage_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltage_i_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltage_q_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_i_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_q_calibscale +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_supply_calibscale +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_calibscale +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_calibscale KernelVersion: 2.6.35 Contact: linux-iio@vger.kernel.org Description: @@ -575,6 +602,20 @@ Description: production inaccuracies). If shared across all channels, <type>_calibscale is used. +What: /sys/bus/iio/devices/iio:deviceX/in_illuminanceY_calibscale_available +What: /sys/bus/iio/devices/iio:deviceX/in_intensityY_calibscale_available +What: /sys/bus/iio/devices/iio:deviceX/in_proximityY_calibscale_available +What: /sys/bus/iio/devices/iio:deviceX/in_voltageY_calibscale_available +KernelVersion: 4.8 +Contact: linux-iio@vger.kernel.org +Description: + Available values of calibscale. Maybe expressed as either of: + + - a small discrete set of values like "1 8 16" + - a range specified as "[min step max]" + + If shared across all channels, <type>_calibscale_available is used. + What: /sys/bus/iio/devices/iio:deviceX/in_activity_calibgender What: /sys/bus/iio/devices/iio:deviceX/in_energy_calibgender What: /sys/bus/iio/devices/iio:deviceX/in_distance_calibgender @@ -708,6 +749,7 @@ Description: 2.5kohm_to_gnd: connected to ground via a 2.5kOhm resistor, 6kohm_to_gnd: connected to ground via a 6kOhm resistor, 20kohm_to_gnd: connected to ground via a 20kOhm resistor, + 42kohm_to_gnd: connected to ground via a 42kOhm resistor, 90kohm_to_gnd: connected to ground via a 90kOhm resistor, 100kohm_to_gnd: connected to ground via an 100kOhm resistor, 125kohm_to_gnd: connected to ground via an 125kOhm resistor, @@ -2289,3 +2331,11 @@ KernelVersion: 6.7 Contact: linux-iio@vger.kernel.org Description: List of available timeout value for tap gesture confirmation. + +What: /sys/.../iio:deviceX/in_shunt_resistor +What: /sys/.../iio:deviceX/in_current_shunt_resistor +What: /sys/.../iio:deviceX/in_power_shunt_resistor +KernelVersion: 6.10 +Contact: linux-iio@vger.kernel.org +Description: + The value of current sense resistor in Ohms. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-adc-max9611 b/Documentation/ABI/testing/sysfs-bus-iio-adc-max9611 deleted file mode 100644 index 6d2d2b094941..000000000000 --- a/Documentation/ABI/testing/sysfs-bus-iio-adc-max9611 +++ /dev/null @@ -1,17 +0,0 @@ -What: /sys/bus/iio/devices/iio:deviceX/in_power_shunt_resistor -Date: March 2017 -KernelVersion: 4.12 -Contact: linux-iio@vger.kernel.org -Description: The value of the shunt resistor used to compute power drain on - common input voltage pin (RS+). In Ohms. - -What: /sys/bus/iio/devices/iio:deviceX/in_current_shunt_resistor -Date: March 2017 -KernelVersion: 4.12 -Contact: linux-iio@vger.kernel.org -Description: The value of the shunt resistor used to compute current flowing - between RS+ and RS- voltage sense inputs. In Ohms. - -These attributes describe a single physical component, exposed as two distinct -attributes as it is used to calculate two different values: power load and -current flowing between RS+ and RS- inputs. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-chemical-sgp40 b/Documentation/ABI/testing/sysfs-bus-iio-chemical-sgp40 index 469a7c00fad4..a95547e874f1 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-chemical-sgp40 +++ b/Documentation/ABI/testing/sysfs-bus-iio-chemical-sgp40 @@ -15,17 +15,3 @@ Description: Set the relative humidity. This value is sent to the sensor for humidity compensation. Default value: 50000 (50 % relative humidity) - -What: /sys/bus/iio/devices/iio:deviceX/in_resistance_calibbias -Date: August 2021 -KernelVersion: 5.15 -Contact: Andreas Klinger <ak@it-klinger.de> -Description: - Set the bias value for the resistance which is used for - calculation of in_concentration_input as follows: - - x = (in_resistance_raw - in_resistance_calibbias) * 0.65 - - in_concentration_input = 500 / (1 + e^x) - - Default value: 30000 diff --git a/Documentation/ABI/testing/sysfs-bus-iio-dac b/Documentation/ABI/testing/sysfs-bus-iio-dac new file mode 100644 index 000000000000..810eaac5533c --- /dev/null +++ b/Documentation/ABI/testing/sysfs-bus-iio-dac @@ -0,0 +1,61 @@ +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_toggle_en +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + Toggle enable. Write 1 to enable toggle or 0 to disable it. This + is useful when one wants to change the DAC output codes. For + autonomous toggling, the way it should be done is: + + - disable toggle operation; + - change out_currentY_rawN, where N is the integer value of the symbol; + - enable toggle operation. + +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_rawN +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + This attribute has the same meaning as out_currentY_raw. It is + specific to toggle enabled channels and refers to the DAC output + code in INPUT_N (_rawN), where N is the integer value of the symbol. + The same scale and offset as in out_currentY_raw applies. + +What: /sys/bus/iio/devices/iio:deviceX/out_currentY_symbol +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + Performs a SW switch to a predefined output symbol. This attribute + is specific to toggle enabled channels and allows switching between + multiple predefined symbols. Each symbol corresponds to a different + output, denoted as out_currentY_rawN, where N is the integer value + of the symbol. Writing an integer value N will select out_currentY_rawN. + +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_toggle_en +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + Toggle enable. Write 1 to enable toggle or 0 to disable it. This + is useful when one wants to change the DAC output codes. For + autonomous toggling, the way it should be done is: + + - disable toggle operation; + - change out_voltageY_rawN, where N is the integer value of the symbol; + - enable toggle operation. + +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_rawN +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + This attribute has the same meaning as out_currentY_raw. It is + specific to toggle enabled channels and refers to the DAC output + code in INPUT_N (_rawN), where N is the integer value of the symbol. + The same scale and offset as in out_currentY_raw applies. + +What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_symbol +KernelVersion: 5.18 +Contact: linux-iio@vger.kernel.org +Description: + Performs a SW switch to a predefined output symbol. This attribute + is specific to toggle enabled channels and allows switching between + multiple predefined symbols. Each symbol corresponds to a different + output, denoted as out_voltageY_rawN, where N is the integer value + of the symbol. Writing an integer value N will select out_voltageY_rawN. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-dac-ltc2688 b/Documentation/ABI/testing/sysfs-bus-iio-dac-ltc2688 index 1c35971277ba..ae95a5477382 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-dac-ltc2688 +++ b/Documentation/ABI/testing/sysfs-bus-iio-dac-ltc2688 @@ -53,34 +53,3 @@ KernelVersion: 5.18 Contact: linux-iio@vger.kernel.org Description: Returns the available values for the dither phase. - -What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_toggle_en -KernelVersion: 5.18 -Contact: linux-iio@vger.kernel.org -Description: - Toggle enable. Write 1 to enable toggle or 0 to disable it. This is - useful when one wants to change the DAC output codes. The way it should - be done is: - - - disable toggle operation; - - change out_voltageY_raw0 and out_voltageY_raw1; - - enable toggle operation. - -What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_raw0 -What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_raw1 -KernelVersion: 5.18 -Contact: linux-iio@vger.kernel.org -Description: - It has the same meaning as out_voltageY_raw. This attribute is - specific to toggle enabled channels and refers to the DAC output - code in INPUT_A (_raw0) and INPUT_B (_raw1). The same scale and offset - as in out_voltageY_raw applies. - -What: /sys/bus/iio/devices/iio:deviceX/out_voltageY_symbol -KernelVersion: 5.18 -Contact: linux-iio@vger.kernel.org -Description: - Performs a SW toggle. This attribute is specific to toggle - enabled channels and allows to toggle between out_voltageY_raw0 - and out_voltageY_raw1 through software. Writing 0 will select - out_voltageY_raw0 while 1 selects out_voltageY_raw1. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-filter-admv8818 b/Documentation/ABI/testing/sysfs-bus-iio-filter-admv8818 index 31dbb390573f..c431f0a13cf5 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-filter-admv8818 +++ b/Documentation/ABI/testing/sysfs-bus-iio-filter-admv8818 @@ -3,7 +3,7 @@ KernelVersion: Contact: linux-iio@vger.kernel.org Description: Reading this returns the valid values that can be written to the - on_altvoltage0_mode attribute: + filter_mode attribute: - auto -> Adjust bandpass filter to track changes in input clock rate. - manual -> disable/unregister the clock rate notifier / input clock tracking. diff --git a/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc b/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc index 8916f7ec6507..8dbca113112d 100644 --- a/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc +++ b/Documentation/ABI/testing/sysfs-bus-iio-ina2xx-adc @@ -13,12 +13,3 @@ Description: available for reading data. However, samples can be occasionally skipped or repeated, depending on the beat between the capture and conversion rates. - -What: /sys/bus/iio/devices/iio:deviceX/in_shunt_resistor -Date: December 2015 -KernelVersion: 4.4 -Contact: linux-iio@vger.kernel.org -Description: - The value of the shunt resistor may be known only at runtime fom an - eeprom content read by a client application. This attribute allows to - set its value in ohms. |